When raid1/raid10 array fails to write to one of the drives, the request
is added to bio_end_io_list and finished by personality thread. The
thread doesn't handle it as long as MD_CHANGE_PENDING flag is set. In
case of external metadata this flag is cleared, however the thread is
not woken up. It causes request to be blocked for few seconds (until
another action on the array wakes up the thread) or to get stuck
indefinitely.

Wake up personality thread once MD_CHANGE_PENDING has been cleared.
Moving 'restart_array' call after the flag is cleared it not a solution
because in read-write mode the call doesn't wake up the thread.
Signed-off-by: Tomasz Majchrzak <tomasz.majchrzak@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>

If external metadata handler supports bad blocks and unacknowledged bad
blocks are present, don't report disk via sysfs as faulty. Such
situation can be still handled so disk just has to be blocked for a
moment. It makes it consistent with kernel state as corresponding rdev
flag is also not set.

When the disk in being unblocked there are few cases:
1. Disk has been in blocked and faulty state, it is being unblocked but
it still remains in faulty state. Metadata handler will remove it from
array in the next call.
2. There is no bad block support in external metadata handler and bad
blocks are present - put the disk in blocked and faulty state (see
case 1).
3. There is bad block support in external metadata handler and all bad
blocks are acknowledged - clear all flags, continue.
4. There is bad block support in external metadata handler but there are
still unacknowledged bad blocks - clear all flags, continue. It is fine
to clear Blocked flag because it was probably not set anyway (if it was
it is case 1). BlockedBadBlocks flag can also be cleared because the
request waiting for it will set it again when it finds out that some bad
block is still not acknowledged. Recovery is not necessary but there are
no problems if the flag is set. Sysfs rdev state is still reported as
blocked (due to unacknowledged bad blocks) so metadata handler will
process remaining bad blocks and unblock disk again.
Signed-off-by: Tomasz Majchrzak <tomasz.majchrzak@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>

Add new rdev flag which external metadata handler can use to switch
on/off bad block support. If new bad block is encountered, notify it via
rdev 'unacknowledged_bad_blocks' sysfs file. If bad block has been
cleared, notify update to rdev 'bad_blocks' sysfs file.

When bad blocks support is being removed, just clear rdev flag. It is
not necessary to reset badblocks->shift field. If there are bad blocks
cleared or added at the same time, it is ok for those changes to be
applied to the structure. The array is in blocked state and the drive
which cannot handle bad blocks any more will be removed from the array
before it is unlocked.

Simplify state_show function by adding a separator at the end of each
string and overwrite last separator with new line.
Signed-off-by: Tomasz Majchrzak <tomasz.majchrzak@intel.com>
Reviewed-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>

Implement the AVX2 optimization of RAID6 xor_syndrome functions which is
simply based on sse2.c written by hpa.

Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Yuanhan Liu <yuanhan.liu@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Gayatri Kammela <gayatri.kammela@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>

Pull arm64 fix from Will Deacon:
 "It's been pretty quiet on the fixes side of things for us, but Artem
  reported a build failure introduced during the merge window that
  appears with older GCCs that do not support asm goto. The fix is
  bigger than I'd like, but it's a mechnical move of some constants to
  break an include dependency between atomic.h and jump_label.h when
  !HAVE_JUMP_LABEL.

  Summary:

   - Fix build failure on compilers without asm goto"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: Fix circular include of asm/lse.h through linux/jump_label.h

Merge tag 'openrisc-for-linus-v4.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull openrisc fix from Guenter Roeck:
 "Fix openrisc crash caused by ro_init changes"

* tag 'openrisc-for-linus-v4.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  openrisc: Define __ro_after_init to avoid crash

Merge tag 'hwmon-for-linus-v4.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fix from Guenter Roeck:
 "Fix resource leak on devm_kcalloc failure"

* tag 'hwmon-for-linus-v4.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (core) fix resource leak on devm_kcalloc failure

Pull HID fixes from Jiri Kosina:

 - modprobe-after-rmmod load failure bugfix for intel-ish, from Even Xu

 - IRQ probing bugfix for intel-ish, from Srinivas Pandruvada

 - attribute parsing fix in hid-sensor, from Ooi, Joyce

 - other small misc fixes / quirky device additions

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: sensor: fix attributes in HID sensor interface
  HID: intel-ish-hid: request_irq failure
  HID: intel-ish-hid: Fix driver reinit failure
  HID: intel-ish-hid: Move DMA disable code to new function
  HID: intel-ish-hid: consolidate ish wake up operation
  HID: usbhid: add ATEN CS962 to list of quirky devices
  HID: intel-ish-hid: Fix !CONFIG_PM build warning
  HID: sensor-hub: Fix packing of result buffer for feature report

openrisc qemu tests fail with the following crash.

Unable to handle kernel access at virtual address 0xc0300c34

Oops#: 0001
CPU #: 0
   PC: c016c710    SR: 0000ae67    SP: c1017e04
   GPR00: 00000000 GPR01: c1017e04 GPR02: c0300c34 GPR03: c0300c34
   GPR04: 00000000 GPR05: c0300cb0 GPR06: c0300c34 GPR07: 000000ff
   GPR08: c107f074 GPR09: c0199ef4 GPR10: c1016000 GPR11: 00000000
   GPR12: 00000000 GPR13: c107f044 GPR14: c0473774 GPR15: 07ce0000
   GPR16: 00000000 GPR17: c107ed8a GPR18: 00009600 GPR19: c107f044
   GPR20: c107ee74 GPR21: 00000003 GPR22: c0473770 GPR23: 00000033
   GPR24: 000000bf GPR25: 00000019 GPR26: c046400c GPR27: 00000001
   GPR28: c0464028 GPR29: c1018000 GPR30: 00000006 GPR31: ccf37483
     RES: 00000000 oGPR11: ffffffff
     Process swapper (pid: 1, stackpage=c1001960)

     Stack: Stack dump [0xc1017cf8]:
     sp + 00: 0xc1017e04
     sp + 04: 0xc0300c34
     sp + 08: 0xc0300c34
     sp + 12: 0x00000000
...

Bisect points to commit d2ec3f77 ("pty: make ptmx file ops read-only
after init"). Fix by defining __ro_after_init for the openrisc
architecture, similar to parisc.

Fixes: d2ec3f77 ("pty: make ptmx file ops read-only after init")
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Stafford Horne <shorne@gmail.com>

Pull i2c fix from Wolfram Sang:
 "A bugfix for the I2C core fixing a (rare) race condition"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: core: fix NULL pointer dereference under race condition

Commit efd9e03f ("arm64: Use static keys for CPU features")
introduced support for static keys in asm/cpufeature.h, including
linux/jump_label.h. When CC_HAVE_ASM_GOTO is not defined, this causes a
circular dependency via linux/atomic.h, asm/lse.h and asm/cpufeature.h.

This patch moves the capability macros out out of asm/cpufeature.h into
a separate asm/cpucaps.h and modifies some of the #includes accordingly.

Fixes: efd9e03f ("arm64: Use static keys for CPU features")
Reported-by: Artem Savkov <asavkov@redhat.com>
Tested-by: Artem Savkov <asavkov@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

Merge branches 'sched-urgent-for-linus' and 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull stack vmap fixups from Thomas Gleixner:
 "Two small patches related to sched_show_task():

   - make sure to hold a reference on the task stack while accessing it

   - remove the thread_saved_pc printout

  .. and add a sanity check into release_task_stack() to catch problems
  with task stack references"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/core: Remove pointless printout in sched_show_task()
  sched/core: Fix oops in sched_show_task()

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  fork: Add task stack refcounting sanity check and prevent premature task stack freeing

Pull MD fixes from Shaohua Li:
 "There are several bug fixes queued:

   - fix raid5-cache recovery bugs

   - fix discard IO error handling for raid1/10

   - fix array sync writes bogus position to superblock

   - fix IO error handling for raid array with external metadata"

* tag 'md/4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
  md: be careful not lot leak internal curr_resync value into metadata. -- (all)
  raid1: handle read error also in readonly mode
  raid5-cache: correct condition for empty metadata write
  md: report 'write_pending' state when array in sync
  md/raid5: write an empty meta-block when creating log super-block
  md/raid5: initialize next_checkpoint field before use
  RAID10: ignore discard error
  RAID1: ignore discard error

Pull SCSI fixes from James Bottomley:
 "Two more important data integrity fixes related to RAID device drivers
  which wrongly throw away the SYNCHRONIZE CACHE command in the non-RAID
  path and a memory leak in the scsi_debug driver"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: arcmsr: Send SYNCHRONIZE_CACHE command to firmware
  scsi: scsi_debug: Fix memory leak if LBP enabled and module is unloaded
  scsi: megaraid_sas: Fix data integrity failure for JBOD (passthrough) devices

Pull input subsystem updates from Dmitry Torokhov.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: psmouse - cleanup Focaltech code
  Input: i8042 - add XMG C504 to keyboard reset table

Pull FireWire (IEEE 1394) fixes from Stefan Richter:

 - add missing input validation to the firewire-net driver. Invalid
   IP-over-1394 encapsulation headers could trigger buffer overflows
   (CVE 2016-8633).

 - IP-over-1394 link fragmentation headers were read and written
   incorrectly, breaking fragmented RX/TX with other OS's stacks.

* tag 'firewire-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
  firewire: net: fix fragmented datagram_size off-by-one
  firewire: net: guard against rx buffer overflows

Pull media fixes from Mauro Carvalho Chehab:
 "A series of fixup patches meant to fix the usage of DMA on stack, plus
  one warning fixup"

* tag 'media/v4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (32 commits)
  [media] radio-bcm2048: don't ignore errors
  [media] pctv452e: fix semicolon.cocci warnings
  [media] flexcop-usb: don't use stack for DMA
  [media] stk-webcam: don't use stack for DMA
  [media] s2255drv: don't use stack for DMA
  [media] cpia2_usb: don't use stack for DMA
  [media] digitv: handle error code on RC query
  [media] dw2102: return error if su3000_power_ctrl() fails
  [media] nova-t-usb2: handle error code on RC query
  [media] technisat-usb2: use DMA buffers for I2C transfers
  [media] pctv452e: don't call BUG_ON() on non-fatal error
  [media] pctv452e: don't do DMA on stack
  [media] nova-t-usb2: don't do DMA on stack
  [media] gp8psk: don't go past the buffer size
  [media] gp8psk: don't do DMA on stack
  [media] dtv5100: don't do DMA on stack
  [media] dtt200u: handle USB control message errors
  [media] dtt200u: don't do DMA on stack
  [media] dtt200u-fe: handle errors on USB control messages
  [media] dtt200u-fe: don't do DMA on stack
  ...

Pull PCI fixes from Bjorn Helgaas:

 - fix for a Qualcomm driver issue that causes a use-before-set crash

 - fix for DesignWare iATU unroll support that causes external aborts
   when enabling the host bridge

* tag 'pci-v4.9-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: designware: Check for iATU unroll support after initializing host
  PCI: qcom: Fix pp->dev usage before assignment

Pull MTD fixes from Brian Norris:

 - MAINTAINERS updates to reflect some new maintainers/submaintainers.

   We have some great volunteers who've been developing and reviewing
   already. We're going to try a group maintainership model, so
   eventually you'll probably see pull requests from people besides me.

 - NAND fixes from Boris:
    "Three simple fixes:

      - fix a non-critical bug in the gpmi driver
      - fix a bug in the 'automatic NAND timings selection' feature
        introduced in 4.9-rc1
      - fix a false positive uninitialized-var warning"

* tag 'for-linus-20161104' of git://git.infradead.org/linux-mtd:
  mtd: mtk: avoid warning in mtk_ecc_encode
  mtd: nand: Fix data interface configuration logic
  mtd: nand: gpmi: disable the clocks on errors
  MAINTAINERS: add more people to the MTD maintainer team
  MAINTAINERS: add a maintainer for the SPI NOR subsystem

Pull MMC fixes from Ulf Hansson:
 "MMC host:

   - sdhci-msm: Fix error path in probe
   - dw_mmc-pltfm: Avoid NULL pointer dereference"

* tag 'mmc-v4.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: sdhci-msm: Fix error return code in sdhci_msm_probe()
  mmc: dw_mmc-pltfm: fix the potential NULL pointer dereference

Pull GPIO fixes from Linus Walleij:
 "Some GPIO fixes for the v4.9 series:

   - Fix a nasty file descriptor leak when getting line handles.

   - A fix for a cleanup that seemed innocent but created a problem for
     drivers instantiating several gpiochips for one single OF node.

   - Fix a unpredictable problem using irq_domain_simple() in the mvebu
     driver by converting it to a lineas irqdomain"

* tag 'gpio-v4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio/mvebu: Use irq_domain_add_linear
  gpio: of: fix GPIO drivers with multiple gpio_chip for a single node
  gpio: GPIO_GET_LINE{HANDLE,EVENT}_IOCTL: Fix file descriptor leak

User is unable to access to input-X-yyy and feature-X-yyy where
X is a hex value and more than 9 (e.g. input-a-yyy, feature-b-yyy) in HID
sensor custom sysfs interface.
This is because when creating the attribute, the attribute index is
written to using %x (hex). However, when reading and writing values into
the attribute, the attribute index is scanned using %d (decimal). Hence,
user is unable to access to attributes with index in hex values
(e.g. 'a', 'b', 'c') but able to access to attributes with index in
decimal values (e.g. 1, 2, 3,..).
This fix will change input-%d-%x-%s and feature-%d-%x-%s to input-%x-%x-%s
and feature-%x-%x-%s in show_values() and store_values() accordingly.
Signed-off-by: Ooi, Joyce <joyce.ooi@intel.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

On some platforms ISH interrupt is shared, which causes request_irq to
fail. This requires IRQF_SHARED irq flag.

But IRQF_NO_SUSPEND and IRQF_SHARED should not be used together, so
removed IRQF_NO_SUSPEND flag. Anyway this driver doesn't require
IRQF_NO_SUSPEND, as this interrupt is not required during "noirq" phases
of suspending and resuming devices as well as during the time when
nonboot CPUs are taken offline and brought back online.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

When built as a module, modprobe followed by rmmod can fail because
DMA was still active. So to fix this, DMA needs to be disabled during
module exit.

This change disables DMA during modules exit and change the ISH PCI
device status to D3.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Add a new function ish_disable_dma() and move DMA disable operations
here, so that this functionality can be reused.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Same operations are done in ish_hw_start() and _ish_hw_reset() to
wakeup ISH device. Consolidate them by introducing a new function
ish_wakeup() and move the code there.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Pull nfsd bugfixes from Bruce Fields:
 "Fixes for some recent regressions including fallout from the vmalloc'd
  stack change (after which we can no longer encrypt stuff on the
  stack)"

* tag 'nfsd-4.9-1' of git://linux-nfs.org/~bfields/linux:
  nfsd: Fix general protection fault in release_lock_stateid()
  svcrdma: backchannel cannot share a page for send and rcv buffers
  sunrpc: fix some missing rq_rbuffer assignments
  sunrpc: don't pass on-stack memory to sg_set_buf
  nfsd: move blocked lock handling under a dedicated spinlock

Pull btrfs fixes from Chris Mason:
 "Some fixes that Dave Sterba collected.  We held off on these last week
  because I was focused on the memory corruption testing"

* 'for-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: fix WARNING in btrfs_select_ref_head()
  Btrfs: remove some no-op casts
  btrfs: pass correct args to btrfs_async_run_delayed_refs()
  btrfs: make file clone aware of fatal signals
  btrfs: qgroup: Prevent qgroup->reserved from going subzero
  Btrfs: kill BUG_ON in do_relocation

Pull overlayfs fixes from Miklos Szeredi:
 "Fix two more POSIX ACL bugs introduced in 4.8 and add a missing fsync
  during copy up to prevent possible data loss"

* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
  ovl: fsync after copy-up
  ovl: fix get_acl() on tmpfs
  ovl: update S_ISGID when setting posix ACLs

Pull drm fixes from Dave Airlie:
 "Fixes for amdgpu, radeon, intel, imx and virtio-gpu.

  This is a bit larger than I'd like, but I had some stuff I meant to
  send for -rc3 but was waiting for the PAT regression fix to land. So
  this is really fixes for rc3 and rc4 in one go.

  There are a set of fixes for an oops we've been seeing around MST
  display unplug, along with more suspend/resume and shutdown fixes for
  amdgpu, one power management follow on fix for nouveau, and set of imx
  fixes, and a single virtio-gpu regression fix"

* tag 'drm-fixes-for-v4.9-rc4' of git://people.freedesktop.org/~airlied/linux: (54 commits)
  virtio-gpu: fix vblank events
  drm/nouveau/acpi: fix check for power resources support
  drm/i915: Fix SKL+ 90/270 degree rotated plane coordinate computation
  drm/i915: Remove two invalid warns
  drm/i915: Rotated view does not need a fence
  drm/i915/fbc: fix CFB size calculation for gen8+
  drm: i915: Wait for fences on new fb, not old
  drm/i915: Clean up DDI DDC/AUX CH sanitation
  drm/i915: Respect alternate_aux_channel for all DDI ports
  drm/i915/gen9: fix watermarks when using the pipe scaler
  drm/i915: Fix mismatched INIT power domain disabling during suspend
  drm/i915: fix a read size argument
  drm/i915: Use fence_write() from rpm resume
  drm/i915/gen9: fix DDB partitioning for multi-screen cases
  drm/i915: workaround sparse warning on variable length arrays
  drm/i915: keep declarations in i915_drv.h
  drm/amd/powerplay: fix bug get wrong evv voltage of Polaris.
  drm/amdgpu/si_dpm: workaround for SI kickers
  drm/radeon/si_dpm: workaround for SI kickers
  drm/amdgpu: fix s3 resume back, uvd dpm randomly can't disable.
  ...

dw_pcie_iatu_unroll_enabled() reads a dbi_base register.  Reading any
dbi_base register before pp->ops->host_init has been called causes
"imprecise external abort" on platforms like ARTPEC-6, where the PCIe
module is disabled at boot and first enabled in pp->ops->host_init.  Move
dw_pcie_iatu_unroll_enabled() to dw_pcie_setup_rc(), since it is after
pp->ops->host_init, but before pp->iatu_unroll_enabled is actually used.

Fixes: a0601a47 ("PCI: designware: Add iATU Unroll feature")
Tested-by: James Le Cuirot <chewi@gentoo.org>
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Joao Pinto <jpinto@synopsys.com>
Acked-by: Olof Johansson <olof@lixom.net>

Pull KVM updates from Paolo Bonzini:
 "One NULL pointer dereference, and two fixes for regressions introduced
  during the merge window.

  The rest are fixes for MIPS, s390 and nested VMX"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  kvm: x86: Check memopp before dereference (CVE-2016-8630)
  kvm: nVMX: VMCLEAR an active shadow VMCS after last use
  KVM: x86: drop TSC offsetting kvm_x86_ops to fix KVM_GET/SET_CLOCK
  KVM: x86: fix wbinvd_dirty_mask use-after-free
  kvm/x86: Show WRMSR data is in hex
  kvm: nVMX: Fix kernel panics induced by illegal INVEPT/INVVPID types
  KVM: document lock orders
  KVM: fix OOPS on flush_work
  KVM: s390: Fix STHYI buffer alignment for diag224
  KVM: MIPS: Precalculate MMIO load resume PC
  KVM: MIPS: Make ERET handle ERL before EXL
  KVM: MIPS: Fix lazy user ASID regenerate for SMP

Pull MIPS fixes from Ralf Baechle:
 "A set of MIPS fixes for 4.9:

   - lots of fixes for printk continuations
   - six fixes for FP related code.
   - fix max_low_pfn with disabled highmem
   - fix KASLR handling of NULL FDT and KASLR for generic kernels
   - fix build of compressed image
   - provide default mips_cpc_default_phys_base to ignore CPC
   - fix reboot on Malta"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: Fix max_low_pfn with disabled highmem
  MIPS: Correct MIPS I FP sigcontext layout
  MIPS: Fix ISA I/II FP signal context offsets
  MIPS: Remove FIR from ISA I FP signal context
  MIPS: Fix ISA I FP sigcontext access violation handling
  MIPS: Fix FCSR Cause bit handling for correct SIGFPE issue
  MIPS: ptrace: Also initialize the FP context on individual FCSR writes
  MIPS: dump_tlb: Fix printk continuations
  MIPS: Fix __show_regs() output
  MIPS: traps: Fix output of show_code
  MIPS: traps: Fix output of show_stacktrace
  MIPS: traps: Fix output of show_backtrace
  MIPS: Fix build of compressed image
  MIPS: generic: Fix KASLR for generic kernel.
  MIPS: KASLR: Fix handling of NULL FDT
  MIPS: Malta: Fixup reboot
  MIPS: CPC: Provide default mips_cpc_default_phys_base to ignore CPC

Pull parisc updates from Helge Deller:
 "The first three patches are trivial and add some required KERN_CONT,
  ignore the new pkey syscalls on parisc and use the LINUX_GATEWAY_ADDR
  define instead of hardcoded values.

  The two patches from Dave Anglin are important.

  The first one avoids trashing the sr2 and sr3 space registers in the
  Light-weight syscall path. Especially the usage of sr3 is critical
  since it may get trashed by the interrupt handler.

  The second patch is even more important and tagged for stable series.
  It protects one critical section in the syscall entry path by
  disabling local interrupts. Without disabling interrupts, the sr7
  space register may not be in sync with the current stack setup and
  thus an incoming hardware interrupt may destroy memory in random
  userspace areas"

* 'parisc-4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Ignore the pkey system calls for now
  parisc: Use LINUX_GATEWAY_ADDR define instead of hardcoded value
  parisc: Ensure consistent state when switching to kernel stack at syscall entry
  parisc: Avoid trashing sr2 and sr3 in LWS code
  parisc: use KERN_CONT when printing device inventory

Race condition between registering an I2C device driver and
deregistering an I2C adapter device which is assumed to manage that
I2C device may lead to a NULL pointer dereference due to the
uninitialized list head of driver clients.

The root cause of the issue is that the I2C bus may know about the
registered device driver and thus it is matched by bus_for_each_drv(),
but the list of clients is not initialized and commonly it is NULL,
because I2C device drivers define struct i2c_driver as static and
clients field is expected to be initialized by I2C core:

  i2c_register_driver()             i2c_del_adapter()
    driver_register()                 ...
      bus_add_driver()                ...
        ...                           bus_for_each_drv(..., __process_removed_adapter)
      ...                               i2c_do_del_adapter()
    ...                                   list_for_each_entry_safe(..., &driver->clients, ...)
    INIT_LIST_HEAD(&driver->clients);

To solve the problem it is sufficient to do clients list head
initialization before calling driver_register().

The problem was found while using an I2C device driver with a sluggish
registration routine on a bus provided by a physically detachable I2C
master controller, but practically the oops may be reproduced under
the race between arbitraty I2C device driver registration and managing
I2C bus device removal e.g. by unbinding the latter over sysfs:

% echo 21a4000.i2c > /sys/bus/platform/drivers/imx-i2c/unbind
  Unable to handle kernel NULL pointer dereference at virtual address 00000000
  Internal error: Oops: 17 [#1] SMP ARM
  CPU: 2 PID: 533 Comm: sh Not tainted 4.9.0-rc3+ #61
  Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
  task: e5ada400 task.stack: e4936000
  PC is at i2c_do_del_adapter+0x20/0xcc
  LR is at __process_removed_adapter+0x14/0x1c
  Flags: NzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
  Control: 10c5387d  Table: 35bd004a  DAC: 00000051
  Process sh (pid: 533, stack limit = 0xe4936210)
  Stack: (0xe4937d28 to 0xe4938000)
  Backtrace:
  [<c0667be0>] (i2c_do_del_adapter) from [<c0667cc0>] (__process_removed_adapter+0x14/0x1c)
  [<c0667cac>] (__process_removed_adapter) from [<c0516998>] (bus_for_each_drv+0x6c/0xa0)
  [<c051692c>] (bus_for_each_drv) from [<c06685ec>] (i2c_del_adapter+0xbc/0x284)
  [<c0668530>] (i2c_del_adapter) from [<bf0110ec>] (i2c_imx_remove+0x44/0x164 [i2c_imx])
  [<bf0110a8>] (i2c_imx_remove [i2c_imx]) from [<c051a838>] (platform_drv_remove+0x2c/0x44)
  [<c051a80c>] (platform_drv_remove) from [<c05183d8>] (__device_release_driver+0x90/0x12c)
  [<c0518348>] (__device_release_driver) from [<c051849c>] (device_release_driver+0x28/0x34)
  [<c0518474>] (device_release_driver) from [<c0517150>] (unbind_store+0x80/0x104)
  [<c05170d0>] (unbind_store) from [<c0516520>] (drv_attr_store+0x28/0x34)
  [<c05164f8>] (drv_attr_store) from [<c0298acc>] (sysfs_kf_write+0x50/0x54)
  [<c0298a7c>] (sysfs_kf_write) from [<c029801c>] (kernfs_fop_write+0x100/0x214)
  [<c0297f1c>] (kernfs_fop_write) from [<c0220130>] (__vfs_write+0x34/0x120)
  [<c02200fc>] (__vfs_write) from [<c0221088>] (vfs_write+0xa8/0x170)
  [<c0220fe0>] (vfs_write) from [<c0221e74>] (SyS_write+0x4c/0xa8)
  [<c0221e28>] (SyS_write) from [<c0108a20>] (ret_fast_syscall+0x0/0x1c)
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org

When low memory doesn't reach HIGHMEM_START (e.g. up to 256MB at PA=0 is
common) and highmem is present above HIGHMEM_START (e.g. on Malta the
RAM overlayed by the IO region is aliased at PA=0x90000000), max_low_pfn
will be initially calculated very large and then clipped down to
HIGHMEM_START.

This causes crashes when reading /sys/kernel/mm/page_idle/bitmap
(i.e. CONFIG_IDLE_PAGE_TRACKING=y) when highmem is disabled. pfn_valid()
will compare against max_mapnr which is derived from max_low_pfn when
there is no highend_pfn set up, and will return true for PFNs right up
to HIGHMEM_START, even though they are beyond the end of low memory and
no page structs will actually exist for these PFNs.

This is fixed by skipping high memory regions when initially calculating
max_low_pfn if highmem is disabled, so it doesn't get clipped too high.
We also clip regions which overlap the highmem boundary when highmem is
disabled, so that max_pfn doesn't extend into highmem either.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14490/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Complement commit 80cbfad7 ("MIPS: Correct MIPS I FP context
layout") and correct the way Floating Point General registers are stored
in a signal context with MIPS I hardware.

Use the S.D and L.D assembly macros to have pairs of SWC1 instructions
and pairs of LWC1 instructions produced, respectively, in an arrangement
which makes the memory representation of floating-point data passed
compatible with that used by hardware SDC1 and LDC1 instructions, where
available, regardless of the hardware endianness used.  This matches the
layout used by r4k_fpu.S, ensuring run-time compatibility for MIPS I
software across all o32 hardware platforms.

Define an EX2 macro to handle exceptions from both hardware instructions
implicitly produced from S.D and L.D assembly macros.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14477/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Fix a regression introduced with commit 2db9ca0a ("MIPS: Use struct
mips_abi offsets to save FP context") for MIPS I/I FP signal contexts,
by converting save/restore code to the updated internal API.  Start FGR
offsets from 0 rather than SC_FPREGS from $a0 and use $a1 rather than
the offset of SC_FPC_CSR from $a0 for the Floating Point Control/Status
Register (FCSR).

Document the new internal API and adjust assembly code formatting for
consistency.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14476/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Complement commit e50c0a8f ("Support the MIPS32 / MIPS64 DSP ASE.")
and remove the Floating Point Implementation Register (FIR) from the FP
register set recorded in a signal context with MIPS I processors too, in
line with the change applied to r4k_fpu.S.

The `sc_fpc_eir' slot is unused according to our current ABI and the FIR
register is read-only and always directly accessible from user software.

[ralf@linux-mips.org: This is also required because the next commit depends
on it.]
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14475/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>