Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>

Merge branch 'for-2.6.40' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound-2.6 into topic/asoc

Merge branch 'for-2.6.40' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/asoc-2.6 into topic/asoc

Also fix the maximum value for the capture volume control.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Model the power supply for the digital core as a DAPM_SUPPLY widget. This allows
to cleanup the code a bit.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The SSM2603 is mostly register compatible with the SSM2602 and can be supported
by the current driver without any changes.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The SSM2604 is basically a lightweight variant of the SSM2602 with a compatible
register layout. Thus we can easily support both devices by the same driver,
by providing a slightly set of controls, widgets and routes.

Compared to the SSM2602 the SSM2604 has no microphone input and no headphone
output.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

It is not required to have the codec powered at this stage and DAPM will power
the ADC and DAC down again after probe has run anyway.
Thus we avoid some unnecessary writes by this change.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Some of the values in the default register cache did not represent the codecs
state after reset. This patch fixes it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Define POWER_OFF_ON_STANDBY cause trobles when trying to get some
sound from codec because code for bias setup was not compiled
(define wasn't defined). This define was removed in commit:
cc3202f5 but again introduced by commit: f0fba2ad which then
completely break codec functionality so remove it again.
Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

Those are leftovers from a pre-multicomponent era.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

There are currently two controls which allow selecting the capture source, one
as a normal control, the other as part of a DAPM_MUX widget.
Remove the normal control.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Drop unused field from the coeff struct, precalculate the srate register at
compile-time and cleanup up the naming.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

reg_cache_size is supposed to be the number of elements in the register cache,
not the size in bytes.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The 'Mic Boost2' control's shift was off by one and thus was not working.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

Annotate the i2c probe and remove functions with __devinit and __devexit.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

If we specifically want to write a block of data to the hw bypassing the
cache, then allow this to happen inside snd_soc_hw_bulk_write_raw().
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This allows to create DAPM routes depending on those widgets in the
codecs probe function.  This is helpful when supporting similar codecs
with minor differences in the DAPM routing with the same driver.

Something similar has already been done for cards in commit
a841ebb9 (ASoC: Create card DAPM widgets early so they can be used in
callbacks).
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: xingchao <xingchao.wang@intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Actually the current code is perfectly sensible given the hardware.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

Gives finer grained power management.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

Merge branch 'topic/asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6 into for-2.6.40

The move over to exposing snd_soc_register_card() let the initialisation
of the driver data we use to find the card in PM operations go AWOL. Fix
this by setting the driver data when we register the card.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

Control sharing is enabled when two widgets include pointers to the
same kcontrol_new in their definition. Specifically:

static const struct snd_kcontrol_new adcinput_mux =
	SOC_DAPM_ENUM("ADC Input", adcinput_enum);

static const struct snd_soc_dapm_widget wm8903_dapm_widgets[] = {
  SND_SOC_DAPM_MUX("Left ADC Input", SND_SOC_NOPM, 0, 0, &adcinput_mux),
  SND_SOC_DAPM_MUX("Right ADC Input", SND_SOC_NOPM, 0, 0, &adcinput_mux),
};

This is useful when a single register bit or field affects multiple
muxes at once. The common case is to have separate control bits or
fields for each mux (channel). An alternative way of looking at this
is that the mux is a stereo (or even n-channel) mux, rather than
independant mono muxes.

Without this change, a separate kcontrol will be created for each
DAPM_MUX. This has the following disadvantages:

* Confuses the user/programmer with redundant controls that don't
  map to separate hardware.

* When one of the controls is changed, ASoC fails to update the DAPM
  logic for paths solely affected by the other controls impacted by
  the same register bits. This causes some paths not to be correctly
  powered up or down. Prior to this change, to work around this, the
  user or programmer had to manually toggle all duplicate controls away
  from the intended setting, and then back to it.

Control sharing implies that the control is named based on the
kcontrol_new itself, not any of the widgets that are affected by it.

Control sharing is implemented by: When creating kcontrols, if a
kcontrol does not yet exist for a particular kcontrol_new, then a new
kcontrol is created with a list of widgets containing just a single
entry. This is the normal case. However, if a kcontrol does already
exists for the given kcontrol_new, the current widget is simply added
to that kcontrol's list of affected widgets.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

A future change will allow multiple widgets to be affected by the same
control. For example, a single register bit that controls separate muxes
in both the L and R audio paths.

This change updates the code that handles relevant controls to be able
to iterate over a list of affected widgets. Note that only the put
functions need significant modification to implement the iteration; the
get functions do not need to iterate, nor unify the results, since all
affected widgets reference the same kcontrol.

When creating the list of widgets, always create a 1-sized list, since
the control sharing is not implemented in this change.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Future changes will need reference to the kcontrol created for a given
kcontrol_new. Store the created kcontrol values now.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

A future change will modify struct snd_soc_dapm_widget to store the
actual kcontrol pointers for each kcontrol_new in a field named
kcontrols. Rename the existing kcontrols field to enable this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The i2s shutdown callback has the check whether it should be disabled reversed.
Currently it is disabled if another stream is still active, but kept enabled if
the last stream is closed. This patch fixes it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Remove the DAPM debugfs entries before freeing the context's widgets, otherwise a
use after free situation might occur.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Currently debugfs entries for a DAPM widgets are only added in
snd_soc_dapm_debugfs_init. If a widget is added later (for example in the
dai_link's probe callback) it will not show up in debugfs.
This patch moves the creation of the widget debugfs entry to
snd_soc_dapm_new_widgets where it will be added after the widget has been
properly instantiated.

As a side-effect this will also reduce the number of times the DAPM widget list
is iterated during a card's instantiation.

Since it is possible that snd_soc_dapm_new_widgets is invoked form the codecs or
cards probe callbacks, the creation of the debugfs dapm directory has to be
moved before these are called.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Move the creation of the DAPM debugfs directory to snd_soc_dapm_debugfs_init
instead of having the same duplicated code in both codec and card DAPM setup.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Free the card's DAPM context when the card is removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The enum texts are supposed to be const char * const [].  Without the
second const, it gets compile warnings like
    sound/soc/codecs/max98095.c:607:2: warning: initialization discards qualifiers from pointer target type
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>