From Jason Cooper, mvebu defconfig changes for v3.12:

 - kirkwood: add i2c devices, ext4, r8169
 - mvebu: gpio-keys, input event
 - dove: SI5351, PCI, xHCI

* tag 'defconfig-3.12' of git://git.infradead.org/linux-mvebu:
  ARM: dove: update dove_defconfig with SI5351, PCI, and xHCI
  ARM: mvebu: add gpio-keys and input event support in defconfig
  ARM: Kirkwood: update defconfig for used i2c devices, EXT4 FS, r8169
Signed-off-by: Olof Johansson <olof@lixom.net>

From Jason Cooper, mvebu boards changes for v3.12:

 - kirkwood
    - convert Dockstar, Guruplug, mv88f6281gtw_ge to DT
    - remove legacy boards (which have DT support) sheevaplug, lacie boards
    - ARRAY_AND_SIZE() cleanup

 - dove
    - some DT node updates (depends on irqchip/clocksource DT changes earlier)
    - add the D2Plug board

* tag 'boards-3.12-2' of git://git.infradead.org/linux-mvebu:
  ARM: dove: add initial DT file for Globalscale D2Plug
  ARM: dove: add GPIO IR receiver node to SolidRun CuBox
  ARM: dove: add common pinmux functions to DT
  ARM: dove: add cpu device tree node
  arch/arm/mach-kirkwood: Avoid using ARRAY_AND_SIZE(e) as a function argument
  ARM: kirkwood: fix DT building and update defconfig
  ARM: kirkwood: Remove all remaining trace of DNS-320/325 platform code
  ARM: kirkwood: use dts pre-processor for mv88f6281gtw-ge
  ARM: kirkwood: convert the mv88f6281gtw_ge board to DT
  ARM: kirkwood: remove LaCie boards that are supported through DT
  ARM: kirkwood: remove support for legacy booting of Sheevaplug
  ARM: kirkwood: remove support for legacy booting of Guruplug
  ARM: kirkwood: remove support for legacy booting of Dockstar
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-boards-cleanup-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/boards

From Simon Horman:
Renesas ARM based SoC boards cleanups for v3.12

* Add __initdata annotations to lager board
* Add __initconst annotations to ape6evm board

* tag 'renesas-boards-cleanup-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: lager: add missing __initdata
  ARM: shmobile: ape6evm: add "__initconst" annotations where needed
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-boards2-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/boards

From Simon Horman:
Second round of Renesas ARM-based SoC board updates for v3.12

* Enable ether on lager board
* Enable GPIO LEDs and switches on ape6evm board

* tag 'renesas-boards2-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: lager: enable Ether
  ARM: shmobile: ape6evm: Add GPIO LEDs
  ARM: shmobile: ape6evm: support GPIO switches
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-defconfig-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/boards

From Simon Horman:
Renesas ARM based SoC defconfig updates for v3.12

* Enable GPIO LEDs and keys for ape6evm board
* Enable ARM_APPENDED_DTB for marzen board
* Add lager defconfig board

* tag 'renesas-defconfig-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: ape6evm: Enable gpio-leds in defconfig
  ARM: shmobile: ape6evm: Enable gpio-keys in defconfig
  ARM: shmobile: Add lager defconfig
  ARM: shmobile: marzen: Enable ARM_APPENDED_DTB in defconfig
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-boards-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/boards

From Simon Horman:
Renesas ARM-based SoC board updates for v3.12

* ape6evm: Add SDHI and MMCIF support
* lager: Add MMCIF support
* armadillo800eva: Add DMA support for MMCIF

* tag 'renesas-boards-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (54 commits)
  ARM: shmobile: ape6evm: add SDHI interfaces
  ARM: shmobile: ape6evm: add MMCIF support
  ARM: shmobile: select the fixed regulator driver on BockW
  ARM: shmobile: lager: add MMCIF support
  ARM: shmobile: armadillo800eva: add DMA support to MMCIF
  ARM: shmobile: Setup r8a7790 arch timer based on MD pins
  ARM: shmobile: Introduce r8a7790_read_mode_pins()
  ARM: shmobile: r8a7740: add MMCIF DMA definitions
  ARM: shmobile: Disconnect EMEV2 SMP code from clocks
  ARM: shmobile: Make r8a73a4 Arch timer optional
  ARM: shmobile: Add r8a73a4 CMT10 clock event
  ARM: shmobile: Make r8a7790 Arch timer optional
  ARM: shmobile: Add r8a7790 CMT00 clock event
  ARM: shmobile: Sort r8a7790 MSTP entries
  ARM: shmobile: r8a73a4: add clocks for I2C controllers
  ARM: shmobile: r8a73a4: add Z2 clock support
  ARM: shmobile: r8a73a4: safeguard against wrong clk_set_rate() uses
  ARM: shmobile: r8a73a4: implement CPU clock scaling for CPUFreq
  ARM: shmobile: r8a73a4: wait for completion when kicking the clock
  ARM: shmobile: r8a7790: add thermal driver support
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-tpu-pwm-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/boards

From Simon Horman:
Renesas TPU PWM support for v3.12

Add Renesas TPU PWM unit support

* tag 'renesas-tpu-pwm-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  leds: Remove leds-renesas-tpu driver
  ARM: shmobile: sh73a0: Remove all GPIOs
  ARM: shmobile: kota2: Use leds-pwm + pwm-rmob
  ARM: shmobile: armadillo800eva: Add backlight support
Signed-off-by: Olof Johansson <olof@lixom.net>

This adds an initial DT file for the Globalscale D2Plug with Dove SoC.
Currently, one LED is missing and I have not been able to get SD8787 driver
working. Those will be taken care of later.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

This adds a node for the IR receiver connected to a GPIO pin on the
SolidRun CuBox.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

This adds common dedicated and gpio pinmux functions to SoC pinctrl
node. It also relocates pinctrl references to corresponding DT nodes.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

This adds a node for the Marvell Sheeva PJ4A CPU found on Dove SoCs.
While at it, also move the l2-cache node out of internal registers and
consistently name different nodes.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Conflicts:
	arch/arm/boot/dts/dove.dtsi

This adds SI5351 clock driver found on the SolidRun CuBox, PCI driver
and USB 3.0 xHCI driver found on the Globalscale D3Plug to dove_defconfig.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Replace ARRAY_AND_SIZE(e) in function argument position to avoid hiding the
arity of the called function.

The semantic match that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression e,f;
@@

f(...,
- ARRAY_AND_SIZE(e)
+ e,ARRAY_SIZE(e)
  ,...)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

commit

  844703c1 ARM: kirkwood: Remove all remaining trace of DNS-320/325 platform code

removed the last kirkwood DT/platform board in kirkwood_defconfig, this
triggered a rescan of the config symbols, the result of which breaks the
build because KIRKWOOD_DT does not select OF_IRQ.

This commit fixes the regression and updates the defconfig to
explicitly enable SERIAL_OF_PLATFORM and KIRWOOD_DT.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

No platform code left now, so remove all references to it.

The reset gpio code didn't work to begin with, it will be replaced with
a DT node at a future date. -jc
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

From Jason Cooper:
mvebu boards changes for v3.12

 - convert kirkwood, dove, orion5x to DT init of mv643xx_eth
    - _lots_ of board code removal :)
 - convert kirkwood, dove and orion5x to DT init of clocksource and irqchip

* tag 'boards-3.12' of git://git.infradead.org/linux-mvebu:
  ARM: plat-orion: add reg offset to DT irq driver stub
  ARM: kirkwood: remove obsolete SDIO clock gate workaround
  ARM: kirkwood: convert to DT irqchip and clocksource
  ARM: dove: convert to DT irqchip and clocksource
  ARM: orion5x: update intc device tree node to new reg layout
  ARM: kirkwood: move device tree nodes to DT irqchip and clocksource
  ARM: dove: move device tree nodes to DT irqchip and clocksource
  ARM: orion5x: remove legacy mv643xx_eth board setup
  ARM: kirkwood: remove legacy clk alias for mv643xx_eth
  ARM: kirkwood: remove redundant DT board files
  ARM: dove: remove legacy mv643xx_eth setup
  ARM: orion5x: add gigabit ethernet and mvmdio device tree nodes
  ARM: kirkwood: add gigabit ethernet and mvmdio device tree nodes
  ARM: dove: add gigabit ethernet and mvmdio device tree nodes
  + Linux 3.11-rc2
Signed-off-by: Olof Johansson <olof@lixom.net>

Signed-off-by: Jason Cooper <jason@lakedaemon.net>

This commit converts the mv88f6281gtw_ge Kirkwood board to use a
Device Tree representation, except for the Ethernet devices and the
DSA switch. Even though the mv643xx_eth driver has a DT binding,
converting this board to use it is for now left on the side because it
doesn't use a simple PHY, but a DSA switch instead.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The "LaCie Internet Space v2 NAS Board", "LaCie Network Space Max v2
NAS Board" and "LaCie Network Space v2 NAS Board" boards are all
supported through the Device Tree.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The Kirkwood Sheevaplug platform has already been converted to the
Device Tree, so we can remove the legacy booting option for this
platform.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The Kirkwood Guruplug platform has already been converted to the
Device Tree, so we can remove the legacy booting option for this
platform.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The Kirkwood Dockstar platform has already been converted to the
Device Tree, so we can remove the legacy booting option for this
platform.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The board has 6 LEDs connected to GPIOs. Add a led-gpio device to
support them.
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The ape6evm board has switches S16 - S23 wired up to GPIO pins.
This patch allows access to those pins as gpio-keys.
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch adds missing __initdata to driver data/resource
which are used from platform_device_register_xxx()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Merge tag 'renesas-backlight-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/boards

From Simon Horman:
Renesas ARM and SH based SoC backlight drivers for v3.12

Backlight drivers used by SH and ARM SH-Mobile boards.

* tag 'renesas-backlight-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: mach-shmobile: ag5evm: Use bd6107 backlight driver
  sh: kfr2r09: Use lv5207lp backlight
  sh: ecovec24: Use gpio-backlight
  ARM: mach-shmobile: mackerel: Use gpio-backlight
  backlight: Add ROHM BD6107 backlight driver
  backlight: Add Sanyo LV5207LP backlight driver
  backlight: Add GPIO-based backlight driver
Signed-off-by: Olof Johansson <olof@lixom.net>

Some Armada 370/XP boards have GPIO buttons, so it makes sense to
enable gpio-keys and the input event interface in mvebu_defconfig.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

This patch adds __initconst markers to the platform data and resources,
used on ape6evm as parameters to platform_device_register_resndata().
The data is duplicated inside that function, therefore original data
can be discarded after initialisation is completed.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This is intended to be used until multi-arch is able to be
used for the lager board at which time a more generic configuration
will be used in place of this one.
Acked-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

"ARM: shmobile: marzen: Switch to DT_MACHINE_START" moves marzen
over to use DT_MACHINE_START, however, the prevalent boot loader
does not support booting with a separate dtb. Thus, it makes
sense to use ARM_APPENDED_DTB by default.

This is consistent with other shmobile defconfigs.
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

With irqchip driver for Orion SoCs, reg layout of orion-intc has changed.
This updates irq driver stub implemented before to the new reg layout by
adding an offset to the base address passed by DT node. As orion5x still
uses this stub, it cannot be removed yet.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Kirkwood DT boards have been converted to DT SDIO already, we can now
remove the legacy clock gate workaround for SDIO clock.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

With recent support for true irqchip and clocksource drivers for Orion
SoCs, now make use of it on DT enabled Kirkwood boards.

This also introduces a new Kconfig option for legacy (non-DT) Kirkwood
where old code is moved out to and polishes DT board file a little bit.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

With recent support for true irqchip and clocksource drivers for Orion
SoCs, now make use of it on DT enabled Dove boards.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Future irqchip driver for Orion SoCs has a modified reg layout starting
from CAUSE register. The former DT irq driver stub just used what the
non-DT driver wants. Currently, orion5x is not ready for irqchip driver
because of legacy timer and missing DT clk provider. To ease future
conversion and just because orion-intc binding documentation already
reflects new reg layout, we convert orion5x DT now.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

With recent support for true irqchip and clocksource drivers for Orion
SoCs, now make use of it on DT enabled Kirkwood boards.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

With recent support for true irqchip and clocksource drivers for Orion
SoCs, now make use of it on DT enabled Dove boards.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>