- 28 Jun, 2018 40 commits
-
-
Ezequiel Garcia authored
Currently, rga_buf_start_streaming() is expecting pm_runtime_get_sync to return zero on success, which is wrong. As per the documentation, pm_runtime_get_sync increments the device's usage counter and return its result. This means it will typically return a positive integer on success and a negative error code. Therefore, rockchip-rga driver is currently unusable failing to start_streaming in most cases. Fix it and while here, cleanup the buffer return-to-core logic. Fixes: f7e7b48e ("[media] rockchip/rga: v4l2 m2m support") Signed-off-by:
Ezequiel Garcia <ezequiel@collabora.com> Reviewed-by:
Jacob Chen <jacob-chen@iotwrt.com> [hans.verkuil@cisco.com: fix line over 80 cols warning] Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Alexandre Courbot authored
When checking a format for validity, the resolution is reset to 1280x720 whenever the pixel format is not supported. This behavior can mislead user-space into believing that this is the only resolution supported, and looks strange considering that if we try/set the same format with just the pixel format changed to a valid one, the call will this time succeed without altering the resolution. Resolution is managed independently of the pixel format, so remove this reset. Signed-off-by:
Alexandre Courbot <acourbot@chromium.org> Acked-by:
Stanimir Varbanov <stanimir.varbanov@linaro.org> Signed-off-by:
-
Zhouyang Jia authored
When dvb_register_adapter fails, the lack of error-handling code may cause unexpected results. This patch adds error-handling code after calling dvb_register_adapter. Signed-off-by:
Zhouyang Jia <jiazhouyang09@gmail.com> [hans.verkuil@cisco.com: use pr_err and fix typo: adater -> adapter] Signed-off-by:
-
Zhouyang Jia authored
When snd_ctl_add fails, the lack of error-handling code may cause unexpected results. This patch adds error-handling code after calling snd_ctl_add. Signed-off-by:
-
Colin Ian King authored
The check for a zero retval is redundant as all paths that lead to this point have set retval to an error return value that is non-zero. Remove the redundant check. Detected by CoverityScan, CID#102589 ("Logically dead code") Signed-off-by:Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Ezequiel Garcia authored
If there is a schedulable job, v4l2_m2m_try_schedule() calls v4l2_m2m_try_run(). This makes the unconditional v4l2_m2m_try_run() called by v4l2_m2m_job_finish superfluous. Remove it. Fixes: 7f98639d ("V4L/DVB: add memory-to-memory device helper framework for videobuf") Signed-off-by:
-
Anton Leontiev authored
Name is already initialized by assignment from rga_videodev. Signed-off-by:
Anton Leontiev <scileont@gmail.com> Signed-off-by:
-
Anton Leontiev authored
Name is already initialized by assignment from deinterlace_videodev. Signed-off-by:
-
Anton Leontiev authored
Name is already initialized by assignment from emmaprp_videodev. Signed-off-by:
-
Anton Leontiev authored
Name is already initialized by assignment from g2d_videodev. Signed-off-by:
-
Anton Leontiev authored
Name is already initialized by assignment from vpe_videodev. Signed-off-by:
-
Anton Leontiev authored
Name is already initialized by assignment from vim2m_videodev. Signed-off-by:
-
Colin Ian King authored
Trivial fix to spelling mistake in pr_notice message text Signed-off-by:
-
Steve Longerbeam authored
The ADV748x CSI-2 subdevices are HDMI/AFE to MIPI CSI-2 bridges. Signed-off-by:
Steve Longerbeam <steve_longerbeam@mentor.com> Acked-by:
Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Signed-off-by:
-
Corentin Labbe authored
Those two files are unused since commit 486a7a28 ("[media] cx25821: remove cx25821-audio-upstream.c") and commit b6f21dc3 ("[media] cx25821: remove video output support") Remove them from tree. Signed-off-by:
Corentin Labbe <clabbe@baylibre.com> Signed-off-by:
-
Hugues Fruchet authored
Implements runtime & system sleep power management ops. Signed-off-by:
Hugues Fruchet <hugues.fruchet@st.com> Signed-off-by:
-
Nicholas Mc Guire authored
This does not fix any bug - this is just a code simplification. As np is not used after passing it to v4l2_fwnode_endpoint_parse() its refcount can be decremented immediately and at one location. Signed-off-by:
Nicholas Mc Guire <hofrat@osadl.org> Signed-off-by:
-
Nicholas Mc Guire authored
The endpoint allocated by of_graph_get_next_endpoint() needs an of_node_put() in both error and success path. As ep is not used the refcount decrement can be right after the last use of ep. Fixes: commit 37404f91 ("[media] stm32-dcmi: STM32 DCMI camera interface driver") Signed-off-by:
-
Nicholas Mc Guire authored
The while(1) is effectively useless as all possible paths within it return thus there is no way to loop. Signed-off-by:
-
Hugues Fruchet authored
Do not wait for interrupt completion when stopping streaming, stopping sensor and disabling interruptions are enough. Signed-off-by:
-
Hugues Fruchet authored
Cleanup "active" field usage and enhance list management to avoid exceptions when releasing buffers on error or stopping streaming. Signed-off-by:
-
Hugues Fruchet authored
Introduce WAIT_FOR_BUFFER state instead of "active" field checking to manage buffer starvation case. Signed-off-by:
-
Hugues Fruchet authored
Return buffer to V4L2 in error state if DMA error occurs. Signed-off-by:
-
Hugues Fruchet authored
Return silently instead of falling into error when running out of available buffers when restarting capture. Capture will be restarted when new buffers will be provided by V4L2 client. Signed-off-by:
-
Hugues Fruchet authored
Minor non-functional fixes around comments, variable namings and trace point enhancement. Signed-off-by:
-
Hugues Fruchet authored
DCMI can capture 5Mp raw frames, increase limit accordingly. Signed-off-by:
-
Niklas Söderlund authored
Prepare for adding a new IOCTL VIDIOC_SUBDEV_ENUMSTD which would enumerate the standards for a subdevice by breaking out the code which could be shared between the video and subdevice versions of this IOCTL. Signed-off-by:
Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by:
-
Jacopo Mondi authored
Use the new renesas-ceu camera driver in ap325rxa board file instead of the soc_camera based sh_mobile_ceu_camera driver. Get rid of soc_camera specific components, and register CEU0 with a single video sensor (ov7725). Memory for the CEU video buffers is now reserved with membocks APIs and need to be declared as dma_coherent during machine initialization to remove that architecture specific part from CEU driver. The ap325rxa board file registers another camera (ncm03j) for which I found no driver in mainline kernel version, and that was configured/probed by sending i2c messages (of 'magic blobs) from the board file itself. I removed the sensor registration from this new version as it used soc_camera components that will be later removed. While at there update license to SPDX header and sort headers alphabetically. Compile tested only. Signed-off-by:
Jacopo Mondi <jacopo+renesas@jmondi.org> Signed-off-by:
-
Jacopo Mondi authored
Use the new renesas-ceu camera driver is ms7724se board file instead of the soc_camera based sh_mobile_ceu_camera driver. Get rid of soc_camera specific components, and register CEU0 and CEU1 with no active video subdevices. Memory for the CEU video buffers is now reserved with membocks APIs and need to be declared as dma_coherent during machine initialization to remove that architecture specific part from CEU driver. While at there update license to SPDX header and sort headers alphabetically. No need to udapte the clock source names, as commit c2f9b05f ("media: arch: sh: ecovec: Use new renesas-ceu camera driver") already updated it to the new ceu driver name for all SH7724 boards (possibly breaking ms7724se before this commit). Compile tested only. Signed-off-by:
-
Jacopo Mondi authored
Use the new renesas-ceu camera driver in kfr2r09 board file instead of the soc_camera based sh_mobile_ceu_camera driver. Get rid of soc_camera specific components, and move clk and gpio handling away from board file, registering the clock source and the enable gpios for driver consumption. Memory for the CEU video buffers is now reserved with membocks APIs, and need to be declared as dma_coherent during machine initialization to remove that architecture specific part from CEU driver. While at there update license to SPDX header and sort headers alphabetically. No need to udapte the clock source names, as commit c2f9b05f ("media: arch: sh: ecovec: Use new renesas-ceu camera driver") already updated it to the new ceu driver name for all SH7724 boards (possibly breaking kfr2r09 before this commit). Compile tested only. Signed-off-by:
-
Jacopo Mondi authored
Remove soc_camera framework dependencies from rj54n1 sensor driver. - Handle clock - Handle GPIOs (named 'powerup' and 'enable') - Register the async subdevice - Remove g/s_mbus_config as they're deprecated. - Adjust build system - List the driver as maintained for 'Odd Fixes' as I don't have HW to test. This commits does not remove the original soc_camera based driver. Compiled tested only. Signed-off-by:
-
Jacopo Mondi authored
Copy the soc_camera based driver in v4l2 sensor driver directory. This commit just copies the original file without modifying it. No modification to KConfig and Makefile as soc_camera framework dependencies need to be removed first in next commit. Signed-off-by:
-
Niklas Söderlund authored
Add the SoC specific information for Renesas r8a77965. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Niklas Söderlund authored
When starting the VIN capture procedure we are not guaranteed that the first buffer written to is VnMB1 to which we assigned the first buffer queued. This is problematic for two reasons. Buffers might not be dequeued in the same order they where queued for capture. Future features planed for the VIN driver is support for outputting frames in SEQ_TB/BT format and to do that it's important that capture starts from the first buffer slot, VnMB1. We are guaranteed that capturing always happens in sequence (VnMB1 -> VnMB2 -> VnMB3 -> VnMB1). So drop up to two frames when starting capturing so that the driver always returns buffers in the same order they are queued and prepare for SEQ_TB/BT output. Signed-off-by:
-
Niklas Söderlund authored
The style for referring to ports and endpoint are wrong. Refer to them using lowercase and a unit address, port@x and endpoint@x. Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Reviewed-by:
Rob Herring <robh@kernel.org> Reviewed-by:
Simon Horman <horms+renesas@verge.net.au> Reviewed-by:
-
Niklas Söderlund authored
Signed-off-by:
-
Simon Horman authored
The example vin port node does not have an address and thus does not need address-cells or address size-properties. Signed-off-by:
-
Pavel Machek authored
Add support for LM3559, as found in Motorola Droid 4 phone, for example. SW interface seems to be identical. Signed-off-by:
Pavel Machek <pavel@ucw.cz> Signed-off-by:
-
Gabriel Fanelli authored
This patch fixes the checkpatch.pl issue: CHECK: Alignment should match open parenthesis Signed-off-by:
Gabriel Fanelli <gabrielfanelli61@gmail.com> Signed-off-by:
-
Jacopo Mondi authored
Add support for YUYV permutations, passing down to the subdevice the media bus format with components ordering that reflect the output pixel format one. Signed-off-by:
-
