The starting of AP interface can fail due to invalid
beacon interval, which does not match the minimum gcd
requirement set by the wifi driver. In such case, the
beacon interval of that interface gets updated with
that invalid beacon interval.

The next time that interface is brought up in AP mode,
an interface combination check is performed and the
beacon interval is taken from the previously set value.

In a case where an invalid beacon interval, i.e. a beacon
interval value which does not satisfy the minimum gcd criteria
set by the driver, is set, all the subsequent trials to
bring that interface in AP mode will fail, even if the
subsequent trials have a valid beacon interval.

To avoid this, in case of a failure in bringing up an
interface in AP mode due to interface combination error,
the interface beacon interval which is stored in bss
conf, needs to be restored with the last working value
of beacon interval.

Tested on ath10k using WCN3990.

Cc: stable@vger.kernel.org
Fixes: 0c317a02 ("cfg80211: support virtual interfaces with different beacon intervals")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When rhashtable insertion fails the mesh table code doesn't free
the now-orphan mesh path object.  This patch fixes that.

Cc: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The mesh table code walks over hash tables for two purposes.  First of
all it's used as part of a netlink dump process, but it is also used
for looking up entries to delete using criteria other than the hash
key.

The second purpose is directly contrary to the design specification
of rhashtable walks.  It is only meant for use by netlink dumps.

This is because rhashtable is resizable and you cannot obtain a
stable walk over it during a resize process.

In fact mesh's use of rhashtable for dumping is bogus too.  Rather
than using rhashtable walk's iterator to keep track of the current
position, it always converts the current position to an integer
which defeats the purpose of the iterator.

Therefore this patch converts all uses of rhashtable walk into a
simple linked list.

This patch also adds a new spin lock to protect the hash table
insertion/removal as well as the walk list modifications.  In fact
the previous code was buggy as the removals can race with each
other, potentially resulting in a double-free.

Cc: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Currently the ethtool_regs version is set to 0 for FEC devices.

Use this field to store the register dump version exposed by the
kernel. The choosen version 2 corresponds to the kernel compile test:

        #if defined(CONFIG_M523x) || defined(CONFIG_M527x)
        || defined(CONFIG_M528x) || defined(CONFIG_M520x)
        || defined(CONFIG_M532x) || defined(CONFIG_ARM)
        || defined(CONFIG_ARM64) || defined(CONFIG_COMPILE_TEST)

and version 1 corresponds to the opposite. Binaries of ethtool unaware
of this version will dump the whole set as usual.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The of_find_device_by_node() takes a reference to the underlying device
structure, we should release that reference.
Signed-off-by: Huang Zijiang <huang.zijiang@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

The basic idea behind ->pagecnt_bias is: If we pre-allocate the maximum
number of references that we might need to create in the fastpath later,
the bump-allocation fastpath only has to modify the non-atomic bias value
that tracks the number of extra references we hold instead of the atomic
refcount. The maximum number of allocations we can serve (under the
assumption that no allocation is made with size 0) is nc->size, so that's
the bias used.

However, even when all memory in the allocation has been given away, a
reference to the page is still held; and in the `offset < 0` slowpath, the
page may be reused if everyone else has dropped their references.
This means that the necessary number of references is actually
`nc->size+1`.

Luckily, from a quick grep, it looks like the only path that can call
page_frag_alloc(fragsz=1) is TAP with the IFF_NAPI_FRAGS flag, which
requires CAP_NET_ADMIN in the init namespace and is only intended to be
used for kernel testing and fuzzing.

To test for this issue, put a `WARN_ON(page_ref_count(page) == 0)` in the
`offset < 0` path, below the virt_to_page() call, and then repeatedly call
writev() on a TAP device with IFF_TAP|IFF_NO_PI|IFF_NAPI_FRAGS|IFF_NAPI,
with a vector consisting of 15 elements containing 1 byte each.
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
net: phy: fix locking issue

Russell pointed out that the locking used in phy_is_started() isn't
needed and misleading. This locking also contributes to a race fixed
with patch 2.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Russell reported the following race in the phylib state machine
(quoting from his mail):

if (phy_polling_mode(phydev) && phy_is_started(phydev))
	phy_queue_state_machine(phydev, PHY_STATE_TIME);

state = PHY_UP
thread 0			thread 1
				phy_disconnect()
				+-phy_is_started()
phy_is_started()                |
				`-phy_stop()
				  +-phydev->state = PHY_HALTED
				  `-phy_stop_machine()
				    `-cancel_delayed_work_sync()
phy_queue_state_machine()
`-mod_delayed_work()

At this point, the phydev->state_queue() has been added back onto the
system workqueue despite phy_stop_machine() having been called and
cancel_delayed_work_sync() called on it.

Fix this by protecting the complete operation in thread 0.

Fixes: 2b3e88ea ("net: phy: improve phy state checking")
Reported-by: Russell King - ARM Linux admin <linux@armlinux.org.uk>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Russell suggested to remove the locking from phy_is_started() because
the read is atomic anyway and actually the locking may be more
misleading.

Fixes: 2b3e88ea ("net: phy: improve phy state checking")
Suggested-by: Russell King - ARM Linux admin <linux@armlinux.org.uk>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The clean target in the makefile conflicts with the generic
kselftests lib.mk, and fails to properly remove the compiled
test programs.

Remove the redundant rule, the TEST_GEN_FILES will be already
removed by the CLEAN macro in lib.mk.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Acked-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The value of ->num_ports comes from bcm_sf2_sw_probe() and it is less
than or equal to DSA_MAX_PORTS.  The ds->ports[] array is used inside
the dsa_is_user_port() and dsa_is_cpu_port() functions.  The ds->ports[]
array is allocated in dsa_switch_alloc() and it has ds->num_ports
elements so this leads to a static checker warning about a potential out
of bounds read.

Fixes: 8cfa9498 ("net: dsa: bcm_sf2: add suspend/resume callbacks")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With many active TCP sockets, fat TCP sockets could fool
__sk_mem_raise_allocated() thanks to an overflow.

They would increase their share of the memory, instead
of decreasing it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The GPIO interrupt controller on the espressobin board only supports edge interrupts.
If one enables the use of hardware interrupts in the device tree for the 88E6341, it is
possible to miss an edge.  When this happens, the INTn pin on the Marvell switch is
stuck low and no further interrupts occur.

I found after adding debug statements to mv88e6xxx_g1_irq_thread_work() that there is
a race in handling device interrupts (e.g. PHY link interrupts).  Some interrupts are
directly cleared by reading the Global 1 status register.  However, the device interrupt
flag, for example, is not cleared until all the unmasked SERDES and PHY ports are serviced.
This is done by reading the relevant SERDES and PHY status register.

The code only services interrupts whose status bit is set at the time of reading its status
register.  If an interrupt event occurs after its status is read and before all interrupts
are serviced, then this event will not be serviced and the INTn output pin will remain low.

This is not a problem with polling or level interrupts since the handler will be called
again to process the event.  However, it's a big problem when using level interrupts.

The fix presented here is to add a loop around the code servicing switch interrupts.  If
any pending interrupts remain after the current set has been handled, we loop and process
the new set.  If there are no pending interrupts after servicing, we are sure that INTn has
gone high and we will get an edge when a new event occurs.

Tested on espressobin board.

Fixes: dc30c35b ("net: dsa: mv88e6xxx: Implement interrupt support.")
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

phylib enables interrupts before phy_start() has been called, and if
we receive an interrupt in a non-started state, the interrupt handler
returns IRQ_NONE. This causes problems with at least one Marvell chip
as reported by Andrew.
Fix this by handling interrupts the same as in phy_mac_interrupt(),
basically always running the phylib state machine. It knows when it
has to do something and when not.
This change allows to handle interrupts gracefully even if they
occur in a non-started state.

Fixes: 2b3e88ea ("net: phy: improve phy state checking")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In sctp_stream_init(), after sctp_stream_outq_migrate() freed the
surplus streams' ext, but sctp_stream_alloc_out() returns -ENOMEM,
stream->outcnt will not be set to 'outcnt'.

With the bigger value on stream->outcnt, when closing the assoc and
freeing its streams, the ext of those surplus streams will be freed
again since those stream exts were not set to NULL after freeing in
sctp_stream_outq_migrate(). Then the invalid-free issue reported by
syzbot would be triggered.

We fix it by simply setting them to NULL after freeing.

Fixes: 5bbbbe32 ("sctp: introduce stream scheduler foundations")
Reported-by: syzbot+58e480e7b28f2d890bfd@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jianlin reported a panic when running sctp gso over gre over vlan device:

  [   84.772930] RIP: 0010:do_csum+0x6d/0x170
  [   84.790605] Call Trace:
  [   84.791054]  csum_partial+0xd/0x20
  [   84.791657]  gre_gso_segment+0x2c3/0x390
  [   84.792364]  inet_gso_segment+0x161/0x3e0
  [   84.793071]  skb_mac_gso_segment+0xb8/0x120
  [   84.793846]  __skb_gso_segment+0x7e/0x180
  [   84.794581]  validate_xmit_skb+0x141/0x2e0
  [   84.795297]  __dev_queue_xmit+0x258/0x8f0
  [   84.795949]  ? eth_header+0x26/0xc0
  [   84.796581]  ip_finish_output2+0x196/0x430
  [   84.797295]  ? skb_gso_validate_network_len+0x11/0x80
  [   84.798183]  ? ip_finish_output+0x169/0x270
  [   84.798875]  ip_output+0x6c/0xe0
  [   84.799413]  ? ip_append_data.part.50+0xc0/0xc0
  [   84.800145]  iptunnel_xmit+0x144/0x1c0
  [   84.800814]  ip_tunnel_xmit+0x62d/0x930 [ip_tunnel]
  [   84.801699]  gre_tap_xmit+0xac/0xf0 [ip_gre]
  [   84.802395]  dev_hard_start_xmit+0xa5/0x210
  [   84.803086]  sch_direct_xmit+0x14f/0x340
  [   84.803733]  __dev_queue_xmit+0x799/0x8f0
  [   84.804472]  ip_finish_output2+0x2e0/0x430
  [   84.805255]  ? skb_gso_validate_network_len+0x11/0x80
  [   84.806154]  ip_output+0x6c/0xe0
  [   84.806721]  ? ip_append_data.part.50+0xc0/0xc0
  [   84.807516]  sctp_packet_transmit+0x716/0xa10 [sctp]
  [   84.808337]  sctp_outq_flush+0xd7/0x880 [sctp]

It was caused by SKB_GSO_CB(skb)->csum_start not set in sctp_gso_segment.
sctp_gso_segment() calls skb_segment() with 'feature | NETIF_F_HW_CSUM',
which causes SKB_GSO_CB(skb)->csum_start not to be set in skb_segment().

For TCP/UDP, when feature supports HW_CSUM, CHECKSUM_PARTIAL will be set
and gso_reset_checksum will be called to set SKB_GSO_CB(skb)->csum_start.

So SCTP should do the same as TCP/UDP, to call gso_reset_checksum() when
computing checksum in sctp_gso_segment.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter/IPVS fixes for net

The following patchset contains Netfilter/IPVS fixes for net:

1) Missing structure initialization in ebtables causes splat with
   32-bit user level on a 64-bit kernel, from Francesco Ruggeri.

2) Missing dependency on nf_defrag in IPVS IPv6 codebase, from
   Andrea Claudi.

3) Fix possible use-after-free from release path of target extensions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox, mlx5 fixes 2019-02-13

This series introduces some fixes to mlx5 driver.
For more information please see tag log below.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently mlx5 driver creates xdp redirect hw queues unconditionally on
netdevice open, This is great until someone starts redirecting XDP traffic
via ndo_xdp_xmit on mlx5 device and changes the device configuration at
the same time, this might cause crashes, since the other device's napi
is not aware of the mlx5 state change (resources un-availability).

To fix this we must synchronize with other devices napi's on the system.
Added a new flag under mlx5e_priv to determine XDP TX resources are
available, set/clear it up when necessary and use synchronize_rcu()
when the flag is turned off, so other napi's are in-sync with it, before
we actually cleanup the hw resources.

The flag is tested prior to committing to transmit on mlx5e_xdp_xmit, and
it is sufficient to determine if it safe to transmit or not. The other
two internal flags (MLX5E_STATE_OPENED and MLX5E_SQ_STATE_ENABLED) become
unnecessary. Thus, they are removed from data path.

Fixes: 58b99ee3 ("net/mlx5e: Add support for XDP_REDIRECT in device-out side")
Reported-by: Toke Høiland-Jørgensen <toke@redhat.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Eliminate the following compilation warning:

drivers/net/ethernet/mellanox/mlx5/core/events.c: warning: 'error_str'
may be used uninitialized in this function [-Wuninitialized]:  => 238:3

Fixes: c2fb3db2 ("net/mlx5: Rework handling of port module events")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Mikhael Goikhman <migo@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When EEH is injected and PCI bus stalls, mlx5's pci error detect
function is called to deactivate the command interface and tear down
the device. The issue is that there can be a thread that already
passed MLX5_DEVICE_STATE_INTERNAL_ERROR check, it will send the command
and stuck in the wait_func.

Solution:
Add function mlx5_cmd_flush to disable command interface and clear all
the pending commands. When device state is set to
MLX5_DEVICE_STATE_INTERNAL_ERROR, call mlx5_cmd_flush to ensure all
pending threads waiting for firmware commands completion are terminated.

Fixes: c1d4d2e9 ("net/mlx5: Avoid calling sleeping function by the health poll thread")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

New channels are applied to the priv channels only after they
are successfully opened. Then, the indirection table should be built
according to the new number of channels.
Currently, such build is preformed independently of whether the
channels opening is successful, and is not reverted on failure.

The bug is caused due to removal of rss params from channels struct
and moving it to priv struct. That change cause to independency between
channels and rss params.
This causes a crash on a later point, when accessing rqn of a non
existing channel.

This patch fixes it by moving the indirection table build right before
switching the priv channels to new channels struct, after the new set of
channels was successfully opened.

Fixes: bbeb53b8 ("net/mlx5e: Move RSS params to a dedicated struct")
Signed-off-by: Maria Pasechnik <mariap@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Fetch pointer to module before target object is released.

Fixes: 29e38801 ("netfilter: nf_tables: fix use-after-free when deleting compat expressions")
Fixes: 0ca743a5 ("netfilter: nf_tables: add compatibility layer for x_tables")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

The current opt_inst_list operations inside team_nl_cmd_options_set()
is too complex to track:

    LIST_HEAD(opt_inst_list);
    nla_for_each_nested(...) {
        list_for_each_entry(opt_inst, &team->option_inst_list, list) {
            if (__team_option_inst_tmp_find(&opt_inst_list, opt_inst))
                continue;
            list_add(&opt_inst->tmp_list, &opt_inst_list);
        }
    }
    team_nl_send_event_options_get(team, &opt_inst_list);

as while we retrieve 'opt_inst' from team->option_inst_list, it could
be added to the local 'opt_inst_list' for multiple times. The
__team_option_inst_tmp_find() doesn't work, as the setter
team_mode_option_set() still calls team->ops.exit() which uses
->tmp_list too in __team_options_change_check().

Simplify the list operations by moving the 'opt_inst_list' and
team_nl_send_event_options_get() into the nla_for_each_nested() loop so
that it can be guranteed that we won't insert a same list entry for
multiple times. Therefore, __team_option_inst_tmp_find() can be removed
too.

Fixes: 4fb0534f ("team: avoid adding twice the same option to the event list")
Fixes: 2fcdb2c9 ("team: allow to send multiple set events in one message")
Reported-by: syzbot+4d4af685432dc0e56c91@syzkaller.appspotmail.com
Reported-by: syzbot+68ee510075cf64260cc4@syzkaller.appspotmail.com
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cong Wang says:

====================
net_sched: some fixes for cls_tcindex

This patchset contains 3 bug fixes for tcindex filter. Please check
each patch for details.

v2: fix a compile error in patch 2
    drop netns refcnt in patch 1
====================
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>

struct tcindex_filter_result contains two parts:
struct tcf_exts and struct tcf_result.

For the local variable 'cr', its exts part is never used but
initialized without being released properly on success path. So
just completely remove the exts part to fix this leak.

For the local variable 'new_filter_result', it is never properly
released if not used by 'r' on success path.

Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When tcindex_destroy() destroys all the filter results in
the perfect hash table, it invokes the walker to delete
each of them. However, results with class==0 are skipped
in either tcindex_walk() or tcindex_delete(), which causes
a memory leak reported by kmemleak.

This patch fixes it by skipping the walker and directly
deleting these filter results so we don't miss any filter
result.

As a result of this change, we have to initialize exts->net
properly in tcindex_alloc_perfect_hash(). For net-next, we
need to consider whether we should initialize ->net in
tcf_exts_init() instead, before that just directly test
CONFIG_NET_CLS_ACT=y.

Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcindex_destroy() invokes tcindex_destroy_element() via
a walker to delete each filter result in its perfect hash
table, and tcindex_destroy_element() calls tcindex_delete()
which schedules tcf RCU works to do the final deletion work.
Unfortunately this races with the RCU callback
__tcindex_destroy(), which could lead to use-after-free as
reported by Adrian.

Fix this by migrating this RCU callback to tcf RCU work too,
as that workqueue is ordered, we will not have use-after-free.

Note, we don't need to hold netns refcnt because we don't call
tcf_exts_destroy() here.

Fixes: 27ce4f05 ("net_sched: use tcf_queue_work() in tcindex filter")
Reported-by: Adrian <bugs@abtelecom.ro>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Arthur Kiyanovski says:

====================
net: ena: race condition bug fix and version update

This patchset includes a fix to a race condition that can cause
kernel panic, as well as a driver version update because of this
fix.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Update driver version due to bug fix.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix race condition between ena_update_on_link_change() and
ena_restore_device().

This race can occur if link notification arrives while the driver
is performing a reset sequence. In this case link can be set up,
enabling the device, before it is fully restored. If packets are
sent at this time, the driver might access uninitialized data
structures, causing kernel crash.

Move the clearing of ENA_FLAG_ONGOING_RESET and netif_carrier_on()
after ena_up() to ensure the device is ready when link is set up.

Fixes: d18e4f68 ("net: ena: fix race condition between device reset and link up setup")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When calculating rb->frames_per_block * req->tp_block_nr the result
can overflow. Check it for overflow without limiting the total buffer
size to UINT_MAX.

This change fixes support for packet ring buffers >= UINT_MAX.

Fixes: 8f8d28e4 ("net/packet: fix overflow in check for tp_frame_nr")
Signed-off-by: Kal Conley <kal.conley@dectris.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Field idiag_ext in struct inet_diag_req_v2 used as bitmap of requested
extensions has only 8 bits. Thus extensions starting from DCTCPINFO
cannot be requested directly. Some of them included into response
unconditionally or hook into some of lower 8 bits.

Extension INET_DIAG_CLASS_ID has not way to request from the beginning.

This patch bundle it with INET_DIAG_TCLASS (ipv6 tos), fixes space
reservation, and documents behavior for other extensions.

Also this patch adds fallback to reporting socket priority. This filed
is more widely used for traffic classification because ipv4 sockets
automatically maps TOS to priority and default qdisc pfifo_fast knows
about that. But priority could be changed via setsockopt SO_PRIORITY so
INET_DIAG_TOS isn't enough for predicting class.

Also cgroup2 obsoletes net_cls classid (it always zero), but we cannot
reuse this field for reporting cgroup2 id because it is 64-bit (ino+gen).

So, after this patch INET_DIAG_CLASS_ID will report socket priority
for most common setup when net_cls isn't set and/or cgroup2 in use.

Fixes: 0888e372 ("net: inet: diag: expose sockets cgroup classid")
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

KMSAN reported batadv_interface_tx() was possibly using a
garbage value [1]

batadv_get_vid() does have a pskb_may_pull() call
but batadv_interface_tx() does not actually make sure
this did not fail.

[1]
BUG: KMSAN: uninit-value in batadv_interface_tx+0x908/0x1e40 net/batman-adv/soft-interface.c:231
CPU: 0 PID: 10006 Comm: syz-executor469 Not tainted 4.20.0-rc7+ #5
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x173/0x1d0 lib/dump_stack.c:113
 kmsan_report+0x12e/0x2a0 mm/kmsan/kmsan.c:613
 __msan_warning+0x82/0xf0 mm/kmsan/kmsan_instr.c:313
 batadv_interface_tx+0x908/0x1e40 net/batman-adv/soft-interface.c:231
 __netdev_start_xmit include/linux/netdevice.h:4356 [inline]
 netdev_start_xmit include/linux/netdevice.h:4365 [inline]
 xmit_one net/core/dev.c:3257 [inline]
 dev_hard_start_xmit+0x607/0xc40 net/core/dev.c:3273
 __dev_queue_xmit+0x2e42/0x3bc0 net/core/dev.c:3843
 dev_queue_xmit+0x4b/0x60 net/core/dev.c:3876
 packet_snd net/packet/af_packet.c:2928 [inline]
 packet_sendmsg+0x8306/0x8f30 net/packet/af_packet.c:2953
 sock_sendmsg_nosec net/socket.c:621 [inline]
 sock_sendmsg net/socket.c:631 [inline]
 __sys_sendto+0x8c4/0xac0 net/socket.c:1788
 __do_sys_sendto net/socket.c:1800 [inline]
 __se_sys_sendto+0x107/0x130 net/socket.c:1796
 __x64_sys_sendto+0x6e/0x90 net/socket.c:1796
 do_syscall_64+0xbc/0xf0 arch/x86/entry/common.c:291
 entry_SYSCALL_64_after_hwframe+0x63/0xe7
RIP: 0033:0x441889
Code: 18 89 d0 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 bb 10 fc ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007ffdda6fd468 EFLAGS: 00000216 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 0000000000000002 RCX: 0000000000441889
RDX: 000000000000000e RSI: 00000000200000c0 RDI: 0000000000000003
RBP: 0000000000000003 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000216 R12: 00007ffdda6fd4c0
R13: 00007ffdda6fd4b0 R14: 0000000000000000 R15: 0000000000000000

Uninit was created at:
 kmsan_save_stack_with_flags mm/kmsan/kmsan.c:204 [inline]
 kmsan_internal_poison_shadow+0x92/0x150 mm/kmsan/kmsan.c:158
 kmsan_kmalloc+0xa6/0x130 mm/kmsan/kmsan_hooks.c:176
 kmsan_slab_alloc+0xe/0x10 mm/kmsan/kmsan_hooks.c:185
 slab_post_alloc_hook mm/slab.h:446 [inline]
 slab_alloc_node mm/slub.c:2759 [inline]
 __kmalloc_node_track_caller+0xe18/0x1030 mm/slub.c:4383
 __kmalloc_reserve net/core/skbuff.c:137 [inline]
 __alloc_skb+0x309/0xa20 net/core/skbuff.c:205
 alloc_skb include/linux/skbuff.h:998 [inline]
 alloc_skb_with_frags+0x1c7/0xac0 net/core/skbuff.c:5220
 sock_alloc_send_pskb+0xafd/0x10e0 net/core/sock.c:2083
 packet_alloc_skb net/packet/af_packet.c:2781 [inline]
 packet_snd net/packet/af_packet.c:2872 [inline]
 packet_sendmsg+0x661a/0x8f30 net/packet/af_packet.c:2953
 sock_sendmsg_nosec net/socket.c:621 [inline]
 sock_sendmsg net/socket.c:631 [inline]
 __sys_sendto+0x8c4/0xac0 net/socket.c:1788
 __do_sys_sendto net/socket.c:1800 [inline]
 __se_sys_sendto+0x107/0x130 net/socket.c:1796
 __x64_sys_sendto+0x6e/0x90 net/socket.c:1796
 do_syscall_64+0xbc/0xf0 arch/x86/entry/common.c:291
 entry_SYSCALL_64_after_hwframe+0x63/0xe7

Fixes: c6c8fea2 ("net: Add batman-adv meshing protocol")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc:	Marek Lindner <mareklindner@neomailbox.ch>
Cc:	Simon Wunderlich <sw@simonwunderlich.de>
Cc:	Antonio Quartulli <a@unstable.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

genlmsg_reply can fail, so propagate its return code

Fixes: 915d7e5e ("ipv6: sr: add code base for control plane support of SR-IPv6")
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When an ethernet frame is padded to meet the minimum ethernet frame
size, the padding octets are not covered by the hardware checksum.
Fortunately the padding octets are usually zero's, which don't affect
checksum. However, it is not guaranteed. For example, switches might
choose to make other use of these octets.
This repeatedly causes kernel hardware checksum fault.

Prior to the cited commit below, skb checksum was forced to be
CHECKSUM_NONE when padding is detected. After it, we need to keep
skb->csum updated. However, fixing up CHECKSUM_COMPLETE requires to
verify and parse IP headers, it does not worth the effort as the packets
are so small that CHECKSUM_COMPLETE has no significant advantage.

Future work: when reporting checksum complete is not an option for
IP non-TCP/UDP packets, we can actually fallback to report checksum
unnecessary, by looking at cqe IPOK bit.

Fixes: 88078d98 ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends")
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

During testing on Armada 388 platforms, it was found with a certain
module configuration that it was possible to trigger a kernel oops
during the module load process, caused by the phylink resolver being
triggered for a currently disabled interface.

This problem was introduced by changing the way the SFP registration
works, which now can result in the sfp link down notification being
called during phylink_create().

Fixes: b5bfc21a ("net: sfp: do not probe SFP module before we're attached")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Due to the depends on NET_UDP_TUNNEL, at the moment it is impossible to
compile GENEVE if no other protocol depending on NET_UDP_TUNNEL is
selected.

Fix this changing the depends to a select, and drop NET_IP_TUNNEL from the
select list, as it already depends on NET_UDP_TUNNEL.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Reviewed-and-tested-by: Andrea Claudi <aclaudi@redhat.com>
Tested-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bitmap of found partitions in efx_ef10_mtd_probe was not
initialised, causing partitions to be suppressed based off whatever
value was in the bitmap at the start.

Fixes: 33664635 ("sfc: suppress duplicate nvmem partition types in efx_ef10_mtd_probe")
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2019-02-12' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
Just a few fixes:
 * aggregation session teardown with internal TXQs was
   continuing to send some frames marked as aggregation,
   fix from Ilan
 * IBSS join was missed during firmware restart, should
   such a thing happen
 * speculative execution based on the return value of
   cfg80211_classify8021d() - which is controlled by the
   sender of the packet - could be problematic in some
   code using it, prevent it
 * a few peer measurement fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>