- 23 Feb, 2015 25 commits
-
-
Wolfram Sang authored
Documentation says the last register is at 0x184 (CAxCPUCMCR), so use proper length. Current APMU code accesses CAxCPUnCR which is currently outside of the remapped area. Signed-off-by:
Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by:
Simon Horman <horms+renesas@verge.net.au>
-
Wolfram Sang authored
Documentation says the last register is at 0x184 (CAxCPUCMCR), so use proper length. Current APMU code accesses CAxCPUnCR which is currently outside of the remapped area. Signed-off-by:
-
Laurent Pinchart authored
Add DT nodes for the ADV7511 HDMI encoder and its HDMI output connector and configure the DISP pin group that drives the HDMI transmitter DE pin. Signed-off-by:
Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by:
-
Simon Horman authored
There appears to have been some inconsistency and confusion here as on the r8a7790 these clocks are referred to as SD(HI)1 and SD(HI)2 while on the r8a7791 and r8a7794 they are referred to as SD(HI)2 and SD(HI)3. Fixes: 59e79895 ("ARM: shmobile: r8a7791: Add clocks") Reported-by:
Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be>
-
Simon Horman authored
* Correct base address of SD3 div6 clk. * Update div6 clock node labels There appears to have been some inconsistency and confusion here as on the r8a7790 these clocks are referred to as SD(HI)1 and SD(HI)2 while on the r8a7791 and r8a7794 they are referred to as SD(HI)2 and SD(HI)3. This has no run-time affect as the clock nodes are not currently used. Fixes: 8e181633 ("ARM: shmobile: r8a7794: Add SDHI clocks to device tree") Reported-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reported-by:
-
Laurent Pinchart authored
Enable the ethernet controller for the Alt board. Pin muxing entries are currently left out as r8a7794 pin control support isn't available yet. We thus rely on the boot loader to configure ethernet pins for now. Signed-off-by:
-
Laurent Pinchart authored
Add a DT node for the on-SoC ethernet controller device. Signed-off-by:
-
Laurent Pinchart authored
Add the six IPMMU instances found in the r8a7794 to DT with a disabled status. Signed-off-by:
-
Laurent Pinchart authored
Add the seven IPMMU instances found in the r8a7791 to DT with a disabled status. Signed-off-by:
-
Laurent Pinchart authored
Add the six IPMMU instances found in the r8a7790 to DT with a disabled status. Signed-off-by:
-
Laurent Pinchart authored
Instantiate the two system DMA controllers in the r8a7794 device tree. Signed-off-by:
-
Geert Uytterhoeven authored
Traditionally, the first 16 MiB of RAM was reserved for the RT processor. However, this is incompatible with CONFIG_AUTO_ZRELADDR=y, which requires that the start address of physical memory is a multiple of 128 MiB. As CONFIG_AUTO_ZRELADDR=y is enabled for multi-platform kernels, declare RAM to start at 0x40000000. While at it, reclaim the last 8 MiB of RAM, too, so the full 512 MiB is available. Note that kzm9g_defconfig still has CONFIG_MEMORY_START=0x41000000 and CONFIG_MEMORY_SIZE=0x1f000000, so before the advent of DT we scribbled over the last 8 MiB, too. Signed-off-by:
-
Geert Uytterhoeven authored
Traditionally, the first 16 MiB of RAM was reserved for the RT processor. However, this is incompatible with CONFIG_AUTO_ZRELADDR=y, which requires that the start address of physical memory is a multiple of 128 MiB. As CONFIG_AUTO_ZRELADDR=y is enabled for multi-platform kernels, declare RAM to start at 0x40000000. While at it, reclaim the last 8 MiB of RAM, too, so the full 512 MiB is available. Note that kzm9g_defconfig still has CONFIG_MEMORY_START=0x41000000 and CONFIG_MEMORY_SIZE=0x1f000000, so before the advent of DT we scribbled over the last 8 MiB, too. Signed-off-by:
-
Ulrich Hecht authored
Specifies clock sources and register bits. Signed-off-by:
Ulrich Hecht <ulrich.hecht+renesas@gmail.com> [geert: Drop renesas,src-shift/renesas,src-width, pad to 4 or 8 parents] Signed-off-by:
-
Geert Uytterhoeven authored
This clock drives the irqpin controller modules. Before, it was assumed enabled by the bootloader or reset state. By making it available to the driver, we make sure it gets enabled when needed, and allow it to be managed by system or runtime PM. Signed-off-by:
-
Laurent Pinchart authored
Enable the kzm9g touchscreen controller in the board's DT file. Signed-off-by:
-
Geert Uytterhoeven authored
Add a DT node for the R2025D real-time clock, which is connected to i2c0. Signed-off-by:
-
Geert Uytterhoeven authored
Add a DT node for the ADXL345 three-axis digital accelerometer sensor, which is connected to i2c0. As trivial i2c devices are matched against the first compatible entry only, compatibility is declared with "adi,adxl34x" only for now. Signed-off-by:
-
Geert Uytterhoeven authored
Add a DT node for the AK8975 magnetometer sensor, which is connected to i2c0. Signed-off-by:
-
Geert Uytterhoeven authored
While at it rename the ak4648 node to "codec" to describe the device's function instead of its model, and move its device-specific property after its generic properties. Signed-off-by:
-
Laurent Pinchart authored
The sh73a0 INTC can't mask interrupts properly most likely due to a hardware bug. Set the control-parent property to delegate masking to the parent interrupt controller. Signed-off-by:
-
Ulrich Hecht authored
This adds the remaining DIV6 clocks and all possible parents for the SUB clock. Signed-off-by:
-
Linus Torvalds authored
.. after extensive statistical analysis of my G+ polling, I've come to the inescapable conclusion that internet polls are bad. Big surprise. But "Hurr durr I'ma sheep" trounced "I like online polls" by a 62-to-38% margin, in a poll that people weren't even supposed to participate in. Who can argue with solid numbers like that? 5,796 votes from people who can't even follow the most basic directions? In contrast, "v4.0" beat out "v3.20" by a slimmer margin of 56-to-44%, but with a total of 29,110 votes right now. Now, arguably, that vote spread is only about 3,200 votes, which is less than the almost six thousand votes that the "please ignore" poll got, so it could be considered noise. But hey, I asked, so I'll honor the votes.
-
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4Linus Torvalds authored
Pull ext4 fixes from Ted Ts'o: "Ext4 bug fixes. We also reserved code points for encryption and read-only images (for which the implementation is mostly just the reserved code point for a read-only feature :-)" * tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: ext4: fix indirect punch hole corruption ext4: ignore journal checksum on remount; don't fail ext4: remove duplicate remount check for JOURNAL_CHECKSUM change ext4: fix mmap data corruption in nodelalloc mode when blocksize < pagesize ext4: support read-only images ext4: change to use setup_timer() instead of init_timer() ext4: reserve codepoints used by the ext4 encryption feature jbd2: complain about descriptor block checksum errors
-
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfsLinus Torvalds authored
Pull more vfs updates from Al Viro: "Assorted stuff from this cycle. The big ones here are multilayer overlayfs from Miklos and beginning of sorting ->d_inode accesses out from David" * 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (51 commits) autofs4 copy_dev_ioctl(): keep the value of ->size we'd used for allocation procfs: fix race between symlink removals and traversals debugfs: leave freeing a symlink body until inode eviction Documentation/filesystems/Locking: ->get_sb() is long gone trylock_super(): replacement for grab_super_passive() fanotify: Fix up scripted S_ISDIR/S_ISREG/S_ISLNK conversions Cachefiles: Fix up scripted S_ISDIR/S_ISREG/S_ISLNK conversions VFS: (Scripted) Convert S_ISLNK/DIR/REG(dentry->d_inode) to d_is_*(dentry) SELinux: Use d_is_positive() rather than testing dentry->d_inode Smack: Use d_is_positive() rather than testing dentry->d_inode TOMOYO: Use d_is_dir() rather than d_inode and S_ISDIR() Apparmor: Use d_is_positive/negative() rather than testing dentry->d_inode Apparmor: mediated_filesystem() should use dentry->d_sb not inode->i_sb VFS: Split DCACHE_FILE_TYPE into regular and special types VFS: Add a fallthrough flag for marking virtual dentries VFS: Add a whiteout dentry type VFS: Introduce inode-getting helpers for layered/unioned fs environments Infiniband: Fix potential NULL d_inode dereference posix_acl: fix reference leaks in posix_acl_create autofs4: Wrong format for printing dentry ...
-
- 22 Feb, 2015 15 commits
-
-
git://ftp.arm.linux.org.uk/~rmk/linux-armLinus Torvalds authored
Pull ARM fix from Russell King: "Just one fix this time around. __iommu_alloc_buffer() can cause a BUG() if dma_alloc_coherent() is called with either __GFP_DMA32 or __GFP_HIGHMEM set. The patch from Alexandre addresses this" * 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: ARM: 8305/1: DMA: Fix kzalloc flags in __iommu_alloc_buffer()
-
Al Viro authored
X-Coverup: just ask spender Cc: stable@vger.kernel.org Signed-off-by:Al Viro <viro@zeniv.linux.org.uk>
-
Al Viro authored
use_pde()/unuse_pde() in ->follow_link()/->put_link() resp. Cc: stable@vger.kernel.org Signed-off-by: -
Al Viro authored
As it is, we have debugfs_remove() racing with symlink traversals. Supply ->evict_inode() and do freeing there - inode will remain pinned until we are done with the symlink body. And rip the idiocy with checking if dentry is positive right after we'd verified debugfs_positive(), which is a stronger check... Cc: stable@vger.kernel.org Signed-off-by: -
Al Viro authored
Signed-off-by: -
Konstantin Khlebnikov authored
I've noticed significant locking contention in memory reclaimer around sb_lock inside grab_super_passive(). Grab_super_passive() is called from two places: in icache/dcache shrinkers (function super_cache_scan) and from writeback (function __writeback_inodes_wb). Both are required for progress in memory allocator. Grab_super_passive() acquires sb_lock to increment sb->s_count and check sb->s_instances. It seems sb->s_umount locked for read is enough here: super-block deactivation always runs under sb->s_umount locked for write. Protecting super-block itself isn't a problem: in super_cache_scan() sb is protected by shrinker_rwsem: it cannot be freed if its slab shrinkers are still active. Inside writeback super-block comes from inode from bdi writeback list under wb->list_lock. This patch removes locking sb_lock and checks s_instances under s_umount: generic_shutdown_super() unlinks it under sb->s_umount locked for write. New variant is called trylock_super() and since it only locks semaphore, callers must call up_read(&sb->s_umount) instead of drop_super(sb) when they're done. Signed-off-by:
Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Signed-off-by:
-
David Howells authored
Fanotify probably doesn't want to watch autodirs so make it use d_can_lookup() rather than d_is_dir() when checking a dir watch and give an error on fake directories. Signed-off-by:
David Howells <dhowells@redhat.com> Signed-off-by:
-
David Howells authored
Fix up the following scripted S_ISDIR/S_ISREG/S_ISLNK conversions (or lack thereof) in cachefiles: (1) Cachefiles mostly wants to use d_can_lookup() rather than d_is_dir() as it doesn't want to deal with automounts in its cache. (2) Coccinelle didn't find S_IS* expressions in ASSERT() statements in cachefiles. Signed-off-by: -
David Howells authored
Convert the following where appropriate: (1) S_ISLNK(dentry->d_inode) to d_is_symlink(dentry). (2) S_ISREG(dentry->d_inode) to d_is_reg(dentry). (3) S_ISDIR(dentry->d_inode) to d_is_dir(dentry). This is actually more complicated than it appears as some calls should be converted to d_can_lookup() instead. The difference is whether the directory in question is a real dir with a ->lookup op or whether it's a fake dir with a ->d_automount op. In some circumstances, we can subsume checks for dentry->d_inode not being NULL into this, provided we the code isn't in a filesystem that expects d_inode to be NULL if the dirent really *is* negative (ie. if we're going to use d_inode() rather than d_backing_inode() to get the inode pointer). Note that the dentry type field may be set to something other than DCACHE_MISS_TYPE when d_inode is NULL in the case of unionmount, where the VFS manages the fall-through from a negative dentry to a lower layer. In such a case, the dentry type of the negative union dentry is set to the same as the type of the lower dentry. However, if you know d_inode is not NULL at the call site, then you can use the d_is_xxx() functions even in a filesystem. There is one further complication: a 0,0 chardev dentry may be labelled DCACHE_WHITEOUT_TYPE rather than DCACHE_SPECIAL_TYPE. Strictly, this was intended for special directory entry types that don't have attached inodes. The following perl+coccinelle script was used: use strict; my @callers; open($fd, 'git grep -l \'S_IS[A-Z].*->d_inode\' |') || die "Can't grep for S_ISDIR and co. callers"; @callers = <$fd>; close($fd); unless (@callers) { print "No matches\n"; exit(0); } my @cocci = ( '@@', 'expression E;', '@@', '', '- S_ISLNK(E->d_inode->i_mode)', '+ d_is_symlink(E)', '', '@@', 'expression E;', '@@', '', '- S_ISDIR(E->d_inode->i_mode)', '+ d_is_dir(E)', '', '@@', 'expression E;', '@@', '', '- S_ISREG(E->d_inode->i_mode)', '+ d_is_reg(E)' ); my $coccifile = "tmp.sp.cocci"; open($fd, ">$coccifile") || die $coccifile; print($fd "$_\n") || die $coccifile foreach (@cocci); close($fd); foreach my $file (@callers) { chomp $file; print "Processing ", $file, "\n"; system("spatch", "--sp-file", $coccifile, $file, "--in-place", "--no-show-diff") == 0 || die "spatch failed"; } [AV: overlayfs parts skipped] Signed-off-by: -
David Howells authored
Use d_is_positive() rather than testing dentry->d_inode in SELinux to get rid of direct references to d_inode outside of the VFS. Signed-off-by:
-
David Howells authored
Use d_is_positive() rather than testing dentry->d_inode in Smack to get rid of direct references to d_inode outside of the VFS. Signed-off-by:
-
David Howells authored
Use d_is_dir() rather than d_inode and S_ISDIR(). Note that this will include fake directories such as automount triggers. Signed-off-by:
-
David Howells authored
Use d_is_positive(dentry) or d_is_negative(dentry) rather than testing dentry->d_inode as the dentry may cover another layer that has an inode when the top layer doesn't or may hold a 0,0 chardev that's actually a whiteout. Signed-off-by:
-
David Howells authored
mediated_filesystem() should use dentry->d_sb not dentry->d_inode->i_sb and should avoid file_inode() also since it is really dealing with the path. Signed-off-by:
-
David Howells authored
Split DCACHE_FILE_TYPE into DCACHE_REGULAR_TYPE (dentries representing regular files) and DCACHE_SPECIAL_TYPE (representing blockdev, chardev, FIFO and socket files). d_is_reg() and d_is_special() are added to detect these subtypes and d_is_file() is left as the union of the two. This allows a number of places that use S_ISREG(dentry->d_inode->i_mode) to use d_is_reg(dentry) instead. Signed-off-by:
-
