Florian Fainelli says:

====================
net: phy: phy_interface_is_rgmii helper

As you suggested, here is the helper function to avoid missing some RGMII
interface checks. Had to wait for net to be merged in net-next to avoid
submitting the same patch/commit.

Dan, you might want to rebase your dp83867 submission to use that helper
when you this patchset gets merged into net-next, thanks!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Update all open-coded tests for all 4 PHY_INTERFACE_MODE_RGMII* values
to use the newly introduced helper: phy_interface_is_rgmii.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RGMII interfaces come in 4 different flavors that the PHY library needs
to care about: regular RGMII (no delays), RGMII with either RX or TX
delay, and both. In order to avoid errors of checking only for one type
of RGMII interface and miss the 3 others, introduce a convenience
function which tests for all values.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We used to get this indirectly I supposed, but no longer do.

Either way, an explicit include should have been done in the
first place.

   net/ipv4/fib_trie.c: In function '__node_free_rcu':
>> net/ipv4/fib_trie.c:293:3: error: implicit declaration of function 'vfree' [-Werror=implicit-function-declaration]
      vfree(n);
      ^
   net/ipv4/fib_trie.c: In function 'tnode_alloc':
>> net/ipv4/fib_trie.c:312:3: error: implicit declaration of function 'vzalloc' [-Werror=implicit-function-declaration]
      return vzalloc(size);
      ^
>> net/ipv4/fib_trie.c:312:3: warning: return makes pointer from integer without a cast
   cc1: some warnings being treated as errors
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

By making sure sk->sk_gso_max_segs minimal value is one,
and sysctl_tcp_min_tso_segs minimal value is one as well,
tcp_tso_autosize() will return a non zero value.

We can then revert 843925f3
("tcp: Do not apply TSO segment limit to non-TSO packets")
and save few cpu cycles in fast path.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

If tcp ehash table is constrained to a very small number of buckets
(eg boot parameter thash_entries=128), then we can crash if spinlock
array has more entries.

While we are at it, un-inline inet_ehash_locks_alloc() and make
following changes :

- Budget 2 cache lines per cpu worth of 'spinlocks'
- Try to kmalloc() the array to avoid extra TLB pressure.
  (Most servers at Google allocate 8192 bytes for this hash table)
- Get rid of various #ifdef
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit dd3f9e70
("tipc: add packet sequence number at instant of transmission") we
made a change with the consequence that packets in the link backlog
queue don't contain valid sequence numbers.

However, when we create a link protocol message, we still use the
sequence number of the first packet in the backlog, if there is any,
as "next_sent" indicator in the message. This may entail unnecessary
retransissions or stale packet transmission when there is very low
traffic on the link.

This commit fixes this issue by only using the current value of
tipc_link::snd_nxt as indicator.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

make C=2 CF=-D__CHECK_ENDIAN__ net/core/utils.o
...
net/core/utils.c:307:72: warning: incorrect type in argument 2 (different base types)
net/core/utils.c:307:72:    expected restricted __wsum [usertype] addend
net/core/utils.c:307:72:    got restricted __be32 [usertype] from
net/core/utils.c:308:34: warning: incorrect type in argument 2 (different base types)
net/core/utils.c:308:34:    expected restricted __wsum [usertype] addend
net/core/utils.c:308:34:    got restricted __be32 [usertype] to
net/core/utils.c:310:70: warning: incorrect type in argument 2 (different base types)
net/core/utils.c:310:70:    expected restricted __wsum [usertype] addend
net/core/utils.c:310:70:    got restricted __be32 [usertype] from
net/core/utils.c:310:77: warning: incorrect type in argument 2 (different base types)
net/core/utils.c:310:77:    expected restricted __wsum [usertype] addend
net/core/utils.c:310:77:    got restricted __be32 [usertype] to
net/core/utils.c:312:72: warning: incorrect type in argument 2 (different base types)
net/core/utils.c:312:72:    expected restricted __wsum [usertype] addend
net/core/utils.c:312:72:    got restricted __be32 [usertype] from
net/core/utils.c:313:35: warning: incorrect type in argument 2 (different base types)
net/core/utils.c:313:35:    expected restricted __wsum [usertype] addend
net/core/utils.c:313:35:    got restricted __be32 [usertype] to

Note we can use csum_replace4() helper

Fixes: 58e3cac5 ("net: optimise inet_proto_csum_replace4()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

make C=2 CF=-D__CHECK_ENDIAN__ net/core/secure_seq.o
net/core/secure_seq.c:157:50: warning: restricted __be32 degrades to
integer
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check in fdb_add_entry() if the source port should learn, similar
check is used in br_fdb_update.
Note that new fdb entries which are added manually or
as local ones are still permitted.
This patch has been tested by running traffic via a bridge port and
switching the port's state, also by manually adding/removing entries
from the bridge's fdb.
Signed-off-by: Wilson Kok <wkok@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/core/pktgen.c:2672:43: warning: incorrect type in assignment (different base types)
net/core/pktgen.c:2672:43:    expected unsigned short [unsigned] [short] [usertype] <noident>
net/core/pktgen.c:2672:43:    got restricted __be16 [usertype] protocol

Let's use proper struct ethhdr instead of hard coding everything.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6_select_ident() returns a 32bit value in network order.

Fixes: 286c2349 ("ipv6: Clean up ipv6_select_ident() and ip6_fragment()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Richard Cochran says:

====================
cpsw cleanups

While working on an out-of-tree customization, I noticed a few minor
problems in the cpsw code.  This series cleans up the issues I found.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The function, cpsw_intr_disable, already calls cpdma_ctlr_int_ctrl.  There
is no need to disable the dma interrupts twice.  This patch removes the
extra calls.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function, cpsw_intr_enable, already calls cpdma_ctlr_int_ctrl.  There
is no need to enable the dma interrupts twice.  This patch removes the
extra call.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The funtions, cpsw_ale_flush and cpsw_ale_set_ageout, have never been used
since they were first introduced.  This patch removes the dead code.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Having the breaks too far to the left makes parsing the dense switch/case
block unnecessarily harder.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simon Horman says:

====================
rocker: unused parameter and const cleanups

This series provides some minor though verbose cleanup of rocker.

The second patch depends on the first though it could be rebased.

I had previously asked for v2 to be put on hold while some bugs I had found
in the rocker driver were shaken out. That has now happened and the bugs
turned out to be unrelated.  Accordingly I am reposting the series.

* Changes v2 -> v3
  - Rebase and update for new variables and parameters that may be const

* Changes v1 -> v2
  - Found quite a few more variables and parameters to make const
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Mark parameters and local variables as const where possible.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove unused rocker_port parameter from rocker_port_kfree.
Also remove the rocker_port parameter from callers of rocker_port_kfree
where the parameter it is now unused.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

API compliance scanning with coccinelle flagged:
./net/irda/timer.c:63:35-37: use of msecs_to_jiffies probably perferable

Converting milliseconds to jiffies by "val * HZ / 1000" technically
is not a clean solution as it does not handle all corner cases correctly.
By changing the conversion to use msecs_to_jiffies(val) conversion is
correct in all cases. Further the () around the arithmetic expression
was dropped.

Patch was compile tested for x86_64_defconfig + CONFIG_IRDA=m

Patch is against 4.1-rc4 (localversion-next is -next-20150522)
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

These two uses seem to have had carriage returns removed.
Make these entries like all the others in this file.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

API compliance scanning with coccinelle flagged:

Converting milliseconds to jiffies by "val * HZ / 1000" is technically
is not a clean solution as it does not handle all corner cases correctly.
By changing the conversion to use msecs_to_jiffies(val) conversion is
correct in all cases.

in the current code:
  mod_timer(&self->rx_defer_timer, jiffies + (10 * HZ / 1000));
for HZ < 100 (e.g. CONFIG_HZ == 64|32 in alpha) this effectively results
in no delay at all.

Patch was compile tested for x86_64_defconfig (implies CONFIG_USB_IRDA=m)

Patch is against 4.1-rc4 (localversion-next is -next-20150522)
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Network managers like netifd (used in OpenWRT for instance) try to
configure interface options after creation but before setting the
interface up.

Unfortunately the sysfs / bridge currently only allows to configure the
hash_max and multicast_router options when the bridge interface is up.
But since br_multicast_init() doesn't start any timers and only sets
default values and initializes timers it should be save to reconfigure
the default values after that, before things actually get active after
the bridge is set up.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>

since commit 6aafeef0 ("netfilter: push reasm skb through instead of
original frag skbs") we will end up sometimes re-fragmenting skbs
that we've reassembled.

ipv6 defrag preserves the original skbs using the skb frag list, i.e. as long
as the skb frag list is preserved there is no problem since we keep
original geometry of fragments intact.

However, in the rare case where the frag list is munged or skb
is linearized, we might send larger fragments than what we originally
received.

A router in the path might then send packet-too-big errors even if
sender never sent fragments exceeding the reported mtu:

mtu 1500 - 1500:1400 - 1400:1280 - 1280
     A         R1         R2        B

1 - A sends to B, fragment size 1400
2 - R2 sends pkttoobig error for 1280
3 - A sends to B, fragment size 1280
4 - R2 sends pkttoobig error for 1280 again because it sees fragments of size 1400.

make sure ip6_fragment always caps MTU at largest packet size seen
when defragmented skb is forwarded.
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The variable irq_coalesce is bool type.
So assign the value true instead of 1.
Signed-off-by: Shailendra Verma <shailendra.capricorn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The variable separate_tx_rx_irq is bool type so assigning true
instead of 1.
Signed-off-by: Shailendra Verma <shailendra.capricorn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Martin KaFai Lau says:

====================
ipv6: Only create RTF_CACHE route after encountering pmtu exception

v4 -> v5:
- Patch 1 is new. Clean up the ipv6_select_ident() and ip6_fragment().

- Further simplify the newly added rt6_get_pcpu_route().  If there is a
  'prev' after cmpxchg, return prev instead of the newly created percpu
  clone.

v3 -> v4:
- Patch 8 is new. It keeps track of the DST_NOCACHE routes in a list to handle
  the iface down/unregister event.

- Remove rcu from the newly added rt6i_pcpu variable.  It is not needed
  because it has already been protected by the existing reader/writer lock.

- Thanks to 'Julian Anastasov <ja@ssi.bg>' for testing the FLOWI_FLAG_KNOWN_NH
  patches.

v2 -> v3:
- Patch 5 to 7 are new.  They take care of cases where the daddr in
  skb is not the one used to do the route look-up.  There is also
  related changes to rt6_nexthop() since v2 which is in patch 2/9.
  Thanks to 'Julian Anastasov <ja@ssi.bg>' for pointing it out.

- Fix a few problems in __ip6_rt_update_pmtu(), like setting the expire
  and mtu before inserting to the tree and don't do dst_destroy() after
  tree insertion failure.  Also update the rt6i_pmtu in fib6_add_rt2node().
  Thanks to 'Steffen Klassert <steffen.klassert@secunet.com>' for pointing
  it out.

- Merge ip6_pmtu_rt_cache_alloc() into ip6_rt_cache_alloc().

v1 -> v2:
- Move the /128 route bug fixes to another series (accepted).
- Create a function for checking (rt6i_flags & (RTF_NONEXTHOP | RTF_GATEWAY)).
- Avoid shuffling the skb network_header.  Instead, change the function
  signature to take iph instead of skb.

- Many Thanks to 'Hannes Frederic Sowa <hannes@stressinduktion.org>' on
  reviewing v1 and v2 and giving advice.

--Martin

~~~ start: v1 compose message (with the out-dated parts removed) ~~~

This series is to avoid creating a RTF_CACHE route whenever we are consulting
the fib6 tree with a new destination.  Instead, only create RTF_CACHE route
when we see a pmtu exception.

Out of all ipv6 RTF_CACHE routes that are created, the percentage that has a
different mtu is very small. In one of our end-user facing proxy server,
only 1k out of 80k RTF_CACHE routes have a smaller MTU.  For our DC
traffic, there is no mtu exception.

A large fib6 tree has problems like, 'ip -6 r show' takes a long time.
gc may kick in too often.  Also, when a service has restarted and a lot
of new TCP conn requests come in, it creates pressure on the tree by inserting
a lot of RTF_CACHE in a short time and it currently requires a write lock
to do that.

The first few patches are prep works to remove assumption that the
returned rt is always RTF_CACHE.

The patch 'ipv6: Only create RTF_CACHE routes after encountering pmtu exception'
do the lazy RTF_CACHE route creation.

The following patches added percpu rt to compensate the performance loss after
doing the RTF_CACHE lazy creation.

Here is some numbers of the udpflood test.  The udpflood has been
slightly modified to have a time limit instead of count limit.

A /64 via gateway route is used for the test. Each udpflood uses 10000 dst
addresses.  The dst addresses of different udpflood processes do not overlap
with each other.

1                    16M                          15M
10                   61M                          61M
20                   65M                          62M
40                   88M                          83M

~~~ end: v1 compose message ~~~
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

After the patch
'ipv6: Only create RTF_CACHE routes after encountering pmtu exception',
we need to compensate the performance hit (bouncing dst->__refcnt).
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch breaks up ip6_rt_copy() into ip6_rt_copy_init() and
ip6_rt_cache_alloc().

In the later patch, we need to create a percpu rt6_info copy. Hence,
refactor the common rt6_info init codes to ip6_rt_copy_init().
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch keeps track of the DST_NOCACHE routes in a list and replaces its
dev with loopback during the iface down/unregister event.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch always creates RTF_CACHE clone with DST_NOCACHE
when FLOWI_FLAG_KNOWN_NH is set so that the rt6i_dst is set to
the fl6->daddr.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Tested-by: Julian Anastasov <ja@ssi.bg>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The neighbor look-up used to depend on the rt6i_gateway (if
there is a gateway) or the rt6i_dst (if it is a RTF_CACHE clone)
as the nexthop address.  Note that rt6i_dst is set to fl6->daddr
for the RTF_CACHE clone where fl6->daddr is the one used to do
the route look-up.

Now, we only create RTF_CACHE clone after encountering exception.
When doing the neighbor look-up with a route that is neither a gateway
nor a RTF_CACHE clone, the daddr in skb will be used as the nexthop.

In some cases, the daddr in skb is not the one used to do
the route look-up.  One example is in ip_vs_dr_xmit_v6() where the
real nexthop server address is different from the one in the skb.

This patch is going to follow the IPv4 approach and ask the
ip6_pol_route() callers to set the FLOWI_FLAG_KNOWN_NH properly.

In the next patch, ip6_pol_route() will honor the FLOWI_FLAG_KNOWN_NH
and create a RTF_CACHE clone.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Tested-by: Julian Anastasov <ja@ssi.bg>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of doing the rt6->rt6i_node check whenever we need
to get the route's cookie.  Refactor it into rt6_get_cookie().
It is a prep work to handle FLOWI_FLAG_KNOWN_NH and also
percpu rt6_info later.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch creates a RTF_CACHE routes only after encountering a pmtu
exception.

After ip6_rt_update_pmtu() has inserted the RTF_CACHE route to the fib6
tree, the rt->rt6i_node->fn_sernum is bumped which will fail the
ip6_dst_check() and trigger a relookup.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

A prep work for creating RTF_CACHE on exception only.  After this
patch, the same condition (rt->rt6i_flags & (RTF_NONEXTHOP | RTF_GATEWAY))
is checked twice. This redundancy will be removed in the later patch.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

When creating a RTF_CACHE route, RTF_ANYCAST is set based on rt6i_dst.
Also, rt6i_gateway is always set to the nexthop while the nexthop
could be a gateway or the rt6i_dst.addr.

After removing the rt6i_dst and rt6i_src dependency in the last patch,
we also need to stop the caller from depending on rt6i_gateway and
RTF_ANYCAST.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes the assumptions that the returned rt is always
a RTF_CACHE entry with the rt6i_dst and rt6i_src containing the
destination and source address.  The dst and src can be recovered from
the calling site.

We may consider to rename (rt6i_dst, rt6i_src) to
(rt6i_key_dst, rt6i_key_src) later.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch changes the ipv6_select_ident() signature to return a
fragment id instead of taking a whole frag_hdr as a param to
only set the frag_hdr->identification.

It also cleans up ip6_fragment() to obtain the fragment id at the
beginning instead of using multiple "if" later to check fragment id
has been generated or not.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for flashing 10GBaseT adapter with BCM 84834 PHY and
Aquantia AQ1202 PHY.

Updating of the PHY firmware must happen before the INITIALIZE_CMD.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>