Currently, the filter's protocol is ignored except for a few special
cases (IPv4 and IPv6).

The EtherType can be matched inside VCAP IS2 by using a MAC_ETYPE key.
So there are 2 cases in which EtherType matches are supported:

  - As part of a larger MAC_ETYPE rule, such as:

    tc filter add dev swp0 ingress protocol ip \
            flower skip_sw src_mac 42:be:24:9b:76:20 action drop

  - Standalone (matching on protocol only):

    tc filter add dev swp0 ingress protocol arp \
            flower skip_sw action drop

As before, if the protocol is not specified, is it implicitly "all" and
the EtherType mask in the MAC_ETYPE half key is set to zero.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yangbo Lu says:

====================
Support programmable pins for Ocelot PTP driver

The Ocelot PTP clock driver had been embedded into ocelot.c driver.
It had supported basic gettime64/settime64/adjtime/adjfine functions
by now which were used by both Ocelot switch and Felix switch.

This patch-set is to move current ptp clock code out of ocelot.c driver
maintaining as a single ocelot_ptp.c driver, and to implement 4
programmable pins with only PTP_PF_PEROUT function for now.
The PTP_PF_EXTTS function will be supported in the future, and it should
be implemented separately for Felix and Ocelot, because of different
hardware interrupt implementation in them.

Changes for v2:
	- Put PTP driver under drivers/net/ethernet/mscc/.
	- Dropped MAINTAINERS patch. Kept original maintaining.
	- Initialized PTP separately in ocelot/felix platforms.
	- Supported PPS case in programmable pin.
	- Supported disabling pin function since deadlock is fixed by Richard.
	- Returned -EBUSY if not finding pin available.
Changes for v3:
	- Re-sent.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable PTP programmable pin.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable PTP programmable pin.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Support 4 PTP programmable pins with only PTP_PF_PEROUT function
for now. The PTP_PF_EXTTS function will be supported in the
future, and it should be implemented separately for Felix and
Ocelot, because of different hardware interrupt implementation
in them.

Since the hardware is not able to support absolute start time,
the periodic clock request only allows start time 0 0. But nsec
could be accepted for PPS case for phase adjustment.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add wave programming registers definitions for Ocelot platforms.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are 5 PTP_PINS register groups on Ocelot switch.
Except the one used for TOD operations, there are still
4 register groups for programmable pins. So redefine the
4 programmable pins.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The timestamp info should be only software timestamp capabilities
if ptp clock does not work.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Ocelot PTP clock driver had been embedded into ocelot.c driver.
It had supported basic gettime64/settime64/adjtime/adjfine functions
by now which were used by both Ocelot switch and Felix switch.

This patch is to move current ptp clock code out of ocelot.c driver
maintaining as a single ocelot_ptp.c.
For futher new features implementation, the common code could be put
in ocelot_ptp.c and the switch specific code should be in specific
switch driver. The interrupt implementation in SoC is different
between Ocelot and Felix.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Leon Romanovsky says:

====================
Remove vermagic header from global include folder

Changelog:
v2:
 * Changed the implementation of patch #4 to be like Masahiro wants.
I personally don't like this implementation and changing it just to move forward
this this patchset.
v1:
https://lore.kernel.org/lkml/20200415133648.1306956-1-leon@kernel.org
 * Added tags
 * Updated patch #4 with test results
 * Changed scripts/mod/modpost.c to create inclusion of vermagic.h
   from kernel folder and not from general include/linux. This is
   needed to generate *.mod.c files, while building modules.
v0:
https://lore.kernel.org/lkml/20200414155732.1236944-1-leon@kernel.org

This is followup to the failure reported by Borislav [1] and suggested
fix later on [2].

The series removes all includes of linux/vermagic.h, updates hns and
nfp to use same kernel versioning scheme (exactly like we did for
other drivers in previous cycle) and removes vermagic.h from global
include folder.

[1] https://lore.kernel.org/lkml/20200411155623.GA22175@zn.tnic
[2] https://lore.kernel.org/lkml/20200413080452.GA3772@zn.tnic
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

VERMAGIC* definitions are not supposed to be used by the drivers,
see this [1] bug report, so introduce special define to guard inclusion
of this header file and define it in kernel/modules.h and in internal
script that generates *.mod.c files.

In-tree module build:
➜  kernel git:(vermagic) ✗ make clean
➜  kernel git:(vermagic) ✗ make M=drivers/infiniband/hw/mlx5
➜  kernel git:(vermagic) ✗ modinfo drivers/infiniband/hw/mlx5/mlx5_ib.ko
filename:	/images/leonro/src/kernel/drivers/infiniband/hw/mlx5/mlx5_ib.ko
<...>
vermagic:       5.6.0+ SMP mod_unload modversions

Out-of-tree module build:
➜  mlx5 make -C /images/leonro/src/kernel clean M=/tmp/mlx5
➜  mlx5 make -C /images/leonro/src/kernel M=/tmp/mlx5
➜  mlx5 modinfo /tmp/mlx5/mlx5_ib.ko
filename:       /tmp/mlx5/mlx5_ib.ko
<...>
vermagic:       5.6.0+ SMP mod_unload modversions

[1] https://lore.kernel.org/lkml/20200411155623.GA22175@zn.tnicReported-by: Borislav Petkov <bp@suse.de>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Jessica Yu <jeyu@kernel.org>
Co-developed-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change nfp driver to use globally defined kernel version.
Reported-by: Borislav Petkov <bp@suse.de>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use globally defined kernel version instead of custom driver variant.
Reported-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Get rid of linux/vermagic.h includes, so that MODULE_ARCH_VERMAGIC from
the arch header arch/x86/include/asm/module.h won't be redefined.

  In file included from ./include/linux/module.h:30,
                   from drivers/net/ethernet/3com/3c515.c:56:
  ./arch/x86/include/asm/module.h:73: warning: "MODULE_ARCH_VERMAGIC"
redefined
     73 | # define MODULE_ARCH_VERMAGIC MODULE_PROC_FAMILY
        |
  In file included from drivers/net/ethernet/3com/3c515.c:25:
  ./include/linux/vermagic.h:28: note: this is the location of the
previous definition
     28 | #define MODULE_ARCH_VERMAGIC ""
        |

Fixes: 6bba2e89 ("net/3com: Delete driver and module versions from 3com drivers")
Co-developed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Shannon Nelson <snelson@pensando.io> # ionic
Acked-by: Sebastian Reichel <sre@kernel.org> # power
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The variable rc is being assigned with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andy Shevchenko says:

====================
net: bcmgenet: Clean up after ACPI enablement

ACPI enablement series had missed some clean ups that would have been done
at the same time. Here are these bits.

In v2:
- return dev_dbg() calls to avoid spamming logs when probe is deferred (Florian)
- added Ack (Florian)
- combined two, earlier sent, series together
- added couple more patches
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

No need to have parentheses around plain pointer variable or
negation operator. Drop them for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It's convenient to use get_unligned_beXX() and put_unaligned_beXX() helpers
to get or set MAC instead of open-coded variants.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conversion to devm_clk_get_optional() makes it explicit that clocks are
optional. This change allows to handle deferred probe in case clocks are
defined, but not yet probed. Due to above changes bail out in error case.

While here, check potential error when enable main clock.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is nothing which needs a set of OF headers, followed by redundant
OF node ID check. Drop them for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When compiled with CONFIG_ACPI=n, ACPI_PTR() will be no-op, and thus
genet_acpi_match table defined, but not used. Compiler is not happy about
such data. Drop ACPI_PTR() for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5-updates-2020-04-20

This series includes misc updates and clean ups to mlx5 driver:

1) improve some comments from Hu Haowen.
2) Handles errors of netif_set_real_num_{tx,rx}_queues, from Maxim
3) IPsec and FPGA related code cleanup to prepare for ASIC devices
   IPsec offloads, from Raed
4) Allow partial mask for tunnel options, from Roi.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

A barrier is needed here to ensure that rtl_tx sees the descriptor
changes (DescOwn set) before the updated tp->cur_tx value. Else it may
wrongly assume that the transfer has been finished already. For this
purpose smp_wmb() is sufficient.

No separate barrier is needed for ordering the descriptor changes
with the MMIO doorbell write. The needed barrier is included in
the non-relaxed writel() used by rtl8169_doorbell().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replaced "its" with "it's".
Signed-off-by: Hu Haowen <xianfengting221@163.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Embedded CPU bit doesn't change with PCI resume/suspend.
Hence read it only once while probing the PCI device.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

netif_set_real_num_tx_queues and netif_set_real_num_rx_queues may fail.
Now that mlx5e supports handling errors in the preactivate hook, this
commit leverages that functionality to handle errors from those
functions and roll back all changes on failure.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

We use mapping to save and restore the tunnel options.
Save also the tunnel options mask.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

In notify HW (ring doorbell) flow, we set the bit to request a completion
on the TX descriptor.
When doing so, we should not unset other bits in the same byte.
Currently, this does not fix a real issue, as we still don't have a flow
where both MLX5_WQE_CTRL_CQ_UPDATE and any adjacent bit are set together.

Fixes: 542578c6 ("net/mlx5e: Move helper functions to a new txrx datapath header")
Fixes: 864b2d71 ("net/mlx5e: Generalize tx helper functions for different SQ types")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Currently the SA handle is created and managed as part of the common
code for different IPsec supporting HW, this handle is passed to HW
to be used on Rx to identify the SA handle that was used to
return the xfrm state to stack.

The above implementation pose a limitation on managing this handle.

Refactor by moving management of this field to the specific HW code.

Downstream patches will introduce the Connect-X support for IPsec that
will use this handle differently than current implementation.
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Reviewed-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The current HW counters are supported only by Innova, split the ipsec
stats group into two groups, one for HW and one for SW. And expose
the HW counters to ethtool only if Innova HW is used for IPsec offload.
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Currently the FPGA IPsec is the only hw implementation of the IPsec
acceleration api, and so the mlx5_accel_esp_create_hw_context was
wrongly made to suit this HW api, among other in its parameter list
and some of its parameter endianness.

This implementation might not be suitable for different HW.

Refactor by group and pass all function arguments of
mlx5_accel_esp_create_hw_context in common mlx5_accel_esp_xfrm_attrs
struct field of mlx5_accel_esp_xfrm struct and correct the endianness
according to the HW being called.
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Reviewed-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The cited commit relies on include <net/geneve.h> being included
implicitly prior to include "en_accel/en_accel.h".
This mandates that all files that needs to include en_accel.h
to redantantly include net/geneve.h.

Include net/geneve.h explicitly at "en_accel/en_accel.h" to avoid
undesired constrain as above.

Fixes: e3cfc7e6 ("net/mlx5e: TX, Add geneve tunnel stateless offload support")
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Currently the IPsec acceleration capability function is also used
at IPsec fpga capable device code.

This could cause a future bug as the acceleration layer is agnostic
to the device implementing its API.

Fix by using the IPsec FPGA capability function instead of acceleration
layer capability function in case of FPGA IPsec only related operations.

Downstream patches will add support for Connect-X IPsec, this can avoid
a future bug.
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Reviewed-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Fix the following coccicheck warning:

drivers/net/ethernet/qlogic/qed/qed_dev.c:4395:2-34: WARNING:
Assignment of 0/1 to bool variable
drivers/net/ethernet/qlogic/qed/qed_dev.c:1975:2-34: WARNING:
Assignment of 0/1 to bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Acked-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Huazhong Tan says:

====================
net: hns3: misc updates for -next

This patchset includes some misc updates for the HNS3 ethernet driver.

[patch 1&2] separates two bloated function.
[patch 3-5] removes some redundant code.
[patch 6-7] cleans up some coding style issues.
[patch 8-10] adds some debugging information.

Change log:
V1->V2:	removes an unnecessary initialization in [patch 1] which
	suggested by David Miller.
	modified some print format issue and commit log in [patch 8].
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds trace event support for PF/VF mailbox.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for dumping MAC reg in debugfs,
which will be helpful for debugging.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adds some debug information for failures of processing flow table,
removes the redundant printing when hclge_fd_check_spec() returns
error, and modifies the printing level for FD not enable error.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes some unnecessary blank lines, redundant
parentheses, and changes one tab to blank in
hclge_dbg_dump_reg_common().
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In hclge_set_fd_key_config(), parameter 'stage' should be
as enum HCLGE_FD_STAGE, and in hclge_config_key(), 'tuple_size'
should be type u8, also simplify unsigned int with u32 for 'i'.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>