- 31 Jan, 2019 37 commits
-
-
Eugeniy Paltsev authored
commit 3affbf0e upstream. So far we've mapped branches to "ijmp" which also counts conditional branches NOT taken. This makes us different from other architectures such as ARM which seem to be counting only taken branches. So use "ijmptak" hardware condition which only counts (all jump instructions that are taken) 'ijmptak' event is available on both ARCompact and ARCv2 ISA based cores. Signed-off-by:
Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Cc: stable@vger.kernel.org Signed-off-by:
Vineet Gupta <vgupta@synopsys.com> [vgupta: reworked changelog] Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Eugeniy Paltsev authored
commit a3010a04 upstream. In setup_arch_memory we reserve the memory area wherein the kernel is located. Current implementation may reserve more memory than it actually required in case of CONFIG_LINUX_LINK_BASE is not equal to CONFIG_LINUX_RAM_BASE. This happens because we calculate start of the reserved region relatively to the CONFIG_LINUX_RAM_BASE and end of the region relatively to the CONFIG_LINUX_RAM_BASE. For example in case of HSDK board we wasted 256MiB of physical memory: ------------------->8------------------------------ Memory: 770416K/1048576K available (5496K kernel code, 240K rwdata, 1064K rodata, 2200K init, 275K bss, 278160K reserved, 0K cma-reserved) ------------------->8------------------------------ Fix that. Fixes: 9ed68785 ("ARC: mm: Decouple RAM base address from kernel link addr") Cc: stable@vger.kernel.org #4.14+ Signed-off-by:
-
Eugeniy Paltsev authored
commit e6a72b7d upstream. ARCv2 optimized memset uses PREFETCHW instruction for prefetching the next cache line but doesn't ensure that the line is not past the end of the buffer. PRETECHW changes the line ownership and marks it dirty, which can cause issues in SMP config when next line was already owned by other core. Fix the issue by avoiding the PREFETCHW Some more details: The current code has 3 logical loops (ignroing the unaligned part) (a) Big loop for doing aligned 64 bytes per iteration with PREALLOC (b) Loop for 32 x 2 bytes with PREFETCHW (c) any left over bytes loop (a) was already eliding the last 64 bytes, so PREALLOC was safe. The fix was removing PREFETCW from (b). Another potential issue (applicable to configs with 32 or 128 byte L1 cache line) is that PREALLOC assumes 64 byte cache line and may not do the right thing specially for 32b. While it would be easy to adapt, there are no known configs with those lie sizes, so for now, just compile out PREALLOC in such cases. Signed-off-by:
-
Anthony Wong authored
commit 69939038 upstream. Support speaker and mic mute LEDs on HP ProBook 470 G5. BugLink: https://bugs.launchpad.net/bugs/1811254Signed-off-by:
Anthony Wong <anthony.wong@canonical.com> Cc: <stable@vger.kernel.org> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Kailang Yang authored
commit 82aa0d7e upstream. Fix typo for model alc255-dell1 to alc225-dell1. Enable headset mode support for new WYSE NB platform. Fixes: a26d96c7 ("ALSA: hda/realtek - Comprehensive model list for ALC259 & co") Signed-off-by:
Kailang Yang <kailang@realtek.com> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Tetsuo Handa authored
commit 125892ed upstream. Commit 4d97f7d5 ("inotify: Add flag IN_MASK_CREATE for inotify_add_watch()") forgot to call fdput() before bailing out. Fixes: 4d97f7d5 ("inotify: Add flag IN_MASK_CREATE for inotify_add_watch()") CC: stable@vger.kernel.org Signed-off-by:
Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Reviewed-by:
Amir Goldstein <amir73il@gmail.com> Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
-
Dinh Nguyen authored
commit b488517b upstream. The fixed clocks in the DTS file have a hyphen, but the clock driver has the fixed clocks using underbar. Thus the clock driver cannot detect the other fixed clocks correctly. Change the fixed clock names to a hyphen. Fixes: 07afb8db ("clk: socfpga: stratix10: add clock driver for Stratix10 platform") Cc: linux-stable@vger.kernel.org Signed-off-by:
Dinh Nguyen <dinguyen@kernel.org> Signed-off-by:
Stephen Boyd <sboyd@kernel.org> Signed-off-by:
-
Dinh Nguyen authored
commit c0a636e4 upstream. The main PLL calculation has a mistake. We should be using the multiplying the VCO frequency, not the parent clock frequency. Fixes: 07afb8db ("clk: socfpga: stratix10: add clock driver for Stratix10 platform") Cc: linux-stable@vger.kernel.org Signed-off-by:
-
b-ak authored
commit 667e9334 upstream. During the bootup of the kernel, the DAPM bias level is in the OFF state. As soon as the DAPM framework kicks in it pushes the codec into STANDBY state. The probe function doesn't prepare the clock, and STANDBY state does a clk_disable_unprepare() without checking the previous state. This leads to an OOPS. Not transitioning from an OFF state to the STANDBY state fixes the problem. Signed-off-by:
b-ak <anur.bhargav@gmail.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by:
-
Gustavo A. R. Silva authored
commit 060d0bf4 upstream. There is a potential NULL pointer dereference in case devm_kzalloc() fails and returns NULL. Fix this by adding a NULL check on rt5514_dsp. This issue was detected with the help of Coccinelle. Fixes: 6eebf35b ("ASoC: rt5514: add rt5514 SPI driver") Cc: stable@vger.kernel.org Signed-off-by:
Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by:
-
Kangjie Lu authored
commit 44fabd8c upstream. snd_pcm_lib_malloc_pages() may fail, so let's check its status and return its error code upstream. Signed-off-by:
Kangjie Lu <kjlu@umn.edu> Acked-by:
Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by:
-
Yan, Zheng authored
commit d95e674c upstream. snap realm and corresponding inode have pointers to each other. The two pointer should get clear at the same time. Otherwise, snap realm's pointer may reference freed inode. Cc: stable@vger.kernel.org # 4.17+ Signed-off-by:
"Yan, Zheng" <zyan@redhat.com> Reviewed-by:
Luis Henriques <lhenriques@suse.com> Signed-off-by:
Ilya Dryomov <idryomov@gmail.com> Signed-off-by:
-
Charles Yeh authored
commit 4dcf9ddc upstream. Add new PID to support PL2303TB (TYPE_HX) Signed-off-by:
Charles Yeh <charlesyeh522@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Max Schulze authored
commit b81c2c33 upstream. Add new Motorola Tetra device id for Motorola Solutions TETRA PEI device T: Bus=02 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=0cad ProdID=9016 Rev=24.16 S: Manufacturer=Motorola Solutions, Inc. S: Product=TETRA PEI interface C: #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=usb_serial_simple I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=usb_serial_simple Signed-off-by:
Max Schulze <max.schulze@posteo.de> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Christian Lamparter authored
commit 91f7d2e8 upstream. The patch "usb: simplify usbport trigger" together with "leds: triggers: add device attribute support" caused an regression for the usbport trigger. it will no longer enumerate any active usb hub ports under the "ports" directory in the sysfs class directory, if the usb host drivers are fully initialized before the usbport trigger was loaded. The reason is that the usbport driver tries to register the sysfs entries during the activate() callback. And this will fail with -2 / ENOENT because the patch "leds: triggers: add device attribute support" made it so that the sysfs "ports" group was only being added after the activate() callback succeeded. This version of the patch reverts parts of the "usb: simplify usbport trigger" patch and restores usbport trigger's functionality. Fixes: 6f7b0bad ("usb: simplify usbport trigger") Signed-off-by:
Christian Lamparter <chunkeey@gmail.com> Cc: stable <stable@vger.kernel.org> Acked-by:
Jacek Anaszewski <jacek.anaszewski@gmail.com> Signed-off-by:
-
Tomas Winkler authored
commit f7ee8ead upstream. Add the Denverton innovation engine (IE) device ids. The IE is an ME-like device which provides HW security offloading. Cc: <stable@vger.kernel.org> Signed-off-by:
Tomas Winkler <tomas.winkler@intel.com> Signed-off-by:
Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by:
-
Alexander Usyskin authored
commit 173436ba upstream. The LBG server platform sports DMA support. Cc: <stable@vger.kernel.org> #v5.0+ Signed-off-by:
-
Willem de Bruijn authored
[ Upstream commit 13d7f463 ] TCP transmission with MSG_ZEROCOPY fails if the peer closes its end of the connection and so transitions this socket to CLOSE_WAIT state. Transmission in close wait state is acceptable. Other similar tests in the stack (e.g., in FastOpen) accept both states. Relax this test, too. Link: https://www.mail-archive.com/netdev@vger.kernel.org/msg276886.html Link: https://www.mail-archive.com/netdev@vger.kernel.org/msg227390.html Fixes: f214f915 ("tcp: enable MSG_ZEROCOPY") Reported-by:
Marek Majkowski <marek@cloudflare.com> Signed-off-by:
Willem de Bruijn <willemb@google.com> CC: Yuchung Cheng <ycheng@google.com> CC: Neal Cardwell <ncardwell@google.com> CC: Soheil Hassas Yeganeh <soheil@google.com> CC: Alexey Kodanev <alexey.kodanev@oracle.com> Acked-by:
Soheil Hassas Yeganeh <soheil@google.com> Reviewed-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Hangbin Liu authored
[ Upstream commit 80b3671e ] We forgot to update ip6erspan version related info when changing link, which will cause setting new hwid failed. Reported-by:
Jianlin Shi <jishi@redhat.com> Fixes: 94d7d8f2 ("ip6_gre: add erspan v2 support") Signed-off-by:
Hangbin Liu <liuhangbin@gmail.com> Signed-off-by:
-
Andrew Lunn authored
[ Upstream commit e0a7328f ] m88e1318_set_wol() takes the lock as part of phy_select_page(). Don't take the lock again with phy_read(), use the unlocked __phy_read(). Fixes: 424ca4c5 ("net: phy: marvell: fix paged access races") Reported-by:
Åke Rehnman <ake.rehnman@gmail.com> Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Xin Long authored
[ Upstream commit 20704bd1 ] As said in draft-foschiano-erspan-03#section4: Different frame variants known as "ERSPAN Types" can be distinguished based on the GRE "Protocol Type" field value: Type I and II's value is 0x88BE while Type III's is 0x22EB [ETYPES]. So set it properly in erspan_xmit() according to erspan_ver. While at it, also remove the unused parameter 'proto' in erspan_fb_xmit(). Fixes: 94d7d8f2 ("ip6_gre: add erspan v2 support") Reported-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
-
Olivier Matz authored
[ Upstream commit ab5098fa ] In changelink ops, the ip6gre_net pointer is retrieved from dev_net(dev), which is wrong in case of x-netns. Thus, the tunnel is not unlinked from its current list and is relinked into another net namespace. This corrupts the tunnel lists and can later trigger a kernel oops. Fix this by retrieving the netns from device private area. Fixes: c8632fc3 ("net: ip6_gre: Split up ip6gre_changelink()") Cc: Petr Machata <petrm@mellanox.com> Signed-off-by:
Olivier Matz <olivier.matz@6wind.com> Acked-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by:
-
Willem de Bruijn authored
[ Upstream commit 0f149c9f ] Failure __ip_append_data triggers udp_flush_pending_frames, but these tests happen later. The skb must be freed directly. Fixes: bec1f6f6 ("udp: generate gso with UDP_SEGMENT") Reported-by:
-
Ivan Vecera authored
[ Upstream commit 2cddd201 ] Recent changes (especially 05cd271f ("cls_flower: Support multiple masks per priority")) in the fl_flow_mask structure grow it and its current size e.g. on x86_64 with defconfig is 760 bytes and more than 1024 bytes with some debug options enabled. Prior the mentioned commit its size was 176 bytes (using defconfig on x86_64). With regard to this fact it's reasonable to allocate this structure dynamically in fl_change() to reduce its stack size. v2: - use kzalloc() instead of kcalloc() Fixes: 05cd271f ("cls_flower: Support multiple masks per priority") Cc: Jiri Pirko <jiri@resnulli.us> Cc: Paul Blakey <paulb@mellanox.com> Acked-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
Ivan Vecera <ivecera@redhat.com> Signed-off-by:
-
Ido Schimmel authored
When a packet should be trapped to the CPU the device consumes a WQE (work queue element) from an RDQ (receive descriptor queue) and copies the packet to the address specified in the WQE. The device then tries to post a CQE (completion queue element) that contains various metadata (e.g., ingress port) about the packet to a CQ (completion queue). In case the device managed to consume a WQE, but did not manage to post the corresponding CQE, it will get stuck. This unlikely situation can be triggered due to the scheme the driver is currently using to process CQEs. The driver will consume up to 512 CQEs at a time and after processing each corresponding WQE it will ring the RDQ's doorbell, letting the device know that a new WQE was posted for it to consume. Only after processing all the CQEs (up to 512), the driver will ring the CQ's doorbell, letting the device know that new ones can be posted. Fix this by having the driver ring the CQ's doorbell for every processed CQE, but before ringing the RDQ's doorbell. This guarantees that whenever we post a new WQE, there is a corresponding CQE available. Copy the currently processed CQE to prevent the device from overwriting it with a new CQE after ringing the doorbell. Note that the driver still arms the CQ only after processing all the pending CQEs, so that interrupts for this CQ will only be delivered after the driver finished its processing. Before commit 8404f6f2 ("mlxsw: pci: Allow to use CQEs of version 1 and version 2") the issue was virtually impossible to trigger since the number of CQEs was twice the number of WQEs and the number of CQEs processed at a time was equal to the number of available WQEs. Fixes: 8404f6f2 ("mlxsw: pci: Allow to use CQEs of version 1 and version 2") Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Reported-by:
Semion Lisyansky <semionl@mellanox.com> Tested-by:
-
Nir Dotan authored
[ Upstream commit a11dcd64 ] When using a tc flower action of egress mirred redirect, the driver adds an implicit FID setting action. This implicit action sets a dummy FID to the packet and is used as part of a design for trapping unmatched flows in OVS. While this implicit FID setting action is supposed to be a NOP when a redirect action is added, in Spectrum-2 the FID record is consulted as the dummy FID index is an 802.1D FID index and the packet is dropped instead of being redirected. Set the dummy FID index value to be within 802.1Q range. This satisfies both Spectrum-1 which ignores the FID and Spectrum-2 which identifies it as an 802.1Q FID and will then follow the redirect action. Fixes: c3ab4354 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC") Signed-off-by:
Nir Dotan <nird@mellanox.com> Signed-off-by:
-
Ido Schimmel authored
[ Upstream commit f97f4dd8 ] IPv4 routing tables are flushed in two cases: 1. In response to events in the netdev and inetaddr notification chains 2. When a network namespace is being dismantled In both cases only routes associated with a dead nexthop group are flushed. However, a nexthop group will only be marked as dead in case it is populated with actual nexthops using a nexthop device. This is not the case when the route in question is an error route (e.g., 'blackhole', 'unreachable'). Therefore, when a network namespace is being dismantled such routes are not flushed and leaked [1]. To reproduce: # ip netns add blue # ip -n blue route add unreachable 192.0.2.0/24 # ip netns del blue Fix this by not skipping error routes that are not marked with RTNH_F_DEAD when flushing the routing tables. To prevent the flushing of such routes in case #1, add a parameter to fib_table_flush() that indicates if the table is flushed as part of namespace dismantle or not. Note that this problem does not exist in IPv6 since error routes are associated with the loopback device. [1] unreferenced object 0xffff888066650338 (size 56): comm "ip", pid 1206, jiffies 4294786063 (age 26.235s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 b0 1c 62 61 80 88 ff ff ..........ba.... e8 8b a1 64 80 88 ff ff 00 07 00 08 fe 00 00 00 ...d............ backtrace: [<00000000856ed27d>] inet_rtm_newroute+0x129/0x220 [<00000000fcdfc00a>] rtnetlink_rcv_msg+0x397/0xa20 [<00000000cb85801a>] netlink_rcv_skb+0x132/0x380 [<00000000ebc991d2>] netlink_unicast+0x4c0/0x690 [<0000000014f62875>] netlink_sendmsg+0x929/0xe10 [<00000000bac9d967>] sock_sendmsg+0xc8/0x110 [<00000000223e6485>] ___sys_sendmsg+0x77a/0x8f0 [<000000002e94f880>] __sys_sendmsg+0xf7/0x250 [<00000000ccb1fa72>] do_syscall_64+0x14d/0x610 [<00000000ffbe3dae>] entry_SYSCALL_64_after_hwframe+0x49/0xbe [<000000003a8b605b>] 0xffffffffffffffff unreferenced object 0xffff888061621c88 (size 48): comm "ip", pid 1206, jiffies 4294786063 (age 26.235s) hex dump (first 32 bytes): 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk 6b 6b 6b 6b 6b 6b 6b 6b d8 8e 26 5f 80 88 ff ff kkkkkkkk..&_.... backtrace: [<00000000733609e3>] fib_table_insert+0x978/0x1500 [<00000000856ed27d>] inet_rtm_newroute+0x129/0x220 [<00000000fcdfc00a>] rtnetlink_rcv_msg+0x397/0xa20 [<00000000cb85801a>] netlink_rcv_skb+0x132/0x380 [<00000000ebc991d2>] netlink_unicast+0x4c0/0x690 [<0000000014f62875>] netlink_sendmsg+0x929/0xe10 [<00000000bac9d967>] sock_sendmsg+0xc8/0x110 [<00000000223e6485>] ___sys_sendmsg+0x77a/0x8f0 [<000000002e94f880>] __sys_sendmsg+0xf7/0x250 [<00000000ccb1fa72>] do_syscall_64+0x14d/0x610 [<00000000ffbe3dae>] entry_SYSCALL_64_after_hwframe+0x49/0xbe [<000000003a8b605b>] 0xffffffffffffffff Fixes: 8cced9ef ("[NETNS]: Enable routing configuration in non-initial namespace.") Signed-off-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
-
Nir Dotan authored
[ Upstream commit d2f372ba ] Spectrum-2 PHY layer introduces a calibration period which is a part of the Spectrum-2 firmware boot process. Hence increase the SW timeout waiting for the firmware to come out of boot. This does not increase system boot time in cases where the firmware PHY calibration process is done quickly. Fixes: c3ab4354 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC") Signed-off-by:
-
Jason Wang authored
[ Upstream commit cc5e7107 ] Vhost dirty page logging API is designed to sync through GPA. But we try to log GIOVA when device IOTLB is enabled. This is wrong and may lead to missing data after migration. To solve this issue, when logging with device IOTLB enabled, we will: 1) reuse the device IOTLB translation result of GIOVA->HVA mapping to get HVA, for writable descriptor, get HVA through iovec. For used ring update, translate its GIOVA to HVA 2) traverse the GPA->HVA mapping to get the possible GPA and log through GPA. Pay attention this reverse mapping is not guaranteed to be unique, so we should log each possible GPA in this case. This fix the failure of scp to guest during migration. In -next, we will probably support passing GIOVA->GPA instead of GIOVA->HVA. Fixes: 6b1e6cc7 ("vhost: new device IOTLB API") Reported-by:
Jintack Lim <jintack@cs.columbia.edu> Cc: Jintack Lim <jintack@cs.columbia.edu> Signed-off-by:
Jason Wang <jasowang@redhat.com> Acked-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
-
Ross Lagerwall authored
[ Upstream commit 04a4af33 ] For nested and variable attributes, the expected length of an attribute is not known and marked by a negative number. This results in an OOB read when the expected length is later used to check if the attribute is all zeros. Fix this by using the actual length of the attribute rather than the expected length. Signed-off-by:
Ross Lagerwall <ross.lagerwall@citrix.com> Acked-by:
Pravin B Shelar <pshelar@ovn.org> Signed-off-by:
-
Cong Wang authored
[ Upstream commit cd0c4e70 ] Martin reported a set of filters don't work after changing from reclassify to continue. Looking into the code, it looks like skb protocol is not always fetched for each iteration of the filters. But, as demonstrated by Martin, TC actions could modify skb->protocol, for example act_vlan, this means we have to refetch skb protocol in each iteration, rather than using the one we fetch in the beginning of the loop. This bug is _not_ introduced by commit 3b3ae880 ("net: sched: consolidate tc_classify{,_compat}"), technically, if act_vlan is the only action that modifies skb protocol, then it is commit c7e2b968 ("sched: introduce vlan action") which introduced this bug. Reported-by:
Martin Olsson <martin.olsson+netdev@sentorsecurity.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Acked-by:
Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by:
-
Davide Caratti authored
[ Upstream commit 9174c3df ] running the following TDC test cases: 7afc - Replace tunnel_key set action with all parameters 364d - Replace tunnel_key set action with all parameters and cookie it's possible to trigger kmemleak warnings like: unreferenced object 0xffff94797127ab40 (size 192): comm "tc", pid 3248, jiffies 4300565293 (age 1006.862s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 c0 93 f9 8a ff ff ff ff ................ 41 84 ee 89 ff ff ff ff 00 00 00 00 00 00 00 00 A............... backtrace: [<000000001e85b61c>] tunnel_key_init+0x31d/0x820 [act_tunnel_key] [<000000007f3f6ee7>] tcf_action_init_1+0x384/0x4c0 [<00000000e89e3ded>] tcf_action_init+0x12b/0x1a0 [<00000000c1c8c0f8>] tcf_action_add+0x73/0x170 [<0000000095a9fc28>] tc_ctl_action+0x122/0x160 [<000000004bebeac5>] rtnetlink_rcv_msg+0x263/0x2d0 [<000000009fd862dd>] netlink_rcv_skb+0x4a/0x110 [<00000000b55199e7>] netlink_unicast+0x1a0/0x250 [<000000004996cd21>] netlink_sendmsg+0x2c1/0x3c0 [<000000004d6a94b4>] sock_sendmsg+0x36/0x40 [<000000005d9f0208>] ___sys_sendmsg+0x280/0x2f0 [<00000000dec19023>] __sys_sendmsg+0x5e/0xa0 [<000000004b82ac81>] do_syscall_64+0x5b/0x180 [<00000000a0f1209a>] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [<000000002926b2ab>] 0xffffffffffffffff when the tunnel_key action is replaced, the kernel forgets to release the dst metadata: ensure they are released by tunnel_key_init(), the same way it's done in tunnel_key_release(). Fixes: d0f6dd8a ("net/sched: Introduce act_tunnel_key") Signed-off-by:
Davide Caratti <dcaratti@redhat.com> Acked-by:
-
Thomas Petazzoni authored
[ Upstream commit e40e2a2e ] The current code in __mdiobus_register() doesn't properly handle failures returned by the devm_gpiod_get_optional() call: it returns immediately, without unregistering the device that was added by the call to device_register() earlier in the function. This leaves a stale device, which then causes a NULL pointer dereference in the code that handles deferred probing: [ 1.489982] Unable to handle kernel NULL pointer dereference at virtual address 00000074 [ 1.498110] pgd = (ptrval) [ 1.500838] [00000074] *pgd=00000000 [ 1.504432] Internal error: Oops: 17 [#1] SMP ARM [ 1.509133] Modules linked in: [ 1.512192] CPU: 1 PID: 51 Comm: kworker/1:3 Not tainted 4.20.0-00039-g3b73a4cc8b3e-dirty #99 [ 1.520708] Hardware name: Xilinx Zynq Platform [ 1.525261] Workqueue: events deferred_probe_work_func [ 1.530403] PC is at klist_next+0x10/0xfc [ 1.534403] LR is at device_for_each_child+0x40/0x94 [ 1.539361] pc : [<c0683fbc>] lr : [<c0455d90>] psr: 200e0013 [ 1.545628] sp : ceeefe68 ip : 00000001 fp : ffffe000 [ 1.550863] r10: 00000000 r9 : c0c66790 r8 : 00000000 [ 1.556079] r7 : c0457d44 r6 : 00000000 r5 : ceeefe8c r4 : cfa2ec78 [ 1.562604] r3 : 00000064 r2 : c0457d44 r1 : ceeefe8c r0 : 00000064 [ 1.569129] Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none [ 1.576263] Control: 18c5387d Table: 0ed7804a DAC: 00000051 [ 1.582013] Process kworker/1:3 (pid: 51, stack limit = 0x(ptrval)) [ 1.588280] Stack: (0xceeefe68 to 0xceef0000) [ 1.592630] fe60: cfa2ec78 c0c03c08 00000000 c0457d44 00000000 c0c66790 [ 1.600814] fe80: 00000000 c0455d90 ceeefeac 00000064 00000000 0d7a542e cee9d494 cfa2ec78 [ 1.608998] fea0: cfa2ec78 00000000 c0457d44 c0457d7c cee9d494 c0c03c08 00000000 c0455dac [ 1.617182] fec0: cf98ba44 cf926a00 cee9d494 0d7a542e 00000000 cf935a10 cf935a10 cf935a10 [ 1.625366] fee0: c0c4e9b8 c0457d7c c0c4e80c 00000001 cf935a10 c0457df4 cf935a10 c0c4e99c [ 1.633550] ff00: c0c4e99c c045a27c c0c4e9c4 ced63f80 cfde8a80 cfdebc00 00000000 c013893c [ 1.641734] ff20: cfde8a80 cfde8a80 c07bd354 ced63f80 ced63f94 cfde8a80 00000008 c0c02d00 [ 1.649936] ff40: cfde8a98 cfde8a80 ffffe000 c0139a30 ffffe000 c0c6624a c07bd354 00000000 [ 1.658120] ff60: ffffe000 cee9e780 ceebfe00 00000000 ceeee000 ced63f80 c0139788 cf8cdea4 [ 1.666304] ff80: cee9e79c c013e598 00000001 ceebfe00 c013e44c 00000000 00000000 00000000 [ 1.674488] ffa0: 00000000 00000000 00000000 c01010e8 00000000 00000000 00000000 00000000 [ 1.682671] ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 1.690855] ffe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000 [ 1.699058] [<c0683fbc>] (klist_next) from [<c0455d90>] (device_for_each_child+0x40/0x94) [ 1.707241] [<c0455d90>] (device_for_each_child) from [<c0457d7c>] (device_reorder_to_tail+0x38/0x88) [ 1.716476] [<c0457d7c>] (device_reorder_to_tail) from [<c0455dac>] (device_for_each_child+0x5c/0x94) [ 1.725692] [<c0455dac>] (device_for_each_child) from [<c0457d7c>] (device_reorder_to_tail+0x38/0x88) [ 1.734927] [<c0457d7c>] (device_reorder_to_tail) from [<c0457df4>] (device_pm_move_to_tail+0x28/0x40) [ 1.744235] [<c0457df4>] (device_pm_move_to_tail) from [<c045a27c>] (deferred_probe_work_func+0x58/0x8c) [ 1.753746] [<c045a27c>] (deferred_probe_work_func) from [<c013893c>] (process_one_work+0x210/0x4fc) [ 1.762888] [<c013893c>] (process_one_work) from [<c0139a30>] (worker_thread+0x2a8/0x5c0) [ 1.771072] [<c0139a30>] (worker_thread) from [<c013e598>] (kthread+0x14c/0x154) [ 1.778482] [<c013e598>] (kthread) from [<c01010e8>] (ret_from_fork+0x14/0x2c) [ 1.785689] Exception stack(0xceeeffb0 to 0xceeefff8) [ 1.790739] ffa0: 00000000 00000000 00000000 00000000 [ 1.798923] ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 1.807107] ffe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 1.813724] Code: e92d47f0 e1a05000 e8900048 e1a00003 (e5937010) [ 1.819844] ---[ end trace 3c2c0c8b65399ec9 ]--- The actual error that we had from devm_gpiod_get_optional() was -EPROBE_DEFER, due to the GPIO being provided by a driver that is probed later than the Ethernet controller driver. To fix this, we simply add the missing device_del() invocation in the error path. Fixes: 69226896 ("mdio_bus: Issue GPIO RESET to PHYs") Signed-off-by:
Thomas Petazzoni <thomas.petazzoni@bootlin.com> Reviewed-by:
-
Andrew Lunn authored
[ Upstream commit 8cbcdc1a ] The VOD can be out of spec, unless some magic value is poked into an undocumented register in an undocumented page. Fixes: e4cf8a38 ("net: phy: Marvell: Add mv88e6390 internal PHY") Signed-off-by:
-
Ross Lagerwall authored
[ Upstream commit 6c57f045 ] In certain cases, pskb_trim_rcsum() may change skb pointers. Reinitialize header pointers afterwards to avoid potential use-after-frees. Add a note in the documentation of pskb_trim_rcsum(). Found by KASAN. Signed-off-by:
-
Yunjian Wang authored
[ Upstream commit 28c1382f ] The skb header should be set to ethernet header before using is_skb_forwardable. Because the ethernet header length has been considered in is_skb_forwardable(including dev->hard_header_len length). To reproduce the issue: 1, add 2 ports on linux bridge br using following commands: $ brctl addbr br $ brctl addif br eth0 $ brctl addif br eth1 2, the MTU of eth0 and eth1 is 1500 3, send a packet(Data 1480, UDP 8, IP 20, Ethernet 14, VLAN 4) from eth0 to eth1 So the expect result is packet larger than 1500 cannot pass through eth0 and eth1. But currently, the packet passes through success, it means eth1's MTU limit doesn't take effect. Fixes: f6367b46 ("bridge: use is_skb_forwardable in forward path") Cc: bridge@lists.linux-foundation.org Cc: Nkolay Aleksandrov <nikolay@cumulusnetworks.com> Cc: Roopa Prabhu <roopa@cumulusnetworks.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by:
Yunjian Wang <wangyunjian@huawei.com> Signed-off-by:
-
Lendacky, Thomas authored
[ Upstream commit 5ab3121b ] The XGBE hardware has support for performing MDIO operations using an MDIO command request. The driver mistakenly uses the mdio port address as the MDIO command request device address instead of the MDIO command request port address. Additionally, the driver does not properly check for and create a clause 45 MDIO command. Check the supplied MDIO register to determine if the request is a clause 45 operation (MII_ADDR_C45). For a clause 45 operation, extract the device address and register number from the supplied MDIO register and use them to set the MDIO command request device address and register number fields. For a clause 22 operation, the MDIO request device address is set to zero and the MDIO command request register number is set to the supplied MDIO register. In either case, the supplied MDIO port address is used as the MDIO command request port address. Fixes: 732f2ab7 ("amd-xgbe: Add support for MDIO attached PHYs") Signed-off-by:
Tom Lendacky <thomas.lendacky@amd.com> Tested-by:
Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Signed-off-by:
-
- 26 Jan, 2019 3 commits
-
-
Greg Kroah-Hartman authored
-
Corey Minyard authored
commit 913a89f0 upstream. The IPMI driver was recently modified to use SRCU, but it turns out this uses a chunk of percpu memory, even if IPMI is never used. So modify thing to on initialize on the first use. There was already code to sort of handle this for handling init races, so piggy back on top of that, and simplify it in the process. Signed-off-by:
Corey Minyard <cminyard@mvista.com> Reported-by:
Tejun Heo <tj@kernel.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Reviewed-by:
Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: stable@vger.kernel.org # 4.18 Signed-off-by:
-
Corey Minyard authored
commit 7d6380cd upstream. The block number was not being compared right, it was off by one when checking the response. Some statistics wouldn't be incremented properly in some cases. Check to see if that middle-part messages always have 31 bytes of data. Signed-off-by:
-
