We are spending between 40 and 160 cycles with a mean of 65 cycles in
the DTLB handling routine (measured with mftbl) so make it more
simple althought it adds one instruction.
With this modification, we get three registers available at all time,
which will help with following patch.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>

add the missing RAID Engine device node for p5040.
otherwise, the device can not be detected.
Signed-off-by: Xuelin Shi <xuelin.shi@nxp.com>
Signed-off-by: Scott Wood <oss@buserror.net>

csum_partial is often called for small fixed length packets
for which it is suboptimal to use the generic csum_partial()
function.

For instance, in my configuration, I got:
* One place calling it with constant len 4
* Seven places calling it with constant len 8
* Three places calling it with constant len 14
* One place calling it with constant len 20
* One place calling it with constant len 24
* One place calling it with constant len 32

This patch renames csum_partial() to __csum_partial() and
implements csum_partial() as a wrapper inline function which
* uses csum_add() for small 16bits multiple constant length
* uses ip_fast_csum() for other 32bits multiple constant
* uses __csum_partial() in all other cases
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>

Modify platform driver suspend/resume to syscore
suspend/resume. This is because p1022ds needs to use
localbus when entering the PCIE resume.
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
[scottwood: dropped makefile churn]
Signed-off-by: Scott Wood <oss@buserror.net>

When CONFIG_DEBUG_PAGEALLOC is activated, the initial TLB mapping gets
flushed to track accesses to wrong areas. Therefore, kernel addresses
will also generate ITLB misses.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>

The MPC885 reference manual says that SDCR shall have value 0x40, but
most exemples set SDCR to 0x1
With 0x1 in SDCR, we observe TX underruns on SCC when using it in
QMC mode.
According the NXP technical support, this is a copy/paste error from
MPC860 reference manual, 0x40 being the only value supported
by the MPC885 HW.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>

This patch disables deprecated IDE subsystem in mpc8610_hpcd_defconfig
(no IDE host drivers are selected in this config so there is no valid
reason to enable IDE subsystem itself).
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Scott Wood <oss@buserror.net>

This patch disables deprecated IDE subsystem in stx_gp3_defconfig
(no IDE host drivers are selected in this config so there is no valid
reason to enable IDE subsystem itself).

Cc: Scott Wood <oss@buserror.net>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Scott Wood <oss@buserror.net>

This patch disables deprecated IDE subsystem in ksi8560_defconfig
(no IDE host drivers are selected in this config so there is no valid
reason to enable IDE subsystem itself).

Cc: Scott Wood <oss@buserror.net>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Scott Wood <oss@buserror.net>

This patch disables deprecated IDE subsystem in mpc834x_itx_defconfig
(no IDE host drivers are selected in this config so there is no valid
reason to enable IDE subsystem itself).

Cc: Scott Wood <oss@buserror.net>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Scott Wood <oss@buserror.net>

cpm_muram_alloc_common is called twice and both the times
spin_lock_irqsave is held.
Using GFP_KERNEL can sleep in spin_lock_irqsave context and cause
deadlock
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: Scott Wood <oss@buserror.net>

as cpm_muram_alloc_common is used only in this file,
making it static
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: Scott Wood <oss@buserror.net>

127 is the theoretical up boundary of QEIC number,
in fact there only be 44 qe_ic_info now.
add check to overflow for qe_ic_info
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Scott Wood <oss@buserror.net>

The FMan contains internal PHY devices used for SGMII connections
to external PHYs. When these PHYs are in use a reference is needed
for both the external PHY and the internal one. For the external
PHY phy-handle provides the reference. For the internal PHY a new
handle is required.
In dTSEC, the internal PHY is a TBI (Ten Bit Interface) PHY,
the handle used will be tbi-handle.
In mEMAC, the internal PHY is a PCS (Physical Coding Sublayer) PHY,
the handle used will be pcsphy-handle.
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Signed-off-by: Scott Wood <oss@buserror.net>

Support Freescale E6500 core-based platforms, like t4240.
Support disabling/enabling individual CPU thread dynamically.
Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>

Freescale E500MC and E5500 core-based platforms, like P4080, T1040,
support disabling/enabling CPU dynamically.
This patch adds this feature on those platforms.
Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@feescale.com>
[scottwood: removed unused pr_fmt]
Signed-off-by: Scott Wood <oss@buserror.net>

Freescale CoreNet-based and Non-CoreNet-based platforms require
different PM operations. This patch extracted existing PM operations
on Non-CoreNet-based platforms to a new file which can accommodate
both platforms. In this way, PM operation codes are clearer structurally.
Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@feescale.com>
Signed-off-by: Scott Wood <oss@buserror.net>

There is a RCPM (Run Control/Power Management) in Freescale QorIQ
series processors. The device performs tasks associated with device
run control and power management.

The driver implements some features: mask/unmask irq, enter/exit low
power states, freeze time base, etc.
Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
[scottwood: remove __KERNEL__ ifdef]
Signed-off-by: Scott Wood <oss@buserror.net>

Various e500 core have different cache architecture, so they
need different cache flush operations. Therefore, add a callback
function cpu_flush_caches to the struct cpu_spec. The cache flush
operation for the specific kind of e500 is selected at init time.
The callback function will flush all caches inside the current cpu.
Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@feescale.com>
Signed-off-by: Scott Wood <oss@buserror.net>

On e6500, in the case of cpu hotplug, either thread in one core
may be the first thread initilzing the TLB1. The subsequent threads
must not setup it again.

The code is derived from the comment of Scott Wood.
Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>
Signed-off-by: Scott Wood <oss@buserror.net>

RCPM is the Run Control and Power Management module performs all
device-level tasks associated with device run control and power
management.

Add this for freescale powerpc platform and layerscape platform.
Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
[scottwood: s/pointer/phandle and "disabled" status from example]
Signed-off-by: Scott Wood <oss@buserror.net>

Simplify csum_add(a, b) in case a or b is constant 0
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>

On the 8xx, load latency is 2 cycles and taking branches also takes
2 cycles. So let's unroll the loop.

This patch improves csum_partial() speed by around 10% on both:
* 8xx (single issue processor with parallel execution)
* 83xx (superscalar 6xx processor with dual instruction fetch
and parallel execution)
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>

r5 does contain the value to be updated, so lets use r5 all way long
for that. It makes the code more readable.

To avoid confusion, it is better to use adde instead of addc

The first addition is useless. Its only purpose is to clear carry.
As r4 is a signed int that is always positive, this can be done by
using srawi instead of srwi

Let's also remove the comment about bdnz having no overhead as it
is not correct on all powerpc, at least on MPC8xx

In the last part, in our situation, the remaining quantity of bytes
to be proceeded is between 0 and 3. Therefore, we can base that part
on the value of bit 31 and bit 30 of r4 instead of anding r4 with 3
then proceding on comparisons and substractions.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>

csum_partial_copy_generic() does the same as copy_tofrom_user and also
calculates the checksum during the copy. Unlike copy_tofrom_user(),
the existing version of csum_partial_copy_generic() doesn't take
benefit of the cache.

This patch is a rewrite of csum_partial_copy_generic() based on
copy_tofrom_user().
The previous version of csum_partial_copy_generic() was handling
errors. Now we have the checksum wrapper functions to handle the error
case like in powerpc64 so we can make the error case simple:
just return -EFAULT.
copy_tofrom_user() only has r12 available => we use it for the
checksum r7 and r8 which contains pointers to error feedback are used,
so we stack them.

On a TCP benchmark using socklib on the loopback interface on which
checksum offload and scatter/gather have been deactivated, we get
about 20% performance increase.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>

In several architectures, ip_fast_csum() is inlined
There are functions like ip_send_check() which do nothing
much more than calling ip_fast_csum().
Inlining ip_fast_csum() allows the compiler to optimise better
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[scottwood: whitespace and cast fixes]
Signed-off-by: Scott Wood <oss@buserror.net>

The powerpc64 checksum wrapper functions adds csum_and_copy_to_user()
which otherwise is implemented in include/net/checksum.h by using
csum_partial() then copy_to_user()

Those two wrapper fonctions are also applicable to powerpc32 as it is
based on the use of csum_partial_copy_generic() which also
exists on powerpc32

This patch renames arch/powerpc/lib/checksum_wrappers_64.c to
arch/powerpc/lib/checksum_wrappers.c and
makes it non-conditional to CONFIG_WORD_SIZE
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>

addc uses carry so xer is clobbered in csum_add()
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>

csum_tcpudp_magic is now an inline function, so there is
nothing to export
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>

No code changes.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

No code changes.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

We don't need to update linux page table entry with _PAGE_HASHPTE early
in hash pte fault. A parallel pte update will loop via _PAGE_BUSY
and look at _PAGE_HASHPTE for a required hpte flush only if
_PAGE_BUSY is cleared. That ensures a pte update will wait for a
parallel hpte insert to finish before looking at _PAGE_HASHPTE bit.

To avoid further confusion drop setting _PAGE_HASHPTE in cmpxchg in __hash_page_4K.

commit 41743a4e ("powerpc: Free a PTE bit on ppc64 with 64K pages")
did similar change for 64K config
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

We are updating pte in those functions.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

With next generation power processor, we are having a new mmu model
[1] that require us to maintain a different linux page table format.

Inorder to support both current and future ppc64 systems with a single
kernel we need to make sure kernel can select between different page
table format at runtime. With the new MMU (radix MMU) added, we will
have two different pmd hugepage size 16MB for hash model and 2MB for
Radix model. Hence make HPAGE_PMD related values as a variable.

Actual conversion of HPAGE_PMD to a variable for ppc64 happens in a
followup patch.

[1] http://ibm.biz/power-isa3 (Needs registration).
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This is needed so that we can support both hash and radix page table
using single kernel. Radix kernel uses a 4 level table.

We now use physical address in upper page table tree levels. Even though
they are aligned to their size, for the masked bits we use the
bit positions as per PowerISA 3.0.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

We remove real_pte_t out of STRICT_MM_TYPESCHECK.
Reviewed-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

We move the page table accessors into a separate header. We will
later add a big endian variant of the table which is needed for radix.
No functionality change only code movement.
Reviewed-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This patch adds the ability to be able to save the VSX registers to the
thread struct without giving up (disabling the facility) next time the
process returns to userspace.

This patch builds on a previous optimisation for the FPU and VEC registers
in the thread copy path to avoid a possibly pointless reload of VSX state.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This patch adds the ability to be able to save the VEC registers to the
thread struct without giving up (disabling the facility) next time the
process returns to userspace.

This patch builds on a previous optimisation for the FPU registers in the
thread copy path to avoid a possibly pointless reload of VEC state.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This patch adds the ability to be able to save the FPU registers to the
thread struct without giving up (disabling the facility) next time the
process returns to userspace.

This patch optimises the thread copy path (as a result of a fork() or
clone()) so that the parent thread can return to userspace with hot
registers avoiding a possibly pointless reload of FPU register state.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>