- 12 Apr, 2016 18 commits
-
-
Ville Syrjälä authored
During runtime PM we'll be reinitializing interrupt support from the ground up. However since the display power well will be off at that time, well end up with a ton of unclaimed register accesses from the display irq setup. Since we turned off the power well already before runtime suspend, we've flagged display irqs as disabled during runtime PM transitions. So we can just check that flag to see if we should do skip display irqs during irq setup. During driver load display irqs will be flagged as enabled since we've turned on the power well already, however the power well code will have skipped the display irq setup since irq support as a whole wasn't yet enabled when the power well was enabled. So we'll want to do the display irq setup in that case. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94164Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1460382992-28728-4-git-send-email-ville.syrjala@linux.intel.comReviewed-by:
Imre Deak <imre.deak@intel.com>
-
Ville Syrjälä authored
The vlv/chv display irq setup was a bit of mess after I ran out of steam when working on it last. Fix it up so that we just have a _reset() and _postinstall() hooks for the display irqs, and use those consistently. v2: Clear out pipestat_irq_mask[] and PIPE_FIFO_UNDERRUN_STATUS in vlv_display_irq_reset() (Imre) Signed-off-by: -
Ville Syrjälä authored
No clue what this is supposed to achieve. I think it's been there since the very beginning, so presumably some kind of kludge for very early silicon. Let's just throw it out. Signed-off-by:
-
Ville Syrjälä authored
The underruns we were seeing when enabling eDP port A on ILK seem to have been caused by prematurely clearing the LP1+ watermark values when disabling LP1+ watermarks. Now that the watermarks are handled properly, we can rip out the underrun suppression around the port A enable. We still need to worry about the underruns on FDI when enabling the eDP PLL. But as Bspec tells us, we can avoid that by a vblank wait on the pipe driving FDI just prior to enabling the eDP PLL. Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
-
Ville Syrjälä authored
Once again ILK is unhappy if we clear out the LP1+ watermark levels outright, and instead we must disable the levels we don't want while still leaving the actual programmed watermark levels intact. Fixes underruns on the already enabled pipe when programming watermarks while enabling the second pipe. Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Matt Roper <matthew.d.roper@intel.com> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93787Signed-off-by:
-
Ville Syrjälä authored
Take a bigger hammer to the underrun suppression on ILK. Instead of trying to suppress them at specific points in the modeset sequence just silence them across the entire sequence. This gets rid of some underruns at least on my ILK. Note that this changes SNB and IVB to follow the same approach just to keep the code less convoluted. The difference is that on those platforms we won't suppress CPU underruns for port A since it doesn't seem to be necessary. My ILK has port A eDP and two PCH HDMI ports, so I can't be sure this is as effective on other PCH port types. Perhaps we still need some of Daniel's extra vblank waits [2]? I've still been able to trigger an underrun on the other pipe, but fixing that perhaps needs the LP1+ disable trick I implemented here [1] which never got merged. A few details which hamper stress testing on my ILK are that sometimes the PCH transcoder gets messed up and refuses to shut down, and sometimes even the panel power sequencer apparently gets stuck on the always on position. [1] https://lists.freedesktop.org/archives/intel-gfx/2014-March/041317.html [2] https://lists.freedesktop.org/archives/intel-gfx/2016-January/086397.html v2: Add a note that we also get underruns when enabling PCH ports Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
-
Tvrtko Ursulin authored
Rather than blindly waking up all forcewake domains on command submission, we can teach each engine what is (or are) the correct one to take. On platforms with multiple forcewake domains like VLV, CHV, SKL and BXT, this has the potential of lowering the GPU and CPU power use and submission latency. To implement it we add a function named intel_uncore_forcewake_for_reg whose purpose is to query which forcewake domains need to be taken to read or write a specific register with raw mmio accessors. These enables the execlists engine setup to query which forcewake domains are relevant per engine on the currently running platform. v2: * Kerneldoc. * Split from intel_uncore.c macro extraction, WARN_ON, no warns on old platforms. (Chris Wilson) v3: * Single domain per engine, mention all registers, bi-directional function and a new name, fix handling of gen6 and gen7 writes. (Chris Wilson) Signed-off-by:Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by:
Chris Wilson <chris@chris-wilson.co.uk> Link: http://patchwork.freedesktop.org/patch/msgid/1460468251-14069-1-git-send-email-tvrtko.ursulin@linux.intel.com
-
Tvrtko Ursulin authored
Chris Wilson points out that we can remove them from the array since they are always written to with raw accessors. Signed-off-by:
-
Tvrtko Ursulin authored
Knowledge of which register per platform belonds in which forcewake domain was embedded in the MMIO accessors themselves. Extract it into standalone macros so they can be used from new code in the following patches. This causes GCC to compile some of the MMIO accessors slightly differently and grows the code a tiny amount. But none of the growth is on the fast-path so it does not matter hugely. Affected sizes before: 00000000000026f0 00000000000001a5 t gen6_read16 0000000000002390 00000000000001a5 t gen6_read32 00000000000028a0 00000000000001a5 t gen6_read64 00000000000061d0 000000000000019e t gen8_write16 0000000000006510 000000000000019d t gen8_write32 0000000000006370 000000000000019d t gen8_write64 00000000000021f0 000000000000019d t gen8_write8 Affected sizes after: 0000000000002840 00000000000001aa t gen6_read16 00000000000024e0 00000000000001a9 t gen6_read32 00000000000029f0 00000000000001a9 t gen6_read64 0000000000004f20 00000000000001b5 t gen8_write16 0000000000004ba0 00000000000001b4 t gen8_write32 00000000000050e0 00000000000001b4 t gen8_write64 0000000000004d60 00000000000001b4 t gen8_write8 Other MMIO accessors are not affected in size. Signed-off-by:
-
Tvrtko Ursulin authored
On platforms with multiple forcewake domains it seems more efficient to request all desired ones and then to wait for acks to avoid needlessly serializing on each domain. v2: Rebase. Signed-off-by:
-
Tvrtko Ursulin authored
As the vast majority of users do not use the domain id variable, we can eliminate it from the iterator and also change the latter using the same principle as was recently done for for_each_engine. For a couple of callers which do need the domain mask, store it in the domain array (which already has the domain id), then both can be retrieved thence. Result is clearer code and smaller generated binary, especially in the tight fw get/put loops. Also, relationship between domain id and mask is no longer assumed in the macro. v2: Improve grammar in the commit message and rename the iterator to for_each_fw_domain_masked for consistency. (Dave Gordon) Signed-off-by:Dave Gordon <david.s.gordon@intel.com>
-
Tvrtko Ursulin authored
Because it is based on jiffies, current implementation releases the forcewake at any time between straight away and between 1ms and 10ms, depending on the kernel configuration (CONFIG_HZ). This is probably not what has been desired, since the dynamics of keeping parts of the GPU awake should not be correlated with this kernel configuration parameter. Change the auto-release mechanism to use hrtimers and set the timeout to 1ms with a 1ms of slack. This should make the GPU power consistent across kernel configs, and timer slack should enable some timer coalescing where multiple force-wake domains exist, or with unrelated timers. For GlBench/T-Rex this decreases the number of forcewake releases from ~480 to ~300 per second, and for a heavy combined OGL/OCL test from ~670 to ~360 (HZ=1000 kernel). Even though this reduction can be attributed to the average release period extending from 0-1ms to 1-2ms, as discussed above, it will make the forcewake timeout consistent for different CONFIG_HZ values. Real life measurements with the above workload has shown that, with this patch, both manage to auto-release the forcewake between 2-4 times per 10ms, even though the number of forcewake gets is dramatically different. T-Rex requests between 5-10 explicit gets and 5-10 implict gets in each 10ms period, while the OGL/OCL test requests 250 and 380 times in the same period. The two data points together suggest that the nature of the forwake accesses is bursty and that further changes and potential timeout extensions, or moving the start of timeout from the first to the last automatic forcewake grab, should be carefully measured for power and performance effects. v2: * Commit spelling. (Dave Gordon) * More discussion on numbers in the commit. (Chris Wilson) Signed-off-by:
-
Ville Syrjälä authored
We've had problems on several occasions with using the panel type from the VBT block 40. Usually it seems to be 2, which often doesn't give us the correct timings for the panel. After some more digging I found a way to get a panel type via the OpRegion SWSCI GBDA "Get Panel Details" method. Let's try to use it. The spec has this to say about the output: "Bits [15:8] - Panel Type Bits contain the panel type user setting from CMOS 00h = Not Valid, use default Panel Type & Timings from VBT 01h - 0Fh = Panel Number" Another version of the spec lists the valid range as 1-16, which makes more sense since VBT supports 16 panels. Based on actual results from Rob's G45, 1-16 is what we need to accept. The other bits in the output don't look relevant for the problem at hand. The input is specified as: "Bits [31:4] - Reserved Reserved (must be zero) Bits [3:0] - Panel Number These bits contain the sequential index of Panel, starting at 0 and counting upwards from the first integrated Internal Flat-Panel Display Encoder present, and then from the first external Display Encoder (e.g., S/DVO-B then S/DVO-C) which supports Internal Flat-Panels. 0h - 0Fh = Panel number" For now I've just hardcoded the input panel number as 0. That would seem like a decent choise for LVDS. Not so sure about eDP when port != A. v2: Accept values 1-16 Filter out bogus results in opregion code (Jani) Add debug logging for all the different branches (Jani) Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Rob Kramer <rob@solution-space.com> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94825Signed-off-by:Jani Nikula <jani.nikula@intel.com> Tested-by:
Rob Kramer <rob@solution-space.com>
-
Ville Syrjälä authored
Store the extracted panel_type under dev_priv.vbt instead of keeping around a static variable for it. Cc: Rob Kramer <rob@solution-space.com> Signed-off-by:
-
Ville Syrjälä authored
VBT can only contain 16 panel entries, indexed with the panel_type. To play it safe we should reject panel_type > 0xf, so that we don't read past the valid data. v2: Add debug logging (Jani) Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Rob Kramer <rob@solution-space.com> Signed-off-by:
-
Ville Syrjälä authored
There's no real reason the user should care that we're about to fall back to bitbanging, so let's change the message from DRM_INFO to DRM_DEBUG_KMS. Signed-off-by:
-
Ville Syrjälä authored
When the GMBUS based i2c transfer times out, we try to fall back to bit-banging and retry the operation that way. However if the bit-banging attempt also fails, we should probably go back to the GMBUS method for the next attempt. Maybe there simply wasn't anyone one the bus at this time. There's also a bit of a mess going on with the force_bit handling. It's supposed to be a ref count actually, and it is as far as intel_gmbus_force_bit() is concerned. But it's treated as just a flag by the timeout based bit-banging fallback. I suppose that's fine since we should never end up in the timeout fallback case if force_bit was already non-zero. However now that we want to restore things back to where they were after the bit-banging attempt failed, we're going to have to do things a bit differently to avoid clobbering the force_bit count as set up by intel_gmbus_force_bit(). So let's dedicate the high bit as a flag for the low level timeout based fallback and treat the rest of the bits as a ref count just as before. Signed-off-by:
-
Ville Syrjälä authored
Extend the protection of gmbus_mutex around the force_bit RMW in intel_gmbus_force_bit(), in case someone gets the idea of calling it from a separate thread while there's other stuff happening on the same bus. Signed-off-by:
-
- 11 Apr, 2016 20 commits
-
-
Chris Wilson authored
Since we only ever use the drm_i915_private from the stored i915_mm_struct->dev, save some electrons by storing the right backpointer. Signed-off-by:
Michał Winiarski <michal.winiarski@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1459864801-28606-3-git-send-email-chris@chris-wilson.co.uk
-
Chris Wilson authored
Holding a reference to the containing task_struct is not sufficient to prevent the mm_struct from being reaped under memory pressure. If this happens whilst we are calling get_user_pages(), explosions erupt - sometimes an immediate GPF, sometimes page flag corruption. To prevent the target mm from being reaped as we are reading from it, acquire a reference before we begin. Testcase: igt/gem_shrink/*userptr Signed-off-by:
-
Chris Wilson authored
In order to ensure that all invalidations are completed before the operation returns to userspace (i.e. before the munmap() syscall returns) we need to wait upon the outstanding operations. We are allowed to block inside the invalidate_range_start callback, and as struct_mutex is the inner lock with mmap_sem we can wait upon the struct_mutex without provoking lockdep into warning about a deadlock. However, we don't actually want to wait upon outstanding rendering whilst holding the struct_mutex if we can help it otherwise we also block other processes from submitting work to the GPU. So first we do a wait without the lock and then when we reacquire the lock, we double check that everything is ready for removing the invalidated pages. Finally to wait upon the outstanding unpinning tasks, we create a private workqueue as a means to conveniently wait upon all at once. The drawback is that this workqueue is per-mm, so any threads concurrently invalidating objects will wait upon each other. The advantage of using the workqueue is that we can wait in parallel for completion of rendering and unpinning of several objects (of particular importance if the process terminates with a whole mm full of objects). v2: Apply a cup of tea to the changelog. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94699 Testcase: igt/gem_userptr_blits/sync-unmap-cycles Signed-off-by:
-
Daniel Vetter authored
Signed-off-by:Daniel Vetter <daniel.vetter@ffwll.ch>
-
Daniel Vetter authored
Linux 4.6-rc3 Backmerge requested by Chris Wilson to make his patches apply cleanly. Tiny conflict in vmalloc.c with the (properly acked and all) patch in drm-intel-next: commit 4da56b99 Author: Chris Wilson <chris@chris-wilson.co.uk> Date: Mon Apr 4 14:46:42 2016 +0100 mm/vmap: Add a notifier for when we run out of vmap address space and Linus' tree. Signed-off-by:
Daniel Vetter <daniel.vetter@intel.com>
-
Chris Wilson authored
If we want a contiguous mapping of a single page sized object, we can forgo using vmap() and just use a regular kmap(). Note that this is only suitable if the desired pgprot_t is compatible. v2: Use is_vmalloc_addr() Signed-off-by:
Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
-
Chris Wilson authored
I have instances where I want to use drm_malloc_ab() but with a custom gfp mask. And with those, where I want a temporary allocation, I want to try a high-order kmalloc() before using a vmalloc(). So refactor my usage into drm_malloc_gfp(). Signed-off-by:
Dave Airlie <airlied@redhat.com> Link: http://patchwork.freedesktop.org/patch/msgid/1460113874-17366-6-git-send-email-chris@chris-wilson.co.uk
-
Chris Wilson authored
When called because we have run out of vmap address space, we only need to recover objects that have vmappings and not all. v2: Start using is_vmalloc_addr() Signed-off-by:
-
Chris Wilson authored
We now have two implementations for vmapping a whole object, one for dma-buf and one for the ringbuffer. If we couple the mapping into the obj->pages lifetime, then we can reuse an obj->mapping for both and at the same time couple it into the shrinker. There is a third vmapping routine in the cmdparser that maps only a range within the object, for the time being that is left alone, but will eventually use these routines in order to cache the mapping between invocations. v2: Mark the failable kmalloc() as __GFP_NOWARN (vsyrjala) v3: Call unpin_vmap from the right dmabuf unmapper v4: Rename vmap to map as we don't wish to imply the type of mapping involved, just that it contiguously maps the object into kernel space. Add kerneldoc and lockdep annotations Signed-off-by:
-
Chris Wilson authored
After we pin the ringbuffer into the GGTT, all error paths need to unpin it again. Move this common step into one block, and make the unable to iomap error code consistent (i.e. treat it as out of memory to avoid confusing it with a invalid argument). Signed-off-by:
-
Chris Wilson authored
We only need the struct_mutex to manipulate the pages_pin_count on the object, we do not need to hold our BKL when freeing the exported scatterlist. Signed-off-by:
-
Tim Gore authored
This is to fix a GPU hang seen with mid thread pre-emption and pooled EUs. v2. Use IS_BXT_REVID instead of IS_BROXTON and INTEL_REVID v3. And use correct type for register addresses Signed-off-by:
Tim Gore <tim.gore@intel.com> Reviewed-by:
Arun Siluvery <arun.siluvery@linux.intel.com> Signed-off-by:
-
Dongwon Kim authored
For BXT, description of polarities of PORT_PLL_REF_SEL has been reversed for newer Gen9LP steppings according to the recent update in Bspec. This bit now should be set for "Non-SSC" mode for all Gen9LP starting from B0 stepping. v2: Only B0 and newer stepping should be affected by this change. Signed-off-by:
Dongwon Kim <dongwon.kim@intel.com> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94866Reviewed-by:
-
Maarten Lankhorst authored
Check functions are used by atomic to see if the new state will be allowed. There's also a hw state checker which checks afterwards that the committed state is correct. Rename it to hw state verifier to reduce some confusion. Suggested-by:
Matt Roper <matthew.d.roper@intel.com> Signed-off-by:
Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/56FB8785.8020506@linux.intel.comReviewed-by:
-
Maarten Lankhorst authored
The modeset state verifier no longer has full access to the hardware, instead it should only verify affected crtc's. Looking for disabled stuff can be verified immediately after all crtc disables have completed, while each enabled crtc can be verified right after being enabled. Signed-off-by:
-
Maarten Lankhorst authored
This will make it easier to keep the crtc checker when atomic commit is reworked for asynchronous commits. This prevents checking crtc's that were not part of the state. It's safe to verify disabled encoders, connectors and dpll's that are not part of the state, because during modeset connection_mutex is held. Signed-off-by:
-
Linus Torvalds authored
-
git://ftp.arm.linux.org.uk/~rmk/linux-armLinus Torvalds authored
Pull ARM fixes from Russell King: "A couple of small fixes, and wiring up the new syscalls which appeared during the merge window" * 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: ARM: 8550/1: protect idiv patching against undefined gcc behavior ARM: wire up preadv2 and pwritev2 syscalls ARM: SMP enable of cache maintanence broadcast
-
git://git.linaro.org/people/ulf.hansson/mmcLinus Torvalds authored
Pull MMC fixes from Ulf Hansson: "Here are a couple of mmc fixes intended for v4.6 rc3: MMC host: - sdhci: Fix regression setting power on Trats2 board - sdhci-pci: Add support and PCI IDs for more Broxton host controllers" * tag 'mmc-v4.6-rc1' of git://git.linaro.org/people/ulf.hansson/mmc: mmc: sdhci-pci: Add support and PCI IDs for more Broxton host controllers mmc: sdhci: Fix regression setting power on Trats2 board
-
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linuxLinus Torvalds authored
Pull i2c fixes from Wolfram Sang: "Some bugfixes from I2C: - fix a uevent triggered boot problem by removing a useless debug print - fix sysfs-attributes of the new i2c-demux-pinctrl driver to follow standard kernel behaviour - fix a potential division-by-zero error (needed two takes)" * 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: i2c: jz4780: really prevent potential division by zero Revert "i2c: jz4780: prevent potential division by zero" i2c: jz4780: prevent potential division by zero i2c: mux: demux-pinctrl: Update docs to new sysfs-attributes i2c: mux: demux-pinctrl: Clean up sysfs attributes i2c: prevent endless uevent loop with CONFIG_I2C_DEBUG_CORE
-
- 10 Apr, 2016 1 commit
-
-
Linus Torvalds authored
This reverts commit 1028b55b. It's broken: it makes ext4 return an error at an invalid point, causing the readdir wrappers to write the the position of the last successful directory entry into the position field, which means that the next readdir will now return that last successful entry _again_. You can only return fatal errors (that terminate the readdir directory walk) from within the filesystem readdir functions, the "normal" errors (that happen when the readdir buffer fills up, for example) happen in the iterorator where we know the position of the actual failing entry. I do have a very different patch that does the "signal_pending()" handling inside the iterator function where it is allowable, but while that one passes all the sanity checks, I screwed up something like four times while emailing it out, so I'm not going to commit it today. So my track record is not good enough, and the stars will have to align better before that one gets committed. And it would be good to get some review too, of course, since celestial alignments are always an iffy debugging model. IOW, let's just revert the commit that caused the problem for now. Reported-by:
Greg Thelen <gthelen@google.com> Cc: Theodore Ts'o <tytso@mit.edu> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
- 09 Apr, 2016 1 commit
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linuxLinus Torvalds authored
Pull parisc fixes from Helge Deller: "Since commit 0de79858 ("parisc: Use generic extable search and sort routines") module loading is boken on parisc, because the parisc module loader wasn't prepared for the new R_PARISC_PCREL32 relocations. In addition, due to that breakage, Mikulas Patocka noticed that handling exceptions from modules probably never worked on parisc. It was just masked by the fact that exceptions from modules don't happen during normal use. This patch series fixes those issues and survives the tests of the lib/test_user_copy kernel module test. Some patches are tagged for stable" * 'parisc-4.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux: parisc: Update comment regarding relative extable support parisc: Unbreak handling exceptions from kernel modules parisc: Fix kernel crash with reversed copy_from_user() parisc: Avoid function pointers for kernel exception routines parisc: Handle R_PARISC_PCREL32 relocations in kernel modules
-
