The regulator core supports this to allow the configuration to be inspected
at runtime even if no software mangement is enabled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>

There's some other allocations but they're not so trivial as they use
kmemdup() and kstrdup().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Convert mc13892_sw_regulator_ops and mc13xxx_regulator_ops to set_voltage_sel.
mc13xxx_get_best_voltage_index function is not used now, remove it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Adding flag on fixed regulator board configuration structure
to specify whether gpio is open drain type or not.
Passing this information to gpio library when requesting
gpio so that gpio driver can set the pin state accordingly,
for open drain type:
- Pin can be set HIGH as setting as input, PULL UP on
  pin make this as HIGH.
- Pin can be set LOW as setting it as output and drive to LOW.

The non-open drain pin can be  set HIGH/LOW by setting it to
output and driving it to HIGH/LOW.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

According to the datasheet[1], tps62360 is register compatible with tps62362.
tps62361B is register compatible with tps62363.
Thus this patch adds support for tps62362 and tps62363.

[1] http://www.ti.com/litv/pdf/slvsau9bSigned-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The n_voltages are the same for all regulators: (max - min / step) + 1 == 64.
The vol_shift is always 0, and the vol_nbits is always the same as n_voltages
setting. Thus we can remove vol_shitf and vol_nbits fields from struct
max8925_regulator_info.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Current code implements max8925_list_voltage but does not set the list_voltage
callback function in max8925_regulator_[ldo|sdv]_ops. Fix it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Tested-by: Jett Zhou <jtzhou@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Tested-by: Jett Zhou <jtzhou@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Then we can remove the vol_nbits field from struct pm8607_regulator_info.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Tested-by: Jett Zhou <jtzhou@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Current code implements pm8607_list_voltage but does not set the list_voltage
callback function in pm8607_regulator_ops. Fix it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Tested-by: Jett Zhou <jtzhou@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Integer division may truncate the result.
Current code shows changing current is 0mA when selector is 1 ... 8.

For example:
selector = 1
ad5398_calc_current returns 117, debug message shows 117/1000 = 0mA
selector = 2
ad5398_calc_current returns 234, debug message shows 234/1000 = 0mA
selector = 3
ad5398_calc_current returns 351, debug message shows 351/1000 = 0mA
............
selector = 8
ad5398_calc_current returns 937, debug message shows 937/1000 = 0mA

Show the changing current in uA makes it easier for debugging.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The client field of struct tps_pmic is not used after converting to regmap API.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The client field of struct tps62360_chip is not used after converting to regmap.
The name field of struct tps62360_chip is not used in this driver.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

In current implementation, da9052_ldo_ops and da9052_ldo5_6_ops are very
similar, only the set_voltage is slightly different.
da9052_buckperi_ops and da9052_dcdc_ops are also similar.

This patch adds da9052_regulator_set_voltage for the set_voltage callback
used by all LDOs and DCDCs. Rework da9052_get_regulator_voltage_sel and
da9052_set_dcdc_voltage to make it possible to be shared by all DCDCs.
Rework da9052_list_voltage to make it to be shared by all DCDCs and LDOs.

Then we can remove da9052_ldo5_6_ops and da9052_buckperi_ops.
We can also remove DA9052_LDO5_6 and DA9052_BUCKPERI macros which is not used
now.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The regulator name for LDOs are LDO4 ... LDO13 in current implementation.
The correct regulator name for LDOs should be LDO1 ... LDO10.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This patch also changes the define for TPS65023_LDO_CTRL_LDOx_MASK,
because regmap_update_bits actually does:
        (orig & ~mask) | (val & mask)
This change makes the code consists for all regmap_update_bits calls.

Also removes some uninformative comments.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

MAX8997_VOLTAGE_REGULATOR macro has _name and _ops parameters so we can use it
for all regulators with REGULATOR_VOLTAGE type.
The MAX8997_VOLTAGE_REGULATOR now replaces regulator_desc_ldo and
regulator_desc_buck macros.

MAX8997_CURRENT_REGULATOR is for CHARGER and CHARGER_TOPOFF.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Check max8997->buck[1|2|5]_gpiodvs status in max8997_get_voltage_register
and return correct register accordingly.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Both _en_bit and _ops parameters for all DCDCs and FETs are the same, so we
can hardcode it in tps65090_REG macro.

_en_reg can be calculated by _id + 12, so we can also remove it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

regulator_register never returns NULL.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Now all the callback implementation are the same for both ldo and dvm
regulator_ops, merge them to tps6586x_regulator_ops.

Also rename tps6586x_ldo_list_voltage to tps6586x_list_voltage.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Convert both tps6586x_[ldo|dvm]_set_voltage to one set_voltage_sel callback.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This also fixes a bug, LDO0 has minimal voltage 1.2V rather than 1.25V.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

After converting to set_voltage_sel, we can remove the workaroud of getting
the best match voltage for V1. The core will iterate through the whole voltage
table and find the best match for us.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-By: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-By: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Add TPS65090 regulator driver

TPS65090 PMIC from TI consists of 3 step down converters,
2 always on LDOs and 7 current limited load switches. The
output voltages are ON/OFF controllable and are meant to
supply power to the components on target board.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Do not assume the gpio regulator states map is sorted in any order.
This patch ensures we always set the smallest voltage/current that falls within
the specified range.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Rather than replicating the core support for always on regulators use
a different set of ops with none of the enable related operations provided
when we don't have any ops. This ensures that we automatically pick up
any enhanced support for such regulators that the core has such as the
warnings about regulation constraints that can't be used.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Now tps65912_get_voltage_dcdc and tps65912_get_voltage_ldo has exactly the same
implementation. We can merge them to tps65912_get_voltage function.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>