Since commit 32b8a8e5 "sit: add IPv4 over IPv4 support",
tunnel->parms.iph.protocol is 0 when both 4in4 and 6in4 are setup, but
xfrm_lookup() is called only when proto is != 0, thus we need to pass the real
value.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Steffen Klassert says:

====================
Just one patch this time.

1) Drop packets when the matching SA is in larval state and add a
   statistic counter for that. From Fan Du.

Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

As reported by "kbuild test robot" there were some errors and warnings
on attempt to build kernel with "make ARCH=powerpc allmodconfig".

And this patch addresses both errors and warnings.
Below is a list of introduced changes:
1. Fix compile-time errors (misspellings in "dma_unmap_single") on PPC.
2. Use DMA address instead of "skb->data" as a pointer to data buffer.
This fixed warnings on pointer to int conversion on 64-bit systems.
3. Re-implemented initial allocation of Rx buffers in "arc_emac_open" in
the same way they're re-allocated during operation (receiving packets).
So once again DMA address could be used instead of "skb->data".
4. Explicitly use EMAC_BUFFER_SIZE for Rx buffers allocation.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

Cc: netdev@vger.kernel.org
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: Joe Perches <joe@perches.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-kernel@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Florian Fainelli <florian@openwrt.org>
Cc: David Laight <david.laight@aculab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, we fail only when all of the ips in arp_ip_target are gone.
However, in some situations we might need to fail if even one host from
arp_ip_target becomes unavailable.

All situations, obviously, rely on the idea that we need *completely*
functional network, with all interfaces/addresses working correctly.

One real world example might be:
vlans on top on bond (hybrid port). If bond and vlans have ips assigned
and we have their peers monitored via arp_ip_target - in case of switch
misconfiguration (trunk/access port), slave driver malfunction or
tagged/untagged traffic dropped on the way - we will be able to switch
to another slave.

Though any other configuration needs that if we need to have access to all
arp_ip_targets.

This patch adds this possibility by adding a new parameter -
arp_all_targets (both as a module parameter and as a sysfs knob). It can be
set to:

	0 or any (the default) - which works exactly as it's working now -
	the slave is up if any of the arp_ip_targets are up.

	1 or all - the slave is up if all of the arp_ip_targets are up.

This parameter can be changed on the fly (via sysfs), and requires the mode
to be active-backup and arp_validate to be enabled (it obeys the
arp_validate config on which slaves to validate).

Internally it's done through:

1) Add target_last_arp_rx[BOND_MAX_ARP_TARGETS] array to slave struct. It's
   an array of jiffies, meaning that slave->target_last_arp_rx[i] is the
   last time we've received arp from bond->params.arp_targets[i] on this
   slave.

2) If we successfully validate an arp from bond->params.arp_targets[i] in
   bond_validate_arp() - update the slave->target_last_arp_rx[i] with the
   current jiffies value.

3) When getting slave's last_rx via slave_last_rx(), we return the oldest
   time when we've received an arp from any address in
   bond->params.arp_targets[].

If the value of arp_all_targets == 0 - we still work the same way as
before.

Also, update the documentation to reflect the new parameter.

v3->v4:
Kill the forgotten rtnl_unlock(), rephrase the documentation part to be
more clear, don't fail setting arp_all_targets if arp_validate is not set -
it has no effect anyway but can be easier to set up. Also, print a warning
if the last arp_ip_target is removed while the arp_interval is on, but not
the arp_validate.

v2->v3:
Use _bh spinlock, remove useless rtnl_lock() and use jiffies for new
arp_ip_target last arp, instead of slave_last_rx(). On bond_enslave(),
use the same initialization value for target_last_arp_rx[] as is used
for the default last_arp_rx, to avoid useless interface flaps.

Also, instead of failing to remove the last arp_ip_target just print a
warning - otherwise it might break existing scripts.

v1->v2:
Correctly handle adding/removing hosts in arp_ip_target - we need to
shift/initialize all slave's target_last_arp_rx. Also, don't fail module
loading on arp_all_targets misconfiguration, just disable it, and some
minor style fixes.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add some details to bonding documentation on how backup slave arp
validation works.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, if we receive any arp packet on a backup slave in active-backup
mode and arp_validate enabled, we suppose that it's an arp request, swap
source/target ip and try to validate it. This optimization gives us
virtually no downtime in the most common situation (active and backup
slaves are in the same broadcast domain and the active slave failed).

However, if we can't reach the arp_ip_target(s), we end up in an endless
loop of reselecting slaves, because we receive our arp requests, sent by
the active slave, and think that backup slaves are up, thus selecting them
as active and, again, sending arp requests, which fool our backup slaves.

Fix this by not validating the swapped arp packets if the current active
slave didn't receive any arp reply after it was selected as active. This
way we will only accept arp requests if we know that the current active
slave can actually reach arp_ip_target.

v3->v4:
Obey 80 lines and make checkpatch.pl happy, per Sergei's suggestion.

v1->v3:
No change.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, we validate all the incoming arps if arp_validate not 0.
However, we don't have to validate backup slaves if arp_validate == active
and vice versa, so return early in bond_arp_rcv() in these cases.

It works correctly now because we verify arp_validate in slave_last_rx(),
however we're just doing useless work in bond_arp_rcv().
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Print a warning and skip them.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add function bond_get_targets_ip(targets, ip) which searches through
targets array of ips (arp_targets) and returns the position of first
match. If ip == 0, returns the first free slot. On failure to find the
ip or free slot, return -1.

Use it to verify if the arp we've received is valid and in sysfs.

v1->v2:
Fix "[2/6] bonding: add helper function bond_get_targets_ip(targets, ip)",
per Nikolay's advice, to verify if source ip != 0.0.0.0, otherwise we might
update 'null' arp_ip_targets' last_rx. Also, address style.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

guard the davinci_mdio_of_mtable table and davinci_mdio_probe_dt()
with CONFIG_OF.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch cleans up the OF parser code, removes unnecessary checks
on of_property_read_*() and guards davinci_emac_of_match table with
CONFIG_OF.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use devm_ioremap_resource instead of devm_request_mem_region()/devm_ioremap()
and devm_request_irq() instead of request_irq().

This ensures more consistent error values and simplifies error paths.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cc: Patrick McHardy <kaber@trash.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When macvtap forwards skb to its tap, it needs to check
if GSO needs to be performed.  This is sometimes necessary
when the HW device performed GRO, but the guest reading
from the tap does not support it (ex: Windows 7).
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the user issues TUNSETOFFLOAD ioctl, macvtap does not do
anything other then to verify arguments.  This patch adds
functionality to allow users to actually control offload features.
NETIF_F_GSO and NETIF_F_GRO are always on, but the rest of the
features can be controlled.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently macvtap uses rcu_bh functions in its
user facing fuction macvtap_get_user() and macvtap_put_user().
However, its packet handlers use normal rcu as the rcu_read_lock()
is taken in netif_receive_skb().  We can safely discontinue
the usage or rcu with bh disabled.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Macvtap uses a private lock to protect the relationship between
macvtap_queue and macvlan_dev.  The private lock is not needed
since the relationship is managed by user via open(), release(),
and dellink() calls.  dellink() already happens under rtnl, so
we can safely convert open() and release(), and use it in ioctl()
as well.

Suggested by Eric Dumazet.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

select/poll busy-poll support.

Split sysctl value into two separate ones, one for read and one for poll.
updated Documentation/sysctl/net.txt

Add a new poll flag POLL_LL. When this flag is set, sock_poll will call
sk_poll_ll if possible. sock_poll sets this flag in its return value
to indicate to select/poll when a socket that can busy poll is found.

When poll/select have nothing to report, call the low-level
sock_poll again until we are out of time or we find something.

Once the system call finds something, it stops setting POLL_LL, so it can
return the result to the user ASAP.
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Driver for non-standard on-chip ethernet device ARC EMAC 10/100,
instantiated in some legacy ARC (Synopsys) FPGA Boards such as
ARCAngel4/ML50x.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: Joe Perches <joe@perches.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-kernel@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Florian Fainelli <florian@openwrt.org>
Cc: David Laight <david.laight@aculab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

No need to have an extra ret variable when we directly can return
the value of sctp_get_port_local().
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rather instead of having the endpoint clean the garbage from the
socket, use a sk_destruct handler sctp_destruct_sock(), that does
the job for that when there are no more references on the socket.
At least do this for our crypto transform through crypto_free_hash()
that is allocated when in listening state.

Also, perform sctp_put_port() only when sk is valid. At a later
point in time we can still determine if there's an option of
placing this into sk_prot->unhash() or sctp_endpoint_free() without
any races. For now, leave it in sctp_endpoint_destroy() though.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A trailing newline has been forgotten to add into the WARN().
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, SCTP code defines its own timeval functions (since timeval
is rarely used inside the kernel by others), namely tv_lt() and
TIMEVAL_ADD() macros, that operate on SCTP cookie expiration.

We might as well remove all those, and operate directly on ktime
structures for a couple of reasons: ktime is available on all archs;
complexity of ktime calculations depending on the arch is less than
(reduces to a simple arithmetic operations on archs with
BITS_PER_LONG == 64 or CONFIG_KTIME_SCALAR) or equal to timeval
functions (other archs); code becomes more readable; macros can be
thrown out.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add two ktime helper functions that i) convert a given msec value to
a ktime structure and ii) that adds a msec value to a ktime structure.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We do neither ship a test_frame.h, nor will this be compatible with
the 2.5 out-of-tree lksctp kernel test suite anyway. So remove this
artefact.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Should not allow negative num_vfs
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.com>
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Warning prints when there are command timeout to help debugging future
failures.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is not safe to use sscanf.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.com>
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since this variable is now part of a structure and not allocated dynamically,
this test is irrelevant now.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Print a warning when a TX timeout is detected
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The RX rings were cleaned while there was still possible RX traffic completion
handling.
Change the sequance of events so that the port is closed and the QPs are being
stopped before RX cleanup.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The port vlan table size is 126 (used for IBoE) so after 126 we will
not have space and the user need to see it only in debug print and not
error.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To avoid a race between the open function and everything that happens after
register_netdev() move it to be the last operation called.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are no counters allocated to the eth device when the port is down, so
this query is meaningless at that time.

It also leads to querying incorrect counters (since the counter_index is not
valid when the device port is down).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Wrong condition was used when calling iounmap.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the tokenized ip address is re-set on an interface we depend on the
arrival of a new router advertisment to call addrconf_verify to clean
up the old address (which valid_lft is now set to 0). Old addresses can
linger around for a longer time if e.g. the source of router advertisments
vanishes.

So, call addrconf_verify immediately after setting the new tokenized
address to get rid of the old tokenized addresses.

Cc: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The reason behind this change is that as soon as we delete
the last ipv6 address of an interface we also lose the
/proc/sys/net/ipv6/conf/<interface> directory. This seems to be a
usability problem for me.

I don't see any reason why we should shutdown ipv6 on that interface in
such cases.

Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch splits the timers for duplicate address detection and router
solicitations apart. The router solicitations timer goes into inet6_dev
and the dad timer stays in inet6_ifaddr.

The reason behind this patch is to reduce the number of unneeded router
solicitations send out by the host if additional link-local addresses
are created. Currently we send out RS for every link-local address on
an interface.

If the RS timer fires we pick a source address with ipv6_get_lladdr. This
change could hurt people adding additional link-local addresses and
specifying these addresses in the radvd clients section because we
no longer guarantee that we use every ll address as source address in
router solicitations.

Cc: Flavio Leitner <fleitner@redhat.com>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: David Stevens <dlstevens@us.ibm.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Reviewed-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Eric Dumazet <edumazet@google.com>

mlx4 exclusively uses order-2 allocations in RX path, which are
likely to fail under memory pressure.

We therefore drop frames more than needed.

This patch tries order-3, order-2, order-1 and finally order-0
allocations to keep good performance, yet allow allocations if/when
memory gets fragmented.

By using larger pages, and avoiding unnecessary get_page()/put_page()
on compound pages, this patch improves performance as well, lowering
false sharing on struct page.

Also use GFP_KERNEL allocations in initialization path, as allocating 12
MB (390 order-3 pages) can easily fail with GFP_ATOMIC.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Amir Vadai <amirv@mellanox.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ben Hutchings says:

====================
1. Make EEH recovery work when using legacy interrupts, from Alexandre
   Rames.

2. Enable accelerated RFS for VLAN-tagged flows, from Andy Lutomirski.

3. Improve performance for non-TCP (and particularly UDP) traffic, which
   regressed in 3.10 when we switched to always allocating paged RX
   buffers.  Partly by Jon Cooper.

4. Some minor bug fixes to IOMMU detection, timestamping capabilities,
   and IRQ cleanup on the probe failure path.

I've dropped the RX skb cache, which improved some benchmarks but
perhaps needs some reworking to be more generally useful.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>