- 11 Jul, 2012 6 commits
-
-
Scott Wood authored
Similar to how the primary PCI bridge is identified by looking for an isa subnode, we determine whether to apply uli exclusions by looking for a uli subnode. Signed-off-by:
Scott Wood <scottwood@freescale.com> Signed-off-by:
Kumar Gala <galak@kernel.crashing.org>
-
Scott Wood authored
As an alternative incremental starting point to Jia Hongtao's patchset, get the FSL PCI init out of the board files, but do not yet convert to a platform driver. Rather than having each board supply a magic register offset for determining the "primary" bus, we look for which PCI host bridge contains an ISA node within its subtree. If there is no ISA node, normally that would mean there is no primary bus, but until certain bugs are fixed we arbitrarily designate a primary in this case. Conversion to a platform driver and related improvements can happen after this, as the ordering issues are sorted out. Signed-off-by:
-
Shengzhou Liu authored
Enable USB, MMC, SATA, LBC, MTD, NAND, SPI, PCIe, EDAC, VFAT, NFS, etc. Signed-off-by:
Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by:
-
Shengzhou Liu authored
- Enable NAND support - Enable CONFIG_PCI_MSI and CONFIG_MMC_SDHCI_OF Signed-off-by:
-
Xu Jiucheng authored
The board is really P1021RDB-PC, so rename from p1021rdb.* to p1021rdb-pc.* Signed-off-by:
Xu Jiucheng <Jiucheng.Xu@freescale.com> Signed-off-by:
Matthew McClintock <msm@freescale.com> Signed-off-by:
-
Shaohui Xie authored
Currently, BOOKE watchdog code for checking "wdt" and "wdt_period" is in setup_32.c, it cannot be used in 64-bit, so move it to a common place setup-common.c, which will be shared by 32-bit and 64-bit. Also, replace the simple_strtoul with kstrtol. Signed-off-by:
Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by:
-
- 10 Jul, 2012 34 commits
-
-
Zhicheng Fan authored
Add device tree nodes to enable ucc uart support on P1025RDB. Signed-off-by:
Zhicheng Fan <B32736@freescale.com> Signed-off-by:
-
Shawn Guo authored
Freescale PowerPC SoCs share a number of IP blocks with Freescale ARM/IMX SoCs, FlexCAN, SSI, FEC, eSDHC, USB, etc. There are some effort consolidating those drivers to make them work for both architectures. One outstanding difference between two architectures is ARM/IMX will turn off module clocks during platform initialization for power saving and expects drivers manage clocks using clk API, while PowerPC mostly does not do that, and thus does not always build in clk API. Listing all those driver Kconfig options in "select PPC_CLOCK if" seems not scalable for long term maintenance, and could easily introduce Kconfig recursive dependency. This patch chooses to select PPC_CLOCK unconditionally for FSL_SOC to always build clk API for PowerPC in. Signed-off-by:
Shawn Guo <shawn.guo@linaro.org> Signed-off-by:
-
Kokoris, Ioannis authored
QE Microcode Initialization using qe_upload_microcode() does not work on P1021 if the IRAM-Ready register is not set after the microcode upload. Add a definition for the "I-RAM Ready" register and sets it upon microcode upload completion. Signed-off-by:
Ioannis Kokkoris <ioannis.kokoris@siemens-enterprise.com> Signed-off-by:
-
Jia Hongtao authored
With 2-cell format interrupts of MSI PCIe ethernet card can not work. Signed-off-by:
Li Yang <leoli@freescale.com> Signed-off-by:
Jia Hongtao <B38951@freescale.com> Signed-off-by:
-
Jia Hongtao authored
The issue log on core1 is: root@mpc8572ds:~# ifconfig eth0 10.192.208.244 net eth0: could not attach to PHY SIOCSIFFLAGS: No such device To attach PHY node mdio@24520 should not be disabled in dts of core1. Because all PHYs are controlled through this node as follows: mdio@24520 { phy0: ethernet-phy@0 { interrupts = <10 1 0 0>; reg = <0x0>; }; phy1: ethernet-phy@1 { interrupts = <10 1 0 0>; reg = <0x1>; }; phy2: ethernet-phy@2 { interrupts = <10 1 0 0>; reg = <0x2>; }; phy3: ethernet-phy@3 { interrupts = <10 1 0 0>; reg = <0x3>; }; tbi0: tbi-phy@11 { reg = <0x11>; device_type = "tbi-phy"; }; }; Signed-off-by: -
Shaohui Xie authored
CONFIG_FSL_BOOKE is only defined in 32-bit, CONFIG_PPC_FSL_BOOK3E is defined in both 32-bit and 64-bit, so use CONFIG_PPC_FSL_BOOK3E to make driver work in 32-bit & 64-bit. Signed-off-by:
-
Varun Sethi authored
We should use the MPIC_LARG_VECTORS flag while intializing the MPIC. This prevents us from eating in to hardware vector number space (MSIs) while setting up internal sources. Signed-off-by:
Varun Sethi <Varun.Sethi@freescale.com> Signed-off-by:
-
Liu Yu authored
So that we can call it when improving SPE switch like book3e did for fp switch. Signed-off-by:
Liu Yu <yu.liu@freescale.com> Signed-off-by:
Olivia Yin <hong-hua.yin@freescale.com> Signed-off-by:
-
Prabhakar Kushwaha authored
BSC9131RDB is a Freescale reference design board for BSC9131 SoC. The BSC9131 is integrated SoC that targets Femto base station market. It combines Power Architecture e500v2 and DSP StarCore SC3850 core technologies with MAPLE-B2F baseband acceleration processing elements. The BSC9131 SoC includes the following function and features: . Power Architecture subsystem including a e500 processor with 256-Kbyte shared L2 cache . StarCore SC3850 DSP subsystem with a 512-Kbyte private L2 cache . The Multi Accelerator Platform Engine for Femto BaseStation Baseband Processing (MAPLE-B2F) . A multi-standard baseband algorithm accelerator for Channel Decoding/Encoding, Fourier Transforms, UMTS chip rate processing, LTE UP/DL Channel processing, and CRC algorithms . Consists of accelerators for Convolution, Filtering, Turbo Encoding, Turbo Decoding, Viterbi decoding, Chiprate processing, and Matrix Inversion operations . DDR3/3L memory interface with 32-bit data width without ECC and 16-bit with ECC, up to 400-MHz clock/800 MHz data rate . Dedicated security engine featuring trusted boot . DMA controller . OCNDMA with four bidirectional channels . Interfaces . Two triple-speed Gigabit Ethernet controllers featuring network acceleration including IEEE 1588. v2 hardware support and virtualization (eTSEC) . eTSEC 1 supports RGMII/RMII . eTSEC 2 supports RGMII . High-speed USB 2.0 host and device controller with ULPI interface . Enhanced secure digital (SD/MMC) host controller (eSDHC) . Antenna interface controller (AIC), supporting three industry standard JESD207/three custom ADI RF interfaces (two dual port and one single port) and three MAXIM's MaxPHY serial interfaces . ADI lanes support both full duplex FDD support and half duplex TDD support . Universal Subscriber Identity Module (USIM) interface that facilitates communication to SIM cards or Eurochip pre-paid phone cards . TDM with one TDM port . Two DUART, four eSPI, and two I2C controllers . Integrated Flash memory controller (IFC) . TDM with 256 channels . GPIO . Sixteen 32-bit timers The DSP portion of the SoC consists of DSP core (SC3850) and various accelerators pertaining to DSP operations. BSC9131RDB Overview ---------------------- BSC9131 SoC 1Gbyte DDR3 (on board DDR) 128Mbyte 2K page size NAND Flash 256 Kbit M24256 I2C EEPROM 128 Mbit SPI Flash memory USB-ULPI eTSEC1: Connected to RGMII PHY eTSEC2: Connected to RGMII PHY DUART interface: supports one UARTs up to 115200 bps for console display Linux runs on e500v2 core and access some DSP peripherals like AIC Signed-off-by:Ramneek Mehresh <ramneek.mehresh@freescale.com> Signed-off-by:
Priyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by:
Akhil Goyal <Akhil.Goyal@freescale.com> Signed-off-by:
Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by:
Rajan Srivastava <rajan.srivastava@freescale.com> Signed-off-by:
Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by:
-
Timur Tabi authored
This reverts commit 96cc017c. The P3060 was cancelled before it went into production, so there's no point in supporting it. Signed-off-by:
Timur Tabi <timur@freescale.com> Signed-off-by:
-
Timur Tabi authored
In order to enable the DIU video controller on the P1022DS, the FPGA needs to be switched to "indirect mode", where the localbus is disabled and the FPGA is accessed via writes to localbus chip select signals CS0 and CS1. To obtain the address of CS0 and CS1, the platform driver uses an "indirect pixis mode" device tree node. This node assumes that the localbus 'ranges' property is sorted in chip-select order. That is, reg value 0 maps to CS0, reg value 1 maps to CS1, etc. This is how the 'ranges' property is supposed to be arranged. Unfortunately, the 'ranges' property is often mis-arranged, and not just on the P1022DS. Linux normally does not care, since it does not program the localbus. But the indirect-mode code on the P1022DS does care. The "proper" fix is to have U-Boot fix the 'ranges' property, but this would be too cumbersome. The names and 'reg' properties of all the localbus devices would also need to be updated, and determining which localbus device maps to which chip select is board-specific. Instead, we determine the CS0/CS1 base addresses the same way that U-boot does -- by reading the BRx registers directly and mapping them to physical addresses. This code is simpler and more reliable, and it does not require a U-boot or device tree change. Since the indirect pixis device tree node is no longer needed, the node is deleted from the DTS. Signed-off-by:
-
Shaohui Xie authored
NAND on p2041 uses CS1 as chip select. Signed-off-by:
-
Paul Gortmaker authored
This reference board dates back to 2004, and is largely a legacy EOL product. The MPC8560 is a pre e500v2 CPU. The SBC8548 is a more modern, better e500v2 target for people to use as a reference board with today's kernels, should they require one. Removing support for it will also allow us to remove some sbc8560 specific quirk handling in 8250 UART code, and some MTD mapping support. Cc: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by:
Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by:
-
Tang Yuantian authored
Signed-off-by:
Jin Qing <b24347@freescale.com> Signed-off-by:
Tang Yuantian <Yuantian.Tang@freescale.com> Signed-off-by:
-
Tang Yuantian authored
The p1024rdb has the similar feature as the p1020rdb. Therefore, p1024rdb use the same platform file as the p1/p2 rdb board. Overview of P2020RDB platform - DDR3 1G - NOR flash 16M - 3 Ethernet interfaces - NAND Flash 32M - SPI EEPROM 16M - SD/MMC - 2 USB ports - 4 TDM ports Signed-off-by:
-
Gustavo Zacarias authored
Add EEPROM to the P1010RDB device tree. The 24c01 acts as a memory SPD so it shouldn't be overwritten without care. The 24c256 is a general purpose memory. Signed-off-by:
Gustavo Zacarias <gustavo@zacarias.com.ar> Signed-off-by:
-
Sebastian Andrzej Siewior authored
This reverts commit 0c00f656. The initial commit was my fault. There are two boards out there: P2020RDB and P2020RDB-PC. I wasn't aware of that and assumed that I have a RDB board in front of me while I the RDB-PC. This patch makes it work for the RDB-PC variant and breaks it for the RDB. Now there is a device tree file available for the RDB-PC which was not there earlier. So with this revert, everything gets back to normal :) Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
-
Holger Brunck authored
Add spi support for mgcoge into the platform code and the dts file. Additionaly SPIDEV is switched on in the defconfig and the updates for the newer kernel version are committed. The SPI interface is used to drive the Maxim DS3106 clock chip. Signed-off-by:
Holger Brunck <holger.brunck@keymile.com> cc: Heiko Schocher <hs@denx.de> Signed-off-by:
-
Holger Brunck authored
Switch on UBIFS, HOTPLUG and TIPC and update the config to the latest kernel version. Signed-off-by:
-
Christian Herzig authored
Fix RGMII workaround code in km83xx.c for MPC8360E and MPC8358E that it correctly identifes all affected SoC chip models and applies the workarounds appropriate for 2.0 and 2.1 revisions as per Freescale MPC8360ECE Errata document Rev.5(9/2011) item QE_ENET10. Signed-off-by:
Christian Herzig <christian.herzig@keymile.com> Signed-off-by:
-
Holger Brunck authored
Signed-off-by:
-
Jerry Huang authored
Add the RTC support into the p1022ds device tree Signed-off-by:
Jerry Huang <Chang-Ming.Huang@freescale.com> Acked-by:
-
Shengzhou Liu authored
Enable MTD/NOR/NAND options by default in mpc85xx_defconfig and mpc85xx_smp_defconfig to support NOR, NAND flash. Signed-off-by:
-
Kim Phillips authored
At least for crypto/IPSec, doing so provides users with a better performance experience out of the box. Signed-off-by:
Kim Phillips <kim.phillips@freescale.com> Signed-off-by:
-
Matias Garcia authored
Change quirk_fsl_pcie_header from __init to __devinit to ensure if we have a runtime access (like via an FPGA being loaded after boot on the PCIe link) that we dont access randomly freed memory. Signed-off-by:
Matias Garcia <mgarcia@rossvideo.com> Signed-off-by:
-
Michael Ellerman authored
Matt added BPF_JIT support in commit 0ca87f05, but currently none of our defconfigs build it. Turn that sucker on. Signed-off-by:
Michael Ellerman <michael@ellerman.id.au> Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org>
-
Anton Blanchard authored
Add the ability to inject IOMMU faults. We enable this per device via a fail_iommu sysfs property, similar to fault injection on other subsystems. An example: ... 0003:01:00.1 Ethernet controller: Emulex Corporation OneConnect 10Gb NIC (be3) (rev 02) To inject one error to this device: echo 1 > /sys/bus/pci/devices/0003:01:00.1/fail_iommu echo 1 > /sys/kernel/debug/fail_iommu/probability echo 1 > /sys/kernel/debug/fail_iommu/times As feared, the first failure injected on the be3 results in an unrecoverable error, taking down both functions of the card permanently: be2net 0003:01:00.1: Unrecoverable error in the card Signed-off-by:
Anton Blanchard <anton@samba.org> Signed-off-by:
-
Anton Blanchard authored
The DMA API debug code has hooks to verify all DMA entries have been freed at time of hot unplug. We need to call dma_debug_add_bus for this to work. Signed-off-by:
-
Anton Blanchard authored
Similar to PCI, separate the bus probe from device probe. This allows us to attach bus notifiers for DMA debug and IOMMU fault injection before devices have been probed. Signed-off-by:
-
Anton Blanchard authored
During boot we see a number of these warnings: vio 30000000: Warning: IOMMU dma not supported: mask 0xffffffffffffffff, table unavailable The reason for this is that we set IOMMU properties for all VIO devices even if they are not DMA capable. Only set DMA ops, table and mask for devices with a DMA window. Signed-off-by:
-
Michael Neuling authored
Signed-off-by:
Michael Neuling <mikey@neuling.org> Acked-by:
Gavin Shan <shangw@linux.vnet.ibm.com> Signed-off-by:
-
Anton Blanchard authored
We use SIAR or regs->nip for the instruction pointer depending on the PMU configuration, but we always use regs->nip in the callchain. Use perf_instruction_pointer so the backtrace is consistent. Signed-off-by:
-
Anton Blanchard authored
At the moment we always use the SIAR if the PMU supports continuous sampling. Unfortunately the SIAR and the PMU exception are not synchronised for non marked events so we can end up with callchains that dont make sense. The following patch checks the HV and PR bits for samples coming from userspace and always uses pt_regs for them. Userspace will never have interrupts off so there is no real advantage to using the SIAR for non marked events in userspace. I had experimented with a patch that did a similar thing for kernel samples but we lost a significant amount of information. I was unable to profile any of our early exception code for example. Signed-off-by:
-
Anton Blanchard authored
The logic to choose whether to use the SIAR or get the information out of pt_regs is going to get more complicated, so do it once in perf_read_regs. We overload regs->result which is gross but we are already doing it with regs->dsisr. Signed-off-by:
-
