Describe the PHY topology for all configurations supported by each board

Based on prior work by Andy Fleming <afleming@freescale.com>
Signed-off-by: Shruti Kanetkar <Shruti@freescale.com>
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Igal Liberman <Igal.Liberman@freescale.com>
Signed-off-by: Scott Wood <oss@buserror.net>

Signed-off-by: Alessio Igor Bogani <alessio.bogani@elettra.eu>
Signed-off-by: Scott Wood <oss@buserror.net>

Avoid duplication of the interrupt-parent, migrate to 4 interrupt-cells
and set the right clock-frequency for pcie (100 Mhz).
Signed-off-by: Alessio Igor Bogani <alessio.bogani@elettra.eu>
Signed-off-by: Scott Wood <oss@buserror.net>

Signed-off-by: Alessio Igor Bogani <alessio.bogani@elettra.eu>
Signed-off-by: Scott Wood <oss@buserror.net>

Signed-off-by: Alessio Igor Bogani <alessio.bogani@elettra.eu>
Signed-off-by: Scott Wood <oss@buserror.net>

This patch show how defconfigs appear if the kconfig fragment approach is
used.
Signed-off-by: Alessio Igor Bogani <alessio.bogani@elettra.eu>
Signed-off-by: Scott Wood <oss@buserror.net>

Signed-off-by: Alessio Igor Bogani <alessio.bogani@elettra.eu>
Signed-off-by: Scott Wood <oss@buserror.net>

Remove one instruction in mulhdu
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>

Inlining of _dcache_range() functions has shown that the compiler
does the same thing a bit better with one insn less
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>

This simplification helps the compiler. We now have only one test
instead of two, so it reduces the number of branches.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>

flush/clean/invalidate _dcache_range() functions are all very
similar and are quite short. They are mainly used in __dma_sync()
perf_event locate them in the top 3 consumming functions during
heavy ethernet activity

They are good candidate for inlining, as __dma_sync() does
almost nothing but calling them
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>

clear_pages() is never used expect by clear_page, and PPC32 is the
only architecture (still) having this function. Neither PPC64 nor
any other architecture has it.

This patch removes clear_pages() and moves clear_page() function
inline (same as PPC64) as it only is a few isns
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>

This patch adds inline functions to use dcbz, dcbi, dcbf, dcbst
from C functions
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>

On PPC8xx, flushing instruction cache is performed by writing
in register SPRN_IC_CST. This registers suffers CPU6 ERRATA.
The patch rewrites the fonction in C so that CPU6 ERRATA will
be handled transparently
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>

There is no real need to have set_context() in assembly.
Now that we have mtspr() handling CPU6 ERRATA directly, we
can rewrite set_context() in C language for easier maintenance.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>

CPU6 ERRATA is now handled directly in mtspr(), so we can use the
standard set_dec() fonction in all cases.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>

MPC8xx has an ERRATA on the use of mtspr() for some registers
This patch includes the ERRATA handling directly into mtspr() macro
so that mtspr() users don't need to bother about that errata
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>

Add missing SPRN defines into reg_8xx.h
Some of them are defined in mmu-8xx.h, so we include mmu-8xx.h in
reg_8xx.h, for that we remove references to PAGE_SHIFT in mmu-8xx.h
to have it self sufficient, as includers of reg_8xx.h don't all
include asm/page.h
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>

ioremap_base is not initialised and is nowhere used so remove it
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>

Commit 77116849 ("[POWERPC] Remove unused machine call outs")
removed the call to setup_io_mappings(), so remove the associated
progress line message
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>

x_mapped_by_bats() and x_mapped_by_tlbcam() serve the same kind of
purpose, and are never defined at the same time.
So rename them x_block_mapped() and define them in the relevant
places
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>

The fixmap related functions try to map kernel pages that are
already mapped through Large TLBs. pte_offset_kernel() has to
return NULL for LTLBs, otherwise the caller will try to access
level 2 table which doesn't exist
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>

Now we have a 8xx specific .c file for that so put it in there
as other powerpc variants do
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>

Now the noltlbs kernel parameter is also applicable to PPC8xx
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>

On a live running system (VoIP gateway for Air Trafic Control), over
a 10 minutes period (with 277s idle), we get 87 millions DTLB misses
and approximatly 35 secondes are spent in DTLB handler.
This represents 5.8% of the overall time and even 10.8% of the
non-idle time.
Among those 87 millions DTLB misses, 15% are on user addresses and
85% are on kernel addresses. And within the kernel addresses, 93%
are on addresses from the linear address space and only 7% are on
addresses from the virtual address space.

MPC8xx has no BATs but it has 8Mb page size. This patch implements
mapping of kernel RAM using 8Mb pages, on the same model as what is
done on the 40x.

In 4k pages mode, each PGD entry maps a 4Mb area: we map every two
entries to the same 8Mb physical page. In each second entry, we add
4Mb to the page physical address to ease life of the FixupDAR
routine. This is just ignored by HW.

In 16k pages mode, each PGD entry maps a 64Mb area: each PGD entry
will point to the first page of the area. The DTLB handler adds
the 3 bits from EPN to map the correct page.

With this patch applied, we now get only 13 millions TLB misses
during the 10 minutes period. The idle time has increased to 313s
and the overall time spent in DTLB miss handler is 6.3s, which
represents 1% of the overall time and 2.2% of non-idle time.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>

We are spending between 40 and 160 cycles with a mean of 65 cycles in
the DTLB handling routine (measured with mftbl) so make it more
simple althought it adds one instruction.
With this modification, we get three registers available at all time,
which will help with following patch.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>

add the missing RAID Engine device node for p5040.
otherwise, the device can not be detected.
Signed-off-by: Xuelin Shi <xuelin.shi@nxp.com>
Signed-off-by: Scott Wood <oss@buserror.net>

csum_partial is often called for small fixed length packets
for which it is suboptimal to use the generic csum_partial()
function.

For instance, in my configuration, I got:
* One place calling it with constant len 4
* Seven places calling it with constant len 8
* Three places calling it with constant len 14
* One place calling it with constant len 20
* One place calling it with constant len 24
* One place calling it with constant len 32

This patch renames csum_partial() to __csum_partial() and
implements csum_partial() as a wrapper inline function which
* uses csum_add() for small 16bits multiple constant length
* uses ip_fast_csum() for other 32bits multiple constant
* uses __csum_partial() in all other cases
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>

Modify platform driver suspend/resume to syscore
suspend/resume. This is because p1022ds needs to use
localbus when entering the PCIE resume.
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
[scottwood: dropped makefile churn]
Signed-off-by: Scott Wood <oss@buserror.net>

When CONFIG_DEBUG_PAGEALLOC is activated, the initial TLB mapping gets
flushed to track accesses to wrong areas. Therefore, kernel addresses
will also generate ITLB misses.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>

The MPC885 reference manual says that SDCR shall have value 0x40, but
most exemples set SDCR to 0x1
With 0x1 in SDCR, we observe TX underruns on SCC when using it in
QMC mode.
According the NXP technical support, this is a copy/paste error from
MPC860 reference manual, 0x40 being the only value supported
by the MPC885 HW.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>

This patch disables deprecated IDE subsystem in mpc8610_hpcd_defconfig
(no IDE host drivers are selected in this config so there is no valid
reason to enable IDE subsystem itself).
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Scott Wood <oss@buserror.net>

This patch disables deprecated IDE subsystem in stx_gp3_defconfig
(no IDE host drivers are selected in this config so there is no valid
reason to enable IDE subsystem itself).

Cc: Scott Wood <oss@buserror.net>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Scott Wood <oss@buserror.net>

This patch disables deprecated IDE subsystem in ksi8560_defconfig
(no IDE host drivers are selected in this config so there is no valid
reason to enable IDE subsystem itself).

Cc: Scott Wood <oss@buserror.net>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Scott Wood <oss@buserror.net>

This patch disables deprecated IDE subsystem in mpc834x_itx_defconfig
(no IDE host drivers are selected in this config so there is no valid
reason to enable IDE subsystem itself).

Cc: Scott Wood <oss@buserror.net>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Scott Wood <oss@buserror.net>

cpm_muram_alloc_common is called twice and both the times
spin_lock_irqsave is held.
Using GFP_KERNEL can sleep in spin_lock_irqsave context and cause
deadlock
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: Scott Wood <oss@buserror.net>

as cpm_muram_alloc_common is used only in this file,
making it static
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: Scott Wood <oss@buserror.net>

127 is the theoretical up boundary of QEIC number,
in fact there only be 44 qe_ic_info now.
add check to overflow for qe_ic_info
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Scott Wood <oss@buserror.net>

The FMan contains internal PHY devices used for SGMII connections
to external PHYs. When these PHYs are in use a reference is needed
for both the external PHY and the internal one. For the external
PHY phy-handle provides the reference. For the internal PHY a new
handle is required.
In dTSEC, the internal PHY is a TBI (Ten Bit Interface) PHY,
the handle used will be tbi-handle.
In mEMAC, the internal PHY is a PCS (Physical Coding Sublayer) PHY,
the handle used will be pcsphy-handle.
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Signed-off-by: Scott Wood <oss@buserror.net>

Support Freescale E6500 core-based platforms, like t4240.
Support disabling/enabling individual CPU thread dynamically.
Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>