- 23 Sep, 2014 4 commits
-
-
Matthias Schwarzott authored
Add support for: [2040:b139] Hauppauge WinTV HVR-901H (1114xx) According to the inf file, the hardware is similar to [2040:b131] Hauppauge WinTV 930C-HD (model 1114xx) The only difference is the demod Si2161 instead of Si2165 (but both are supported by the si2165 driver). Signed-off-by:
Matthias Schwarzott <zzam@gentoo.org> Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-
Matthias Schwarzott authored
Add support for: [2040:b138] Hauppauge WinTV HVR-900H (111xxx) The hardware is similar to [2040:b130] Hauppauge WinTV 930C-HD (model 1113xx) The only difference is the demod Si2161 instead of Si2165 (but both are supported by the si2165 driver). Signed-off-by:
-
Matthias Schwarzott authored
Additionally print chip name with revision symbolically. This is a preparation for supporting new Hauppauge WinTV-HVR-900-H based on cx231xx. Signed-off-by:
-
Matthias Schwarzott authored
Current firmware is only for revision D. Signed-off-by:
-
- 22 Sep, 2014 17 commits
-
-
Jingoo Han authored
Casting the return value which is a void pointer is redundant. The conversion from void pointer to any other pointer type is guaranteed by the C programming language. Signed-off-by:
Jingoo Han <jg1.han@samsung.com> Signed-off-by:
-
Fengguang Wu authored
make vpfe_standards[] static. Signed-off-by:
Fengguang Wu <fengguang.wu@intel.com> Signed-off-by:
-
Olli Salonen authored
Add a maintainer for the new CIMaX SP2 driver. Signed-off-by:
Olli Salonen <olli.salonen@iki.fi> Signed-off-by:
-
Mauro Carvalho Chehab authored
A simplified version of the semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @decl@ identifier i1,fld; type T; field list[n] fs; @@ struct i1 { fs T fld; ...}; @bad@ identifier decl.i1,i2; expression e; initializer list[decl.n] is; @@ struct i1 i2 = { is, + .fld = e - e ,...}; // </smpl> Not sure why, but some tables are still using the old way, but at least several of them got fixed. Signed-off-by:
-
Julia Lawall authored
Use c99 initializers for structures. A simplified version of the semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @decl@ identifier i1,fld; type T; field list[n] fs; @@ struct i1 { fs T fld; ...}; @bad@ identifier decl.i1,i2; expression e; initializer list[decl.n] is; @@ struct i1 i2 = { is, + .fld = e - e ,...}; // </smpl> Signed-off-by:
Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by:
-
Mauro Carvalho Chehab authored
This is used by the I2C code in order to slow down the speed to 20 kHz on devices with xc5000 or xc5000c. So, it needs to be filled for all devices that use either xc5000 or xc5000c. Signed-off-by: -
Mauro Carvalho Chehab authored
Right now, the au0828 driver uses .tuner to detect if analog tv is being used or not. By not filling .tuner fields at the board struct, the I2C core can't do decisions based on it. So, add a field to explicitly tell when analog TV is supported. No functional changes. Signed-off-by: -
Mauro Carvalho Chehab authored
This comment is already at the au0828-i2c where it belongs. So, remove it from a board's entry. It doesn't make any sense there, as we're setting the clock to 250kHz there, slowing it down only at the au0828-i2c. Signed-off-by: -
Mauro Carvalho Chehab authored
cab_state->modulation is initialized with a wrong value: drivers/media/dvb-frontends/stv0367.c:3000:42: warning: mixing different enum types drivers/media/dvb-frontends/stv0367.c:3000:42: int enum fe_modulation versus drivers/media/dvb-frontends/stv0367.c:3000:42: int enum stv0367cab_mod as it was declared as "enum stv0367cab_mod". While it could be fixed, there's no value on it, as this is never used. So, just remove the modulation from cab_state structure. Signed-off-by: -
Maks Naumov authored
It was using the wrong constant for QAM256 on get_frontend. Signed-off-by:
Maks Naumov <maksqwe1@ukr.net> Signed-off-by:
-
Frank Schaefer authored
Instead of using a temporary stack allocated i2c_client in em28xx_i2c_ir_handle_key(), allocate/free the i2c_client at module init/uninit and hook it into struct em28xx_IR (if the device has an i2c IR decoder). This reduces the frame size of function em28xx_i2c_ir_handle_key() and speeds it up a bit. Also make sure that all fields of struct i2c_client are initialized properly. Signed-off-by:
Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by:
-
Himangi Saraogi authored
This patch introduces the use of !usb_endpoint_dir_in(epd) and !usb_endpoint_xfer_int(epd). The Coccinelle semantic patch that makes these changes is as follows: - ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) != - \(USB_DIR_IN\|0x80\)) + !usb_endpoint_dir_in(epd) @@ struct usb_endpoint_descriptor *epd; @@ - ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) != - \(USB_ENDPOINT_XFER_INT\|3\)) + !usb_endpoint_xfer_int(epd) Signed-off-by:
Himangi Saraogi <himangi774@gmail.com> Acked-by:
-
Himangi Saraogi authored
This patch introduces the use of the function usb_endpoint_type. The Coccinelle semantic patch that makes these changes is as follows: @@ struct usb_endpoint_descriptor *epd; @@ - (epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) + usb_endpoint_type(epd) Signed-off-by:
-
Hans Wennborg authored
Just returns whatever error that was returned by the i2c core, in the case of errors, only returning -EREMOTEIO if the transfer size is not what it was expected. Signed-off-by:
Hans Wennborg <hans@hanshq.net> Signed-off-by:
-
Hans Wennborg authored
The returned code is 0, 1 or an error. It doesn't make sense to print it in hexadecimal. Signed-off-by:
-
Andrey Utkin authored
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=81621Reported-by:
David Binderman <dcb314@hotmail.com> Signed-off-by:
Andrey Utkin <andrey.krieger.utkin@gmail.com> Signed-off-by:
-
Mauro Carvalho Chehab authored
There are two modprobe parameters for VBI that aren't used anywhere (one for debug, the other one related to the buffer size). Get rid of them! Signed-off-by:
-
- 21 Sep, 2014 19 commits
-
-
Morgan Phillips authored
Signed-off-by:
Morgan Phillips <winter2718@gmail.com> Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Morgan Phillips authored
Signed-off-by:
-
Hans Verkuil authored
The norm_swidth function was unused and is dropped. It's not clear what the purpose of that function was. The norm_maxh function was changed so it tests for 60 Hz standards rather than for 50 Hz standards. The is the preferred order. The norm_maxw function was poorly written and used: it gives the maximum allowed line width for the given standard. For 60 Hz that's 720, but for 50 Hz that's 768 which allows for 768x576 which gives you square pixels. For 60 Hz formats it is 640x480 that gives square pixels, so there is no need to go beyond 720. The initial width was set using norm_maxh(), which was wrong. Just set to 720, that's what you normally use. Since the initial standard was NTSC anyway the initial width was always 720 anyway. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
-
Hans Verkuil authored
Tested VBI support and discovered that the wrong offset was used. After this change it is now working. Verified with CC/XDS for NTSC and WSS/Teletext on PAL. It also reported the wrong start lines for the second field. That's now fixed as well. Signed-off-by:
-
Hans Verkuil authored
Both adv7604 and adv7842 had the same typo in the code that sets the vertical backporch for the second interlaced field: it was assigned to vbackporch instead of il_vbackporch. In addition, the timings struct wasn't zeroed in the adv7842 driver, leaving several fields to undefined values causing the timing match function to fail. Signed-off-by:
-
Hans Verkuil authored
If one or both of the timings being compared have the standards field with value 0, then accept that. Only check for matching standards if both timings have actually filled in that field. Otherwise no match will ever be found since when timings are detected the standards field will typically be set to 0 by the driver. Signed-off-by:
-
Hans Verkuil authored
This is useful to test teletext capture applications like alevt and mtt. It also fixes a previously undetected bug where the PAL VBI start line of the second field was off by one. Using the new field start defines helps a lot fixing such bugs. Signed-off-by:
-
Hans Verkuil authored
G_EDID is an RW ioctl, so the struct v4l2_edid isn't const. Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
-
Guennadi Liakhovetski authored
A test in uvc_video_decode_isoc() checks whether an image has been received from the camera completely. For this the data amount is compared to the buffer length, which, however, doesn't have to be equal to the image size. Switch to using formats .sizeimage field for an exact expected image size. [Renamed image_size to frame_size] Signed-off-by:
Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Mauro Carvalho Chehab authored
drivers/media/usb/hackrf/hackrf.c:64:3: warning: this decimal constant is unsigned only in ISO C90 [enabled by default] .rangehigh = 4294967294, /* max u32, hw goes over 7GHz */ ^ Signed-off-by: -
Antti Palosaari authored
HackRF SDR driver. Video4Linux USB device. Signed-off-by:
Antti Palosaari <crope@iki.fi> Signed-off-by:
-
Antti Palosaari authored
V4L2 driver for HackRF SDR. Very basic version, with reduced feature set. Driver implements receiver only, hardware supports also transmitter. USB ID 1d50:6089. Model HackRF One Signed-off-by:
-
Laurent Pinchart authored
The ARGB32 pixel format's fourcc value is defined to 'BA24' in the videodev2.h header, but documented as 'AX24'. Fix the documentation. Reported-by:
-
Laurent Pinchart authored
The existing RGB555X pixel format is ill-defined in respect to its alpha bit and its meaning is driver dependent. Create new standard ARGB555X and XRGB555X variants with clearly defined meanings and make the existing variant deprecated. The new pixel formats 4CC values have been selected to match the DRM 4CCs for the same in-memory formats. Signed-off-by:
-
Laurent Pinchart authored
Replace strncpy + manually setting the terminating '\0' with an strlcpy call. Reported-by:
Joe Perches <joe@perches.com> Signed-off-by:
-
Paul Fertser authored
As reported on [1], this device needs this quirk to be able to reliably initialise the webcam. [1] http://ubuntuforums.org/showthread.php?t=2145996 Cc: stable@vger.kernel.org Signed-off-by:
Paul Fertser <fercerpav@gmail.com> Signed-off-by:
-
William Manley authored
The uvcvideo webcam driver exposes the v4l2 control "Exposure (Absolute)" which allows the user to control the exposure time of the webcam, essentially controlling the brightness of the received image. By default the webcam automatically adjusts the exposure time automatically but the if you set the control "Exposure, Auto"="Manual Mode" the user can fix the exposure time. Unfortunately it seems that the Logitech C920 has a firmware bug where it will forget that it's in manual mode temporarily during initialisation. This means that the camera doesn't respect the exposure time that the user requested if they request it before starting to stream video. They end up with a video stream which is either too bright or too dark and must reset the controls after video starts streaming. This patch introduces the quirk UVC_QUIRK_RESTORE_CTRLS_ON_INIT which causes the cached controls to be re-uploaded to the camera immediately after initialising the camera. This quirk is applied to the C920 to work around this camera bug. Signed-off-by:
William Manley <will@williammanley.net> Signed-off-by:
-
Vincent Palatin authored
Map V4L2_CID_TILT_SPEED and V4L2_CID_PAN_SPEED to the standard UVC CT_PANTILT_RELATIVE_CONTROL terminal control request. Tested by plugging a Logitech ConferenceCam C3000e USB camera and controlling pan/tilt from the userspace using the VIDIOC_S_CTRL ioctl. Verified that it can pan and tilt at the same time in both directions. Signed-off-by:
Vincent Palatin <vpalatin@chromium.org> Reviewed-by:
Pawel Osciak <posciak@chromium.org> Signed-off-by:
-
Vincent Palatin authored
The V4L2_CID_PAN_SPEED and V4L2_CID_TILT_SPEED controls allow to move the camera by setting its rotation speed around its axis. Signed-off-by:
-
