The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.

Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.

Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Christophe Leroy says:

====================
Optimisation of fs_enet ethernet driver

This set optimises the freescale fs_enet ethernet driver:
1/ Merge of RX and TX NAPI functions in order to limit the amount of
interrupts
2/ Do not unmap DMA when packets len is below copybreak, otherwise there
is no benefit in copying the skb instead of allocating a new one
3/ Make copybreak value configurable as the optimised value is not the
same on all targets
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Measurement shows that on a MPC8xx running at 132MHz, the optimal
limit is 112:
* 114 bytes packets are processed in 147 TB ticks with higher copybreak
* 114 bytes packets are processed in 148 TB ticks with lower copybreak
* 128 bytes packets are processed in 154 TB ticks with higher copybreak
* 128 bytes packets are processed in 148 TB ticks with lower copybreak
* 238 bytes packets are processed in 172 TB ticks with higher copybreak
* 238 bytes packets are processed in 148 TB ticks with lower copybreak

However it might be different on other processors
and/or frequencies. So it is useful to make it configurable.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the length of the packet is below the defined copybreak limit,
the received packet is copied into a newly allocated skb in order
to reuse the skb. This is only interesting if it allow us to avoid
a new DMA mapping. We shall therefore not DMA unmap and remap the
skb->data. Instead, we invalidate the cache
with dma_sync_single_for_cpu() once the received data has been
copied into the new skb.

The following measures have been obtained on a mpc885 running at 132Mhz.
Measurement is done using the timebase with packets sent to the target
with 'ping -s 1' (packet len is 60):
* Without this patch: 182 TB ticks
* With this patch: 143 TB ticks

As a comparison, if we set the copybreak limit to 0, then we get
148 TB ticks. It means that without this patch, duration is even
worse when copying received data to a new skb instead of
allocating a new skb for next packet to be received
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Initially, a NAPI TX routine has been implemented separately from
NAPI RX, as done on the freescale/gianfar driver.

By merging NAPI RX and NAPI TX, we reduce the amount of TX completion
interrupts.

Handling of the budget in association with TX interrupts is based on
indications provided at https://wiki.linuxfoundation.org/networking/napi
We never proceed more than the complete TX ring on a single run.

At the same time, we fix an issue in the handling of fep->tx_free:

It is only when fep->tx_free goes up to MAX_SKB_FRAGS that
we need to wake up the queue. There is no need to call
netif_wake_queue() at every packet successfully transmitted.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hadar Hen Zion says:

====================
net/sched: ip tunnel metadata set/release/classify by using TC

This patchset introduces ip tunnel manipulation support using the TC subsystem.

In the decap flow, it enables the user to redirect packets from a shared tunnel
device and classify by outer and inner headers. The outer headers are extracted
from the metadata and used by the flower filter. A new action act_tunnel_key,
releases the metadata.

In the encap flow, act_tunnel_key creates a metadata object to be used by the
shared tunnel device. The actual redirection to the tunnel device is done using
act_mirred.

For example:
$ tc qdisc add dev vnet0 ingress
$ tc filter add dev vnet0 protocol ip parent ffff: \
	flower \
	 ip_proto 1 \
	action tunnel_key set \
	 src_ip 11.11.0.1 \
	 dst_ip 11.11.0.2 \
	 id 11 \
	action mirred egress redirect dev vxlan0

$ tc qdisc add dev vxlan0 ingress
$ tc filter add dev vxlan0 protocol ip parent ffff: \
	flower \
	 enc_src_ip 11.11.0.2 \
	 enc_dst_ip 11.11.0.1 \
	 enc_key_id 11 \
	action tunnel_key release \
	action mirred egress redirect dev vnet0

Amir & Hadar

Changes from V6:
- Add kfree_rcu to tunnel_key_release function
- Use reverse Christmas tree order in tunnel_key_init function

Changes from V5:
- Add __rcu notation to struct tcf_tunnel_key_params in struct tcf_tunnel_key
- Fix indentation in include/net/dst_metadata.h
- Fix syntx error in commit message

Changes from V4:
- Fix tunnel_key_init function error flow.
- Add 'action' variable to struct tcf_tunnel_key_params and use it instead of
  tcf_action variable which is not protected by rcu lock.

Changes from V3:
- Use percpu stats
- No spinlock on datapatch - protecting parameters with rcu
- Fix buggy handling of set/release dst
- Use nla_get_in_addr and nla_put_in_addr
- Fix change logs
- Pass in6_addr by pointer
- Rename utility functions to start with double underscore

Changes from V2:
- Use union in struct fl_flow_key for enc_ipv6 and enc_ipv4.
- Rename functions _ip_tun_rx_dst and _ipv6_tun_rx_dst to _ip_tun_set_dst and
  _ipv6_tun_set_dst accordingly.
- Remove local parameter 'encapdecap' from tunnel_key_init function.
- Don't copy in6_addr values in tunnel_key_dump_addresses function, use pointers.

Changes from V1:
- More cleanups to key32_to_tunnel_id() and tunnel_id_to_key32()
- IPv6 Support added
- Set TUNNEL_KEY flag to make GRE work
- Handle zero tunnel id properly in act_tunnel_key
- Don't leave junk in decap action
- Fix bug in act_tunnel_key initialization where (exists & ocr) is true
- Remove BUG() from code
- Rename action to tunnel_key
- Improve grep-ability of code
- Reuse code from ip_tun_rx_dst() and ipv6_tun_rx_dst()

Changes from RFC:
- Add a new action instead of making mirred too complex
- No need to specify UDP port in action - it is already in the tunnel device
  configuration
- Added a decap operation to drop tunnel metadata
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This action could be used before redirecting packets to a shared tunnel
device, or when redirecting packets arriving from a such a device.

The action will release the metadata created by the tunnel device
(decap), or set the metadata with the specified values for encap
operation.

For example, the following flower filter will forward all ICMP packets
destined to 11.11.11.2 through the shared vxlan device 'vxlan0'. Before
redirecting, a metadata for the vxlan tunnel is created using the
tunnel_key action and it's arguments:

$ tc filter add dev net0 protocol ip parent ffff: \
    flower \
      ip_proto 1 \
      dst_ip 11.11.11.2 \
    action tunnel_key set \
      src_ip 11.11.0.1 \
      dst_ip 11.11.0.2 \
      id 11 \
    action mirred egress redirect dev vxlan0
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce classifying by metadata extracted by the tunnel device.
Outer header fields - source/dest ip and tunnel id, are extracted from
the metadata when classifying.

For example, the following will add a filter on the ingress Qdisc of shared
vxlan device named 'vxlan0'. To forward packets with outer src ip
11.11.0.2, dst ip 11.11.0.1 and tunnel id 11. The packets will be
forwarded to tap device 'vnet0' (after metadata is released):

$ tc filter add dev vxlan0 protocol ip parent ffff: \
    flower \
      enc_src_ip 11.11.0.2 \
      enc_dst_ip 11.11.0.1 \
      enc_key_id 11 \
      dst_ip 11.11.11.1 \
    action tunnel_key release \
    action mirred egress redirect dev vnet0

The action tunnel_key, will be introduced in the next patch in this
series.
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extract __ip_tun_set_dst() and __ipv6_tun_set_dst() out of
ip_tun_rx_dst() and ipv6_tun_rx_dst(), to be used without supplying an
skb.
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add utility functions to convert a 32 bits key into a 64 bits tunnel and
vice versa.
These functions will be used instead of cloning code in GRE and VXLAN,
and in tc act_iptunnel which will be introduced in a following patch in
this patchset.
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* Multiplications for the size determination of memory allocations
  indicated that array data structures should be processed.
  Thus use the corresponding function "kmalloc_array".

  This issue was detected by using the Coccinelle software.

* Replace the specification of data types by pointer dereferences
  to make the corresponding size determination a bit safer according to
  the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tobias Regnery says:

====================
alx: add msi-x support

This patchset adds msi-x support to the alx driver. It is a preparatory
series for multi queue support, which I am currently working on. As there
is no advantage over msi interrupts without multi queue support, msi-x
interrupts are disabled by default. In order to test for regressions, a
new module parameter is added to enable msi-x interrupts.

Based on information of the downstream driver at github.com/qca/alx
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

msi-x support is default disabled in the alx driver. In order to test msi-x
interrupts for regressions add a module parameter to the driver.
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add msi-x support to the alx driver. This is in preparation for multi queue
support.

msi-x interrupts are disabled by default because without multi queue support
there is no advantage over msi interrupts. The performance numbers observed
with iperf stay the same.

Based on information of the downstream driver at github.com/qca/alx
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Factor out the handling of misc interrupts into a new function.
This function can be reused later for msi-x interrupts.
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce a new flag field for the advanced interrupt capatibilities and add
new functions to enable and disable msi interrupts. These functions will be
extended later to cover msi-x interrupts.

We enable msi interrupts earlier in alx_init_intr because with msi-x and multi
queue support the number of queues must be set before we allocate resources for
the rx and tx paths.
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We get a few warnings when building kernel with W=1:
drivers/net/ethernet/qlogic/qed/qed_l2.c:112:5: warning: no previous prototype for 'qed_sp_vport_start' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_sriov.c:110:6: warning: no previous prototype for 'qed_iov_is_valid_vfid' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_sriov.c:188:5: warning: no previous prototype for 'qed_iov_post_vf_bulletin' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_sriov.c:578:6: warning: no previous prototype for 'qed_iov_set_vfs_to_disable' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_sriov.c:1135:28: warning: no previous prototype for 'qed_iov_get_public_vf_info' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_sriov.c:1148:6: warning: no previous prototype for 'qed_iov_clean_vf' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_sriov.c:2444:5: warning: no previous prototype for 'qed_iov_chk_ucast' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_sriov.c:2762:5: warning: no previous prototype for 'qed_iov_vf_flr_cleanup' [-Wmissing-prototypes]
....

In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
so this patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
Some BPF helper cleanups

This series contains a couple of misc cleanups and improvements
for BPF helpers. For details please see individual patches. We
let this also sit for a few days with Fengguang's kbuild test
robot, and there were no issues seen (besides one false positive,
see last one for details).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This work adds BPF_CALL_<n>() macros and converts all the eBPF helper functions
to use them, in a similar fashion like we do with SYSCALL_DEFINE<n>() macros
that are used today. Motivation for this is to hide all the register handling
and all necessary casts from the user, so that it is done automatically in the
background when adding a BPF_CALL_<n>() call.

This makes current helpers easier to review, eases to write future helpers,
avoids getting the casting mess wrong, and allows for extending all helpers at
once (f.e. build time checks, etc). It also helps detecting more easily in
code reviews that unused registers are not instrumented in the code by accident,
breaking compatibility with existing programs.

BPF_CALL_<n>() internals are quite similar to SYSCALL_DEFINE<n>() ones with some
fundamental differences, for example, for generating the actual helper function
that carries all u64 regs, we need to fill unused regs, so that we always end up
with 5 u64 regs as an argument.

I reviewed several 0-5 generated BPF_CALL_<n>() variants of the .i results and
they look all as expected. No sparse issue spotted. We let this also sit for a
few days with Fengguang's kbuild test robot, and there were no issues seen. On
s390, it barked on the "uses dynamic stack allocation" notice, which is an old
one from bpf_perf_event_output{,_tp}() reappearing here due to the conversion
to the call wrapper, just telling that the perf raw record/frag sits on stack
(gcc with s390's -mwarn-dynamicstack), but that's all. Did various runtime tests
and they were fine as well. All eBPF helpers are now converted to use these
macros, getting rid of a good chunk of all the raw castings.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When fetching ifindex, we don't need to test dev for being NULL since
we're always guaranteed to have a valid dev for clsact programs. Thus,
avoid this test in fast path.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add BPF_SIZEOF() and BPF_FIELD_SIZEOF() macros to improve the code a bit
which otherwise often result in overly long bytes_to_bpf_size(sizeof())
and bytes_to_bpf_size(FIELD_SIZEOF()) lines. So place them into a macro
helper instead. Moreover, we currently have a BUILD_BUG_ON(BPF_FIELD_SIZEOF())
check in convert_bpf_extensions(), but we should rather make that generic
as well and add a BUILD_BUG_ON() test in all BPF_SIZEOF()/BPF_FIELD_SIZEOF()
users to detect any rewriter size issues at compile time. Note, there are
currently none, but we want to assert that it stays this way.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some minor misc cleanups, f.e. use sizeof(__u32) instead of hardcoding
and in __bpf_skb_max_len(), I missed that we always have skb->dev valid
anyway, so we can drop the unneeded test for dev; also few more other
misc bits addressed here.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

If skb has a valid l4 hash, there is no point clearing hash and force
a further flow dissection when a tunnel encapsulation is added.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* Multiplications for the size determination of memory allocations
  indicated that array data structures should be processed.
  Thus use the corresponding function "kmalloc_array".

  This issue was detected by using the Coccinelle software.

* Replace the specification of data types by pointer dereferences
  to make the corresponding size determination a bit safer according to
  the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

* A multiplication for the size determination of a memory allocation
  indicated that an array data structure should be processed.
  Thus use the corresponding function "kmalloc_array".

  This issue was detected by using the Coccinelle software.

* Replace the specification of a data structure by a pointer dereference
  to make the corresponding size determination a bit safer according to
  the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'rxrpc-rewrite-20160908' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs

David Howells says:

====================
rxrpc: Rewrite data and ack handling

This patch set constitutes the main portion of the AF_RXRPC rewrite.  It
consists of five fix/helper patches:

 (1) Fix ASSERTCMP's and ASSERTIFCMP's handling of signed values.

 (2) Update some protocol definitions slightly.

 (3) Use of an hlist for RCU purposes.

 (4) Removal of per-call sk_buff accounting (not really needed when skbs
     aren't being queued on the main queue).

 (5) Addition of a tracepoint to log incoming packets in the data_ready
     callback and to log the end of the data_ready callback.

And then there are two patches that form the main part:

 (6) Preallocation of resources for incoming calls so that in patch (7) the
     data_ready handler can be made to fully instantiate an incoming call
     and make it live.  This extends through into AFS so that AFS can
     preallocate its own incoming call resources.

     The preallocation size is capped at the listen() backlog setting - and
     that is capped at a sysctl limit which can be set between 4 and 32.

     The preallocation is (re)charged either by accepting/rejecting pending
     calls or, in the case of AFS, manually.  If insufficient preallocation
     resources exist, a BUSY packet will be transmitted.

     The advantage of using this preallocation is that once a call is set
     up in the data_ready handler, DATA packets can be queued on it
     immediately rather than the DATA packets being queued for a background
     work item to do all the allocation and then try and sort out the DATA
     packets whilst other DATA packets may still be coming in and going
     either to the background thread or the new call.

 (7) Rewrite the handling of DATA, ACK and ABORT packets.

     In the receive phase, DATA packets are now held in per-call circular
     buffers with deduplication, out of sequence detection and suchlike
     being done in data_ready.  Since there is only one producer and only
     once consumer, no locks need be used on the receive queue.

     Received ACK and ABORT packets are now parsed and discarded in
     data_ready to recycle resources as fast as possible.

     sk_buffs are no longer pulled, trimmed or cloned, but rather the
     offset and size of the content is tracked.  This particularly affects
     jumbo DATA packets which need insertion into the receive buffer in
     multiple places.  Annotations are kept to track which bit is which.

     Packets are no longer queued on the socket receive queue; rather,
     calls are queued.  Dummy packets to convey events therefore no longer
     need to be invented and metadata packets can be discarded as soon as
     parsed rather then being pushed onto the socket receive queue to
     indicate terminal events.

     The preallocation facility added in (6) is now used to set up incoming
     calls with very little locking required and no calls to the allocator
     in data_ready.

     Decryption and verification is now handled in recvmsg() rather than in
     a background thread.  This allows for the future possibility of
     decrypting directly into the user buffer.

     With this patch, the code is a lot simpler and most of the mass of
     call event and state wangling code in call_event.c is gone.

With this, the majority of the AF_RXRPC rewrite is complete.  However,
there are still things to be done, including:

 (*) Limit the number of active service calls to prevent an attacker from
     filling up a server's memory.

 (*) Limit the number of calls on the rebuff-with-BUSY queue.

 (*) Transmit delayed/deferred ACKs from recvmsg() if possible, rather than
     punting to the background thread.  Ideally, the background thread
     shouldn't run at all, but data_ready can't call kernel_sendmsg() and
     we can't rely on recvmsg() attending to the call in a timely fashion.

 (*) Prevent the call at the front of the socket queue from hogging
     recvmsg()'s attention if there's a sufficiently continuous supply of
     data.

 (*) Distribute ICMP errors by connection rather than by call.  Possibly
     parse the ICMP packet to try and pin down the exact connection and
     call.

 (*) Encrypt/decrypt directly between user buffers and socket buffers where
     possible.

 (*) IPv6.

 (*) Service ID upgrade.  This is a facility whereby a special flag bit is
     set in the DATA packet header when making a call that tells the server
     that it is allowed to change the service ID to an upgraded one and
     reply with an equivalent call from the upgraded service.

     This is used, for example, to override certain AFS calls so that IPv6
     addresses can be returned.

 (*) Allow userspace to preallocate call user IDs for incoming calls.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

tdinfo->skb_dma is a 7 element array of dma_addr_t hence cannot be
null, so the pull pointer check on tdinfo->skb_dma  is redundant.
Remove it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We get 1 warning when building kernel with W=1:
drivers/net/ethernet/qlogic/qede/qede_main.c:2113:5: warning: no previous prototype for 'qede_set_features' [-Wmissing-prototypes]

In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
so this patch marks this function with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The existing VSC85xx PHY driver did not follow the coding style and caused "checkpatch" to complain. This commit fixes this.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dtefacs.calling_ae and called_ae are both 20 element __u8 arrays and
cannot be null and hence are redundant checks. Remove these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The netdevice type structure for macsec was being defined but never used.
To set the network device type the macro SET_NETDEV_DEVTYPE must be called.
Compile tested only, I don't use macsec.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This structure is defined but never used. Flagged with W=1
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Guillaume Nault says:

====================
ip: fix creation flags reported in RTM_NEWROUTE events

Netlink messages sent to user-space upon RTM_NEWROUTE events have their
nlmsg_flags field inconsistently set. While the NLM_F_REPLACE and
NLM_F_APPEND bits are correctly handled, NLM_F_CREATE and NLM_F_EXCL
are always 0.

This series sets the NLM_F_CREATE and NLM_F_EXCL bits when applicable,
for IPv4 and IPv6.

Since IPv6 ignores the NLM_F_APPEND flags in requests, this flag isn't
reported in RTM_NEWROUTE IPv6 events. This keeps IPv6 internal
consistency (same flag semantic for user requests and kernel events) at
the cost of bringing different flag interpretation for IPv4 and IPv6.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 37a1d361 ("ipv6: include NLM_F_REPLACE in route
replace notifications"), RTM_NEWROUTE notifications have their
NLM_F_REPLACE flag set if the new route replaced a preexisting one.
However, other flags aren't set.

This patch reports the missing NLM_F_CREATE and NLM_F_EXCL flag bits.

NLM_F_APPEND is not reported, because in ipv6 a NLM_F_CREATE request
is interpreted as an append request (contrary to ipv4, "prepend" is not
supported, so if NLM_F_EXCL is not set then NLM_F_APPEND is implicit).

As a result, the possible flag combination can now be reported
(iproute2's terminology into parentheses):

  * NLM_F_CREATE | NLM_F_EXCL: route didn't exist, exclusive creation
    ("add").
  * NLM_F_CREATE: route did already exist, new route added after
    preexisting ones ("append").
  * NLM_F_REPLACE: route did already exist, new route replaced the
    first preexisting one ("change").
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

fib_table_insert() inconsistently fills the nlmsg_flags field in its
notification messages.

Since commit b8f55831 ("[RTNETLINK]: Fix sending netlink message
when replace route."), the netlink message has its nlmsg_flags set to
NLM_F_REPLACE if the route replaced a preexisting one.

Then commit a2bb6d7d ("ipv4: include NLM_F_APPEND flag in append
route notifications") started setting nlmsg_flags to NLM_F_APPEND if
the route matched a preexisting one but was appended.

In other cases (exclusive creation or prepend), nlmsg_flags is 0.

This patch sets ->nlmsg_flags in all situations, preserving the
semantic of the NLM_F_* bits:

  * NLM_F_CREATE: a new fib entry has been created for this route.
  * NLM_F_EXCL: no other fib entry existed for this route.
  * NLM_F_REPLACE: this route has overwritten a preexisting fib entry.
  * NLM_F_APPEND: the new fib entry was added after other entries for
    the same route.

As a result, the possible flag combination can now be reported
(iproute2's terminology into parentheses):

  * NLM_F_CREATE | NLM_F_EXCL: route didn't exist, exclusive creation
    ("add").
  * NLM_F_CREATE | NLM_F_APPEND: route did already exist, new route
    added after preexisting ones ("append").
  * NLM_F_CREATE: route did already exist, new route added before
    preexisting ones ("prepend").
  * NLM_F_REPLACE: route did already exist, new route replaced the
    first preexisting one ("change").
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit f02db315 ("ipv4: IP_TOS and IP_TTL can be specified as
ancillary data") Francesco added IP_TOS values specified as integer.

However, kernel sends to userspace (at recvmsg() time) an IP_TOS value
in a single byte, when IP_RECVTOS is set on the socket.

It can be very useful to reflect all ancillary options as given by the
kernel in a subsequent sendmsg(), instead of aborting the sendmsg() with
EINVAL after Francesco patch.

So this patch extends IP_TOS ancillary to accept an u8, so that an UDP
server can simply reuse same ancillary block without having to mangle
it.

Jesper can then augment
https://github.com/netoptimizer/network-testing/blob/master/src/udp_example02.c
to add TOS reflection ;)

Fixes: f02db315 ("ipv4: IP_TOS and IP_TTL can be specified as ancillary data")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Francesco Fusco <ffusco@redhat.com>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

LLVM can generate code that tests for direct packet access via
skb->data/data_end in a way that currently gets rejected by the
verifier, example:

  [...]
   7: (61) r3 = *(u32 *)(r6 +80)
   8: (61) r9 = *(u32 *)(r6 +76)
   9: (bf) r2 = r9
  10: (07) r2 += 54
  11: (3d) if r3 >= r2 goto pc+12
   R1=inv R2=pkt(id=0,off=54,r=0) R3=pkt_end R4=inv R6=ctx
   R9=pkt(id=0,off=0,r=0) R10=fp
  12: (18) r4 = 0xffffff7a
  14: (05) goto pc+430
  [...]

  from 11 to 24: R1=inv R2=pkt(id=0,off=54,r=0) R3=pkt_end R4=inv
                 R6=ctx R9=pkt(id=0,off=0,r=0) R10=fp
  24: (7b) *(u64 *)(r10 -40) = r1
  25: (b7) r1 = 0
  26: (63) *(u32 *)(r6 +56) = r1
  27: (b7) r2 = 40
  28: (71) r8 = *(u8 *)(r9 +20)
  invalid access to packet, off=20 size=1, R9(id=0,off=0,r=0)

The reason why this gets rejected despite a proper test is that we
currently call find_good_pkt_pointers() only in case where we detect
tests like rX > pkt_end, where rX is of type pkt(id=Y,off=Z,r=0) and
derived, for example, from a register of type pkt(id=Y,off=0,r=0)
pointing to skb->data. find_good_pkt_pointers() then fills the range
in the current branch to pkt(id=Y,off=0,r=Z) on success.

For above case, we need to extend that to recognize pkt_end >= rX
pattern and mark the other branch that is taken on success with the
appropriate pkt(id=Y,off=0,r=Z) type via find_good_pkt_pointers().
Since eBPF operates on BPF_JGT (>) and BPF_JGE (>=), these are the
only two practical options to test for from what LLVM could have
generated, since there's no such thing as BPF_JLT (<) or BPF_JLE (<=)
that we would need to take into account as well.

After the fix:

  [...]
   7: (61) r3 = *(u32 *)(r6 +80)
   8: (61) r9 = *(u32 *)(r6 +76)
   9: (bf) r2 = r9
  10: (07) r2 += 54
  11: (3d) if r3 >= r2 goto pc+12
   R1=inv R2=pkt(id=0,off=54,r=0) R3=pkt_end R4=inv R6=ctx
   R9=pkt(id=0,off=0,r=0) R10=fp
  12: (18) r4 = 0xffffff7a
  14: (05) goto pc+430
  [...]

  from 11 to 24: R1=inv R2=pkt(id=0,off=54,r=54) R3=pkt_end R4=inv
                 R6=ctx R9=pkt(id=0,off=0,r=54) R10=fp
  24: (7b) *(u64 *)(r10 -40) = r1
  25: (b7) r1 = 0
  26: (63) *(u32 *)(r6 +56) = r1
  27: (b7) r2 = 40
  28: (71) r8 = *(u8 *)(r9 +20)
  29: (bf) r1 = r8
  30: (25) if r8 > 0x3c goto pc+47
   R1=inv56 R2=imm40 R3=pkt_end R4=inv R6=ctx R8=inv56
   R9=pkt(id=0,off=0,r=54) R10=fp
  31: (b7) r1 = 1
  [...]

Verifier test cases are also added in this work, one that demonstrates
the mentioned example here and one that tries a bad packet access for
the current/fall-through branch (the one with types pkt(id=X,off=Y,r=0),
pkt(id=X,off=0,r=0)), then a case with good and bad accesses, and two
with both test variants (>, >=).

Fixes: 969bf05e ("bpf: direct packet access")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Over the years, TCP BDP has increased by several orders of magnitude,
and some people are considering to reach the 2 Gbytes limit.

Even with current window scale limit of 14, ~1 Gbytes maps to ~740,000
MSS.

In presence of packet losses (or reorders), TCP stores incoming packets
into an out of order queue, and number of skbs sitting there waiting for
the missing packets to be received can be in the 10^5 range.

Most packets are appended to the tail of this queue, and when
packets can finally be transferred to receive queue, we scan the queue
from its head.

However, in presence of heavy losses, we might have to find an arbitrary
point in this queue, involving a linear scan for every incoming packet,
throwing away cpu caches.

This patch converts it to a RB tree, to get bounded latencies.

Yaogong wrote a preliminary patch about 2 years ago.
Eric did the rebase, added ofo_last_skb cache, polishing and tests.

Tested with network dropping between 1 and 10 % packets, with good
success (about 30 % increase of throughput in stress tests)

Next step would be to also use an RB tree for the write queue at sender
side ;)
Signed-off-by: Yaogong Wang <wygivan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-By: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric Garver says:

====================
openvswitch: add 802.1ad support

This series adds 802.1ad support to openvswitch. It is a continuation of the
work originally started by Thomas F Herbert - hence the large rev number.

The extra VLAN is implemented by using an additional level of the
OVS_KEY_ATTR_ENCAP netlink attribute.
In OVS flow speak, this looks like

   eth_type(0x88a8),vlan(vid=100),encap(eth_type(0x8100), vlan(vid=200),
                                        encap(eth_type(0x0800), ...))

The userspace counterpart has also seen recent activity on the ovs-dev mailing
lists. There are some new 802.1ad OVS tests being added - also on the ovs-dev
list. This patch series has been tested using the most recent version of
userspace (v3) and tests (v2).

v22 changes:
  - merge patch 4 into patch 3
  - fix checkpatch.pl errors
    - Still some 80 char warnings for long string literals
  - refresh pointer after pskb_may_pull()
  - refactor vlan nlattr parsing to remove some double checks
  - introduce ovs_nla_put_vlan()
  - move triple VLAN check to after ethertype serialization
  - WARN_ON_ONCE() on triple VLAN and unexpected encap values

v21 changes:
  - Fix (and simplify) netlink attribute parsing
  - re-add handling of truncated VLAN tags
  - fix if/else dangling assignment in {push,pop}_vlan()
  - simplify parse_vlan()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>