- 09 Sep, 2011 6 commits
-
-
Oren Weil authored
adding watchdog ping to send ping/heartbeat to the the AMT watchdog client. in addition removing the heartbeat sending from the driver timers function. Signed-off-by:
Oren Weil <oren.jer.weil@intel.com> Acked-by:
Tomas Winkler <tomas.winkler@intel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Oren Weil authored
adding start and stop function. start - check if AMT wd client is connected, which is been connected on driver load. stop - send stop command to AMT wd. Signed-off-by:
-
Oren Weil authored
Adding kernel watchdog interface (/dev/watchdog) to the MEI Driver to support AMT Watchdog feature. This patch and the following one will replace MEI Driver self management of the AMT watchdog with the standard kernel watchdog interface. Signed-off-by:
-
Oren Weil authored
Signed-off-by:
-
Oren Weil authored
AMTHI need to be initialized after WD Client was initialized, moving the AMTHI outside of the WD initialization function. in order to remove the coupling between the initialization of those clients. AMTHI is getting initialized (getting connected to the FW feature/client) in two ways: 1) if mei driver fails to send connect message to watchdog client (WD initialization), then immediately the AMTHI client getting initialized right after the watchdog initialization function. 2) if Watchdog client success to send connect message to watchdog client, then only after the driver is getting the connect response message the AMTHI client is getting initialized Signed-off-by: -
Manohar Vanga authored
Change the static array of 'struct device''s in struct vme_bridge to instead use an array of pointers. This is in accordance with the requirement that all kobjects be dynamically allocated (see Documentation/kobject.txt) and never be statically allocated. Signed-off-by:
Manohar Vanga <manohar.vanga@cern.ch> Acked-by:
Martyn Welch <martyn.welch@ge.com> Signed-off-by:
-
- 07 Sep, 2011 21 commits
-
-
Ali Bahar authored
The ioctl handlers were frequently returning -1 upon failure. Most of these have now been changed to proper errno macros. The few remaining ones have been left untouched because either the handler is not called (and so cannot be tested), or the function never fails (and so cannot be system-tested), or requires new code to distinguish its failures. Signed-off-by:
Ali Bahar <ali@internetDog.org> Cc: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
-
Larry Finger authored
The frame buffers allocated in _r8712_init_recv_priv() are not tracked by kmemleak, but they are freed when the driver is unloaded. To help find any real leaks, these false positives are annotated for kmemleak. Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
-
Ali Bahar authored
Tx Aggregation (CONFIG_R8712_TX_AGGR, known as CONFIG_USB_TX_AGGR in the Realtek tarball) is now added. However, its tests have not been successful! The default in the Realtek tarball is to not build it -- and the Release Notes does not seem to list this as a feature. I have tested the driver with and without this feature; the former does not successfully associate when WPA2 is used. Signed-off-by:
-
Ali Bahar authored
In r8712_generate_ie(), HT check is no longer done. Removed r8712_add_ht_addt_info(). Changes to defragmentation handling, and queue selection. Get TSSI command. Added an Ad-Hoc check to is_desired_network() r8712_ind_disconnect() now checks for Linked state. r8712_xmit_bh() now schedules an xmit tasklet. Signed-off-by:
-
Ali Bahar authored
passive_mode added to private ioctls. New private ioctls added for RSSI, link speed, mac address, scan type, and DCE-D. In r8711_wx_get_scan(), we now sleep only 100 times, instead of 1000. In r8711_wx_set_essid(), added a check for Ad-Hoc state. In r8711_wx_get_rate(), added a check for RTL8712_RF_2T2R RF type. Added Set chplan. In r871x_get_wireless_stats(), updated the mechanism for displaying link quality. Added SetDIG and SetRA commands. r8712_joinbss_cmd() no longer checks for Ad-Hoc mode. Signed-off-by:
-
Ali Bahar authored
Removed unnecessary casts in kfree calls. A few new types, defines and prototypes. Signed-off-by:
-
Ali Bahar authored
In transmit path, r8712_free_xmitframe(), the pkt pointer is now NULLed _within_ the spin lock. Signed-off-by:
-
Ali Bahar authored
Rework efuse data handling. Signed-off-by:
-
Ali Bahar authored
Refactor the TX code to prepare for aggregation. Signed-off-by:
-
Ali Bahar authored
translate_scan() now uses the stack for some variables, instead of mallocing. Signed-off-by:
-
Ali Bahar authored
stop_drv_timers() is now done in r871xu_dev_remove(), not netdev_close(). Signed-off-by:
-
Ali Bahar authored
The call to oid_rt_pro_set_power_tracking_hdl() is no longer available. The function's definition remains, though it is currently unused. Signed-off-by:
-
Ali Bahar authored
recv_frame.mem mp_xmit_frame.mem mp_xmit_packet.mem were not used, and so are now removed. Signed-off-by:
-
Ali Bahar authored
These are the new include directives for header files. The following were (somehow!) not explicity in Realtek's, but proved necessary: "linux/usb.h" is needed for usb_alloc_urb(); "linux/interrupt.h" is needed for tasklet_struct. It was often a nested include. Signed-off-by:
-
Ali Bahar authored
Removed the redundant NULL check in LedControl871x. As noted by Dan Carpenter, the address of a stack variable is never NULL. Signed-off-by:
-
Ali Bahar authored
MSECS was never used in this driver. So removed. Signed-off-by:
-
Ali Bahar authored
Replaced (Realtek's) _usb_submit_urb by (linux's own) usb_submit_urb. Signed-off-by:
-
Ali Bahar authored
Replaced (Realtek's) _usb_alloc_urb by (linux's own) usb_alloc_urb. Signed-off-by:
-
Ali Bahar authored
Replaced (Realtek's) os_free_netdev by (linux's own) free_netdev. Signed-off-by:
-
Ali Bahar authored
Renamed _netdev_priv to netdev_priv. Signed-off-by:
-
Ali Bahar authored
Only copyright banners have been added to these files. No functional changes. Signed-off-by:
-
- 06 Sep, 2011 13 commits
-
-
Jerome Marchand authored
When the allocation of zram->table fails, we set zram->disksize to zero to prevent accessing the unallocated table entries during cleanup. However, we currently don't take this precaution when the initialization fails earlier. Signed-off-by:
Jerome Marchand <jmarchan@redhat.com> Signed-off-by:
-
Jerome Marchand authored
Currently init_lock only prevents concurrent execution of zram_init_device() and zram_reset_device() but not zram_make_request() nor sysfs store functions. This patch changes init_lock into a rw_semaphore. A write lock is taken by init, reset and store functions, a read lock is taken by zram_make_request(). Also, avoids to release the lock before calling __zram_reset_device() for cleaning after a failed init, thus preventing any concurrent task to see an inconsistent state of zram. Signed-off-by:
-
Mark Einon authored
I believe that the driver is up to date with the latest network driver changes, so removing this line from the TODO to see if anyone else disagrees. Also all useless typecasts are now dead. Signed-off-by:
Mark Einon <mark.einon@gmail.com> Signed-off-by:
-
Mark Einon authored
The ai_force settings were used to set the ethernet speed and duplex manually. This is now being done by the phy_device, so remove. Signed-off-by:
-
Mark Einon authored
This structure is no longer used, and references registers defined in mii.h and other parts of et1310_phy.h Signed-off-by:
-
Mark Einon authored
Replaced et131x_phy.c magic numbers specifying registers and their values with defines, defined in et131x_phy.h Signed-off-by:
-
Mark Einon authored
The VMI_* set of register defines are not used, and duplicate the set of PHY_* registers from the same file, which are used - hence removing. Signed-off-by:
-
Mark Einon authored
cached_mask_value is only ever assigned, never read. Remove it. Signed-off-by:
-
Mark Einon authored
registry_rx_mem_end is not referenced anywhere in the driver. Signed-off-by:
-
Mark Einon authored
As et131x_adjust_link is called from the phydev in response to a netif_carrier_[on|off], and is the only caller of et131x_mii_check, we don't need to call netif_carrier_[on|off] again. Signed-off-by:
-
Mark Einon authored
The PHY interrupt is now handled by the phy_device, and the equivalent code is present in et131x_adjust_link, called from the phy_device when needed. Signed-off-by:
-
Mark Einon authored
adapter->speed_duplex was never referenced. adapter->registry_phy_coma was always set to zero, even in the vendor driver. Removing all member references and associated dead code. Signed-off-by:
-
Mark Einon authored
The phy device keeps a note of the duplex mode, so use that value instead of duplex mode. Also use the phydev defines for duplex modes, and remove the driver private ones. Signed-off-by:
-
