- 02 Jun, 2009 1 commit
-
-
Daniel Mack authored
On Thu, May 28, 2009 at 08:42:23PM +0200, Sascha Hauer wrote: > > > Mail-Followup-To: Daniel Mack <daniel@caiaq.de>, > > > linux-arm-kernel@lists.arm.linux.org.uk > > > > ... which causes my mutt to only reply to the list. > > Ah, ok. /me hacking in muttrc... Does it work now? Yep :) > > mxc_register_device(&mxc_uart_device0, &uart_pdata); > > + mxc_register_device(&mxc_uart_device1, &uart_pdata); > > + mxc_register_device(&mxc_uart_device2, &uart_pdata); > > What about the RXD3/TXD3 pins? You're right - I got the IOMUX tables wrong and thought UART0 pins are selected unconditionally. But as it turns out TXD1/RXD1 is for UART0 (mxc_uart_device0), TXD2/RXD2 for UART1 (mxc_uart_device1) etc. Below is a new patch. Thanks, Daniel From e7eb5fa0fed09d667a4b2f168fe466e2cc645abb Mon Sep 17 00:00:00 2001 From: Daniel Mack <daniel@caiaq.de> Date: Wed, 27 May 2009 12:22:51 +0200 Subject: [PATCH] ARM: MX3: add two more UARTs to lilly-1131-db Signed-off-by:
Daniel Mack <daniel@caiaq.de> Signed-off-by:
Sascha Hauer <s.hauer@pengutronix.de>
-
- 28 May, 2009 2 commits
-
-
Valentin Longchamp authored
changes since v1: we now check if the parent configuration bit was changed since reset and change the parent when needed. csi_clk parent was defined with ahb_clk. However, according to the m31 reference manual, it should be serial_pll_clk. Guennadi always used a 20 MHz clock that was by chance changed to a 45 MHz that fits in the mt9t031 spec. Now the clocks are computed and output correctly (measured on oscillo). Signed-off-by:
Valentin Longchamp <valentin.longchamp@epfl.ch> Signed-off-by:
-
Fabio Estevam authored
Add missing mxc_rnga_device entry in devices.h (mxc-master tree). Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
-
- 26 May, 2009 8 commits
-
-
Alberto Panizzo authored
On Mon, 25 May 2009 18:33:28 +0200 Valentin Longchamp <valentin.longchamp@epfl.ch> wrote: > Hello, > > I have updated my mxc git tree and given a compilation spin to your > board support and I have comments. See below. > > > What's the point of declaring this new function, if all it does is > calling the already existing one ? Furthermore, in the current > mxc-master tree, mxc_map_io() does not exist anymore, it should be > mx31_map_io (this breaks compilation for your board). > This patch solve those two issues. Until now i based my patches to vanilla tree. This evening I cloned the mxc-master tree so i could update the armadillo 500 support within recent platform changes. The patch: From e986a8dc262e5292350d95bf65ead75baf3272d7 Mon Sep 17 00:00:00 2001 From: Alberto Panizzo <maramaopercheseimorto@gmail.com> Date: Mon, 25 May 2009 22:24:03 +0200 Subject: [PATCH] Armadillo 500 removing useless function armadillo5x0_map_io and use machine specific io mapping Signed-off-by:
Alberto Panizzo <maramaopercheseimorto@gmail.com> Signed-off-by:
-
Daniel Mack authored
Signed-off-by:
-
Daniel Mack authored
Signed-off-by:
-
Daniel Mack authored
Signed-off-by:
-
Daniel Mack authored
Signed-off-by:
-
Daniel Mack authored
This adds support for the SMSC911x chip found on the lilly-1131 module. Signed-off-by:
-
Daniel Mack authored
Support code for lilly-1131 is implemented in a module/baseboard fashion. All code specific to peripherals found on the development board will go to this file. Signed-off-by:
-
Daniel Mack authored
This patch adds basic support for INCO startec's LILLY-1131 iMX31 based modules. The module needs a baseboard support to work which will be added in the next patch. Signed-off-by:
-
- 20 May, 2009 1 commit
-
-
Eric Lammerts authored
Signed-off-by:
Eric Lammerts <eric@lammerts.org> Signed-off-by:
-
- 19 May, 2009 2 commits
-
-
Magnus Lilja authored
Signed-off-by:
Magnus Lilja <lilja.magnus@gmail.com> Signed-off-by:
-
Alberto Panizzo authored
Signed-off-by:
-
- 18 May, 2009 1 commit
-
-
Magnus Lilja authored
The i.MX31 PDK consists of several boards, one of them is a debug board containing a CPLD which controls some debug leds, switch buttons, an interrupt chip and an Ethernet controller. This patch adds support for detecting if the PDK board is present (during boot) and adds the interrupt chip to the kernel. Signed-off-by:
-
- 17 May, 2009 1 commit
-
-
Sascha Hauer authored
Without this patch we end up with a log message like "mx3_sdc_fb mx3_sdc_fb: mx3fb: fb registered". That's two fb too much for my taste. Signed-off-by:
-
- 16 May, 2009 3 commits
-
-
Magnus Lilja authored
Restructure UART pin setup in preparation for adding other pins in later patches. Signed-off-by:
-
Alberto Panizzo authored
From ff1fd9d7015d9b9ad3e0df2016d0415e2719747c Mon Sep 17 00:00:00 2001 From: Alberto Panizzo <maramaopercheseimorto@gmail.com> Date: Fri, 15 May 2009 17:21:21 +0200 Subject: [PATCH] Make sure ipg_per_clk is generated by ipg_clk and not usb_pll Signed-off-by:
-
Magnus Lilja authored
Signed-off-by:
-
- 13 May, 2009 1 commit
-
-
Guennadi Liakhovetski authored
mx3fb.c calls disable_irq() from a DMA callback, i.e., in an IRQ-handler context, which has always been unsafe, and became deadly after the merge of threaded interrupt handler support. Use disable_irq_nosync() instead. Signed-off-by:
Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
- 07 May, 2009 20 commits
-
-
Valentin Longchamp authored
Signed-off-by:
-
Valentin Longchamp authored
This adds the camera device based on Guennadi's soc_camera architecture for the mx31. The proposed init by Guennadi was removed and must be implemented in the board init file as it contains a lot of board specific info (memory size, clock speed). Signed-off-by:
-
Valentin Longchamp authored
This is used on all board of our system, so again this is done in the mx31moboard.c file. changes since v2: call to gpio_request added in platform code, and moved device initialization in baseboard files. changes since v1: pins are claimed in another patch Signed-off-by:
-
Sascha Hauer authored
In order to use the gpiolib, we now have to call gpio_request in the plaform code since it is not done in iomux code anymore. Signed-off-by: -
Valentin Longchamp authored
Since iomux code is not directly related to gpio on mx31, the calls to gpio_request are removed from iomux.c file. These calls have to be done in platform initialization files. The name of the singe pin call for iomux is also changed to mxc_iomux_alloc_pin. Signed-off-by:
-
Sascha Hauer authored
Signed-off-by: -
Sascha Hauer authored
Signed-off-by: -
Sascha Hauer authored
Signed-off-by: -
Sascha Hauer authored
Signed-off-by: -
Sascha Hauer authored
Signed-off-by: -
Sascha Hauer authored
header is part of the kernel now. Signed-off-by: -
Guennadi Liakhovetski authored
Add OTG device definition and resources to i.MX31 and a pure USB device mode support to the pcm037 board. Signed-off-by:
Guennadi Liakhovetski <lg@denx.de> Signed-off-by:
-
Sascha Hauer authored
Signed-off-by: -
Sascha Hauer authored
Also, remove usage of set_irq_type after request_irq. Signed-off-by: -
Vladimir Barinov authored
Add SDHC support for MX27ADS board Signed-off-by:
Vladimir Barinov <vbarinov@embeddedalley.com> Signed-off-by:
-
Vladimir Barinov authored
Add 1-wire support for MX27ADS board Signed-off-by:
-
Vladimir Barinov authored
Add Sharp-QVGA panel support for MX27ADS board Signed-off-by:
-
Vladimir Barinov authored
Add I2C support for MX27ADS board Signed-off-by:
-
Vladimir Barinov authored
Add NAND support for MX27ADS board Signed-off-by:
-
Vladimir Barinov authored
Setup all pins at once in one table Signed-off-by:
-
