- 01 Oct, 2018 7 commits
-
-
Lorenzo Bianconi authored
Move shared eeprom utility routines in mt76x02_eeprom.h and remove duplicated code Signed-off-by:
Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by:
Felix Fietkau <nbd@nbd.name>
-
Lorenzo Bianconi authored
Move mt76x2 and mt76x0 common definitions in mt76x02_eeprom.h and remove duplicated code Signed-off-by:
-
Felix Fietkau authored
Add stbc tx power eeprom parsing support for mt76x2 driver. When writing power entries, make a distinction between rates that are read from the same EEPROM value, but have separate register entries. No effect on runtime behavior, but preparation for unification with mt76x0 and for placing restrictions on individual rate power limits Signed-off-by:
-
Lorenzo Bianconi authored
Move seq_put_array utility routine in mt76-core module in order to be reused in mt76x0 driver Signed-off-by:
-
Lorenzo Bianconi authored
Add pci load firmware routine. Move some shared mcu definitions in mt76x02_mcu.h Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
-
Lorenzo Bianconi authored
Add mt7650 PCI id found on ASUS rt-51ac to pci_device_id table Signed-off-by:
-
Lorenzo Bianconi authored
Fix tx power configuration for VHT 1SS/STBC mcs 9 since in MT_TX_PWR_CFG_{8,9} mcs 8,9 bits are GENMASK(21,16) and GENMASK(29,24) while GENMASK(15,6) are marked as reserved Fixes: 7bc04215 ("mt76: add driver code for MT76x2e") Signed-off-by:
-
- 20 Sep, 2018 7 commits
-
-
YueHaibing authored
Fixes gcc '-Wunused-but-set-variable' warning: drivers/net/wireless/quantenna/qtnfmac/cfg80211.c: In function 'qtnf_dump_survey': drivers/net/wireless/quantenna/qtnfmac/cfg80211.c:694:19: warning: variable 'vif' set but not used [-Wunused-but-set-variable] Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Reviewed-by:
Sergey Matyukevich <sergey.matyukevich.os@quantenna.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Takashi Iwai authored
The ucode chunk might be relatively large and the allocation with kmalloc() may fail occasionally. Since the data isn't DMA-transferred but by manual loops, we can use vmalloc instead of kmalloc. For a better performance, though, kvmalloc() would be the best choice in such a case, so let's replace with it. Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=1103431Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
YueHaibing authored
Fixes gcc '-Wunused-but-set-variable' warning: drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c: In function 'brcmf_sdio_rxglom': drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c:1466:11: warning: variable 'sfdoff' set but not used [-Wunused-but-set-variable] drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c: In function 'brcmf_sdio_bus_preinit': drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c:3408:7: warning: variable 'pad_size' set but not used [-Wunused-but-set-variable] Signed-off-by:
-
zhong jiang authored
debugfs_remove_recursive has taken IS_ERR_OR_NULL into account. So just remove the condition check before debugfs_remove_recursive. Signed-off-by:
zhong jiang <zhongjiang@huawei.com> Signed-off-by:
-
Arend van Spriel authored
When obtaining the firmware capability a buffer is provided of 512 bytes. However, if all features in firmware are supported the buffer needs to be 565 bytes as otherwise truncated information is retrieved from firmware. Increasing the buffer to 768 bytes on stack. Reviewed-by:
Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by:
Franky Lin <franky.lin@broadcom.com> Signed-off-by:
Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by:
-
Arend van Spriel authored
Decoding of firmware channel information was not complete for 160MHz support. This resulted in the following warning: WARNING: CPU: 2 PID: 2222 at .../broadcom/brcm80211/brcmutil/d11.c:196 brcmu_d11ac_decchspec+0x2e/0x100 [brcmutil] Modules linked in: brcmfmac(O) brcmutil(O) sha256_generic cfg80211 ... CPU: 2 PID: 2222 Comm: kworker/2:0 Tainted: G O 4.17.0-wt-testing-x64-00002-gf1bed50 #1 Hardware name: Dell Inc. Latitude E6410/07XJP9, BIOS A07 02/15/2011 Workqueue: events request_firmware_work_func RIP: 0010:brcmu_d11ac_decchspec+0x2e/0x100 [brcmutil] RSP: 0018:ffffc90000047bd0 EFLAGS: 00010206 RAX: 000000000000e832 RBX: ffff8801146fe910 RCX: ffff8801146fd3c0 RDX: 0000000000002800 RSI: 0000000000000070 RDI: ffffc90000047c30 RBP: ffffc90000047bd0 R08: 0000000000000000 R09: ffffffffa0798c80 R10: ffff88012bca55e0 R11: ffff880110a4ea00 R12: ffff8801146f8000 R13: ffffc90000047c30 R14: ffff8801146fe930 R15: ffff8801138e02e0 FS: 0000000000000000(0000) GS:ffff88012bc80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f18ce8b8070 CR3: 000000000200a003 CR4: 00000000000206e0 Call Trace: brcmf_setup_wiphybands+0x212/0x780 [brcmfmac] brcmf_cfg80211_attach+0xae2/0x11a0 [brcmfmac] brcmf_attach+0x1fc/0x4b0 [brcmfmac] ? __kmalloc+0x13c/0x1c0 brcmf_pcie_setup+0x99b/0xe00 [brcmfmac] brcmf_fw_request_done+0x16a/0x1f0 [brcmfmac] request_firmware_work_func+0x36/0x60 process_one_work+0x146/0x350 worker_thread+0x4a/0x3b0 kthread+0x102/0x140 ? process_one_work+0x350/0x350 ? kthread_bind+0x20/0x20 ret_from_fork+0x35/0x40 Code: 66 90 0f b7 07 55 48 89 e5 89 c2 88 47 02 88 47 03 66 81 e2 00 38 66 81 fa 00 18 74 6e 66 81 fa 00 20 74 39 66 81 fa 00 10 74 14 <0f> 0b 66 25 00 c0 74 20 66 3d 00 c0 75 20 c6 47 04 01 5d c3 66 ---[ end trace 550c46682415b26d ]--- brcmfmac: brcmf_construct_chaninfo: Ignoring unexpected firmware channel 50 This patch adds the missing stuff to properly handle this. Reviewed-by:
-
https://github.com/nbd168/wirelessKalle Valo authored
mt76 patches for 4.20 * lots of mt76x0 cleanups / fixes * mt76x2u fixes * unify code between mt76x0, mt76x2e and mt76x2u * rename mt76x0 to mt76x0u * improve rx buffer allocation for all variants * prepare for adding mt76x0e (pci-e variant) support add CONFIG_MT76x0E kconfig symbol
-
- 19 Sep, 2018 26 commits
-
-
Lorenzo Bianconi authored
Remove mt76_fw dependency from mt76x0u_upload_firmware routine since it does not define firmware layout properly. Moreover use mt76_poll_msec utility routine to check if the fw is properly running Signed-off-by:
-
Lorenzo Bianconi authored
Remove unused usb header file and move mt76x0 firmware definition in usb.c Signed-off-by:
-
Lorenzo Bianconi authored
Remove mcu.c source file since it contains just 'one-line' function that is shared between PCI and USB code Signed-off-by:
-
Stanislaw Gruszka authored
Firmware loading is usb specific, move it to usb.c file. Signed-off-by:
-
Felix Fietkau authored
Using the NAPI or netdev frag cache along with other drivers can lead to 32 KiB pages being held for a long time, despite only being used for very few page fragments. This can happen if the driver grabs one or two fragments for rx ring refill, while other drivers use (and free up) the remaining fragments. The 32 KiB higher-order page can only be freed once all users have freed their fragments. Depending on the traffic patterns, this can waste a lot of memory and look a lot like a memory leak. Signed-off-by: -
Lorenzo Bianconi authored
Move mt76x2_phy_tssi_compensate routine in mt76x2-common module since it is shared between mt76x2 and mt76x2u drivers Signed-off-by:
-
Lorenzo Bianconi authored
Move mcu_calibrate routine in mt76x02-lib module since it is shared between USB and PCI code. Moreover remove duplicated code Signed-off-by:
-
Lorenzo Bianconi authored
Move shared mt76x2 {pcie/usb} mcu shared code in a common file and remove duplicated code Signed-off-by: -
Lorenzo Bianconi authored
Move shared mt76x2/mt76x0 mcu shared code in a common file and remove duplicated code Signed-off-by:
-
Lorenzo Bianconi authored
Move mt76x2_fw_header definition in mt76x02_mcu.h and remove duplicated code Signed-off-by:
-
Lorenzo Bianconi authored
Use mcu common helpers instead of mt76x2 specific routines for mcu_alloc_msg()/mcu_send_msg(). This is a preliminary patch to unify mt76e and mt76u mcu code Signed-off-by:
-
Lorenzo Bianconi authored
Use mt76_dev data structure instead of mt76x2_dev one in mt76x2_mcu_msg_send and mt76x2_mcu_get_response routines. Moreover add wait_resp parameter to mt76x2_mcu_msg_send signature. This is a preliminary patch in order to unify mcu_msg_alloc()/mcu_msg_send() between pcie and usb code Signed-off-by:
-
Lorenzo Bianconi authored
Move __iomem regs pointer in mt76_mmio data structure Signed-off-by:
-
Lorenzo Bianconi authored
Introduce mt76_mmio data structure in mt76_dev and move mt76x2_mcu in mt76_mmio. This is a preliminary patch to unify mcu code between mt76x02{e,u} drivers Signed-off-by: -
Lorenzo Bianconi authored
Remove unused usb buffer in mt76x2_mcu data structure Signed-off-by:
-
Lorenzo Bianconi authored
Use mt76_dev data structure instead of mt76x2_dev one in mt76x2_tx_queue_mcu routine. This is a preliminary patch to share mcu code between mt76x2e and mt76x0e Signed-off-by:
-
Lorenzo Bianconi authored
Remove mt76_mcu_msg_alloc return value check since it is already evaluated in __mt76x02u_mcu_send_msg Signed-off-by:
-
Stanislaw Gruszka authored
We don't need to use custom burst write regs via MCU, we can use generic mt76_wr_copy() for the same purpose. Signed-off-by:
-
Stanislaw Gruszka authored
mt76x0_burst_read_regs is not used, but keep it for eventual use. Since we have this function now in the driver git history, we can remove it and eventually revert this commit it the function will be needed. Signed-off-by:
-
Lorenzo Bianconi authored
Add static qualifier to mt76x02_remove_dma_hdr routine and do not export the symbol since it is only used in mt76x02_util.c Signed-off-by:
-
Lorenzo Bianconi authored
Introduce mt76x02_dma.h header file to contain mt76x02 dma related definitions Signed-off-by:
-
Lorenzo Bianconi authored
Move mt76u_skb_dma_info routine in mt76x02-usb module and rename it in mt76x02u_skb_dma_info. Moreover move mt76x02u_set_txinfo in mt76x02_usb_core.c. This is a preliminary patch to move MT_TXD_INFO, MT_MCU_MSG and MT_RX_FCE_INFO defs in mt76x02-lib module since other chipsets (e.g. mt7603) use different dma definitions Acked-by:
-
Lorenzo Bianconi authored
Introduce mt76x02_usb_mcu.c in order to contain mt76x02u mcu related code. Add mt76x02-usb module as a container for mt76x02 usb code. This is a preliminary patch to move MT_TXD_INFO, MT_MCU_MSG and MT_RX_FCE_INFO defs in mt76x02-lib module since other chipsets (e.g. mt7603) use different dma definitions Acked-by:
-
Lorenzo Bianconi authored
Use mcu common helpers instead of usb specific routines. Add static qualifier to the following functions: - mt76u_mcu_msg_alloc - __mt76u_mcu_send_msg - mt76u_mcu_send_msg - mt76u_mcu_wr_rp - mt76u_mcu_rd_rp - mt76u_wr_rp - mt76u_rd_rp This is a preliminary patch to move mt76x02 usb mcu code in mt76x02-usb module Acked-by:
-
Stanislaw Gruszka authored
Add callbacks for reading and writing reg pairs tables. Signed-off-by:
-
Stanislaw Gruszka authored
Add USB implementation for read and write reg pair routines. The actual implementation can use mcu related routines according to MCU state Signed-off-by:
-
