- 20 Jun, 2017 40 commits
-
-
Daniel Scheller authored
The values used for comparing symbol rates and the resulting conditional reg writes seem wrong (rates multiplied by ten), so fix those values. While this doesn't seem to influence operation, it should be fixed anyway. Signed-off-by:
Daniel Scheller <d.scheller@gmx.net> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com>
-
Daniel Scheller authored
In some configurations (due to different PIN config, wiring or so), the QAM FECLock might be signalled using a different register than F367CAB_QAMFEC_LOCK (e.g. F367CAB_DESCR_SYNCSTATE on Digital Devices hw), so make that register selectable. Signed-off-by:
-
Daniel Scheller authored
Currently, if_khz is set and provided using the configuration var in struct stv0367_config. However, in some constellations, the value might be different for differing channel bandwidths or even -T and -C operation. When e.g. used in conjunction with TDA18212 tuners, the tuner frontend might be aware of the different freqs. This factors if_khz retrieval in a function, which checks a new flag if an automatic retrieval attempt should be made, and if the tuner provides it, use it whenever needed. Signed-off-by:
-
Daniel Scheller authored
Every time dvb_frontend_ops.set_frontend() is called, an almost full reinit of the demodulator will be performed. While this might cause a slight delay when switching channels due to all involved tables being rewritten, it can even be dangerous in certain causes in that the demod may lock up and requires to be powercycled (this can happen on Digital Devices hardware). So this adds a flag if it should be done, and to not change behaviour with existing card support, it'll be enabled in all cases. Signed-off-by:
-
Daniel Scheller authored
This moves the PLL SETUP code from stv0367ter_init() into a dedicated function, and also make it possible to configure 58Mhz IC speed at 27MHz Xtal (used on STV0367-based DDB cards/modules in QAM mode). Signed-off-by:
-
Daniel Scheller authored
Move the *ter and *cab st_register tables into a separate header file and additionally organize them via a multidimensional array, allowing to add more tables with differing init values, and also prepare for a base init table which should contain general setup values. Also add a state var to store the table triplet to be used. Also fixes three minor style problems reported by checkpatch. Signed-off-by:
-
Daniel Scheller authored
Change defaults table writing so tables can be of dynamic length without having to keep track of their lengths by adding and evaluating an end marker (reg 0x0000), also move table writing to a dedicated function to remove code duplication. Additionally mark st_register tables const since they're used read-only. Signed-off-by:
-
Daniel Scheller authored
The CPAMP log lines generated in stv0367_ter_check_cpamp() are printed everytime tuning succeeds or fails, quite cluttering the normal kernel log. Use dprintk() instead of printk(KERN_ERR...) so that if the information is needed, it'll be printed when the stv_debug modparam is enabled. Signed-off-by:
-
Daniel Scheller authored
Some hardware and bridges (namely ddbridge) require that tuner access is limited to one concurrent access and wrap i2c gate control with a mutex_lock when attaching frontends. According to vendor information, this is required as concurrent tuner reconfiguration can interfere each other and at worst cause tuning fails or bad reception quality. If the demod driver does gate_ctrl before setting up tuner parameters, and the tuner does another I2C enable, it will deadlock forever when gate_ctrl is wrapped into the mutex_lock. This adds a flag and a conditional before triggering gate_ctrl in the demodulator driver. Signed-off-by:
-
Marek Szyprowski authored
I would like to replace Kyungmin Park, who is no longer interested in maintaining S5P-CEC driver. I have access to various Exynos boards. I also already did some tests of this driver and helped enabling it on various Exynos boards. The driver itself is no longer in staging, so lets fix the path too and add DT bindings file pattern match. Also change the mailing list from ARM generic to Samsung SoC specific to get more attention and easier review in the future. Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Acked-by:
Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
-
Tomasz Figa authored
There are multiple places where arrays or otherwise variable sized buffer are allocated through V4L2 core code, including things like controls, memory pages, staging buffers for ioctls and so on. Such allocations can potentially require an order > 0 allocation from the page allocator, which is not guaranteed to be fulfilled and is likely to fail on a system with severe memory fragmentation (e.g. a system with very long uptime). Since the memory being allocated is intended to be used by the CPU exclusively, we can consider using vmalloc() as a fallback and this is exactly what the recently merged kvmalloc() helpers do. A kmalloc() call is still attempted, even for order > 0 allocations, but it is done with __GFP_NORETRY and __GFP_NOWARN, with expectation of failing if requested memory is not available instantly. Only then the vmalloc() fallback is used. This should give us fast and more reliable allocations even on systems with higher memory pressure and/or more fragmentation, while still retaining the same performance level on systems not suffering from such conditions. While at it, replace explicit array size calculations on changed allocations with kvmalloc_array(). Purposedly not touching videobuf1, as it is deprecated, has only few users remaining and would rather be seen removed instead. Signed-off-by:
Tomasz Figa <tfiga@chromium.org> Acked-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
-
Niklas Söderlund authored
This is a wrapper around the media entity get_fwnode_pad operation. Signed-off-by:
Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Acked-by:
-
Niklas Söderlund authored
The optional operation can be used by entities to report how it maps its fwnode endpoints to media pad numbers. This is useful for devices which require advanced mappings of pads. Signed-off-by:
-
Niklas Söderlund authored
Add a check for v4l2_dev to v4l2_async_notifier_register() as to fail as early as possible since this will fail later in v4l2_async_test_notify(). Signed-off-by:
-
Kieran Bingham authored
The new Renesas R-Car H3 ES2.0 platforms have a new hw version register. Update the driver accordingly, defaulting to the new hw revision, and differentiating the older revision as ES1 Signed-off-by:
Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Gustavo A. R. Silva authored
Remove useless variable assignment in function tc358743_isr(). The value stored in variable _intstatus_ at line 1299 is overwritten at line 1302, just before it can be used. Addresses-Coverity-ID: 1397678 Signed-off-by:
Gustavo A. R. Silva <garsilva@embeddedor.com> Signed-off-by:
Hans Verkuil <hansverk@cisco.com> Signed-off-by:
-
Andrey Utkin authored
Updating my personal email address in solo6x10. Signed-off-by:
Andrey Utkin <andrey.utkin@corp.bluecherry.net> Signed-off-by:
-
Andrey Utkin authored
Anton Sviridenko is now in charge of drivers in Bluecherry. Signed-off-by:
-
Kevin Hilman authored
The davinci VPIF is a single hardware block, but the existing driver is broken up into a common library (vpif.c), output (vpif_display.c) and intput (vpif_capture.c). When migrating to DT, to better model the hardware, and because registers, interrupts, etc. are all common,it was decided to have a single VPIF hardware node[1]. Because davinci uses legacy, non-DT boot on several SoCs still, the platform_drivers need to remain. But they are also needed in DT boot. Since there are no DT nodes for the display/capture parts in DT boot (there is a single node for the parent/common device) we need to create platform_devices somewhere to instantiate the platform_drivers. When VPIF display/capture are needed for a DT boot, the VPIF node will have endpoints defined for its subdevs. Therefore, vpif_probe() checks for the presence of endpoints, and if detected manually creates the platform_devices for the display and capture platform_drivers. [1] Documentation/devicetree/bindings/media/ti,da850-vpif.txt Signed-off-by:
Kevin Hilman <khilman@baylibre.com> Signed-off-by:
-
Christophe JAILLET authored
'call_ptr_memop' can return NULL, so we must test its return value with 'IS_ERR_OR_NULL'. Otherwise, the test 'if (mem_priv)' is meaningless. Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
-
Lucas Stach authored
As long as only one CODA context is running we get alternating device_run() and wait_for_completion() calls, but when more then one CODA context is active, other VDOA slots can be inserted between those calls for one context. Make sure to wait on job completion before running a different context and before destroying the currently active context. Signed-off-by:
Lucas Stach <l.stach@pengutronix.de> Reviewed-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
-
Lucas Stach authored
This implements a simple handler for the case where decode did not finish sucessfully. This might be helpful during normal streaming, but for now it only handles the case where the context would deadlock with userspace, i.e. userspace issued DEC_CMD_STOP and waits for EOS, but after the failed decode run we would hold the context and wait for userspace to queue more buffers. Signed-off-by:
-
Lucas Stach authored
The mvcol buffer needs to be placed behind the chroma plane(s), so use the real offset including any required rounding. Signed-off-by:
-
Stanimir Varbanov authored
This makes firmware name and path part of venus_resources structure and initialize it properly depending on the SoC and firmware version. Signed-off-by:
Stanimir Varbanov <stanimir.varbanov@linaro.org> Signed-off-by:
-
Stanimir Varbanov authored
This adds support for V4L2_CID_MIN_BUFFERS_FOR_CAPTURE get control in venus decoder, it is usable in case when the userspace wants to know minimum capture buffers before calling request_buf for capture queue in mem2mem drivers. Also this will fix an issue found gstreamer v4l2videodec element, i.e. the video decoder element cannot continue because the buffers are insufficient. Signed-off-by:
-
Stanimir Varbanov authored
This fixes the following compile error ocured when building with gcc7: drivers/media/platform/qcom/venus/venc.c:1150 venc_close() error: dereferencing freed memory 'inst' by moving kfree as a last call. Signed-off-by:
-
Stanimir Varbanov authored
This fixes the following compile error ocured when building with gcc7: drivers/media/platform/qcom/venus/vdec.c:1022 vdec_close() error: dereferencing freed memory 'inst' by moving kfree as a last call. Signed-off-by:
-
Stanimir Varbanov authored
This fixes a warning found when building with gcc7: drivers/media/platform/qcom/venus/hfi_msgs.c:465:40: warning: variable 'domain' set but not used [-Wunused-but-set-variable] u32 rem_bytes, num_props, codecs = 0, domain = 0; ^~~~~~ drivers/media/platform/qcom/venus/hfi_msgs.c:465:28: warning: variable 'codecs' set but not used [-Wunused-but-set-variable] u32 rem_bytes, num_props, codecs = 0, domain = 0; The warning is avoided by deleting the variables declaration. Signed-off-by: -
Stanimir Varbanov authored
This fixes a warning found when building with gcc7: drivers/media/platform/qcom/venus/hfi_venus.c:998 venus_isr_thread() warn: variable dereferenced before check 'hdev' (see line 994) Signed-off-by:
-
Stanimir Varbanov authored
This fixes a warning found when building the driver with gcc7: drivers/media/platform/qcom/venus/helpers.c:157 load_per_instance() warn: variable dereferenced before check 'inst' (see line 153) Signed-off-by:
-
Stanimir Varbanov authored
This fixes a warning found when building the driver with gcc7: drivers/media/platform/qcom/venus/hfi_cmds.c:415 pkt_session_set_property_1x() warn: variable dereferenced before check 'pkt' (see line 412) drivers/media/platform/qcom/venus/hfi_cmds.c:1177 pkt_session_set_property_3xx() warn: variable dereferenced before check 'pkt' (see line 1174) Signed-off-by:
-
Stanimir Varbanov authored
This fixed a warning when build driver with gcc7: drivers/media/platform/qcom/venus/hfi.c:171 hfi_core_ping() warn: inconsistent returns 'mutex:&core->lock'. Locked on: line 159 Unlocked on: line 171 Signed-off-by:
-
Stanimir Varbanov authored
This adds Venus driver Makefile and changes v4l2 platform Makefile/Kconfig in order to enable building of the driver. Note that in this initial version the COMPILE_TEST-ing is not supported because the drivers specific to ARM builds are still in process of enabling the aforementioned compile testing. Once that disadvantage is fixed the Venus driver compile testing will be possible with follow-up changes. Signed-off-by:
-
Stanimir Varbanov authored
Here is the implementation of Venus video accelerator low-level functionality. It contanins code which setup the registers and startup uthe processor, allocate and manipulates with the shared memory used for sending commands and receiving messages. Signed-off-by:
-
Stanimir Varbanov authored
This is the implementation of HFI. It is charged with the responsibility to comunicate with the firmware through an interface commands and messages. - hfi.c has interface functions used by the core, decoder and encoder parts to comunicate with the firmware. For example there are functions for session and core initialisation. - hfi_cmds has packetization operations which preparing packets to be send from host to firmware. - hfi_msgs takes care of messages sent from firmware to the host. Signed-off-by:
-
Stanimir Varbanov authored
This adds encoder part of the driver plus encoder controls. Signed-off-by:
-
Stanimir Varbanov authored
This consists of video decoder implementation plus decoder controls. Signed-off-by:
-
Stanimir Varbanov authored
* core.c has implemented the platform driver methods, file operations and v4l2 registration. * helpers.c has implemented common helper functions for: - buffer management - vb2_ops and functions for format propagation, - functions for allocating and freeing buffers for internal usage. The buffer parameters describing internal buffers depends on current format, resolution and codec. - functions for calculation of current load of the hardware. Depending on the count of instances and resolutions it selects the best clock rate for the video core. * firmware loader Signed-off-by:
-
Stanimir Varbanov authored
Add an entry for Venus video encoder/decoder accelerator driver. Signed-off-by:
-
Stanimir Varbanov authored
Add binding document for Venus video encoder/decoder driver Cc: Rob Herring <robh+dt@kernel.org> Cc: devicetree@vger.kernel.org Acked-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
