Add missing .owner field in regulator_desc, which is used for refcounting.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Currently rdev is dereferenced when assigning desc before rdev is null
checked, this is leading to static analysis warnings.  However, rdev
can never be null, so the null check is redundant and can be removed.

Detected by CoverityScan, CID#1476031 ("Dereference before null check")

Fixes: 77e3e3b1 ("regulator: axp20x: add software based soft_start for AXP209 LDO3")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Selecting the minimal value is only true for voltage regulators.
For current regulators the maximum in the given range should be
selected instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Selecting the minimal value is only true for voltage regulators.
For current regulators the maximum in the given range should be
selected instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Change buck1 voltage range to be conform with the data-sheet.
Signed-off-by: pascal paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add support for active discharge for USB power switches.
Signed-off-by: pascal paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add support for active discharge for USB power switches.
Signed-off-by: pascal paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Regulator high pull down are enabled by default so remove support in the
driver.
Signed-off-by: pascal paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Regulator high pull down are enabled by default so remove support in the
driver.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Stop using a regulator_init callback. This leads to a more simple regulator
registration code. This also permits to spuress struct stpmic1_regulator.
Also rename stpmic1_regulators_matches to stpmic1_matches.
Signed-off-by: pascal paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The interrupt parent description is not needed as the parent is a parent
node with 'interrupt-controller' property.
Signed-off-by: pascal paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Get the regulator mode definition from the bindings header.
Signed-off-by: pascal paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

commit e5e21f70 ("regulator: core: Take lock before applying system
load") took the regulator lock before calling drms_uA_update() in order
to silence a lockdep warning during regulator_register().

However, we are not supposed to need locks at this point as the regulator
is in the process of being registered, so there should be no possibility
of concurrent access.

Instead, remove the unnecessary locking and simply drop the lockdep
annotation, since it is no longer valid.

Fixes: e5e21f70 ("regulator: core: Take lock before applying system load")
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

At the context with *rdev available, regulator core provides
rdev_get_id()/rdev_get_regmap() APIs to get regulator id and *regmap.
So no need to store them in struct stpmic1_regulator.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

There is no vsel_reg/vsel_mask settings for PV88060_ID_SWx, so don't use
pv88060_ldo_ops for PV88060_SW. The PV88060_ID_SWx is fixed voltage,
set .fixed_uV instead of .min_uV then regulator core will automatically
support get_voltage and list_voltage.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This is a remnant of commit 70a7fb80 ("regulator: core: Fix nested
locking of supplies").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This fixes another set of errors from the refactoring of literals
to mask preproccesor definitions.

Found by debugging a broken voltage setup on Orange Pi One Plus.

Fixes: db4a555f ("regulator: axp20x: use defines for masks")
Signed-off-by: Ondrej Jirman <megous@megous.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Take the regulator lock before applying system load.

Fixes the following lockdep splat:

[    5.583581] WARNING: CPU: 1 PID: 16 at drivers/regulator/core.c:925 drms_uA_update+0x114/0x360
[    5.588467] Modules linked in:
[    5.596833] CPU: 1 PID: 16 Comm: kworker/1:0 Not tainted 5.0.0-rc6-next-20190213-00002-g0fce66ab480f #18
[    5.599933] Hardware name: Qualcomm Technologies, Inc. APQ 8016 SBC (DT)
[    5.609544] Workqueue: events qcom_channel_state_worker
[    5.616209] pstate: 60000005 (nZCv daif -PAN -UAO)
[    5.621152] pc : drms_uA_update+0x114/0x360
[    5.626006] lr : drms_uA_update+0x110/0x360
[    5.630084] sp : ffff0000124b3490
[    5.634242] x29: ffff0000124b3490 x28: ffff800005326e00
[    5.637735] x27: ffff0000124b35f8 x26: 000000000032bc48
[    5.643117] x25: ffff800004c7e800 x24: ffff800004c6d500
[    5.648411] x23: ffff800004c38a80 x22: 00000000000000d1
[    5.653706] x21: 00000000001ab3f0 x20: ffff800004c7e800
[    5.659001] x19: ffff0000114c3000 x18: ffffffffffffffff
[    5.664297] x17: 0000000000000000 x16: 0000000000000000
[    5.669592] x15: ffff0000114c3808 x14: 0720072007200720
[    5.674888] x13: 00000000199c9b28 x12: ffff80002bcccc40
[    5.680183] x11: ffff000012286000 x10: ffff0000114c3808
[    5.685477] x9 : 0720072007200720 x8 : ffff000010e9e808
[    5.690772] x7 : ffff0000106da568 x6 : 0000000000000000
[    5.696067] x5 : 0000000000000000 x4 : 0000000000000000
[    5.701362] x3 : 0000000000000004 x2 : 0000000000000000
[    5.706658] x1 : 0000000000000000 x0 : 0000000000000000
[    5.711952] Call trace:
[    5.717223]  drms_uA_update+0x114/0x360
[    5.719405]  regulator_register+0xb30/0x1140
[    5.723230]  devm_regulator_register+0x4c/0xa8
[    5.727745]  rpm_reg_probe+0xfc/0x1b0
[    5.731992]  platform_drv_probe+0x50/0xa0
[    5.735727]  really_probe+0x20c/0x2b8
[    5.739718]  driver_probe_device+0x58/0x100
[    5.743368]  __device_attach_driver+0x90/0xd0
[    5.747363]  bus_for_each_drv+0x64/0xc8
[    5.751870]  __device_attach+0xd8/0x138
[    5.755516]  device_initial_probe+0x10/0x18
[    5.759341]  bus_probe_device+0x98/0xa0
[    5.763502]  device_add+0x3d0/0x640
[    5.767319]  of_device_add+0x48/0x58
[    5.770793]  of_platform_device_create_pdata+0xb0/0x128
[    5.774629]  of_platform_bus_create+0x174/0x370
[    5.779569]  of_platform_populate+0x78/0xe0
[    5.784082]  qcom_smd_rpm_probe+0x80/0xa0
[    5.788245]  rpmsg_dev_probe+0x114/0x1a0
[    5.792411]  really_probe+0x20c/0x2b8
[    5.796401]  driver_probe_device+0x58/0x100
[    5.799964]  __device_attach_driver+0x90/0xd0
[    5.803960]  bus_for_each_drv+0x64/0xc8
[    5.808468]  __device_attach+0xd8/0x138
[    5.812115]  device_initial_probe+0x10/0x18
[    5.815936]  bus_probe_device+0x98/0xa0
[    5.820099]  device_add+0x3d0/0x640
[    5.823916]  device_register+0x1c/0x28
[    5.827391]  rpmsg_register_device+0x4c/0x90
[    5.831216]  qcom_channel_state_worker+0x170/0x298
[    5.835651]  process_one_work+0x294/0x6e8
[    5.840241]  worker_thread+0x40/0x450
[    5.844318]  kthread+0x11c/0x120
[    5.847961]  ret_from_fork+0x10/0x18
[    5.851260] irq event stamp: 9090
[    5.854820] hardirqs last  enabled at (9089): [<ffff000010160798>] console_unlock+0x3e0/0x5b0
[    5.858086] hardirqs last disabled at (9090): [<ffff0000100817cc>] do_debug_exception+0x104/0x140
[    5.866596] softirqs last  enabled at (9086): [<ffff000010082024>] __do_softirq+0x474/0x574
[    5.875446] softirqs last disabled at (9079): [<ffff0000100f2254>] irq_exit+0x13c/0x148
[    5.883598] ---[ end trace 6984ef7f081afa21 ]---

Fixes: fa94e48e ("regulator: core: Apply system load even if no consumer loads")
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

This driver is for LTC3676 rather than LTC1376.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Use case range for continuous range to make the code shorter.
The .readable_reg and .writable_reg implementation are exactly the same,
so use a common ltc3676_readable_writeable_reg function instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

read ROHM BD71837 / BD71847 specific device tree bindings for
controlling the PMIC shutdown/reset states and voltages for
different HW states. The PMIC was designed to be used with NXP
i.MX8 SoC and it supports SNVS low power state which seems to
be typical for NXP i.MX SoCs. However, when SNVS is used we must
not allow SW to control enabling/disabling those regulators which
are crucial for system to boot as there is a HW limitation which
causes SW controlled regulators to be kept shut down after SNVS
reset.

Allow setting the SNVS to be used as reset target state and allow
marking those regulators which are critical for boot.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Tested-by: Angus Ainslie <angus@akkea.ca>
Reviewed-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add regulator_desc_list_voltage_linear_range which can be used
by drivers for getting the voltages before regulator is registered.
This may be useful for drivers which need to fetch the voltage
selectors at device-tree parsing callback.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Mark Brown <broonie@kernel.org>
Tested-by: Angus Ainslie <angus@akkea.ca>
Reviewed-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add ROHM BD71837 / BD71847 specific device tree bindings for
controlling the PMIC shutdown/reset states and voltages for
different HW states. The PMIC was designed to be used with NXP
i.MX8 SoC and it supports SNVS low power state which seems to
be typical for NXP i.MX SoCs. However, when SNVS is used we must
not allow SW to control enabling/disabling those regulators which
are crucial for system to boot as there is a HW limitation which
causes SW controlled regulators to be kept shut down after SNVS
reset.

Allow setting the SNVS to be used as reset target state and allow
marking those regulators which are critical for boot.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Tested-by: Angus Ainslie <angus@akkea.ca>
Reviewed-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Mark Brown <broonie@kernel.org>

As a result of exporting the bd70528 specific locking functions
we no longer need struct bd70528. Remove references to
struct bd70528 from bd70528 regulator.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The step values for some of the LDOs appears to be incorrect, resulting
in incorrect voltages (or at least, ones which are different from the
Samsung 3.4 vendor kernel).
Signed-off-by: Stuart Menefy <stuart.menefy@mathembedded.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

There are several lines in an if statement that are not indented
correctly. Fix these by removing the tabs.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

linear range is suitable for this driver, let's convert it to linear range.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

LDO35 uses 25 mV step, not 50 mV.  Bucks 7 and 8 use 12.5 mV step
instead of 6.25 mV.  Wrong step caused over-voltage (LDO35) or
under-voltage (buck7 and 8) if regulators were used (e.g. on Exynos5420
Arndale Octa board).

Cc: <stable@vger.kernel.org>
Fixes: cb74685e ("regulator: s2mps11: Add samsung s2mps11 regulator driver")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

gpiod_get_index_optional can return ERR_PTR, add IS_ERR checking for it.
While at it, also remove a redundant NULL test for gpiod in error path.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Fixed regulators do not have associated bus addresses and are typically
placed directly under the root node where their names must still be
unique despite not having a unit address.

Fix the malformed example node which had a unit address but no "reg"
property by dropping the unit address.

Also, try to make the example more useful by using the recommended
generic node name "regulator", but with a suffix reflecting the
regulator name in order to make it unique.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Device links are refcounted, device_link_remove() has to be called as
many times as device_link_add().
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

With current n_voltages setting, regulator_list_voltage will return
-EINVAL when selector >=57. The highest selector is 0x41, so the
n_voltages should be 0x41+1, i.e. 66.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Now that we changed all providers to pass descriptors into the core
for enable GPIOs instead of a global GPIO number, delete the support
for passing GPIO numbers in, and we get a cleanup and size reduction
in the core, and from a GPIO point of view we use the modern, cleaner
interface.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Use devm_* managed device resources and create a local
struct device *dev variable to simplify the code inside
probe().
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

This pushes the handling of inversion semantics and open drain
settings to the GPIO descriptor and gpiolib. All affected board
files are also augmented.

This is especially nice since we don't have to have any
confusing flags passed around to the left and right littering
the fixed and GPIO regulator drivers and the regulator core.
It is all just very straight-forward: the core asks the GPIO
line to be asserted or deasserted and gpiolib deals with the
rest depending on how the platform is configured: if the line
is active low, it deals with that, if the line is open drain,
it deals with that too.

Cc: Alexander Shiyan <shc_work@mail.ru> # i.MX boards user
Cc: Haojian Zhuang <haojian.zhuang@gmail.com> # MMP2 maintainer
Cc: Aaro Koskinen <aaro.koskinen@iki.fi> # OMAP1 maintainer
Cc: Tony Lindgren <tony@atomide.com> # OMAP1,2,3 maintainer
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> # EM-X270 maintainer
Cc: Robert Jarzmik <robert.jarzmik@free.fr> # EZX maintainer
Cc: Philipp Zabel <philipp.zabel@gmail.com> # Magician maintainer
Cc: Petr Cvek <petr.cvek@tul.cz> # Magician
Cc: Robert Jarzmik <robert.jarzmik@free.fr> # PXA
Cc: Paul Parsons <lost.distance@yahoo.com> # hx4700
Cc: Daniel Mack <zonque@gmail.com> # Raumfeld maintainer
Cc: Marc Zyngier <marc.zyngier@arm.com> # Zeus maintainer
Cc: Geert Uytterhoeven <geert+renesas@glider.be> # SuperH pinctrl/GPIO maintainer
Cc: Russell King <rmk+kernel@armlinux.org.uk> # SA1100
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> #OMAP1 Amstrad Delta
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

This converts the GPIO regulator driver to use decriptors only.

We have to let go of the array gpio handling: the fetched descriptors
are handled individually anyway, and the array retrieveal function
does not make it possible to retrieve each GPIO descriptor with
unique flags. Instead get them one by one.

We request the "enable" GPIO separately as before, and make sure
that this line is requested as nonexclusive since enable lines can
be shared and the regulator core expects this.

Most users of the GPIO regulator are using device tree.

There are two boards in the kernel using the gpio regulator from a
non-devicetree path: PXA hx4700 and magician. Make sure to switch
these over to use descriptors as well.

Cc: Philipp Zabel <p.zabel@pengutronix.de> # Magician
Cc: Petr Cvek <petr.cvek@tul.cz> # Magician
Cc: Robert Jarzmik <robert.jarzmik@free.fr> # PXA
Cc: Paul Parsons <lost.distance@yahoo.com> # hx4700
Cc: Kevin Hilman <khilman@baylibre.com> # Meson
Cc: Neil Armstrong <narmstrong@baylibre.com> # Meson
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

It looks like linear range is suitable to describe the voltage table
for rk805 buck1/2:

selector 0 ~ 59: 0.7125V with uV_step = 12500
selector 60 ~ 62: 1.8V with uV_step = 200000
selector 63: 2.3V

With this change, then rk805 buck1/2 can reuse rk808_reg_ops_ranges.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Mark Brown <broonie@kernel.org>

A comma has been accidentally used where a semi-colon was clearly
intended, correct this typo.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>