- 26 Mar, 2019 8 commits
-
-
Xin Long authored
When running a syz script, a panic occurred: [ 156.088228] BUG: KASAN: use-after-free in tipc_disc_timeout+0x9c9/0xb20 [tipc] [ 156.094315] Call Trace: [ 156.094844] <IRQ> [ 156.095306] dump_stack+0x7c/0xc0 [ 156.097346] print_address_description+0x65/0x22e [ 156.100445] kasan_report.cold.3+0x37/0x7a [ 156.102402] tipc_disc_timeout+0x9c9/0xb20 [tipc] [ 156.106517] call_timer_fn+0x19a/0x610 [ 156.112749] run_timer_softirq+0xb51/0x1090 It was caused by the netns freed without deleting the discoverer timer, while later on the netns would be accessed in the timer handler. The timer should have been deleted by tipc_net_stop() when cleaning up a netns. However, tipc has been able to enable a bearer and start d->timer without the local node_addr set since Commit 52dfae5c ("tipc: obtain node identity from interface by default"), which caused the timer not to be deleted in tipc_net_stop() then. So fix it in tipc_net_stop() by changing to check local node_id instead of local node_addr, as Jon suggested. While at it, remove the calling of tipc_nametbl_withdraw() there, since tipc_nametbl_stop() will take of the nametbl's freeing after. Fixes: 52dfae5c ("tipc: obtain node identity from interface by default") Reported-by: syzbot+a25307ad099309f1c2b9@syzkaller.appspotmail.com Signed-off-by:
Xin Long <lucien.xin@gmail.com> Acked-by:
Ying Xue <ying.xue@windriver.com> Acked-by:
Jon Maloy <jon.maloy@ericsson.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Dmitry Bezrukov authored
New device of QNAP based on aqc111u Add this ID to blacklist of cdc_ether driver as well Signed-off-by:
Dmitry Bezrukov <dmitry.bezrukov@aquantia.com> Signed-off-by:
-
Leslie Monis authored
RFC 8033 replaces the IETF draft for PIE Signed-off-by:
Leslie Monis <lesliemonis@gmail.com> Signed-off-by:
-
Christian Lamparter authored
This patch implements accessors for the QCA8337 MDIO access through the MDIO_MASTER register, which makes it possible to access the PHYs on slave-bus through the switch. In cases where the switch ports are already mapped via external "phy-phandles", the internal mdio-bus is disabled in order to prevent a duplicated discovery and enumeration of the same PHYs. Don't use mixed external and internal mdio-bus configurations, as this is not supported by the hardware. Signed-off-by:
Christian Lamparter <chunkeey@gmail.com> Signed-off-by:
-
Christian Lamparter authored
This belated patch implements Andrew Lunn's request of "remove the phy_read() and phy_write() functions." <https://lore.kernel.org/patchwork/comment/902734/> While seemingly harmless, this causes the switch's user port PHYs to get registered twice. This is because the DSA subsystem will create a slave mdio-bus not knowing that the qca8k_phy_(read|write) accessors operate on the external mdio-bus. So the same "bus" gets effectively duplicated. Cc: stable@vger.kernel.org Fixes: 6b93fb46 ("net-next: dsa: add new driver for qca8xxx family") Signed-off-by:
-
Christian Lamparter authored
This patch updates the qca8k's binding to document to the approach for using the internal mdio-bus of the supported qca8k switches. Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Christian Lamparter authored
In the example, the phy at phy@0 is clashing with the switch0@0 at the same address. Usually, the switches are accessible through pseudo PHYs which in case of the qca8k are located at 0x10 - 0x18. Reviewed-by:
-
Heiner Kallweit authored
So far we effectively clear the BMCR register. Some PHY's can deal with this (e.g. because they reset BMCR to a default as part of a soft-reset) whilst on others this causes issues because e.g. the autoneg bit is cleared. Marvell is an example, see also thread [0]. So let's be a little bit more gentle and leave all bits we're not interested in as-is. This change is needed for PHY drivers to properly deal with the original patch. [0] https://marc.info/?t=155264050700001&r=1&w=2 Fixes: 6e2d85ec ("net: phy: Stop with excessive soft reset") Tested-by:
Phil Reid <preid@electromag.com.au> Tested-by:
liweihang <liweihang@hisilicon.com> Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by:
-
- 25 Mar, 2019 4 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpfDavid S. Miller authored
Alexei Starovoitov says: ==================== pull-request: bpf 2019-03-24 The following pull-request contains BPF updates for your *net* tree. The main changes are: 1) libbpf verision fix up from Daniel. 2) fix liveness propagation from Jakub. 3) fix verbose print of refcounted regs from Martin. 4) fix for large map allocations from Martynas. 5) fix use after free in sanitize_ptr_alu from Xu. ==================== Signed-off-by: -
Alexei Starovoitov authored
Daniel Borkmann says: ==================== First one is fixing version in Makefile and shared object and second one clarifies bump in version. Thanks! v1 -> v2: - Fix up soname, thanks Stanislav! ==================== Signed-off-by:Alexei Starovoitov <ast@kernel.org>
-
Daniel Borkmann authored
The current documentation suggests that we would need to bump the libbpf version on every change. Lets clarify this a bit more and reflect what we do today in practice, that is, bumping it once per development cycle. Fixes: 76d1b894 ("libbpf: Document API and ABI conventions") Reported-by:
Stanislav Fomichev <sdf@google.com> Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
-
Daniel Borkmann authored
Even though libbpf's versioning script for the linker (libbpf.map) is pointing to 0.0.2, the BPF_EXTRAVERSION in the Makefile has not been updated along with it and is therefore still on 0.0.1. While fixing up, I also noticed that the generated shared object versioning information is missing, typical convention is to have a linker name (libbpf.so), soname (libbpf.so.0) and real name (libbpf.so.0.0.2) for library management. This is based upon the LIBBPF_VERSION as well. The build will then produce the following bpf libraries: # ll libbpf* libbpf.a libbpf.so -> libbpf.so.0.0.2 libbpf.so.0 -> libbpf.so.0.0.2 libbpf.so.0.0.2 # readelf -d libbpf.so.0.0.2 | grep SONAME 0x000000000000000e (SONAME) Library soname: [libbpf.so.0] And install them accordingly: # rm -rf /tmp/bld; mkdir /tmp/bld; make -j$(nproc) O=/tmp/bld install Auto-detecting system features: ... libelf: [ on ] ... bpf: [ on ] CC /tmp/bld/libbpf.o CC /tmp/bld/bpf.o CC /tmp/bld/nlattr.o CC /tmp/bld/btf.o CC /tmp/bld/libbpf_errno.o CC /tmp/bld/str_error.o CC /tmp/bld/netlink.o CC /tmp/bld/bpf_prog_linfo.o CC /tmp/bld/libbpf_probes.o CC /tmp/bld/xsk.o LD /tmp/bld/libbpf-in.o LINK /tmp/bld/libbpf.a LINK /tmp/bld/libbpf.so.0.0.2 LINK /tmp/bld/test_libbpf INSTALL /tmp/bld/libbpf.a INSTALL /tmp/bld/libbpf.so.0.0.2 # ll /usr/local/lib64/libbpf.* /usr/local/lib64/libbpf.a /usr/local/lib64/libbpf.so -> libbpf.so.0.0.2 /usr/local/lib64/libbpf.so.0 -> libbpf.so.0.0.2 /usr/local/lib64/libbpf.so.0.0.2 Fixes: 1bf4b058 ("tools: bpftool: add probes for eBPF program types") Fixes: 1b76c13e ("bpf tools: Introduce 'bpf' library and add bpf feature check") Reported-by:
-
- 24 Mar, 2019 8 commits
-
-
Arnd Bergmann authored
clang produces a false-positive warning as it fails to notice that "lost = true" implies that "ret" is initialized: net/rxrpc/output.c:402:6: error: variable 'ret' is used uninitialized whenever 'if' condition is true [-Werror,-Wsometimes-uninitialized] if (lost) ^~~~ net/rxrpc/output.c:437:6: note: uninitialized use occurs here if (ret >= 0) { ^~~ net/rxrpc/output.c:402:2: note: remove the 'if' if its condition is always false if (lost) ^~~~~~~~~ net/rxrpc/output.c:339:9: note: initialize the variable 'ret' to silence this warning int ret, opt; ^ = 0 Rearrange the code to make that more obvious and avoid the warning. Signed-off-by:Arnd Bergmann <arnd@arndb.de> Reviewed-by:
Nathan Chancellor <natechancellor@gmail.com> Signed-off-by:
-
Jon Maloy authored
When checking the code with clang -Wsometimes-uninitialized we get the following warning: if (!tipc_link_is_establishing(l)) { ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~ net/tipc/node.c:847:46: note: uninitialized use occurs here tipc_bearer_xmit(n->net, bearer_id, &xmitq, maddr); net/tipc/node.c:831:2: note: remove the 'if' if its condition is always true if (!tipc_link_is_establishing(l)) { ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ net/tipc/node.c:821:31: note: initialize the variable 'maddr' to silence this warning struct tipc_media_addr *maddr; We fix this by initializing 'maddr' to NULL. For the matter of clarity, we also test if 'xmitq' is non-empty before we use it and 'maddr' further down in the function. It will never happen that 'xmitq' is non- empty at the same time as 'maddr' is NULL, so this is a sufficient test. Fixes: 598411d7 ("tipc: make resetting of links non-atomic") Reported-by: -
John Hurley authored
A new mirred action is created by the tcf_mirred_init function. This contains a list head struct which is inserted into a global list on successful creation of a new action. However, after a creation, it is still possible to error out and call the tcf_idr_release function. This, in turn, calls the act_mirr cleanup function via __tcf_idr_release and __tcf_action_put. This cleanup function tries to delete the list entry which is as yet uninitialised, leading to a NULL pointer exception. Fix this by initialising the list entry on creation of a new action. Bug report: BUG: unable to handle kernel NULL pointer dereference at 0000000000000008 PGD 8000000840c73067 P4D 8000000840c73067 PUD 858dcc067 PMD 0 Oops: 0002 [#1] SMP PTI CPU: 32 PID: 5636 Comm: handler194 Tainted: G OE 5.0.0+ #186 Hardware name: Dell Inc. PowerEdge R730/0599V5, BIOS 1.3.6 06/03/2015 RIP: 0010:tcf_mirred_release+0x42/0xa7 [act_mirred] Code: f0 90 39 c0 e8 52 04 57 c8 48 c7 c7 b8 80 39 c0 e8 94 fa d4 c7 48 8b 93 d0 00 00 00 48 8b 83 d8 00 00 00 48 c7 c7 f0 90 39 c0 <48> 89 42 08 48 89 10 48 b8 00 01 00 00 00 00 ad de 48 89 83 d0 00 RSP: 0018:ffffac4aa059f688 EFLAGS: 00010282 RAX: 0000000000000000 RBX: ffff9dcd1b214d00 RCX: 0000000000000000 RDX: 0000000000000000 RSI: ffff9dcd1fa165f8 RDI: ffffffffc03990f0 RBP: ffff9dccf9c7af80 R08: 0000000000000a3b R09: 0000000000000000 R10: ffff9dccfa11f420 R11: 0000000000000000 R12: 0000000000000001 R13: ffff9dcd16b433c0 R14: ffff9dcd1b214d80 R15: 0000000000000000 FS: 00007f441bfff700(0000) GS:ffff9dcd1fa00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000008 CR3: 0000000839e64004 CR4: 00000000001606e0 Call Trace: tcf_action_cleanup+0x59/0xca __tcf_action_put+0x54/0x6b __tcf_idr_release.cold.33+0x9/0x12 tcf_mirred_init.cold.20+0x22e/0x3b0 [act_mirred] tcf_action_init_1+0x3d0/0x4c0 tcf_action_init+0x9c/0x130 tcf_exts_validate+0xab/0xc0 fl_change+0x1ca/0x982 [cls_flower] tc_new_tfilter+0x647/0x8d0 ? load_balance+0x14b/0x9e0 rtnetlink_rcv_msg+0xe3/0x370 ? __switch_to_asm+0x40/0x70 ? __switch_to_asm+0x34/0x70 ? _cond_resched+0x15/0x30 ? __kmalloc_node_track_caller+0x1d4/0x2b0 ? rtnl_calcit.isra.31+0xf0/0xf0 netlink_rcv_skb+0x49/0x110 netlink_unicast+0x16f/0x210 netlink_sendmsg+0x1df/0x390 sock_sendmsg+0x36/0x40 ___sys_sendmsg+0x27b/0x2c0 ? futex_wake+0x80/0x140 ? do_futex+0x2b9/0xac0 ? ep_scan_ready_list.constprop.22+0x1f2/0x210 ? ep_poll+0x7a/0x430 __sys_sendmsg+0x47/0x80 do_syscall_64+0x55/0x100 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Fixes: 4e232818 ("net: sched: act_mirred: remove dependency on rtnl lock") Signed-off-by:
John Hurley <john.hurley@netronome.com> Reviewed-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
-
Heiner Kallweit authored
Bartek reported that after few cable unplug/replug cycles suddenly replug isn't detected any longer. His system uses a RTL8106, I wasn't able to reproduce the issue with RTL8168g. According to his bisect the referenced commit caused the regression. As Realtek doesn't release datasheets or errata it's hard to say what's the actual root cause, but this change was reported to fix the issue. Fixes: 38caff5a ("r8169: handle all interrupt events in the hard irq handler") Reported-by:
Bartosz Skrzypczak <barteks2x@gmail.com> Suggested-by:
-
Wen Yang authored
The call to of_get_child_by_name returns a node pointer with refcount incremented thus it must be explicitly decremented after the last usage. Detected by coccinelle with the following warnings: ./drivers/net/ethernet/ti/netcp_ethss.c:3661:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 3654, but without a corresponding object release within this function. ./drivers/net/ethernet/ti/netcp_ethss.c:3665:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 3654, but without a corresponding object release within this function. Signed-off-by:
Wen Yang <wen.yang99@zte.com.cn> Cc: Wingman Kwok <w-kwok2@ti.com> Cc: Murali Karicheri <m-karicheri2@ti.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by:
-
Wen Yang authored
The call to ehea_get_eth_dn returns a node pointer with refcount incremented thus it must be explicitly decremented after the last usage. Detected by coccinelle with the following warnings: ./drivers/net/ethernet/ibm/ehea/ehea_main.c:3163:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 3154, but without a corresponding object release within this function. Signed-off-by:
-
Wen Yang authored
The call to of_parse_phandle returns a node pointer with refcount incremented thus it must be explicitly decremented after the last usage. Detected by coccinelle with the following warnings: ./drivers/net/ethernet/xilinx/xilinx_axienet_main.c:1624:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1569, but without a corresponding object release within this function. Signed-off-by:
-
Florian Fainelli authored
After 90eff909 ("net: phy: Allow splitting MDIO bus/device support from PHYs") the various MDIO bus drivers were no longer parented with config PHYLIB but with config MDIO_BUS which is not a menuconfig, fix this by depending on MDIO_DEVICE which is a menuconfig. This is visually nicer and less confusing for users. Fixes: 90eff909 ("net: phy: Allow splitting MDIO bus/device support from PHYs") Signed-off-by:
-
- 22 Mar, 2019 2 commits
-
-
Heiner Kallweit authored
After the original patch network starts to crash on heavy load. It's not fully clear why this additional register read has such side effects, but removing it fixes the issue. Thanks also to Alex for his contribution and hints. [0] https://marc.info/?t=155268170400002&r=1&w=2 Fixes: e782410e ("r8169: improve spurious interrupt detection") Reported-by:
VDR User <user.vdr@gmail.com> Tested-by:
Alexander Duyck <alexander.h.duyck@linux.intel.com> Signed-off-by:
-
Jakub Kicinski authored
Commit 7640ead9 ("bpf: verifier: make sure callees don't prune with caller differences") connected up parentage chains of all frames of the stack. It didn't, however, ensure propagate_liveness() propagates all liveness information along those chains. This means pruning happening in the callee may generate explored states with incomplete liveness for the chains in lower frames of the stack. The included selftest is similar to the prior one from commit 7640ead9 ("bpf: verifier: make sure callees don't prune with caller differences"), where callee would prune regardless of the difference in r8 state. Now we also initialize r9 to 0 or 1 based on a result from get_random(). r9 is never read so the walk with r9 = 0 gets pruned (correctly) after the walk with r9 = 1 completes. The selftest is so arranged that the pruning will happen in the callee. Since callee does not propagate read marks of r8, the explored state at the pruning point prior to the callee will now ignore r8. Propagate liveness on all frames of the stack when pruning. Fixes: f4d7e40a ("bpf: introduce function calls (verification)") Signed-off-by:
-
- 21 Mar, 2019 18 commits
-
-
Yunsheng Lin authored
When there is only one byte in a frag, the current calculation using "(size + HNS3_MAX_BD_SIZE - 1) >> HNS3_MAX_BD_SIZE_OFFSET" will return zero, because HNS3_MAX_BD_SIZE is 65535 and HNS3_MAX_BD_SIZE_OFFSET is 16. So it will cause tx error when a frag's size is one byte. This patch fixes it by using DIV_ROUND_UP. Fixes: 3fe13ed9 ("net: hns3: avoid mult + div op in critical data path") Signed-off-by:
Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by:
-
Herbert Xu authored
As it stands if a shrink is delayed because of an outstanding rehash, we will go into a rescheduling loop without ever doing the rehash. This patch fixes this by still carrying out the rehash and then rescheduling so that we can shrink after the completion of the rehash should it still be necessary. The return value of EEXIST captures this case and other cases (e.g., another thread expanded/rehashed the table at the same time) where we should still proceed with the rehash. Fixes: da20420f ("rhashtable: Add nested tables") Reported-by:
Josh Elsasser <jelsasser@appneta.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Tested-by:
-
Wang Hai authored
When registering struct net_device, it will call register_netdevice -> netdev_register_kobject -> device_initialize(dev); dev_set_name(dev, "%s", ndev->name) device_add(dev) register_queue_kobjects(ndev) In netdev_register_kobject(), if device_add(dev) or register_queue_kobjects(ndev) failed. Register_netdevice() will return error, causing netdev_freemem(ndev) to be called to free net_device, however put_device(&dev->dev)->..-> kobject_cleanup() won't be called, resulting in a memory leak. syzkaller report this: BUG: memory leak unreferenced object 0xffff8881f4fad168 (size 8): comm "syz-executor.0", pid 3575, jiffies 4294778002 (age 20.134s) hex dump (first 8 bytes): 77 70 61 6e 30 00 ff ff wpan0... backtrace: [<000000006d2d91d7>] kstrdup_const+0x3d/0x50 mm/util.c:73 [<00000000ba9ff953>] kvasprintf_const+0x112/0x170 lib/kasprintf.c:48 [<000000005555ec09>] kobject_set_name_vargs+0x55/0x130 lib/kobject.c:281 [<0000000098d28ec3>] dev_set_name+0xbb/0xf0 drivers/base/core.c:1915 [<00000000b7553017>] netdev_register_kobject+0xc0/0x410 net/core/net-sysfs.c:1727 [<00000000c826a797>] register_netdevice+0xa51/0xeb0 net/core/dev.c:8711 [<00000000857bfcfd>] cfg802154_update_iface_num.isra.2+0x13/0x90 [ieee802154] [<000000003126e453>] ieee802154_llsec_fill_key_id+0x1d5/0x570 [ieee802154] [<00000000e4b3df51>] 0xffffffffc1500e0e [<00000000b4319776>] platform_drv_probe+0xc6/0x180 drivers/base/platform.c:614 [<0000000037669347>] really_probe+0x491/0x7c0 drivers/base/dd.c:509 [<000000008fed8862>] driver_probe_device+0xdc/0x240 drivers/base/dd.c:671 [<00000000baf52041>] device_driver_attach+0xf2/0x130 drivers/base/dd.c:945 [<00000000c7cc8dec>] __driver_attach+0x10e/0x210 drivers/base/dd.c:1022 [<0000000057a757c2>] bus_for_each_dev+0x154/0x1e0 drivers/base/bus.c:304 [<000000005f5ae04b>] bus_add_driver+0x427/0x5e0 drivers/base/bus.c:645 Reported-by:
Hulk Robot <hulkci@huawei.com> Fixes: 1fa5ae85 ("driver core: get rid of struct device's bus_id string array") Signed-off-by:
Wang Hai <wanghai26@huawei.com> Reviewed-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by:
Stephen Hemminger <stephen@networkplumber.org> Signed-off-by:
-
David S. Miller authored
Davide Caratti says: ==================== net/sched: validate the control action with all the other parameters currently, the kernel checks for bad values of the control action in tcf_action_init_1(), after a successful call to the action's init() function. When the control action is 'goto chain', this causes two undesired behaviors: 1. "misconfigured action after replace that causes kernel crash": if users replace a valid TC action with another one having invalid control action, all the new configuration data (including the bad control action) are applied successfully, even if the kernel returned an error. As a consequence, it's possible to trigger a NULL pointer dereference in the traffic path of every TC action (1), replacing the control action with 'goto chain x', when chain <x> doesn't exist. 2. "refcount leak that makes kmemleak complain" when a valid 'goto chain' action is overwritten with another action, the kernel forgets to decrease refcounts in the chain. The above problems can be fixed if we validate the control action in each action's init() function, the same way as we are already doing for all the other configuration parameters. Now that chains can be released after an action is replaced, we need to care about concurrent access of 'goto_chain' pointer: ensure we access it through RCU, like we did with most action-specific configuration parameters. - Patch 1 removes the wrong checks and provides functions that can be used to properly validate control actions in individual actions - Patch 2 to 16 fix individual actions, and add TDC selftest code to verify the correct behavior (2) - Patch 17 and 18 fix concurrent access issues on 'goto_chain', that can be observed after the chain refcount leak is fixed. Changes since v1: - reword the cover letter - condense the extack message in case tc_action_check_ctrlact() is called with invalid parameters. - add tcf_action_set_ctrlact() to avoid code duplication an make the RCU-ification of 'goto_chain' easier. - fix errors in act_ife, act_simple, act_skbedit, and avoid useless 'goto end' in act_connmark, thanks a lot to Vlad Buslov. - avoid dereferencing 'goto_chain' in tcf_gact_goto_chain_index(), so we don't have to care about the grace period there. - let actions respect the grace period when they release chains, thanks to Cong Wang and Vlad Buslov. Changes since RFC: - include a fix for all TC actions - add a selftest for each TC action - squash fix for refcount leaks into a single patch, the first in the series, thanks to Cong Wang - ensure that chain refcount is released without tcfa_lock held, thanks to Vlad Buslov Notes: (1) act_ipt didn't need any fix, as the control action is constantly equal to TC_ACT_OK. (2) the selftest for act_simple fails because userspace tc backend for 'simple' does not parse the control action correctly (and hardcodes it to TC_ACT_PIPE). ==================== Signed-off-by: -
Davide Caratti authored
use RCU when accessing the action chain, to avoid use after free in the traffic path when 'goto chain' is replaced on existing TC actions (see script below). Since the control action is read in the traffic path without holding the action spinlock, we need to explicitly ensure that a->goto_chain is not NULL before dereferencing (i.e it's not sufficient to rely on the value of TC_ACT_GOTO_CHAIN bits). Not doing so caused NULL dereferences in tcf_action_goto_chain_exec() when the following script: # tc chain add dev dd0 chain 42 ingress protocol ip flower \ > ip_proto udp action pass index 4 # tc filter add dev dd0 ingress protocol ip flower \ > ip_proto udp action csum udp goto chain 42 index 66 # tc chain del dev dd0 chain 42 ingress (start UDP traffic towards dd0) # tc action replace action csum udp pass index 66 was run repeatedly for several hours. Suggested-by:
Vlad Buslov <vladbu@mellanox.com> Signed-off-by:
Davide Caratti <dcaratti@redhat.com> Signed-off-by:
-
Davide Caratti authored
callers of tcf_gact_goto_chain_index() can potentially read an old value of the chain index, or even dereference a NULL 'goto_chain' pointer, because 'goto_chain' and 'tcfa_action' are read in the traffic path without caring of concurrent write in the control path. The most recent value of chain index can be read also from a->tcfa_action (it's encoded there together with TC_ACT_GOTO_CHAIN bits), so we don't really need to dereference 'goto_chain': just read the chain id from the control action. Fixes: e457d86a ("net: sched: add couple of goto_chain helpers") Signed-off-by:
-
Davide Caratti authored
the following script: # tc qdisc add dev crash0 clsact # tc filter add dev crash0 egress matchall \ > action vlan pop pass index 90 # tc actions replace action vlan \ > pop goto chain 42 index 90 cookie c1a0c1a0 # tc actions show action vlan had the following output: Error: Failed to init TC action chain. We have an error talking to the kernel total acts 1 action order 0: vlan pop goto chain 42 index 90 ref 2 bind 1 cookie c1a0c1a0 Then, the first packet transmitted by crash0 made the kernel crash: BUG: unable to handle kernel NULL pointer dereference at 0000000000000000 #PF error: [normal kernel read fault] PGD 800000007974f067 P4D 800000007974f067 PUD 79638067 PMD 0 Oops: 0000 [#1] SMP PTI CPU: 3 PID: 0 Comm: swapper/3 Not tainted 5.0.0-rc4.gotochain_crash+ #536 Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011 RIP: 0010:tcf_action_exec+0xb8/0x100 Code: 00 00 00 20 74 1d 83 f8 03 75 09 49 83 c4 08 4d 39 ec 75 bc 48 83 c4 10 5b 5d 41 5c 41 5d 41 5e 41 5f c3 49 8b 97 a8 00 00 00 <48> 8b 12 48 89 55 00 48 83 c4 10 5b 5d 41 5c 41 5d 41 5e 41 5f c3 RSP: 0018:ffff982dfdb83be0 EFLAGS: 00010246 RAX: 000000002000002a RBX: ffff982dfc55db00 RCX: 0000000000000000 RDX: 0000000000000000 RSI: ffff982df97099c0 RDI: ffff982dfc55db00 RBP: ffff982dfdb83c80 R08: ffff982df983fec8 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: ffff982df5aacd00 R13: ffff982df5aacd08 R14: 0000000000000001 R15: ffff982df97099c0 FS: 0000000000000000(0000) GS:ffff982dfdb80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 00000000796d0005 CR4: 00000000001606e0 Call Trace: <IRQ> tcf_classify+0x58/0x120 __dev_queue_xmit+0x40a/0x890 ? ip6_finish_output2+0x369/0x590 ip6_finish_output2+0x369/0x590 ? ip6_output+0x68/0x110 ip6_output+0x68/0x110 ? nf_hook.constprop.35+0x79/0xc0 mld_sendpack+0x16f/0x220 mld_ifc_timer_expire+0x195/0x2c0 ? igmp6_timer_handler+0x70/0x70 call_timer_fn+0x2b/0x130 run_timer_softirq+0x3e8/0x440 ? enqueue_hrtimer+0x39/0x90 __do_softirq+0xe3/0x2f5 irq_exit+0xf0/0x100 smp_apic_timer_interrupt+0x6c/0x130 apic_timer_interrupt+0xf/0x20 </IRQ> RIP: 0010:native_safe_halt+0x2/0x10 Code: 7b ff ff ff 7f f3 c3 65 48 8b 04 25 00 5c 01 00 f0 80 48 02 20 48 8b 00 a8 08 74 8b eb c1 90 90 90 90 90 90 90 90 90 90 fb f4 <c3> 0f 1f 00 66 2e 0f 1f 84 00 00 00 00 00 f4 c3 90 90 90 90 90 90 RSP: 0018:ffffa4714038feb8 EFLAGS: 00000246 ORIG_RAX: ffffffffffffff13 RAX: ffffffff840184f0 RBX: 0000000000000003 RCX: 0000000000000000 RDX: 0000000000000001 RSI: 0000000000000000 RDI: 0000001e57d3f387 RBP: 0000000000000003 R08: 001125d9ca39e1eb R09: 0000000000000000 R10: 000000000000027d R11: 000000000009f400 R12: 0000000000000000 R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 ? __sched_text_end+0x1/0x1 default_idle+0x1c/0x140 do_idle+0x1c4/0x280 cpu_startup_entry+0x19/0x20 start_secondary+0x1a7/0x200 secondary_startup_64+0xa4/0xb0 Modules linked in: act_vlan veth ip6table_filter ip6_tables iptable_filter binfmt_misc ext4 snd_hda_codec_generic mbcache crct10dif_pclmul jbd2 snd_hda_intel crc32_pclmul snd_hda_codec ghash_clmulni_intel snd_hwdep snd_hda_core snd_seq snd_seq_device snd_pcm aesni_intel crypto_simd cryptd glue_helper joydev snd_timer virtio_balloon snd pcspkr soundcore i2c_piix4 nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs ata_generic pata_acpi qxl drm_kms_helper syscopyarea sysfillrect sysimgblt virtio_net fb_sys_fops virtio_blk ttm net_failover virtio_console failover ata_piix drm libata crc32c_intel virtio_pci serio_raw virtio_ring virtio floppy dm_mirror dm_region_hash dm_log dm_mod CR2: 0000000000000000 Validating the control action within tcf_vlan_init() proved to fix the above issue. A TDC selftest is added to verify the correct behavior. Fixes: db50514f ("net: sched: add termination action to allow goto chain") Fixes: 97763dc0 ("net_sched: reject unknown tcfa_action values") Signed-off-by: -
Davide Caratti authored
the following script: # tc qdisc add dev crash0 clsact # tc filter add dev crash0 egress matchall \ > action tunnel_key set src_ip 10.10.10.1 dst_ip 20.20.2 dst_port 3128 \ > nocsum id 1 pass index 90 # tc actions replace action tunnel_key \ > set src_ip 10.10.10.1 dst_ip 20.20.2 dst_port 3128 nocsum id 1 \ > goto chain 42 index 90 cookie c1a0c1a0 # tc actions show action tunnel_key had the following output: Error: Failed to init TC action chain. We have an error talking to the kernel total acts 1 action order 0: tunnel_key set src_ip 10.10.10.1 dst_ip 20.20.2.0 key_id 1 dst_port 3128 nocsum goto chain 42 index 90 ref 2 bind 1 cookie c1a0c1a0 then, the first packet transmitted by crash0 made the kernel crash: BUG: unable to handle kernel NULL pointer dereference at 0000000000000000 #PF error: [normal kernel read fault] PGD 800000002aba4067 P4D 800000002aba4067 PUD 795f9067 PMD 0 Oops: 0000 [#1] SMP PTI CPU: 3 PID: 0 Comm: swapper/3 Not tainted 5.0.0-rc4.gotochain_crash+ #536 Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011 RIP: 0010:tcf_action_exec+0xb8/0x100 Code: 00 00 00 20 74 1d 83 f8 03 75 09 49 83 c4 08 4d 39 ec 75 bc 48 83 c4 10 5b 5d 41 5c 41 5d 41 5e 41 5f c3 49 8b 97 a8 00 00 00 <48> 8b 12 48 89 55 00 48 83 c4 10 5b 5d 41 5c 41 5d 41 5e 41 5f c3 RSP: 0018:ffff9346bdb83be0 EFLAGS: 00010246 RAX: 000000002000002a RBX: ffff9346bb795c00 RCX: 0000000000000002 RDX: 0000000000000000 RSI: ffff93466c881700 RDI: 0000000000000246 RBP: ffff9346bdb83c80 R08: ffff9346b3e1e0c8 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: ffff9346b978f000 R13: ffff9346b978f008 R14: 0000000000000001 R15: ffff93466dceeb40 FS: 0000000000000000(0000) GS:ffff9346bdb80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 000000007a6c2002 CR4: 00000000001606e0 Call Trace: <IRQ> tcf_classify+0x58/0x120 __dev_queue_xmit+0x40a/0x890 ? ip6_finish_output2+0x369/0x590 ip6_finish_output2+0x369/0x590 ? ip6_output+0x68/0x110 ip6_output+0x68/0x110 ? nf_hook.constprop.35+0x79/0xc0 mld_sendpack+0x16f/0x220 mld_ifc_timer_expire+0x195/0x2c0 ? igmp6_timer_handler+0x70/0x70 call_timer_fn+0x2b/0x130 run_timer_softirq+0x3e8/0x440 ? tick_sched_timer+0x37/0x70 __do_softirq+0xe3/0x2f5 irq_exit+0xf0/0x100 smp_apic_timer_interrupt+0x6c/0x130 apic_timer_interrupt+0xf/0x20 </IRQ> RIP: 0010:native_safe_halt+0x2/0x10 Code: 55 ff ff ff 7f f3 c3 65 48 8b 04 25 00 5c 01 00 f0 80 48 02 20 48 8b 00 a8 08 74 8b eb c1 90 90 90 90 90 90 90 90 90 90 fb f4 <c3> 0f 1f 00 66 2e 0f 1f 84 00 00 00 00 00 f4 c3 90 90 90 90 90 90 RSP: 0018:ffffa48a8038feb8 EFLAGS: 00000246 ORIG_RAX: ffffffffffffff13 RAX: ffffffffaa8184f0 RBX: 0000000000000003 RCX: 0000000000000000 RDX: 0000000000000001 RSI: 0000000000000087 RDI: 0000000000000003 RBP: 0000000000000003 R08: 0011251c6fcfac49 R09: ffff9346b995be00 R10: ffffa48a805e7ce8 R11: 00000000024c38dd R12: 0000000000000000 R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 ? __sched_text_end+0x1/0x1 default_idle+0x1c/0x140 do_idle+0x1c4/0x280 cpu_startup_entry+0x19/0x20 start_secondary+0x1a7/0x200 secondary_startup_64+0xa4/0xb0 Modules linked in: act_tunnel_key veth ip6table_filter ip6_tables iptable_filter binfmt_misc ext4 crct10dif_pclmul crc32_pclmul snd_hda_codec_generic ghash_clmulni_intel mbcache snd_hda_intel jbd2 snd_hda_codec snd_hwdep snd_hda_core snd_seq snd_seq_device snd_pcm aesni_intel crypto_simd cryptd glue_helper joydev snd_timer snd pcspkr virtio_balloon soundcore i2c_piix4 nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs ata_generic pata_acpi qxl drm_kms_helper syscopyarea sysfillrect virtio_net sysimgblt fb_sys_fops ttm net_failover virtio_console virtio_blk failover drm serio_raw crc32c_intel ata_piix virtio_pci floppy virtio_ring libata virtio dm_mirror dm_region_hash dm_log dm_mod CR2: 0000000000000000 Validating the control action within tcf_tunnel_key_init() proved to fix the above issue. A TDC selftest is added to verify the correct behavior. Fixes: db50514f ("net: sched: add termination action to allow goto chain") Fixes: 97763dc0 ("net_sched: reject unknown tcfa_action values") Signed-off-by: -
Davide Caratti authored
the following script: # tc qdisc add dev crash0 clsact # tc filter add dev crash0 egress matchall \ > action skbmod set smac 00:c1:a0:c1:a0:00 pass index 90 # tc actions replace action skbmod \ > set smac 00:c1:a0:c1:a0:00 goto chain 42 index 90 cookie c1a0c1a0 # tc actions show action skbmod had the following output: src MAC address <00:c1:a0:c1:a0:00> src MAC address <00:c1:a0:c1:a0:00> Error: Failed to init TC action chain. We have an error talking to the kernel total acts 1 action order 0: skbmod goto chain 42 set smac 00:c1:a0:c1:a0:00 index 90 ref 2 bind 1 cookie c1a0c1a0 Then, the first packet transmitted by crash0 made the kernel crash: BUG: unable to handle kernel NULL pointer dereference at 0000000000000000 #PF error: [normal kernel read fault] PGD 800000002d5c7067 P4D 800000002d5c7067 PUD 77e16067 PMD 0 Oops: 0000 [#1] SMP PTI CPU: 3 PID: 0 Comm: swapper/3 Not tainted 5.0.0-rc4.gotochain_crash+ #536 Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011 RIP: 0010:tcf_action_exec+0xb8/0x100 Code: 00 00 00 20 74 1d 83 f8 03 75 09 49 83 c4 08 4d 39 ec 75 bc 48 83 c4 10 5b 5d 41 5c 41 5d 41 5e 41 5f c3 49 8b 97 a8 00 00 00 <48> 8b 12 48 89 55 00 48 83 c4 10 5b 5d 41 5c 41 5d 41 5e 41 5f c3 RSP: 0018:ffff8987ffd83be0 EFLAGS: 00010246 RAX: 000000002000002a RBX: ffff8987aeb68800 RCX: ffff8987fa263640 RDX: 0000000000000000 RSI: ffff8987f51c8802 RDI: 00000000000000a0 RBP: ffff8987ffd83c80 R08: ffff8987f939bac8 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: ffff8987f5c77d00 R13: ffff8987f5c77d08 R14: 0000000000000001 R15: ffff8987f0c29f00 FS: 0000000000000000(0000) GS:ffff8987ffd80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 000000007832c004 CR4: 00000000001606e0 Call Trace: <IRQ> tcf_classify+0x58/0x120 __dev_queue_xmit+0x40a/0x890 ? ip6_finish_output2+0x369/0x590 ip6_finish_output2+0x369/0x590 ? ip6_output+0x68/0x110 ip6_output+0x68/0x110 ? nf_hook.constprop.35+0x79/0xc0 mld_sendpack+0x16f/0x220 mld_ifc_timer_expire+0x195/0x2c0 ? igmp6_timer_handler+0x70/0x70 call_timer_fn+0x2b/0x130 run_timer_softirq+0x3e8/0x440 ? tick_sched_timer+0x37/0x70 __do_softirq+0xe3/0x2f5 irq_exit+0xf0/0x100 smp_apic_timer_interrupt+0x6c/0x130 apic_timer_interrupt+0xf/0x20 </IRQ> RIP: 0010:native_safe_halt+0x2/0x10 Code: 56 ff ff ff 7f f3 c3 65 48 8b 04 25 00 5c 01 00 f0 80 48 02 20 48 8b 00 a8 08 74 8b eb c1 90 90 90 90 90 90 90 90 90 90 fb f4 <c3> 0f 1f 00 66 2e 0f 1f 84 00 00 00 00 00 f4 c3 90 90 90 90 90 90 RSP: 0018:ffffa2a1c038feb8 EFLAGS: 00000246 ORIG_RAX: ffffffffffffff13 RAX: ffffffffa94184f0 RBX: 0000000000000003 RCX: 0000000000000001 RDX: 0000000000000001 RSI: 0000000000000087 RDI: 0000000000000003 RBP: 0000000000000003 R08: 001123cfc2ba71ac R09: 0000000000000000 R10: 0000000000000000 R11: 00000000000f4240 R12: 0000000000000000 R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 ? __sched_text_end+0x1/0x1 default_idle+0x1c/0x140 do_idle+0x1c4/0x280 cpu_startup_entry+0x19/0x20 start_secondary+0x1a7/0x200 secondary_startup_64+0xa4/0xb0 Modules linked in: act_skbmod veth ip6table_filter ip6_tables iptable_filter binfmt_misc ext4 crct10dif_pclmul crc32_pclmul ghash_clmulni_intel mbcache jbd2 snd_hda_codec_generic snd_hda_intel snd_hda_codec snd_hwdep snd_hda_core snd_seq snd_seq_device aesni_intel crypto_simd cryptd glue_helper snd_pcm joydev pcspkr virtio_balloon snd_timer snd i2c_piix4 soundcore nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs ata_generic pata_acpi qxl drm_kms_helper syscopyarea sysfillrect virtio_net sysimgblt fb_sys_fops net_failover virtio_console ttm virtio_blk failover drm crc32c_intel serio_raw ata_piix virtio_pci libata virtio_ring virtio floppy dm_mirror dm_region_hash dm_log dm_mod CR2: 0000000000000000 Validating the control action within tcf_skbmod_init() proved to fix the above issue. A TDC selftest is added to verify the correct behavior. Fixes: db50514f ("net: sched: add termination action to allow goto chain") Fixes: 97763dc0 ("net_sched: reject unknown tcfa_action values") Signed-off-by: -
Davide Caratti authored
the following script: # tc qdisc add dev crash0 clsact # tc filter add dev crash0 egress matchall \ > action skbedit ptype host pass index 90 # tc actions replace action skbedit \ > ptype host goto chain 42 index 90 cookie c1a0c1a0 # tc actions show action skbedit had the following output: Error: Failed to init TC action chain. We have an error talking to the kernel total acts 1 action order 0: skbedit ptype host goto chain 42 index 90 ref 2 bind 1 cookie c1a0c1a0 Then, the first packet transmitted by crash0 made the kernel crash: BUG: unable to handle kernel NULL pointer dereference at 0000000000000000 #PF error: [normal kernel read fault] PGD 0 P4D 0 Oops: 0000 [#1] SMP PTI CPU: 3 PID: 3467 Comm: kworker/3:3 Not tainted 5.0.0-rc4.gotochain_crash+ #536 Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011 Workqueue: ipv6_addrconf addrconf_dad_work RIP: 0010:tcf_action_exec+0xb8/0x100 Code: 00 00 00 20 74 1d 83 f8 03 75 09 49 83 c4 08 4d 39 ec 75 bc 48 83 c4 10 5b 5d 41 5c 41 5d 41 5e 41 5f c3 49 8b 97 a8 00 00 00 <48> 8b 12 48 89 55 00 48 83 c4 10 5b 5d 41 5c 41 5d 41 5e 41 5f c3 RSP: 0018:ffffb50a81e1fad0 EFLAGS: 00010246 RAX: 000000002000002a RBX: ffff9aa47ba4ea00 RCX: 0000000000000001 RDX: 0000000000000000 RSI: ffff9aa469eeb3c0 RDI: ffff9aa47ba4ea00 RBP: ffffb50a81e1fb70 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: ffff9aa47bce0638 R12: ffff9aa4793b0c00 R13: ffff9aa4793b0c08 R14: 0000000000000001 R15: ffff9aa469eeb3c0 FS: 0000000000000000(0000) GS:ffff9aa474780000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 000000007360e005 CR4: 00000000001606e0 Call Trace: tcf_classify+0x58/0x120 __dev_queue_xmit+0x40a/0x890 ? ndisc_next_option+0x50/0x50 ? ___neigh_create+0x4d5/0x680 ? ip6_finish_output2+0x1b5/0x590 ip6_finish_output2+0x1b5/0x590 ? ip6_output+0x68/0x110 ip6_output+0x68/0x110 ? nf_hook.constprop.28+0x79/0xc0 ndisc_send_skb+0x248/0x2e0 ndisc_send_ns+0xf8/0x200 ? addrconf_dad_work+0x389/0x4b0 addrconf_dad_work+0x389/0x4b0 ? __switch_to_asm+0x34/0x70 ? process_one_work+0x195/0x380 ? addrconf_dad_completed+0x370/0x370 process_one_work+0x195/0x380 worker_thread+0x30/0x390 ? process_one_work+0x380/0x380 kthread+0x113/0x130 ? kthread_park+0x90/0x90 ret_from_fork+0x35/0x40 Modules linked in: act_skbedit veth ip6table_filter ip6_tables iptable_filter binfmt_misc crct10dif_pclmul crc32_pclmul ghash_clmulni_intel ext4 snd_hda_codec_generic snd_hda_intel snd_hda_codec snd_hwdep mbcache snd_hda_core jbd2 snd_seq snd_seq_device snd_pcm aesni_intel crypto_simd cryptd snd_timer glue_helper snd joydev soundcore pcspkr virtio_balloon i2c_piix4 nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs ata_generic pata_acpi qxl drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ttm virtio_net net_failover drm failover virtio_blk virtio_console ata_piix virtio_pci crc32c_intel serio_raw libata virtio_ring virtio floppy dm_mirror dm_region_hash dm_log dm_mod CR2: 0000000000000000 Validating the control action within tcf_skbedit_init() proved to fix the above issue. A TDC selftest is added to verify the correct behavior. Fixes: db50514f ("net: sched: add termination action to allow goto chain") Fixes: 97763dc0 ("net_sched: reject unknown tcfa_action values") Signed-off-by: -
Davide Caratti authored
the following script: # tc qdisc add dev crash0 clsact # tc filter add dev crash0 egress matchall \ > action simple sdata hello pass index 90 # tc actions replace action simple \ > sdata world goto chain 42 index 90 cookie c1a0c1a0 # tc action show action simple had the following output: Error: Failed to init TC action chain. We have an error talking to the kernel total acts 1 action order 0: Simple <world> index 90 ref 2 bind 1 cookie c1a0c1a0 Then, the first packet transmitted by crash0 made the kernel crash: BUG: unable to handle kernel NULL pointer dereference at 0000000000000000 #PF error: [normal kernel read fault] PGD 800000006a6fb067 P4D 800000006a6fb067 PUD 6aed6067 PMD 0 Oops: 0000 [#1] SMP PTI CPU: 2 PID: 3241 Comm: kworker/2:0 Not tainted 5.0.0-rc4.gotochain_crash+ #536 Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011 Workqueue: ipv6_addrconf addrconf_dad_work RIP: 0010:tcf_action_exec+0xb8/0x100 Code: 00 00 00 20 74 1d 83 f8 03 75 09 49 83 c4 08 4d 39 ec 75 bc 48 83 c4 10 5b 5d 41 5c 41 5d 41 5e 41 5f c3 49 8b 97 a8 00 00 00 <48> 8b 12 48 89 55 00 48 83 c4 10 5b 5d 41 5c 41 5d 41 5e 41 5f c3 RSP: 0018:ffffbe6781763ad0 EFLAGS: 00010246 RAX: 000000002000002a RBX: ffff9e59bdb80e00 RCX: 0000000000000000 RDX: 0000000000000000 RSI: ffff9e59b4716738 RDI: ffff9e59ab12d140 RBP: ffffbe6781763b70 R08: 0000000000000234 R09: 0000000000aaaaaa R10: 0000000000000000 R11: ffff9e59b247cd50 R12: ffff9e59b112f100 R13: ffff9e59b112f108 R14: 0000000000000001 R15: ffff9e59ab12d0c0 FS: 0000000000000000(0000) GS:ffff9e59b4700000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 000000006af92004 CR4: 00000000001606e0 Call Trace: tcf_classify+0x58/0x120 __dev_queue_xmit+0x40a/0x890 ? ndisc_next_option+0x50/0x50 ? ___neigh_create+0x4d5/0x680 ? ip6_finish_output2+0x1b5/0x590 ip6_finish_output2+0x1b5/0x590 ? ip6_output+0x68/0x110 ip6_output+0x68/0x110 ? nf_hook.constprop.28+0x79/0xc0 ndisc_send_skb+0x248/0x2e0 ndisc_send_ns+0xf8/0x200 ? addrconf_dad_work+0x389/0x4b0 addrconf_dad_work+0x389/0x4b0 ? __switch_to_asm+0x34/0x70 ? process_one_work+0x195/0x380 ? addrconf_dad_completed+0x370/0x370 process_one_work+0x195/0x380 worker_thread+0x30/0x390 ? process_one_work+0x380/0x380 kthread+0x113/0x130 ? kthread_park+0x90/0x90 ret_from_fork+0x35/0x40 Modules linked in: act_simple veth ip6table_filter ip6_tables iptable_filter binfmt_misc crct10dif_pclmul crc32_pclmul ghash_clmulni_intel ext4 snd_hda_codec_generic snd_hda_intel snd_hda_codec snd_hwdep mbcache snd_hda_core jbd2 snd_seq snd_seq_device snd_pcm aesni_intel crypto_simd cryptd snd_timer glue_helper snd joydev virtio_balloon pcspkr soundcore i2c_piix4 nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs ata_generic pata_acpi qxl drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops virtio_net ttm net_failover virtio_console virtio_blk failover drm crc32c_intel serio_raw floppy ata_piix libata virtio_pci virtio_ring virtio dm_mirror dm_region_hash dm_log dm_mod CR2: 0000000000000000 Validating the control action within tcf_simple_init() proved to fix the above issue. A TDC selftest is added to verify the correct behavior. Fixes: db50514f ("net: sched: add termination action to allow goto chain") Fixes: 97763dc0 ("net_sched: reject unknown tcfa_action values") Signed-off-by: -
Davide Caratti authored
the following script: # tc qdisc add dev crash0 clsact # tc filter add dev crash0 egress matchall \ > action sample rate 1024 group 4 pass index 90 # tc actions replace action sample \ > rate 1024 group 4 goto chain 42 index 90 cookie c1a0c1a0 # tc actions show action sample had the following output: Error: Failed to init TC action chain. We have an error talking to the kernel total acts 1 action order 0: sample rate 1/1024 group 4 goto chain 42 index 90 ref 2 bind 1 cookie c1a0c1a0 Then, the first packet transmitted by crash0 made the kernel crash: BUG: unable to handle kernel NULL pointer dereference at 0000000000000000 #PF error: [normal kernel read fault] PGD 8000000079966067 P4D 8000000079966067 PUD 7987b067 PMD 0 Oops: 0000 [#1] SMP PTI CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.0.0-rc4.gotochain_crash+ #536 Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011 Workqueue: ipv6_addrconf addrconf_dad_work RIP: 0010:tcf_action_exec+0xb8/0x100 Code: 00 00 00 20 74 1d 83 f8 03 75 09 49 83 c4 08 4d 39 ec 75 bc 48 83 c4 10 5b 5d 41 5c 41 5d 41 5e 41 5f c3 49 8b 97 a8 00 00 00 <48> 8b 12 48 89 55 00 48 83 c4 10 5b 5d 41 5c 41 5d 41 5e 41 5f c3 RSP: 0018:ffffbee60033fad0 EFLAGS: 00010246 RAX: 000000002000002a RBX: ffff99d7ae6e3b00 RCX: 00000000e555df9b RDX: 0000000000000000 RSI: 00000000b0352718 RDI: ffff99d7fda1fcf0 RBP: ffffbee60033fb70 R08: 0000000070731ab1 R09: 0000000000000400 R10: 0000000000000000 R11: ffff99d7ac733838 R12: ffff99d7f3c2be00 R13: ffff99d7f3c2be08 R14: 0000000000000001 R15: ffff99d7f3c2b600 FS: 0000000000000000(0000) GS:ffff99d7fda00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 00000000797de006 CR4: 00000000001606f0 Call Trace: tcf_classify+0x58/0x120 __dev_queue_xmit+0x40a/0x890 ? ndisc_next_option+0x50/0x50 ? ___neigh_create+0x4d5/0x680 ? ip6_finish_output2+0x1b5/0x590 ip6_finish_output2+0x1b5/0x590 ? ip6_output+0x68/0x110 ip6_output+0x68/0x110 ? nf_hook.constprop.28+0x79/0xc0 ndisc_send_skb+0x248/0x2e0 ndisc_send_ns+0xf8/0x200 ? addrconf_dad_work+0x389/0x4b0 addrconf_dad_work+0x389/0x4b0 ? __switch_to_asm+0x34/0x70 ? process_one_work+0x195/0x380 ? addrconf_dad_completed+0x370/0x370 process_one_work+0x195/0x380 worker_thread+0x30/0x390 ? process_one_work+0x380/0x380 kthread+0x113/0x130 ? kthread_park+0x90/0x90 ret_from_fork+0x35/0x40 Modules linked in: act_sample psample veth ip6table_filter ip6_tables iptable_filter binfmt_misc ext4 crct10dif_pclmul crc32_pclmul ghash_clmulni_intel mbcache jbd2 snd_hda_codec_generic snd_hda_intel snd_hda_codec snd_hwdep snd_hda_core snd_seq snd_seq_device aesni_intel crypto_simd snd_pcm cryptd glue_helper snd_timer joydev snd pcspkr virtio_balloon i2c_piix4 soundcore nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs ata_generic pata_acpi qxl drm_kms_helper syscopyarea sysfillrect virtio_net sysimgblt fb_sys_fops net_failover ttm failover virtio_blk virtio_console drm ata_piix serio_raw crc32c_intel libata virtio_pci virtio_ring virtio floppy dm_mirror dm_region_hash dm_log dm_mod CR2: 0000000000000000 Validating the control action within tcf_sample_init() proved to fix the above issue. A TDC selftest is added to verify the correct behavior. Fixes: db50514f ("net: sched: add termination action to allow goto chain") Fixes: 97763dc0 ("net_sched: reject unknown tcfa_action values") Signed-off-by: -
Davide Caratti authored
the following script: # tc qdisc add dev crash0 clsact # tc filter add dev crash0 egress matchall \ > action police rate 3mbit burst 250k pass index 90 # tc actions replace action police \ > rate 3mbit burst 250k goto chain 42 index 90 cookie c1a0c1a0 # tc actions show action police rate 3mbit burst had the following output: Error: Failed to init TC action chain. We have an error talking to the kernel total acts 1 action order 0: police 0x5a rate 3Mbit burst 250Kb mtu 2Kb action goto chain 42 overhead 0b ref 2 bind 1 cookie c1a0c1a0 Then, when crash0 starts transmitting more than 3Mbit/s, the following kernel crash is observed: BUG: unable to handle kernel NULL pointer dereference at 0000000000000000 #PF error: [normal kernel read fault] PGD 800000007a779067 P4D 800000007a779067 PUD 2ad96067 PMD 0 Oops: 0000 [#1] SMP PTI CPU: 3 PID: 5032 Comm: netperf Not tainted 5.0.0-rc4.gotochain_crash+ #533 Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011 RIP: 0010:tcf_action_exec+0xb8/0x100 Code: 00 00 00 20 74 1d 83 f8 03 75 09 49 83 c4 08 4d 39 ec 75 bc 48 83 c4 10 5b 5d 41 5c 41 5d 41 5e 41 5f c3 49 8b 97 a8 00 00 00 <48> 8b 12 48 89 55 00 48 83 c4 10 5b 5d 41 5c 41 5d 41 5e 41 5f c3 RSP: 0018:ffffb0e04064fa60 EFLAGS: 00010246 RAX: 000000002000002a RBX: ffff93bb3322cce0 RCX: 0000000000000005 RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff93bb3322cce0 RBP: ffffb0e04064fb00 R08: 0000000000000022 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000001 R12: ffff93bb3beed300 R13: ffff93bb3beed308 R14: 0000000000000001 R15: ffff93bb3b64d000 FS: 00007f0bc6be5740(0000) GS:ffff93bb3db80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 00000000746a8001 CR4: 00000000001606e0 Call Trace: tcf_classify+0x58/0x120 __dev_queue_xmit+0x40a/0x890 ? ipt_do_table+0x31c/0x420 [ip_tables] ? ip_finish_output2+0x16f/0x430 ip_finish_output2+0x16f/0x430 ? ip_output+0x69/0xe0 ip_output+0x69/0xe0 ? ip_forward_options+0x1a0/0x1a0 __tcp_transmit_skb+0x563/0xa40 tcp_write_xmit+0x243/0xfa0 __tcp_push_pending_frames+0x32/0xf0 tcp_sendmsg_locked+0x404/0xd30 tcp_sendmsg+0x27/0x40 sock_sendmsg+0x36/0x40 __sys_sendto+0x10e/0x140 ? __sys_connect+0x87/0xf0 ? syscall_trace_enter+0x1df/0x2e0 ? __audit_syscall_exit+0x216/0x260 __x64_sys_sendto+0x24/0x30 do_syscall_64+0x5b/0x180 entry_SYSCALL_64_after_hwframe+0x44/0xa9 RIP: 0033:0x7f0bc5ffbafd Code: 89 01 48 83 c8 ff c3 66 0f 1f 44 00 00 8b 05 ae c4 2c 00 85 c0 75 2d 45 31 c9 45 31 c0 4c 63 d1 48 63 ff b8 2c 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 01 c3 48 8b 15 63 63 2c 00 f7 d8 64 89 02 48 RSP: 002b:00007fffef94b7f8 EFLAGS: 00000246 ORIG_RAX: 000000000000002c RAX: ffffffffffffffda RBX: 0000000000004000 RCX: 00007f0bc5ffbafd RDX: 0000000000004000 RSI: 00000000017e5420 RDI: 0000000000000004 RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000004 R13: 00000000017e51d0 R14: 0000000000000010 R15: 0000000000000006 Modules linked in: act_police veth ip6table_filter ip6_tables iptable_filter binfmt_misc ext4 snd_hda_codec_generic mbcache crct10dif_pclmul jbd2 crc32_pclmul ghash_clmulni_intel snd_hda_intel snd_hda_codec snd_hwdep snd_hda_core snd_seq snd_seq_device snd_pcm aesni_intel crypto_simd cryptd glue_helper snd_timer snd joydev pcspkr virtio_balloon soundcore i2c_piix4 nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs ata_generic pata_acpi qxl drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ttm drm virtio_blk virtio_net virtio_console net_failover failover crc32c_intel ata_piix libata serio_raw virtio_pci virtio_ring virtio floppy dm_mirror dm_region_hash dm_log dm_mod CR2: 0000000000000000 Validating the control action within tcf_police_init() proved to fix the above issue. A TDC selftest is added to verify the correct behavior. Fixes: db50514f ("net: sched: add termination action to allow goto chain") Fixes: 97763dc0 ("net_sched: reject unknown tcfa_action values") Signed-off-by: -
Davide Caratti authored
the following script: # tc filter add dev crash0 egress matchall \ > action pedit ex munge ip ttl set 10 pass index 90 # tc actions replace action pedit \ > ex munge ip ttl set 10 goto chain 42 index 90 cookie c1a0c1a0 # tc actions show action pedit had the following output: Error: Failed to init TC action chain. We have an error talking to the kernel total acts 1 action order 0: pedit action goto chain 42 keys 1 index 90 ref 2 bind 1 key #0 at ipv4+8: val 0a000000 mask 00ffffff cookie c1a0c1a0 Then, the first packet transmitted by crash0 made the kernel crash: BUG: unable to handle kernel NULL pointer dereference at 0000000000000000 #PF error: [normal kernel read fault] PGD 0 P4D 0 Oops: 0000 [#1] SMP PTI CPU: 2 PID: 0 Comm: swapper/2 Not tainted 5.0.0-rc4.gotochain_crash+ #533 Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011 RIP: 0010:tcf_action_exec+0xb8/0x100 Code: 00 00 00 20 74 1d 83 f8 03 75 09 49 83 c4 08 4d 39 ec 75 bc 48 83 c4 10 5b 5d 41 5c 41 5d 41 5e 41 5f c3 49 8b 97 a8 00 00 00 <48> 8b 12 48 89 55 00 48 83 c4 10 5b 5d 41 5c 41 5d 41 5e 41 5f c3 RSP: 0018:ffff94a73db03be0 EFLAGS: 00010246 RAX: 000000002000002a RBX: ffff94a6ee4c0700 RCX: 000000000000000a RDX: 0000000000000000 RSI: ffff94a6ed22c800 RDI: 0000000000000000 RBP: ffff94a73db03c80 R08: ffff94a7386fa4c8 R09: ffff94a73229ea20 R10: 0000000000000000 R11: 0000000000000000 R12: ffff94a6ed22cb00 R13: ffff94a6ed22cb08 R14: 0000000000000001 R15: ffff94a6ed22c800 FS: 0000000000000000(0000) GS:ffff94a73db00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 000000007120e002 CR4: 00000000001606e0 Call Trace: <IRQ> tcf_classify+0x58/0x120 __dev_queue_xmit+0x40a/0x890 ? ip6_finish_output2+0x369/0x590 ip6_finish_output2+0x369/0x590 ? ip6_output+0x68/0x110 ip6_output+0x68/0x110 ? nf_hook.constprop.35+0x79/0xc0 mld_sendpack+0x16f/0x220 mld_ifc_timer_expire+0x195/0x2c0 ? igmp6_timer_handler+0x70/0x70 call_timer_fn+0x2b/0x130 run_timer_softirq+0x3e8/0x440 ? tick_sched_timer+0x37/0x70 __do_softirq+0xe3/0x2f5 irq_exit+0xf0/0x100 smp_apic_timer_interrupt+0x6c/0x130 apic_timer_interrupt+0xf/0x20 </IRQ> RIP: 0010:native_safe_halt+0x2/0x10 Code: 4e ff ff ff 7f f3 c3 65 48 8b 04 25 00 5c 01 00 f0 80 48 02 20 48 8b 00 a8 08 74 8b eb c1 90 90 90 90 90 90 90 90 90 90 fb f4 <c3> 0f 1f 00 66 2e 0f 1f 84 00 00 00 00 00 f4 c3 90 90 90 90 90 90 RSP: 0018:ffffab1740387eb8 EFLAGS: 00000246 ORIG_RAX: ffffffffffffff13 RAX: ffffffffb18184f0 RBX: 0000000000000002 RCX: 0000000000000001 RDX: 0000000000000001 RSI: 0000000000000087 RDI: 0000000000000002 RBP: 0000000000000002 R08: 000f168fa695f9a9 R09: 0000000000000020 R10: 0000000000000004 R11: 0000000000000000 R12: 0000000000000000 R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 ? __sched_text_end+0x1/0x1 default_idle+0x1c/0x140 do_idle+0x1c4/0x280 cpu_startup_entry+0x19/0x20 start_secondary+0x1a7/0x200 secondary_startup_64+0xa4/0xb0 Modules linked in: act_pedit veth ip6table_filter ip6_tables iptable_filter binfmt_misc ext4 mbcache jbd2 crct10dif_pclmul crc32_pclmul ghash_clmulni_intel snd_hda_codec_generic snd_hda_intel snd_hda_codec snd_hwdep aesni_intel snd_hda_core crypto_simd snd_seq cryptd glue_helper snd_seq_device snd_pcm joydev snd_timer pcspkr virtio_balloon snd soundcore i2c_piix4 nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs qxl ata_generic pata_acpi drm_kms_helper virtio_net net_failover syscopyarea sysfillrect sysimgblt failover virtio_blk fb_sys_fops virtio_console ttm drm crc32c_intel serio_raw ata_piix virtio_pci libata virtio_ring virtio floppy dm_mirror dm_region_hash dm_log dm_mod CR2: 0000000000000000 Validating the control action within tcf_pedit_init() proved to fix the above issue. A TDC selftest is added to verify the correct behavior. Fixes: db50514f ("net: sched: add termination action to allow goto chain") Fixes: 97763dc0 ("net_sched: reject unknown tcfa_action values") Signed-off-by: -
Davide Caratti authored
the following script: # tc qdisc add dev crash0 clsact # tc filter add dev crash0 egress matchall \ > action nat ingress 1.18.1.1 1.18.2.2 pass index 90 # tc actions replace action nat \ > ingress 1.18.1.1 1.18.2.2 goto chain 42 index 90 cookie c1a0c1a0 # tc actions show action nat had the following output: Error: Failed to init TC action chain. We have an error talking to the kernel total acts 1 action order 0: nat ingress 1.18.1.1/32 1.18.2.2 goto chain 42 index 90 ref 2 bind 1 cookie c1a0c1a0 Then, the first packet transmitted by crash0 made the kernel crash: BUG: unable to handle kernel NULL pointer dereference at 0000000000000000 #PF error: [normal kernel read fault] PGD 800000002d180067 P4D 800000002d180067 PUD 7cb8b067 PMD 0 Oops: 0000 [#1] SMP PTI CPU: 3 PID: 164 Comm: kworker/3:1 Not tainted 5.0.0-rc4.gotochain_crash+ #533 Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011 Workqueue: ipv6_addrconf addrconf_dad_work RIP: 0010:tcf_action_exec+0xb8/0x100 Code: 00 00 00 20 74 1d 83 f8 03 75 09 49 83 c4 08 4d 39 ec 75 bc 48 83 c4 10 5b 5d 41 5c 41 5d 41 5e 41 5f c3 49 8b 97 a8 00 00 00 <48> 8b 12 48 89 55 00 48 83 c4 10 5b 5d 41 5c 41 5d 41 5e 41 5f c3 RSP: 0018:ffffae4500e2fad0 EFLAGS: 00010246 RAX: 000000002000002a RBX: ffff9fa52e28c800 RCX: 0000000001011201 RDX: 0000000000000000 RSI: 0000000000000056 RDI: ffff9fa52ca12800 RBP: ffffae4500e2fb70 R08: 0000000000000022 R09: 000000000000000e R10: 00000000ffffffff R11: 0000000001011201 R12: ffff9fa52cbc9c00 R13: ffff9fa52cbc9c08 R14: 0000000000000001 R15: ffff9fa52ca12780 FS: 0000000000000000(0000) GS:ffff9fa57db80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 0000000073f8c004 CR4: 00000000001606e0 Call Trace: tcf_classify+0x58/0x120 __dev_queue_xmit+0x40a/0x890 ? ndisc_next_option+0x50/0x50 ? ___neigh_create+0x4d5/0x680 ? ip6_finish_output2+0x1b5/0x590 ip6_finish_output2+0x1b5/0x590 ? ip6_output+0x68/0x110 ip6_output+0x68/0x110 ? nf_hook.constprop.28+0x79/0xc0 ndisc_send_skb+0x248/0x2e0 ndisc_send_ns+0xf8/0x200 ? addrconf_dad_work+0x389/0x4b0 addrconf_dad_work+0x389/0x4b0 ? __switch_to_asm+0x34/0x70 ? process_one_work+0x195/0x380 ? addrconf_dad_completed+0x370/0x370 process_one_work+0x195/0x380 worker_thread+0x30/0x390 ? process_one_work+0x380/0x380 kthread+0x113/0x130 ? kthread_park+0x90/0x90 ret_from_fork+0x35/0x40 Modules linked in: act_nat veth ip6table_filter ip6_tables iptable_filter binfmt_misc ext4 crct10dif_pclmul crc32_pclmul ghash_clmulni_intel mbcache jbd2 snd_hda_codec_generic snd_hda_intel snd_hda_codec snd_hwdep snd_hda_core snd_seq snd_seq_device snd_pcm aesni_intel crypto_simd cryptd glue_helper snd_timer snd joydev virtio_balloon pcspkr soundcore i2c_piix4 nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs qxl ata_generic pata_acpi drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ttm virtio_net virtio_blk net_failover failover virtio_console drm crc32c_intel floppy ata_piix libata virtio_pci virtio_ring virtio serio_raw dm_mirror dm_region_hash dm_log dm_mod CR2: 0000000000000000 Validating the control action within tcf_nat_init() proved to fix the above issue. A TDC selftest is added to verify the correct behavior. Fixes: db50514f ("net: sched: add termination action to allow goto chain") Fixes: 97763dc0 ("net_sched: reject unknown tcfa_action values") Signed-off-by: -
Davide Caratti authored
the following script: # tc qdisc add dev crash0 clsact # tc filter add dev crash0 egress matchall \ > action connmark pass index 90 # tc actions replace action connmark \ > goto chain 42 index 90 cookie c1a0c1a0 # tc actions show action connmark had the following output: Error: Failed to init TC action chain. We have an error talking to the kernel total acts 1 action order 0: connmark zone 0 goto chain 42 index 90 ref 2 bind 1 cookie c1a0c1a0 Then, the first packet transmitted by crash0 made the kernel crash: BUG: unable to handle kernel NULL pointer dereference at 0000000000000000 #PF error: [normal kernel read fault] PGD 0 P4D 0 Oops: 0000 [#1] SMP PTI CPU: 0 PID: 302 Comm: kworker/0:2 Not tainted 5.0.0-rc4.gotochain_crash+ #533 Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011 Workqueue: ipv6_addrconf addrconf_dad_work RIP: 0010:tcf_action_exec+0xb8/0x100 Code: 00 00 00 20 74 1d 83 f8 03 75 09 49 83 c4 08 4d 39 ec 75 bc 48 83 c4 10 5b 5d 41 5c 41 5d 41 5e 41 5f c3 49 8b 97 a8 00 00 00 <48> 8b 12 48 89 55 00 48 83 c4 10 5b 5d 41 5c 41 5d 41 5e 41 5f c3 RSP: 0018:ffff9bea406c3ad0 EFLAGS: 00010246 RAX: 000000002000002a RBX: ffff8c5dfc009f00 RCX: 0000000000000000 RDX: 0000000000000000 RSI: ffff9bea406c3a80 RDI: ffff8c5dfb9d6ec0 RBP: ffff9bea406c3b70 R08: ffff8c5dfda222a0 R09: ffffffff90933c3c R10: 0000000000000000 R11: 0000000092793f7d R12: ffff8c5df48b3c00 R13: ffff8c5df48b3c08 R14: 0000000000000001 R15: ffff8c5dfb9d6e40 FS: 0000000000000000(0000) GS:ffff8c5dfda00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 0000000062e0e006 CR4: 00000000001606f0 Call Trace: tcf_classify+0x58/0x120 __dev_queue_xmit+0x40a/0x890 ? ndisc_next_option+0x50/0x50 ? ___neigh_create+0x4d5/0x680 ? ip6_finish_output2+0x1b5/0x590 ip6_finish_output2+0x1b5/0x590 ? ip6_output+0x68/0x110 ip6_output+0x68/0x110 ? nf_hook.constprop.28+0x79/0xc0 ndisc_send_skb+0x248/0x2e0 ndisc_send_ns+0xf8/0x200 ? addrconf_dad_work+0x389/0x4b0 addrconf_dad_work+0x389/0x4b0 ? __switch_to_asm+0x34/0x70 ? process_one_work+0x195/0x380 ? addrconf_dad_completed+0x370/0x370 process_one_work+0x195/0x380 worker_thread+0x30/0x390 ? process_one_work+0x380/0x380 kthread+0x113/0x130 ? kthread_park+0x90/0x90 ret_from_fork+0x35/0x40 Modules linked in: act_connmark nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 veth ip6table_filter ip6_tables iptable_filter binfmt_misc ext4 crct10dif_pclmul mbcache crc32_pclmul jbd2 snd_hda_codec_generic ghash_clmulni_intel snd_hda_intel snd_hda_codec snd_hwdep snd_hda_core snd_seq snd_seq_device snd_pcm aesni_intel snd_timer crypto_simd cryptd snd glue_helper joydev virtio_balloon pcspkr soundcore i2c_piix4 nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs ata_generic pata_acpi qxl drm_kms_helper virtio_net net_failover syscopyarea virtio_blk failover virtio_console sysfillrect sysimgblt fb_sys_fops ttm drm ata_piix crc32c_intel serio_raw libata virtio_pci virtio_ring virtio floppy dm_mirror dm_region_hash dm_log dm_mod CR2: 0000000000000000 Validating the control action within tcf_connmark_init() proved to fix the above issue. A TDC selftest is added to verify the correct behavior. Fixes: db50514f ("net: sched: add termination action to allow goto chain") Fixes: 97763dc0 ("net_sched: reject unknown tcfa_action values") Signed-off-by: -
Davide Caratti authored
the following script: # tc qdisc add dev crash0 clsact # tc filter add dev crash0 egress matchall \ > action mirred ingress mirror dev lo pass # tc actions replace action mirred \ > ingress mirror dev lo goto chain 42 index 90 cookie c1a0c1a0 # tc actions show action mirred had the following output: Error: Failed to init TC action chain. We have an error talking to the kernel total acts 1 action order 0: mirred (Ingress Mirror to device lo) goto chain 42 index 90 ref 2 bind 1 cookie c1a0c1a0 Then, the first packet transmitted by crash0 made the kernel crash: Mirror/redirect action on BUG: unable to handle kernel NULL pointer dereference at 0000000000000000 #PF error: [normal kernel read fault] PGD 0 P4D 0 Oops: 0000 [#1] SMP PTI CPU: 3 PID: 47 Comm: kworker/3:1 Not tainted 5.0.0-rc4.gotochain_crash+ #533 Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011 Workqueue: ipv6_addrconf addrconf_dad_work RIP: 0010:tcf_action_exec+0xb8/0x100 Code: 00 00 00 20 74 1d 83 f8 03 75 09 49 83 c4 08 4d 39 ec 75 bc 48 83 c4 10 5b 5d 41 5c 41 5d 41 5e 41 5f c3 49 8b 97 a8 00 00 00 <48> 8b 12 48 89 55 00 48 83 c4 10 5b 5d 41 5c 41 5d 41 5e 41 5f c3 RSP: 0018:ffffa772404b7ad0 EFLAGS: 00010246 RAX: 000000002000002a RBX: ffff9c5afc3f4300 RCX: 0000000000000000 RDX: 0000000000000000 RSI: ffff9c5afdba9380 RDI: 0000000000029380 RBP: ffffa772404b7b70 R08: ffff9c5af7010028 R09: ffff9c5af7010029 R10: 0000000000000000 R11: ffff9c5af94c6a38 R12: ffff9c5af7953000 R13: ffff9c5af7953008 R14: 0000000000000001 R15: ffff9c5af7953d00 FS: 0000000000000000(0000) GS:ffff9c5afdb80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 000000007c514004 CR4: 00000000001606e0 Call Trace: tcf_classify+0x58/0x120 __dev_queue_xmit+0x40a/0x890 ? ndisc_next_option+0x50/0x50 ? ___neigh_create+0x4d5/0x680 ? ip6_finish_output2+0x1b5/0x590 ip6_finish_output2+0x1b5/0x590 ? ip6_output+0x68/0x110 ip6_output+0x68/0x110 ? nf_hook.constprop.28+0x79/0xc0 ndisc_send_skb+0x248/0x2e0 ndisc_send_ns+0xf8/0x200 ? addrconf_dad_work+0x389/0x4b0 addrconf_dad_work+0x389/0x4b0 ? __switch_to_asm+0x34/0x70 ? process_one_work+0x195/0x380 ? addrconf_dad_completed+0x370/0x370 process_one_work+0x195/0x380 worker_thread+0x30/0x390 ? process_one_work+0x380/0x380 kthread+0x113/0x130 ? kthread_park+0x90/0x90 ret_from_fork+0x35/0x40 Modules linked in: act_mirred veth ip6table_filter ip6_tables iptable_filter binfmt_misc ext4 crct10dif_pclmul snd_hda_codec_generic crc32_pclmul snd_hda_intel snd_hda_codec mbcache ghash_clmulni_intel jbd2 snd_hwdep snd_hda_core snd_seq snd_seq_device snd_pcm aesni_intel snd_timer snd crypto_simd cryptd glue_helper soundcore virtio_balloon joydev pcspkr i2c_piix4 nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs ata_generic pata_acpi qxl drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops virtio_net ttm virtio_blk net_failover virtio_console failover drm ata_piix crc32c_intel virtio_pci serio_raw libata virtio_ring virtio floppy dm_mirror dm_region_hash dm_log dm_mod CR2: 0000000000000000 Validating the control action within tcf_mirred_init() proved to fix the above issue. For the same reason, postpone the assignment of tcfa_action and tcfm_eaction to avoid partial reconfiguration of a mirred rule when it's replaced by another one that mirrors to a device that does not exist. A TDC selftest is added to verify the correct behavior. Fixes: db50514f ("net: sched: add termination action to allow goto chain") Fixes: 97763dc0 ("net_sched: reject unknown tcfa_action values") Signed-off-by: -
Davide Caratti authored
the following script: # tc qdisc add dev crash0 clsact # tc filter add dev crash0 egress matchall \ > action ife encode allow mark pass index 90 # tc actions replace action ife \ > encode allow mark goto chain 42 index 90 cookie c1a0c1a0 # tc action show action ife had the following output: IFE type 0xED3E IFE type 0xED3E Error: Failed to init TC action chain. We have an error talking to the kernel total acts 1 action order 0: ife encode action goto chain 42 type 0XED3E allow mark index 90 ref 2 bind 1 cookie c1a0c1a0 Then, the first packet transmitted by crash0 made the kernel crash: BUG: unable to handle kernel NULL pointer dereference at 0000000000000000 #PF error: [normal kernel read fault] PGD 800000007b4e7067 P4D 800000007b4e7067 PUD 7b4e6067 PMD 0 Oops: 0000 [#1] SMP PTI CPU: 2 PID: 164 Comm: kworker/2:1 Not tainted 5.0.0-rc4.gotochain_crash+ #533 Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011 Workqueue: ipv6_addrconf addrconf_dad_work RIP: 0010:tcf_action_exec+0xb8/0x100 Code: 00 00 00 20 74 1d 83 f8 03 75 09 49 83 c4 08 4d 39 ec 75 bc 48 83 c4 10 5b 5d 41 5c 41 5d 41 5e 41 5f c3 49 8b 97 a8 00 00 00 <48> 8b 12 48 89 55 00 48 83 c4 10 5b 5d 41 5c 41 5d 41 5e 41 5f c3 RSP: 0018:ffffa6a7c0553ad0 EFLAGS: 00010246 RAX: 000000002000002a RBX: ffff9796ee1bbd00 RCX: 0000000000000001 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000 RBP: ffffa6a7c0553b70 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: ffff9797385bb038 R12: ffff9796ead9d700 R13: ffff9796ead9d708 R14: 0000000000000001 R15: ffff9796ead9d800 FS: 0000000000000000(0000) GS:ffff97973db00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 000000007c41e006 CR4: 00000000001606e0 Call Trace: tcf_classify+0x58/0x120 __dev_queue_xmit+0x40a/0x890 ? ndisc_next_option+0x50/0x50 ? ___neigh_create+0x4d5/0x680 ? ip6_finish_output2+0x1b5/0x590 ip6_finish_output2+0x1b5/0x590 ? ip6_output+0x68/0x110 ip6_output+0x68/0x110 ? nf_hook.constprop.28+0x79/0xc0 ndisc_send_skb+0x248/0x2e0 ndisc_send_ns+0xf8/0x200 ? addrconf_dad_work+0x389/0x4b0 addrconf_dad_work+0x389/0x4b0 ? __switch_to_asm+0x34/0x70 ? process_one_work+0x195/0x380 ? addrconf_dad_completed+0x370/0x370 process_one_work+0x195/0x380 worker_thread+0x30/0x390 ? process_one_work+0x380/0x380 kthread+0x113/0x130 ? kthread_park+0x90/0x90 ret_from_fork+0x35/0x40 Modules linked in: act_gact act_meta_mark act_ife dummy veth ip6table_filter ip6_tables iptable_filter binfmt_misc snd_hda_codec_generic ext4 snd_hda_intel snd_hda_codec crct10dif_pclmul mbcache crc32_pclmul jbd2 snd_hwdep snd_hda_core ghash_clmulni_intel snd_seq snd_seq_device snd_pcm snd_timer aesni_intel crypto_simd snd cryptd glue_helper virtio_balloon joydev pcspkr soundcore i2c_piix4 nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs ata_generic pata_acpi qxl virtio_net drm_kms_helper virtio_blk net_failover syscopyarea failover sysfillrect virtio_console sysimgblt fb_sys_fops ttm drm crc32c_intel serio_raw ata_piix virtio_pci virtio_ring libata virtio floppy dm_mirror dm_region_hash dm_log dm_mod [last unloaded: act_ife] CR2: 0000000000000000 Validating the control action within tcf_ife_init() proved to fix the above issue. A TDC selftest is added to verify the correct behavior. Fixes: db50514f ("net: sched: add termination action to allow goto chain") Fixes: 97763dc0 ("net_sched: reject unknown tcfa_action values") Signed-off-by:
-
