Check for error status bits on the AdminQ event queue and announce them
if seen.  If the Firmware sets these bits, it will trigger an AdminQ
interrupt to get the driver's attention to process the ARQ, which will
likely be enough to clear the actual issue.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Change-ID: I009e0ebc8be764e40e193b29aed2863f43eb5cb0
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

John W. Linville says:

====================
pull request: wireless-next 2014-06-06

Please accept this batch of fixes intended for the 3.16 stream.

For the bluetooth bits, Gustavo says:

"Here some more patches for 3.16. We know that Linus already opened the merge
window, but this is fix only pull request, and most of the patches here are
also tagged for stable."

Along with that, Andrea Merello provides a fix for the broken scanning
in the venerable at76c50x driver...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2014-06-08

This series contains updates to i40e and i40evf.

Jesse fixes an issue reported by Eric Dumazet where the driver was not
masking the right bits in the receive descriptor before checking them.
Also fixes TSO accounting since the kernel now can send as much as 32kB
in a single skb->frag[.] entry, even on a system with 4kB pages.

Anjali cleans up registers which are no longer supported.

Akeem cleans up code comments and removes num_msix_entries from the
interrupt setup routine since it was not being used.  Fixes an issue where
FD SB/ATR and NTUPLE configuration status were reported erroneously, so
now the driver reports FDir without further information.  Fixes a coding
error where during the registration for NAPI, the driver was requesting
256 budget.  The max recommended value for this NAPI_POLL_WEIGHT or 64.
Lastly, removed deprecated device IDs because they will not be shipped.

Mitch removes log messages which were redundant so therefore unnecessary.
Also removes a bogus code comment since VF drivers require MSI-X or they
won't get interrupts at all and cleans up the formatting of several log
messages.  Mitch also fixes the possibility of null pointers in VSI, since
not all VSIs have transmit rings.

Shannon ensures to clear the PXE mode bit on each reset after the AdminQ
has been rebuilt.

Catherine bumps the driver versions for i40e and i40evf.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Bump i40e to 0.4.5 and i40evf to 0.9.29.

Change-ID: I9faca5544446518c5425612e733499cf16ef20a1
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove two device IDs 1582 and 1573, because they will not be shipped.

Change-ID: Ica2e550b5b21a69e3f353eba2fe5e1c532a548c4
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix a coding error where during the registration for NAPI
the driver requested 256 budget.  The max recommended
value for this is NAPI_POLL_WEIGHT or 64.

Change-ID: I03ea1e2934a84ff1b5d572988b18315d6d91c5c6
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The TSO logic in the transmit path had some assumptions that
have been broken now that the kernel can send as much as 32kB
in a single skb->frag[.] entry, even on a system with 4kB pages.

This fixes the assumptions and allows the kernel to operate
as efficiently as possible with both SENDFILE and SEND.

In addition, the hardware limit of data contained in a descriptor is
changed to the next power of two below where it currently is in
order to align to a power of two value, preventing a single byte
of data in a descriptor.

Change-ID: I6af1f0b87c1458e10644dbd47541591075a52651
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Both the PF side and the VF side of the VF reset process are too noisy.
We already warn the user that a reset is happening, and that is
sufficient.

Because some of these message are inside if statements, we have to
rejigger the brackets at the same time to keep our coding style
consistent.

Change-ID: Id175562fb0ec7c396d9de156b4890e136f52d5f4
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Once more, with feeling: not all VSIs have rings. To assume so is to
invite null pointers to your party.

Change-ID: I576858824468d9712d119fa1015a1f28c27712c4
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Be sure to clear PXE mode bit on each reset after AdminQ has been rebuilt.

Change-ID: I992d8c79594f8ca0660c50844ace675ecb9c9bf2
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes an issue where FD SB/ATR and NTUPLE configurations status are
reported erroneously. Without this patch, driver reports FDir without further
information.

Change-ID: I5bdd2871b7f2db1e5f5e76c741ae6a0dc603b453
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The correct format is %pM, not %pMAC.

Change-ID: Idb335723a966fe56db3a72b9c07c08ca66f9db3c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Clean up inconsistent log messages, mostly related to punctuation. Based
on the dogma that "kernel messages are not sentences", remove all
trailing periods. Reword a few of the messages to make them less
sentence-like.

Change-ID: Ibd849aa7623a77549b0709988c66ab05d1311472
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This comment is just plain false. VF drivers require MSI-X or they won't
get interrupts at all.

Change-ID: Iaea5e30b6926948aa834a3c506d9a9223d9e3e29
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

We don't need to print log messages when we encounter an out-of-memory
condition, as the allocator will do this for us. Also, remove a Tx hang
message that duplicates the one emitted by the netdev layer, and a
duplicate message in the watchdog.

Change-ID: If2056e6135fe248f66ea939778f9895660f4d189
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

1. There is no ixgbe_watchdog_task function in the driver, so change
   the comment to the correct function name, i40e_watchdog_subtask.
2. Remove num_msix_entries from interrupt set_up routine
   because it is never used.
3. Remove some TBD comments that are not needed.

Change-ID: I37697a04007074b797f85fd83d626672e4df1ad1
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove use of registers no longer supported.

Change-ID: I9d27399091cea78a926489d94f958edd762f5a20
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

As reported by Eric Dumazet, the driver is not masking the right
bits in the receive descriptor before it starts checking them.

This patch extends the mask to allow for the right bits to be
checked, and fixes the issue permanently via a define.

CC: Eric Dumazet <eric.dumazet@gmail.com>
Change-ID: I3274f7619057a950f468143e6d7e11b129f54655
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

During key removal, the key object is freed, but not taken out of the
llsec key list properly. Fix that.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

The include of asm/cputype.h breaks the powerpc build. This
include was accidentally left in from driver debugging and
can be removed.

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>,
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2014-06-06

This series contains updates to i40e and i40evf.

Shannon sets the lan_veb index when the Virtual Ethernet Bridge (VEB) is
created for the basic LAN device and its Virtual Switch Interfaces (VSIs).
Also adds the VEB/VSI statistics in the ethtool stats output.  Increases the
reset wait time because the original time was too optimistic and resets
were failing after EMPR.  This won't delay the actual wait, just allows
us to poll more times as needed.  He fixes the attempted removal of the
HMC space and unhook IRQs when a reset recovery fails because the HMC space
never got setup and IRQs are already unhooked in the first place, so the
removal is not necessary.

Jesse adds a log message for pre-production hardware so that the user is
notified that there may be issues with the hardware, yet does not prevent
the user from using the hardware.  Add the printing of link messages
in the i40e driver like all the other Intel Ethernet drivers.

Mitch makes log message changes to i40evf to prevent confusion by making
the most common messages less scary by lowering them to a less terrifying
log level.  This is due to the fact that depending on the timing of what
the PF driver is doing, it may take a few tries before the VF driver is able
to communicate with the PF driver on init or reset recovery.

Kamil provides a change to prevent the driver from getting into a endless
loop while trying to send GetVersion AQ command, since BO silicon blocks
AQ registers when in Blank Flash mode.  So introduce a simple check for a
correct value in one of the AQ registers to be sure that AQ was configured
correctly.

Matt adds a function which indicates our intention to enable or disable a
particular transmit queue.  Also adds a function to notify the device's
transmit unit that we are about to enable or disable a transmit queue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem

Bump i40e to 0.4.3 and i40evf to 0.9.27.

Change-ID: I4141e9f8615bdcfa3b1b5ecbc2ac62603a03b7ad
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Use an extra state variable to keep track of when the IRQs are fully
set up.  This keeps us from trying to unhook IRQs that already were
left unhooked in a failed reset recovery, e.g. when firmware is broken.

Change-ID: I073eb081e4ef8aedcbdf1ee0717c0ed64fa172f2
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

If a reset recovery failed (e.g. firmware is broken), the HMC space won't
get set up.  We don't need to try to delete it if it didn't get set up.
This stops some needless error messages when we already know we need to
just tear things down.

Change-ID: Iac600481765e20b136052b43a544e55d7870268b
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The i40e driver should print link messages like all the
other Intel Ethernet drivers.

Change-ID: Ia88bdb96794e17a3962fcea94db176de01f921f7
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add the missing unicast, multicast, and broadcast stats for the port.

Change-ID: Ifc366d7b7745f70eaac9d00eeb0694eb9ec076a9
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add VSI HW stats for unicast, multicast, and broadcast for Rx and Tx.
Stop printing the netdev multicast value because it doesn't include Tx
and would be confusing.

Change-ID: I08278b6657e7c838fd29a4a1f305f78fe1b150be
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The wait time was originally too optimistic and the resets were failing
after EMPR.  This increases the loop count to wait considerably longer.
This won't delay the actual wait longer than really needed, just allows
us to poll more times as needed.

Change-ID: If7b96f55cc25b8d06cbbe8665259d250188c53d7
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add a function which indicates our intention to enable or disable a particular
Tx queue. Also add a function to notify the device's Tx unit that we're about
to enable or disable a Tx queue.

Change-ID: I6adf3cbb5bb3e3c984d1ec969e06577c19ef296d
Signed-off-by: Matt Jared <matthew.a.jared@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

B0 Si blocks AQ registers when in Blank Flash mode - write is dropped,
read gives 0xDEADBEEF. Introduce a simple check for a correct value in one
of the AQ registers to be sure that AQ was configured correctly.
Without this check we get into an endless loop while trying to send
GetVersion AQ cmd.

Change-ID: I00102b8c5fa6c16d14289be677aafadf87f10f0d
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Depending on the timing of what the PF driver is doing, it make take a
few tries before the VF driver is able to communicate with the PF driver
on init or reset recovery. In order to prevent confusion, make the most
common messages less scary by lowering them to a less terrifying log
level and indicate that the driver will retry.

Change-ID: I1ec22aa59a68f4469aabe14775a1bfc1ab4b7f2f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver and hardware are not expected to work correctly
with revision_id 0 hardware.  Don't prevent the user from
using it, but be sure to print a warning.

Change-ID: I3712d34752bfad458078a5f35dfd0aa0ae9fd20e
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Print the VEB statistics in the ethtool stats output.

Change-ID: Ic93d4c3922345c43e4cfd7f7e7a906844dd2f49f
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When the VEB is created for the basic LAN device and its VSIs, we need to
set the tracking lan_veb index for later use.

Change-ID: I66bb74993bbda3621ca557437cb4b3517f9b315b
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

To avoid the confusion of having two variables, shrink the function to
only use the parameter variable for looping.

Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/xen-netback/netback.c
	net/core/filter.c

A filter bug fix overlapped some cleanups and a conversion
over to some new insn generation macros.

A xen-netback bug fix overlapped the addition of multi-queue
support.
Signed-off-by: David S. Miller <davem@davemloft.net>

BPF classic->internal converter broke SKF_AD_PKTTYPE extension, since
pkt_type_offset() was failing to find skb->pkt_type field which is defined as:
__u8 pkt_type:3,
     fclone:2,
     ipvs_property:1,
     peeked:1,
     nf_trace:1;

Fix it by searching for 3 most significant bits and shift them by 5 at run-time

Fixes: bd4cf0ed ("net: filter: rework/optimize internal BPF interpreter's instruction set")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Tested-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>