Commit 88452565 ("PCI: clean up resource
alignment management") didn't set the alignment information for the
cardbus window resources, causing their subsequent allocations to fail
miserably with a message like

  yenta_cardbus 0000:15:00.0: device not available because of BAR 7 [100:1ff] collisions
  yenta_cardbus: probe of 0000:15:00.0 failed with error -16

or similar.

This fixes it and clarifies the code a bit too (we used to have to use
the insane PCI bridge alignment logic that put the alignment in the
"start" field, this makes it use the slightly easier-to-understand
size-based alignment, and allows us to set the resource start to zero
until it gets allocated).
Reported-and-tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Prevent bus_remove_device() from crashing if dev->knode_bus has not been
initialized before it's called.

This can happen if the device_add() ended up breaking out early due to
an error, for example.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Do not refuse to actually register children of suspended devices,
but still warn about attempts to do that.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] run drivers/misc/sgi-xp through scripts/checkpatch.pl
  [IA64] run rest drivers/misc/sgi-xp through scripts/Lindent
  [IA64] run some drivers/misc/sgi-xp through scripts/Lindent
  [IA64] move XP and XPC to drivers/misc/sgi-xp
  [IA64] minor irq handler cleanups
  [IA64] simplify notify hooks in mca.c
  [IA64] do notify DIE_MCA_MONARCH_PROCESS for each monarchs
  [IA64] disable interrupts on exit of ia64_trace_syscall

Use offset type consistently.
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6:
  SELinux fixups needed for preemptable RCU from -rt
  SELinux: no BUG_ON(!ss_initialized) in selinux_clone_mnt_opts

Addressed issues raised by scripts/checkpatch.pl. Removed unnecessary curly
braces. Eliminated uses of volatiles and use of kernel_thread() and daemonize().
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

Ran patches through scripts/Lindent (part 2).
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

Ran patches through scripts/Lindent (part 1).
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

Move XPC and XPNET from arch/ia64/sn/kernel to drivers/misc/sgi-xp.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
  i2c: Fix platform driver hotplug/coldplug
  i2c: New driver for the SuperH Mobile I2C bus controller
  i2c/scx200_acb: Don't use 0 as NULL pointer
  i2c-bfin-twi: Fix mismatch in add timer and delete timer
  i2c-bfin-twi: Just let i2c-bfin-twi driver depends on BLACKFIN
  i2c-bfin-twi: Use simpler comment headers and strip out information that is maintained in the scm's log
  i2c-bfin-twi: Cleanup driver descriptions, versions and some module useful information
  i2c-bfin-twi: Add missing pin mux operation
  i2c-bfin-twi: Add platform_resource interface to support multi-port TWI controllers
  i2c-bfin-twi: Add repeat start feature to avoid break of a bundle of i2c master xfer operation
  i2c: Remove trailing whitespaces in busses/Kconfig
  i2c: Replace remaining __FUNCTION__ occurrences
  i2c: Renesas SH7760 I2C master driver
  i2c-dev: Split i2cdev_ioctl
  i2c-ibm_iic: Support building as an of_platform driver
  i2c-ibm_iic: Change the log levels
  i2c: Add platform driver on top of the new pca-algorithm
  i2c-algo-pca: Extend for future drivers
  i2c-algo-pca: Remove trailing whitespaces and unnecessary UTF
  i2c: Remove the algorithm drivers from the config menu

Add missing kernel-doc in kernel/sched.c:

Warning(linux-2.6.25-git3//kernel/sched.c:7044): No description found for parameter 'span'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm:
  dlm: linux/{dlm,dlm_device}.h: cleanup for userspace
  dlm: common max length definitions
  dlm: move plock code from gfs2
  dlm: recover nodes that are removed and re-added
  dlm: save master info after failed no-queue request
  dlm: make dlm_print_rsb() static
  dlm: match signedness between dlm_config_info and cluster_set

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: Suppress hidinput for Samsung IR control
  HID: remove 60x GTCO devices from blacklist
  HID: export headers properly
  HID: WiseGroup 866 Dual Joypad needs output reports quirk
  HID: ThrustMaster FF driver is no longer experimental
  HID: Logitech diNovo Mini pad support
  HID: fix race between open() and disconnect() in usbhid
  HID: make hid_input_field and usbhid_modify_dquirk static
  HID: pass numbered reports properly to hidraw
  HID: fix misplaced rdesc quirk
  HID: force feedback driver for Logitech Rumblepad 2
  HID: move wait from hid to usbhid
  HID: make function from dbg_hid
  HID: fix sparse warnings
  HID: only dump report traffic with debug level 2
  HID: patch to add NOGET for DMI/Acomdata
  HID: Sunplus Wireless Desktop needs report descriptor fixup
  HID: quirk for MS Wireless Desktop Receiver (model 1028)
  HID: fixup fullspeed interval on highspeed Afatech DVB-T IR kbd
  HID: fix build failure in hiddev_ioctl with gcc 3.2

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-udf-2.6: (41 commits)
  udf: use crc_itu_t from lib instead of udf_crc
  udf: Fix compilation warnings when UDF debug is on
  udf: Fix bug in VAT mapping code
  udf: Add read-only support for 2.50 UDF media
  udf: Fix handling of multisession media
  udf: Mount filesystem read-only if it has pseudooverwrite partition
  udf: Handle VAT packed inside inode properly
  udf: Allow loading of VAT inode
  udf: Fix detection of VAT version
  udf: Silence warning about accesses beyond end of device
  udf: Improve anchor block detection
  udf: Cleanup anchor block detection.
  udf: Move processing of virtual partitions
  udf: Move filling of partition descriptor info into a separate function
  udf: Improve error recovery on mount
  udf: Cleanup volume descriptor sequence processing
  udf: fix anchor point detection
  udf: Remove declarations of arrays of size UDF_NAME_LEN (256 bytes)
  udf: Remove checking of existence of filename in udf_add_entry()
  udf: Mark udf_process_sequence() as noinline
  ...

While looking at the implementation of the Ram backed block device
driver, I stumbled across a write-only local variable, which makes
little sense, so I assume it should actually work like this:
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Since 43cc71ee, the platform
modalias is prefixed with "platform:". Add MODULE_ALIAS() to the
hotpluggable I2C platform drivers, to allow module auto loading.

[ db: add some more drivers ]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

This is V5 of the SuperH Mobile I2C Controller Driver. A simple Master
only driver for the I2C block included in processors such as sh7343,
sh7722 and sh7723. Tested on a sh7722 MigoR using a rs5c732b rtc.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Don't use 0 as NULL pointer.

Spotted by sparse.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Move init_completion to just before i2c transfer.
http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=3385Signed-off-by: Hans Schillstrom <hans.schillstrom@shlsys.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Simply use "depends on BLACKFIN" (which is technically correct) and just
document which machines have the device.
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

i2c-bfin-twi: Use simpler comment headers and strip out information that is maintained in the scm's log
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Blackfin TWI controller hardware pin should be requested from GPIO port controller
Before BF54x, there is no need to do this. But as long as BF54x and BF52x
are supported by this generic driver, the missing pin mux operation should be
added.
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

 - Dynamic alloc the resource of TWI driver data according to board information
 - TWI register read/write accessor based on dynamic regs_base
 - Support TWI0/TWI1 for BF54x
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

 - Create a new mode TWI_I2C_MODE_REPEAT.
 - No change to smbus operation.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

__FUNCTION__ is gcc-specific, use __func__.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Driver for I2C interfaces in master mode on SH7760.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Split the handling of the I2C_RDWR and I2C_SMBUS ioctls to their own
functions. This limits the stack usage, saves one level of indentation
and makes the code more readable.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

This patch allows the i2c-ibm_iic driver to be built either as an ocp 
driver or an of_platform driver. This allows it to run under the powerpc 
arch but maintains backward compatibility with the ppc arch.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Change the log levels based on feedback from linxppc-dev.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Tested on a blackfin.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

The separation between algorithm and adapter was unsharp at places. This was
partly hidden by the fact, that the ISA-driver allowed just one instance and
had all private data in static variables. This patch makes neccessary
preparations to add a platform driver on top of the algorithm, while still
supporting ISA. Note: Due to lack of hardware, the ISA-driver could not be
tested except that it builds.

Concerning the core struct i2c_algo_pca_data:

- A private data field was added, all hardware dependant data may go here.
  Similar to other algorithms, now a pointer to this data is passed to the
  adapter's functions. In order to make as less changes as possible to the
  ISA-driver, it leaves the private data empty and still only uses its static
  variables.

- A "reset_chip" function pointer was added; such a functionality must come
  from the adapter, not the algorithm.

- use a variable "i2c_clock" instead of a function pointer "get_clock",
  allowing for write access to a default in case a wrong value was supplied.

In the algorithm-file:

- move "i2c-pca-algo.h" into "linux/i2c-algo-pca.h"
- now using per_instance timeout values (i2c_adap->timeout)
- error messages specify the device, not only the driver name
- restructure initialization to easily support "i2c_add_numbered_adapter"
- drop "retries" and "own" (i2c address) as they were unused

(The state-machine for I2C-communication was not touched.)

In the ISA-driver:

- adapt to new algorithm
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Remove trailing whitespaces to make further patches more readable.  Also remove
an unnecessary UTF-char for simplicity ("us" for microseconds is fine enough).
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

The algorithm drivers are helper drivers that are selected automatically
as needed. There's no point in listing them in the config menu, it can
only confuse users and waste their time.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

- remove unused 'irq' argument from pfm_do_interrupt_handler()

- remove pointless cast to void*

- add KERN_xxx prefix to printk()

- remove braces around singleton C statement

- in tioce_provider.c, start tioce_dma_consistent() and
  tioce_error_intr_handler() function declarations in column 0

This change's main purpose is to prepare for the patchset in
jgarzik/misc-2.6.git#irq-remove, that explores removal of the
never-used 'irq' argument in each interrupt handler.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

There are many notify_die() and almost all take same style with
ia64_mca_spin().  This patch defines macros and replace them all,
to reduce lines and to improve readability.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

There are 3 hooks in MCA handler, but this DIE_MCA_MONARCH_PROCESS
event does not notified other than for the first monarch.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

While testing with CONFIG_VIRT_CPU_ACCOUNTING=y, I found that
I occasionally get very huge system time in some threads.

So I dug the issue and finally noticed that it was caused
because of an interrupt which interrupt in the following window:

> [arch/ia64/kernel/entry.S: (!CONFIG_PREEMPT && CONFIG_VIRT_CPU_ACCOUNTING)]
>
> ENTRY(ia64_leave_syscall)
>    :
> (pUStk) rsm psr.i
>         cmp.eq pLvSys,p0=r0,r0          // pLvSys=1: leave from syscall
> (pUStk) cmp.eq.unc p6,p0=r0,r0          // p6 <- pUStk
> .work_processed_syscall:
>         adds r2=PT(LOADRS)+16,r12
> (pUStk) mov.m r22=ar.itc                        // fetch time at leave
>         adds r18=TI_FLAGS+IA64_TASK_SIZE,r13
>         ;;
> <<< window: from here >>>
> (p6)    ld4 r31=[r18]  // load current_thread_info()->flags
>         ld8 r19=[r2],PT(B6)-PT(LOADRS)
>         adds r3=PT(AR_BSPSTORE)+16,r12
>         ;;
>         mov r16=ar.bsp
>         ld8 r18=[r2],PT(R9)-PT(B6)
> (p6)    and r15=TIF_WORK_MASK,r31  // any work other than TIF_SYSCALL_TRACE?
>         ;;
>         ld8 r23=[r3],PT(R11)-PT(AR_BSPSTORE)
> (p6)    cmp4.ne.unc p6,p0=r15, r0               // any special work pending?
> (p6)    br.cond.spnt .work_pending_syscall
>         ;;
>         ld8 r9=[r2],PT(CR_IPSR)-PT(R9)
>         ld8 r11=[r3],PT(CR_IIP)-PT(R11)
> (pNonSys) break 0 // bug check: we shouldn't be here if pNonSys is TRUE!
>         ;;
>         invala
> <<< window: to here >>>
>         rsm psr.i | psr.ic // turn off interrupts and interruption collection

If pUStk is true, it means we are going to return user mode, hence we fetch
ar.itc to get time at leave from system.
It seems that it is not possible to interrupt the window if pUStk is true,
because interrupts are disabled early.  And also disabling interrupt makes
sense because it is safe for referring current_thread_info()->flags.

However interrupting the window while pUStk is true was possible.
The route was:
ia64_trace_syscall
-> .work_pending_syscall_end
-> .work_processed_syscall
Only in case entering the window from this route, interrupts are enabled
during in the window even if pUStk is true.  I suppose interrupts must be
disabled here anyway if pUStk is true.
I'm not sure but afraid that what kind of bad effect were there, other
than crazy system time which I found.

FYI, there was a commit 6f6d7582 that
points out a bug at same point(exit of ia64_trace_syscall) in 2006.
It can be said that there was an another bug.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>