Add vdd-supply as smps12_reg for cpu0.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add vdd-supply as smps12_reg for cpu0.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add vdd-supply as smps12_reg for cpu0.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add vdd-supply as smps123_reg for cpu0.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add vdd-supply as smps12_reg for cpu0.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

After ti-opp-supply driver is in place to provide AVS Class0 and abb
regulator scaling support let's enable 1.5GHz for the cpu.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add the OPP supply node for the MPU voltage rail to provide the
information needed by the ti-opp-supply driver to enable AVS Class 0.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add a vbb-supply phandle to the cpus node and also add an additional
triplet of voltages for each OPP in the operating-points-v2 table to
make use of the multi regulator support in the OPP core and provide the
vbb regulator for use by the ti-opp-supply driver.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

BeagleBone Blue: can: enable the dedicated can connector.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Cc: Jason Kridner <jkridner@beagleboard.org>
Cc: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

BeagleBone Blue: usarts: enable all the dedicated usart connectors.

DSM2/uart4: on the Blue, this is a recieve only interface.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Cc: Jason Kridner <jkridner@beagleboard.org>
Cc: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use the correct IRQ gpio pin on the BeagleBone Blue to allow the
wl1835 wireless module to actually work.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Cc: Jason Kridner <jkridner@beagleboard.org>
Cc: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Since SoC specific compatible strings are used for PCIe in
dra74x.dtsi and dra72x.dtsi, remove the compatible property
from dra7.dtsi which uses the deprecated compatible string.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

DRA76 EVM has a 4-lane PCIe connector and DRA76 can support x2 lanes.
Enable both the PCIe lanes here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use dra72 specific compatible string for PCIe while preserving
the older compatible.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use dra74 specific compatible string for PCIe while preserving
the older compatible. While at that add a new label for the
2nd instance of pcie.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

ti,syscon-lane-sel and ti,syscon-lane-conf properties specific to enable
PCIe x2 lane mode are added here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

am574x-idk is similar to am572x-idk with am574x SoC. So create
a common file for both evms and include SoC dtsi as needed.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Hook dcdc2 as the cpu0-supply.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

AM437x IDK has a TPS386000 supply voltage supervisor on the VDD_MPU rail
set to trigger undervoltage condition at 0.96V. Because of this, OPP50,
which is normally configured to 300MHz at 0.95V, must be disabled to
avoid triggering the undervoltage condition. Also mark OPP100 as the
suspend-opp as it is now our lowest OPP.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We can remove the unnecessary "omapdss," prefix because
the omapdrm driver takes care of it when matching with
the driver table.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Official vendor string is now "tpo" and not "toppoly".

Requires patch "omapdrm: panel: fix compatible vendor string for td028ttec1"
so that the driver understands both.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add basic panel support for the Nokia N950. It must be tweaked a
little bit later, since the panel was built into the device
upside-down. Also the first 5 and the last 5 pixels are covered
by plastic.
Signed-off-By: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This improves LCD support for the Droid 4.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Due to a mistake in documentation the DS0_PULL_UP_DOWN_EN macro was
mistakenly defined as an active high bit, however setting the bit
actually disables the internal pull resistor on the pin, so correct this
macro and introduce a new DS0_PULL_UP_DOWN_DIS macro with the proper bit
value set now that the documentation has been updated.

Change based on AM437x Techninal Reference Manual SPRUHL7G Revised June
2017 Section 7.2.1.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

With the backlight phandle the driver can manage the backlight on/off in
sync with the panel enable/disable.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

With the backlight phandle the driver can manage the backlight on/off in
sync with the panel enable/disable.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

With the backlight phandle the driver can manage the backlight on/off in
sync with the panel enable/disable.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:

Warning (unit_address_format): Node /XXX unit name should not have
leading "0x"

and

Warning (unit_address_format): Node /XXX unit name should not have
leading 0s

Converted using the following command:

$ find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec \
sed -i -e "s/@\([0-9a-fA-FxX\.;:#]+\)\s*{/@\L\1 {/g" \
-e "s/@0x\(.*\) {/@\1 {/g" -e "s/@0+\(.*\) {/@\1 {/g" {} +^C

For simplicity, two sed expressions were used to solve each warnings
separately.

To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before
the the opening curly brace:

https://elinux.org/Device_Tree_Linux#Linux_conventions

This will solve as a side effect warning:

Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format
error, expected "<lower>"

This is a follow up to commit 4c9847b7 ("dt-bindings: Remove leading
0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The newly added OMAP35xx Torpedo does not have a WiFi option, so
this patch moves the WL1283 binding and pin muxing to the
logicpd-torpedo-37xx-devkit since it's only applicable on that SOM
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

With the common baseboard info moved into its own file and the
common torpedo already in its own file, we can very easily
create a new devkit specific for the OMAP35xx.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The Development kits consist of a SOM connected to a baseboard.  Moving most
of the devkit files to baseboard allow us to re-use much of the contents in
preparation for using it on the OMAP35xx varation of the same kit.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

With the common baseboard info moved into its own file and the common SOM-LV
already in its own file, we can very easily create a new devkit specific
for the OMAP35xx.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The Development kits consist of a SOM connected to a baseboard.  Moving most
of the devkit files to baseboard allow us to re-use much of the contents in
preparation for using it on the OMAP35xx varation of the same kit.
Signed-off-by: Adam Ford <aford173@gmail.com>
[tony@atomide.com: updated to apply on recent gpmc range fixes]
Signed-off-by: Tony Lindgren <tony@atomide.com>

The audio DMA request for hdmi is crossbar 76 and we use sDMA
to handle the data transfer.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The metastability workaround causes Erratic errors [1]
on the HighSpeed USB PHY which can cause upto 2 seconds
delay in enumerating to a USB host while in Gadget mode.

Disable the Run/Stop metastability workaround to avoid this
ill effect. We are aware that this opens up the opportunity
for Run/Stop metastability, however this issue has never been
observed in TI releases so we think that Run/Stop metastability
is a lesser evil than the PHY Erratic errors. So disable it.

[1] USB controller trace during gadget enumeration
    irq/90-dwc3-969   [000] d...    52.323145: dwc3_event: event
    (00000901): Erratic Error [U0]
    irq/90-dwc3-969   [000] d...    52.560646: dwc3_event: event
    (00000901): Erratic Error [U0]
    irq/90-dwc3-969   [000] d...    52.798144: dwc3_event: event
    (00000901): Erratic Error [U0]
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@linux/intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Since U-Boot passes this information to the kernel, let's remove
the partition information from the device tree for
logicpd-torpedo-37xx-devkit and logicpd-som-lv-37xx-devkit
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Set powerhold property for tps65917
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The correct DT property for specifying a GPIO used for reset
is "reset-gpios", fix this here.

Fixes: 14e3e295 ("ARM: dts: omap3-n900: Add TLV320AIC3X support")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The correct DT property for specifying a GPIO used for reset
is "reset-gpios", fix this here.

Fixes: 4341881d ("ARM: dts: Add devicetree for Gumstix Pepper board")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>