i.MX6SLL EVK board has WDOG_B pin connected to the PMIC;

Add the WDOG_B pinctrl entry and 'fsl,ext-reset-output'
property to wdog node to let watchdog trigger a system
POR reset via the PMIC.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

On i.MX6SLL EVK board, there is a debug LED controlled
by MX6SLL_PAD_EPDC_VCOM1__GPIO2_IO04 pin, add support
for it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The imx6qdl-sabreauto boards have a pcie slot so let's enable it.

Tested on imx6dl-sabreauto with an atk9k wifi card; scanning works.

There are unhandled differences for imx6qp but imx6qp-sabreauto.dts
already contains a snippet explicitly disabling the &pcie node so that
can be dealt with later.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Boards based on imx6sl have duplicate memory nodes:

- One coming from the board dts file: memory@

- One coming from the imx6sl.dtsi file.

Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Boards based on imx6sx have duplicate memory nodes:

- One coming from the board dts file: memory@

- One coming from the imx6sx.dtsi file.

Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Boards based on imx6ul have duplicate memory nodes:

- One coming from the board dts file: memory@

- One coming from the imx6ul.dtsi file.

Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add memory node to board dts.

This is done in preparation of removing the memory node from imx6ul.dtsi.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Current imx7d-sdb.dts has some incorrect settings about
Rev-A and Rev-B boards, some of the settings are based on
Rev-A board but some are based on Rev-B board, clean up it
by adding i.MX7D SDB Rev-A board support, make default
imx7d-sdb.dts for Rev-B board as usual, and introduce
imx7d-sdb-reva.dts for Rev-A board. Below are the affected
differences of Rev-A and Rev-B board:

                Rev-A           Rev-B
USB_OTG2_PWR:   UART3_CTS_B     GPIO1_IO07
ENET_EN_B:      None            GPIO1_IO04
TP_INT_B:       EPDC_DATA13     EPDC_BDR1
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.

Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.

Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch adds support for the emtrion GmbH emCON-MX6 modules.
They are available with imx.6 Solo, Dual-Lite, Dual and Quad
equipped with Memory from 512MB to 2GB (configured by U-Boot).

Our default developer-Kit ships with the Avari baseboard and the
EDT ETM0700G0BDH6 Display (imx6[q|dl]-emcon-avari).

The devicetree is split into the common part providing all module
components and the basic support for all SoC versions
(imx6qdl-emcon.dtsi) and parts which are i.mx6 S|DL and D|Q relevant.
Finally the support for the avari baseboard in the developer-kit
configuration is provided by the emcon-avari dts files.
Signed-off-by: Jan Tuerk <jan.tuerk@emtrion.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Document the compatible strings for emtrion emCON-MX6 SoM's.
Signed-off-by: Jan Tuerk <jan.tuerk@emtrion.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Adding the label cpu0 allows the adjustment of cpu-parameters
by reference in overlaying dtsi files in the same way as it
is possible for imx6q devices.
Signed-off-by: Jan Tuerk <jan.tuerk@emtrion.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Some SOCs in the i.MX6 family have a USB host controller that is
only capable of the HSIC interface and has no on-board PHY.

To be able to use these controllers, we need to add "usb-nop-xceiv"
dummy PHYs.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

From i.MX6SX reference manual CCM chapter, KPP and
WDOGn use IPG clock as their clock, specify IPG
clock for KPP and WDOGn instead of DUMMY clock.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Removed the wrong compatible string "snps,dw-pcie", in case
match incorrect driver.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Removed the compatible string "snps,dw-pcie", it is for the reference
platform driver for PCI RC IP Protoyping Kits based on the ARC SDP,
so it is not suitable for all platform with designware PCIe controller,
and platform vendors have themselves' drivers.

The compatible string "snsp,dw-pcie" was added by mistake and it's not
matched that time, but it is matched because PCIe drivers has been
collected recently.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The PCIe compatible string for LS1043A was lost, so add it.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Boards based on imx7 have duplicate memory nodes:

- One coming from the board dts file: memory@

- One coming from the imx7s.dtsi file.

Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Boards based on imx35 have duplicate memory nodes:

- One coming from the board dts file: memory@

- One coming from the imx35.dtsi file.

Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Boards based on imx31 have duplicate memory nodes:

- One coming from the board dts file: memory@

- One coming from the imx31.dtsi file.

Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

According to Documentation/devicetree/bindings/media/fsl-pxp.txt,
only one PXP clock needs to be described and it should be named
"axi".

Also pass the compatible string as suggested in the bindings doc.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Remove "regulator-always-on" property for vddpu regulator
since it can be OFF when GPU power domain is OFF.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The "fsl,mf-mix-wakeup-irq" is ONLY used as a temporary
solution in NXP's internal tree for Mega/Fast Mix off
feature after suspend, upstream kernel does NOT need it,
remove it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Boards based on imx53 have duplicate memory nodes:

- One coming from the board dts file: memory@

- One coming from the imx53.dtsi file.

Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Boards based on imx51 have duplicate memory nodes:

- One coming from the board dts file: memory@

- One coming from the imx51.dtsi file.

Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This allows a board to specify a custom thermal zone configuration
involving the SoC internal sensor, CPU and GPU nodes without having
to change those nodes.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Use the correct compatible for the new protocol used by the firmware
on the touch controller, the GPIO wakeup isn't used in that case.
Also eGalax touch needs axis swapping, just as with the RMI4 touch.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch corrects indentation problems in the gpmigrp and i2c1grp nodes.
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The wireless variants of the ConnecCore 6UL SOM include a Qualcomm
QCA6564 wireless chip with dual WiFi and Bluetooth.

Both the ConnectCore 6UL SBC Express and Pro boards fit a wireless SOM.

The Wifi is connected through the SDIO interface on usdhc1 and the
Bluetooth is connected via uart1.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the status property disable the PCIe, the property will be enable
by bootloader.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Leave b{4,6}50v3 GPIO expander pca953x pins P05,P10,P11 unconfigured as
they are now used to implement an additional watchdog mechanism in user
space.  P10,P11 pins remain unused (and therefore hogged) on b850v3.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The i.MX25 contains two EPIT (Enhanced Periodic Interrupt Timer)
function blocks. Add their ipg and per clocks to the device tree.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Acked-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX6 SoCs has MMDC clock gates in CCM CCGR, add
clock property for MMDC driver's clock operation.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Drop reg property from fixed regulator and remove the unncessary bus
node.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This would help us to get early boot logs by passing "earlycon" to
kernel bootargs.

Further, by adding this we don't have to depend on complex earlyprintk
configs for early boot logs.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The DCP block on 6ull has no major differences other than requiring
explicit clock enabling.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This commit adds DTS support for BK4 device from Liebherr. It
uses vf610 SoC from NXP.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add Pincfgs for UART4 to enable Communication with the onboard SAM3X
Signed-off-by: Markus Kueffner <kueffner.markus@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for the ZII SCU 4 board, which has lots of switches and
SFF ports.

Based on the work from Andrew Lunn.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>