The LP1 suspending mode on Tegra means CPU rail off, devices and PLLs are
clock gated and SDRAM in self-refresh mode. That means the low level LP1
suspending and resuming code couldn't be run on DRAM and the CPU must
switch to the always on clock domain (a.k.a. CLK_M 12MHz oscillator). And
the system clock (SCLK) would be switched to CLK_S, a 32KHz oscillator.
The LP1 low level handling code need to be moved to IRAM area first. And
marking the LP1 mask for indicating the Tegra device is in LP1. The CPU
power timer needs to be re-calculated based on 32KHz that was originally
based on PCLK.

When resuming from LP1, the LP1 reset handler will resume PLLs and then
put DRAM to normal mode. Then jumping to the "tegra_resume" that will
restore full context before back to kernel. The "tegra_resume" handler
was expected to be found in PMC_SCRATCH41 register.

This is common LP1 procedures for Tegra, so we do these jobs mainly in
this patch:
* moving LP1 low level handling code to IRAM
* marking LP1 mask
* copying the physical address of "tegra_resume" to PMC_SCRATCH41
* re-calculate the CPU power timer based on 32KHz
Signed-off-by: Joseph Lo <josephl@nvidia.com>
[swarren, replaced IRAM_CODE macro with IO_ADDRESS(TEGRA_IRAM_CODE_AREA)]
Signed-off-by: Stephen Warren <swarren@nvidia.com>

When the system suspends to LP1, the CPU clock source is switched to
CLK_M (12MHz Oscillator) during suspend/resume flow. The CPU clock
source is controlled by the CCLKG_BURST_POLICY register, and hence this
register must be restored during LP1 resume.

Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

When suspending to LP1 mode, the SYSCLK will be clock gated. And different
board may have different polarity of the request of SYSCLK, this patch
configure the polarity from the DT for the board.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Add support to the Tegra CPU reset vector to detect whether the CPU is
resuming from LP1 suspend state. If it is, branch to the LP1-specific
resume code.

When Tegra enters the LP1 suspend state, the SDRAM controller is placed
into a self-refresh state. For this reason, we must place the LP1 resume
code into IRAM, so that it is accessible before SDRAM access has been
re-enabled.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Move all common select clauses from ARCH_TEGRA_*_SOC to ARCH_TEGRA to
eliminate duplication. The USB-related selects all should have been
common too, but were missing from Tegra114 previously. Move these to
ARCH_TEGRA too. The latter fixes a build break when only Tegra114
support was enabled, but not Tegra20 or Tegra30 support.
Signed-off-by: Stephen Warren <swarren@nvidia.com>

The Tegra114 can support suspend function now, removing the limitation.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Adding suspend/resume function for tegra_cpu_car_ops. We only save and
restore the setting of the clock of CoreSight. Other clocks still need
to be taken care by clock driver.

Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

The flow controller can help CPU to go into suspend mode (powered-down
state). When CPU goes into powered-down state, it needs some careful
settings before getting into and after leaving. The enter and exit
functions do that by configuring appropriate mode for flow controller.

For Tegra114, the setting is compatible with Tegra30.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Hooking tegra_tear_down_cpu for Tegra114 for supporting cluster power
down when CPU cluster suspneded in LP2.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

When the last CPU core in suspend, the CPU power rail can be turned off
by setting flags to flow controller. Then the flow controller will inform
PMC to turn off the CPU rail when the last CPU goes into suspend.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

When the CPU cluster power down, the vGIC is powered down too. The
flow controller needs to monitor the legacy interrupt controller to
wake up CPU. So setting up the appropriate wake up event in flow
controller.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

When there is a cluster power down cycle in suspend, we need to set up
the correct L2 RAM data RAM latency to make L2 cache work correctly. This
is only needed for cluster 0 and needs to be done in tegra_resume before
the cache is enabled.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Adding a flag for tegra_disable_clean_inv_dcache to flush cache as LoUIS
or ALL. After this patch, the v7_flush_dcache_louis is used for CPU hotplug
and CPU suspend in CPU power down (e.g. CPU idle power-down mode) case. And
the v7_flush_dcache_all is used for CPU cluster power down (e.g. suspend to
LP2 mode).
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

The v7_invalidate_l1 was used for the L1 cache that come out from reset
in a undefined state. This is no need for Cortex-A15. We do it for A9
only.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

This supports CPU core power down on each CPU when CPU idle. When CPU go
into this state, it saves it's context and needs a proper configuration
in flow controller to power gate the CPU when CPU runs into WFI
instruction. And the CPU also needs to set the IRQ as CPU power down idle
wake up event in flow controller.

Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

The flow controller would take care the power sequence when CPU idle in
powered-down mode. It powered gate the CPU when CPU runs into WFI
instruction. And wake up the CPU when event be triggered.

The sequence is below.
* setting wfi bitmap for the CPU as the halt event in the
  FLOW_CTRL_CPU_HALT_REG to monitor the CPU running into WFI,then power
  gate it
* setting IRQ and FIQ as wake up event to wake up CPU when event triggered
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

There is a difference between GICv1 and v2 when CPU in power management
mode (aka CPU power down on Tegra). For GICv1, IRQ/FIQ interrupt lines
going to CPU are same lines which are also used for wake-interrupt.
Therefore, we cannot disable the GIC CPU interface if we need to use same
interrupts for CPU wake purpose. This creates a race condition for CPU
power off entry. Also, in GICv1, disabling GICv1 CPU interface puts GICv1
into bypass mode such that incoming legacy IRQ/FIQ are sent to CPU, which
means disabling GIC CPU interface doesn't really disable IRQ/FIQ to CPU.

GICv2 provides a wake IRQ/FIQ (for wake-event purpose), which are not
disabled by GIC CPU interface. This is done by adding a bypass override
capability when the interrupts are disabled at the CPU interface. To
support this, there are four bits about IRQ/FIQ BypassDisable in CPU
interface Control Register. When the IRQ/FIQ not being driver by the
CPU interface, each interrupt output signal can be deasserted rather
than being driven by the legacy interrupt input.

So the wake-event can be used as wakeup signals to SoC (system power
controller).

To prevent race conditions and ensure proper interrupt routing on
Cortex-A15 CPUs when they are power-gated, add a CPU PM notifier
call-back to reprogram the GIC CPU interface on PM entry. The
GIC CPU interface will be reset back to its normal state by
the common GIC CPU PM exit callback when the CPU wakes up.

Based on the work by: Scott Williams <scwilliams@nvidia.com>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

This reverts commit 510bb595 "ARM: tegra: add cpu_disable for hotplug".

The Tegra114 support CPU0 hotplug function in HW physically, but it needs
other software to make it work normally after we add CPU idle power down
mode support. So remove them for now.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

The commit 93dc6887 (ARM: 7684/1: errata: Workaround for Cortex-A15
erratum 798181 (TLBI/DSB operations)) introduced a workaround for
Cortex-A15 erratum 798181. Enable it for Tegra114.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Pull slab update from Pekka Enberg:
 "Highlights:

  - Fix for boot-time problems on some architectures due to
    init_lock_keys() not respecting kmalloc_caches boundaries
    (Christoph Lameter)

  - CONFIG_SLUB_CPU_PARTIAL requested by RT folks (Joonsoo Kim)

  - Fix for excessive slab freelist draining (Wanpeng Li)

  - SLUB and SLOB cleanups and fixes (various people)"

I ended up editing the branch, and this avoids two commits at the end
that were immediately reverted, and I instead just applied the oneliner
fix in between myself.

* 'slab/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux
  slub: Check for page NULL before doing the node_match check
  mm/slab: Give s_next and s_stop slab-specific names
  slob: Check for NULL pointer before calling ctor()
  slub: Make cpu partial slab support configurable
  slab: add kmalloc() to kernel API documentation
  slab: fix init_lock_keys
  slob: use DIV_ROUND_UP where possible
  slub: do not put a slab to cpu partial list when cpu_partial is 0
  mm/slub: Use node_nr_slabs and node_nr_objs in get_slabinfo
  mm/slub: Drop unnecessary nr_partials
  mm/slab: Fix /proc/slabinfo unwriteable for slab
  mm/slab: Sharing s_next and s_stop between slab and slub
  mm/slab: Fix drain freelist excessively
  slob: Rework #ifdeffery in slab.h
  mm, slab: moved kmem_cache_alloc_node comment to correct place

In the -rt kernel (mrg), we hit the following dump:

BUG: unable to handle kernel NULL pointer dereference at           (null)
IP: [<ffffffff811573f1>] kmem_cache_alloc_node+0x51/0x180
PGD a2d39067 PUD b1641067 PMD 0
Oops: 0000 [#1] PREEMPT SMP
Modules linked in: sunrpc cpufreq_ondemand ipv6 tg3 joydev sg serio_raw pcspkr k8temp amd64_edac_mod edac_core i2c_piix4 e100 mii shpchp ext4 mbcache jbd2 sd_mod crc_t10dif sr_mod cdrom sata_svw ata_generic pata_acpi pata_serverworks radeon ttm drm_kms_helper drm hwmon i2c_algo_bit i2c_core dm_mirror dm_region_hash dm_log dm_mod
CPU 3
Pid: 20878, comm: hackbench Not tainted 3.6.11-rt25.14.el6rt.x86_64 #1 empty empty/Tyan Transport GT24-B3992
RIP: 0010:[<ffffffff811573f1>]  [<ffffffff811573f1>] kmem_cache_alloc_node+0x51/0x180
RSP: 0018:ffff8800a9b17d70  EFLAGS: 00010213
RAX: 0000000000000000 RBX: 0000000001200011 RCX: ffff8800a06d8000
RDX: 0000000004d92a03 RSI: 00000000000000d0 RDI: ffff88013b805500
RBP: ffff8800a9b17dc0 R08: ffff88023fd14d10 R09: ffffffff81041cbd
R10: 00007f4e3f06e9d0 R11: 0000000000000246 R12: ffff88013b805500
R13: ffff8801ff46af40 R14: 0000000000000001 R15: 0000000000000000
FS:  00007f4e3f06e700(0000) GS:ffff88023fd00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000000 CR3: 00000000a2d3a000 CR4: 00000000000007e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process hackbench (pid: 20878, threadinfo ffff8800a9b16000, task ffff8800a06d8000)
Stack:
 ffff8800a9b17da0 ffffffff81202e08 ffff8800a9b17de0 000000d001200011
 0000000001200011 0000000001200011 0000000000000000 0000000000000000
 00007f4e3f06e9d0 0000000000000000 ffff8800a9b17e60 ffffffff81041cbd
Call Trace:
 [<ffffffff81202e08>] ? current_has_perm+0x68/0x80
 [<ffffffff81041cbd>] copy_process+0xdd/0x15b0
 [<ffffffff810a2125>] ? rt_up_read+0x25/0x30
 [<ffffffff8104369a>] do_fork+0x5a/0x360
 [<ffffffff8107c66b>] ? migrate_enable+0xeb/0x220
 [<ffffffff8100b068>] sys_clone+0x28/0x30
 [<ffffffff81527423>] stub_clone+0x13/0x20
 [<ffffffff81527152>] ? system_call_fastpath+0x16/0x1b
Code: 89 fc 89 75 cc 41 89 d6 4d 8b 04 24 65 4c 03 04 25 48 ae 00 00 49 8b 50 08 4d 8b 28 49 8b 40 10 4d 85 ed 74 12 41 83 fe ff 74 27 <48> 8b 00 48 c1 e8 3a 41 39 c6 74 1b 8b 75 cc 4c 89 c9 44 89 f2
RIP  [<ffffffff811573f1>] kmem_cache_alloc_node+0x51/0x180
 RSP <ffff8800a9b17d70>
CR2: 0000000000000000
---[ end trace 0000000000000002 ]---

Now, this uses SLUB pretty much unmodified, but as it is the -rt kernel
with CONFIG_PREEMPT_RT set, spinlocks are mutexes, although they do
disable migration. But the SLUB code is relatively lockless, and the
spin_locks there are raw_spin_locks (not converted to mutexes), thus I
believe this bug can happen in mainline without -rt features. The -rt
patch is just good at triggering mainline bugs ;-)

Anyway, looking at where this crashed, it seems that the page variable
can be NULL when passed to the node_match() function (which does not
check if it is NULL). When this happens we get the above panic.

As page is only used in slab_alloc() to check if the node matches, if
it's NULL I'm assuming that we can say it doesn't and call the
__slab_alloc() code. Is this a correct assumption?
Acked-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull more vfs stuff from Al Viro:
 "O_TMPFILE ABI changes, Oleg's fput() series, misc cleanups, including
  making simple_lookup() usable for filesystems with non-NULL s_d_op,
  which allows us to get rid of quite a bit of ugliness"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  sunrpc: now we can just set ->s_d_op
  cgroup: we can use simple_lookup() now
  efivarfs: we can use simple_lookup() now
  make simple_lookup() usable for filesystems that set ->s_d_op
  configfs: don't open-code d_alloc_name()
  __rpc_lookup_create_exclusive: pass string instead of qstr
  rpc_create_*_dir: don't bother with qstr
  llist: llist_add() can use llist_add_batch()
  llist: fix/simplify llist_add() and llist_add_batch()
  fput: turn "list_head delayed_fput_list" into llist_head
  fs/file_table.c:fput(): add comment
  Safer ABI for O_TMPFILE

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

... and use d_hash_and_lookup() instead of open-coding it, for fsck sake...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

just pass the name
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull x86 platform driver updates from Matthew Garrett:
 "Nothing overly exciting here - a couple of new drivers that don't do a
  great deal, along with some miscellaneous fixes and a couple of small
  feature enablement patches"

* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86:
  x86 platform drivers: fix gpio leak
  toshiba_acpi: Add dependency on SERIO_I8042
  asus-nb-wmi: set wapf=4 for ASUSTeK COMPUTER INC. 1015E/U
  Add trivial driver to disable Intel Smart Connect
  Add support driver for Intel Rapid Start Technology
  hp-wmi: add supports for POST code error
  asus-wmi: control wlan-led only if wapf == 4
  drivers/platform/x86/intel_ips: Convert to module_pci_driver
  asus-nb-wmi: ignore ALS notification key code
  asus-wmi: append newline to messages
  x86: asus-laptop: fix invalid point access
  x86: msi-laptop: fix memleak
  amilo-rfkill: Add dependency on SERIO_I8042
  dell-laptop: fix error return code in dell_init()
  hp-wmi: Enable hotkeys on some systems

Pull second round of input updates from Dmitry Torokhov:
 "An update to Elantech driver to support hardware v7, fix to the new
  cyttsp4 driver to use proper addressing, ads7846 device tree support
  and nspire-keypad got a small cleanup."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: nspire-keypad - replace magic offset with define
  Input: elantech - fix for newer hardware versions (v7)
  Input: cyttsp4 - use 16bit address for I2C/SPI communication
  Input: ads7846 - add device tree bindings
  Input: ads7846 - make sure we do not change platform data

Pull networking fixes from David Miller:
 "Just a bunch of small fixes and tidy ups:

   1) Finish the "busy_poll" renames, from Eliezer Tamir.

   2) Fix RCU stalls in IFB driver, from Ding Tianhong.

   3) Linearize buffers properly in tun/macvtap zerocopy code.

   4) Don't crash on rmmod in vxlan, from Pravin B Shelar.

   5) Spinlock used before init in alx driver, from Maarten Lankhorst.

   6) A sparse warning fix in bnx2x broke TSO checksums, fix from Dmitry
      Kravkov.

   7) Dummy and ifb driver load failure paths can oops, fixes from Tan
      Xiaojun and Ding Tianhong.

   8) Correct MTU calculations in IP tunnels, from Alexander Duyck.

   9) Account all TCP retransmits in SNMP stats properly, from Yuchung
      Cheng.

  10) atl1e and via-rhine do not handle DMA mapping failures properly,
      from Neil Horman.

  11) Various equal-cost multipath route fixes in ipv6 from Hannes
      Frederic Sowa"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (36 commits)
  ipv6: only static routes qualify for equal cost multipathing
  via-rhine: fix dma mapping errors
  atl1e: fix dma mapping warnings
  tcp: account all retransmit failures
  usb/net/r815x: fix cast to restricted __le32
  usb/net/r8152: fix integer overflow in expression
  net: access page->private by using page_private
  net: strict_strtoul is obsolete, use kstrtoul instead
  drivers/net/ieee802154: don't use devm_pinctrl_get_select_default() in probe
  drivers/net/ethernet/cadence: don't use devm_pinctrl_get_select_default() in probe
  drivers/net/can/c_can: don't use devm_pinctrl_get_select_default() in probe
  net/usb: add relative mii functions for r815x
  net/tipc: use %*phC to dump small buffers in hex form
  qlcnic: Adding Maintainers.
  gre: Fix MTU sizing check for gretap tunnels
  pkt_sched: sch_qfq: remove forward declaration of qfq_update_agg_ts
  pkt_sched: sch_qfq: improve efficiency of make_eligible
  gso: Update tunnel segmentation to support Tx checksum offload
  inet: fix spacing in assignment
  ifb: fix oops when loading the ifb failed
  ...

Pull final round of SCSI updates from James Bottomley:
 "This is the remaining set of SCSI patches for the merge window.  It's
  mostly driver updates (scsi_debug, qla2xxx, storvsc, mp3sas).  There
  are also several bug fixes in fcoe, libfc, and megaraid_sas.  We also
  have a couple of core changes to try to make device destruction more
  deterministic"

* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (46 commits)
  [SCSI] scsi constants: command, sense key + additional sense strings
  fcoe: Reduce number of sparse warnings
  fcoe: Stop fc_rport_priv structure leak
  libfcoe: Fix meaningless log statement
  libfc: Differentiate echange timer cancellation debug statements
  libfc: Remove extra space in fc_exch_timer_cancel definition
  fcoe: fix the link error status block sparse warnings
  fcoe: Fix smatch warning in fcoe_fdmi_info function
  libfc: Reject PLOGI from nodes with incompatible role
  [SCSI] enable destruction of blocked devices which fail LUN scanning
  [SCSI] Fix race between starved list and device removal
  [SCSI] megaraid_sas: fix a bug for 64 bit arches
  [SCSI] scsi_debug: reduce duplication between prot_verify_read and prot_verify_write
  [SCSI] scsi_debug: simplify offset calculation for dif_storep
  [SCSI] scsi_debug: invalidate protection info for unmapped region
  [SCSI] scsi_debug: fix NULL pointer dereference with parameters dif=0 dix=1
  [SCSI] scsi_debug: fix incorrectly nested kmap_atomic()
  [SCSI] scsi_debug: fix invalid address passed to kunmap_atomic()
  [SCSI] mpt3sas: Bump driver version to v02.100.00.00
  [SCSI] mpt3sas: when async scanning is enabled then while scanning, devices are removed but their transport layer entries are not removed
  ...

Pull scheduler fix from Thomas Gleixner:
 "Fix a potential deadlock versus hrtimers"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched: Fix HRTICK

Pull irq updates from Thomas Gleixner:
 - core fix for missing round up in the generic irq chip implementation
 - new irq chip for MOXA SoCs
 - a few fixes and cleanups in the irqchip drivers

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip: Add support for MOXA ART SoCs
  genirq: generic chip: Use DIV_ROUND_UP to calculate numchips
  irqchip: nvic: Fix wrong num_ct argument for irq_alloc_domain_generic_chips()
  irqchip: sun4i: Staticize sun4i_irq_ack()
  irqchip: vt8500: Staticize local symbols

Pull timer updates from Thomas Gleixner:
 - watchdog fixes for full dynticks
 - improved debug output for full dynticks
 - remove an obsolete full dynticks check
 - two ARM SoC clocksource drivers for sharing across SoCs
 - tick broadcast fix for CPU hotplug

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tick: broadcast: Check broadcast mode on CPU hotplug
  clocksource: arm_global_timer: Add ARM global timer support
  clocksource: Add Marvell Orion SoC timer
  nohz: Remove obsolete check for full dynticks CPUs to be RCU nocbs
  watchdog: Boot-disable by default on full dynticks
  watchdog: Rename confusing state variable
  watchdog: Register / unregister watchdog kthreads on sysctl control
  nohz: Warn if the machine can not perform nohz_full

Pull perf fixes from Thomas Gleixner:
 - fix for do_div() abuse on x86
 - locking fix in perf core
 - a pile of (build) fixes and cleanups in perf tools

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
  perf/x86: Fix incorrect use of do_div() in NMI warning
  perf: Fix perf_lock_task_context() vs RCU
  perf: Remove WARN_ON_ONCE() check in __perf_event_enable() for valid scenario
  perf: Clone child context from parent context pmu
  perf script: Fix broken include in Context.xs
  perf tools: Fix -ldw/-lelf link test when static linking
  perf tools: Revert regression in configuration of Python support
  perf tools: Fix perf version generation
  perf stat: Fix per-socket output bug for uncore events
  perf symbols: Fix vdso list searching
  perf evsel: Fix missing increment in sample parsing
  perf tools: Update symbol_conf.nr_events when processing attribute events
  perf tools: Fix new_term() missing free on error path
  perf tools: Fix parse_events_terms() segfault on error path
  perf evsel: Fix count parameter to read call in event_format__new
  perf tools: fix a typo of a Power7 event name
  perf tools: Fix -x/--exclude-other option for report command
  perf evlist: Enhance perf_evlist__start_workload()
  perf record: Remove -f/--force option
  perf record: Remove -A/--append option
  ...

Pull core locking updates from Thomas Gleixner:
 "Header cleanup as requested by Linus"

(This is the "don't include support for ww_mutex in a header file that
everybody wants, when almost nobody wants the ww part" change)

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  mutex: Move ww_mutex definitions to ww_mutex.h

Pull ARM SoC fixes from Olof Johansson:
 "This is our first set of fixes from arm-soc for 3.11.
   - A handful of build and warning fixes from Arnd
   - A collection of OMAP fixes
   - defconfig updates to make the default configs more useful for real
     use (and testing) out of the box on hardware

  And a couple of other small fixes.  Some of these have been recently
  applied but it's normally how we deal with fixes, with less bake time
  in -next needed"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits)
  arm: multi_v7_defconfig: Tweaks for omap and sunxi
  arm: multi_v7_defconfig: add i.MX options and NFS root
  ARM: omap2: add select of TI_PRIV_EDMA
  ARM: exynos: select PM_GENERIC_DOMAINS only when used
  ARM: ixp4xx: avoid circular header dependency
  ARM: OMAP: omap_common_late_init may be unused
  ARM: sti: move DEBUG_STI_UART into alphabetical order
  ARM: OMAP: build mach-omap code only if needed
  ARM: zynq: use DT_MACHINE_START
  ARM: omap5: omap5 has SCU and TWD
  ARM: OMAP2+: omap2plus_defconfig: Enable appended DTB support
  ARM: OMAP2+: Enable TI_EDMA in omap2plus_defconfig
  ARM: OMAP2+: omap2plus_defconfig: enable DRA752 thermal support by default
  ARM: OMAP2+: omap2plus_defconfig: enable TI bandgap driver
  ARM: OMAP2+: devices: remove duplicated include from devices.c
  ARM: OMAP3: igep0020: Set DSS pins in correct mux mode.
  ARM: OMAP2+: N900: enable N900-specific drivers even if device tree is enabled
  ARM: OMAP2+: Cocci spatch "ptr_ret.spatch"
  ARM: OMAP2+: Remove obsolete Makefile line
  ARM: OMAP5: Enable Cortex A15 errata 798181
  ...