flush_scheduled_work() is on its way out.  Remove its usage from
iseries_veth.

* Cancelling a delayed work, queueing it for immediate execution if
  cancelled and then waiting for completion can be done by simply
  calling flush_delayed_work_sync().

* Explicitly cancel cnx->statemachine_wq on module unload.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Santiago Leon <santil@linux.vnet.ibm.com>
Cc: netdev@vger.kernel.org

Directly cancel port->reset_task from ehea_shutdown_single_port()
instead.  As this cancels the work for each port on driver detach,
flushing system_wq from ehea_remove() or ehea_module_exit() is no
longer necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Breno Leitao <leitao@linux.vnet.ibm.com>
Cc: netdev@vger.kernel.org

ehea_rereg_mr_task is not used.  Remove it and drop @work parameter
from ehea_rereg_mrs().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Breno Leitao <leitao@linux.vnet.ibm.com>
Cc: netdev@vger.kernel.org

flush_scheduled_work() is on its way out.  This patch contains simple
conversions to replace flush_scheduled_work() usage with direct
cancels and flushes.

Directly cancel the used works on driver detach and flush them in
other cases.

The conversions are mostly straight forward and the only dangers are,

* Forgetting to cancel/flush one or more used works.

* Cancelling when a work should be flushed (ie. the work must be
  executed once scheduled whether the driver is detaching or not).

I've gone over the changes multiple times but it would be much
appreciated if you can review with the above points in mind.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: Divy Le Ray <divy@chelsio.com>
Cc: e1000-devel@lists.sourceforge.net
Cc: Vasanthy Kolluri <vkolluri@cisco.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Andrew Gallatin <gallatin@myri.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: Ramkrishna Vepa <ramkrishna.vepa@exar.com>
Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: netdev@vger.kernel.org

janz-ican3, sh_eth, skge and vxge don't use workqueue at all and there
is no reason to flush the system_wq.  Drop flush_scheduled_work()
calls and references to workqueue.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Ramkrishna Vepa <ramkrishna.vepa@exar.com>
Cc: Sivakumar Subramani <sivakumar.subramani@exar.com>
Cc: Sreenivasa Honnur <sreenivasa.honnur@exar.com>
Cc: Jon Mason <jon.mason@exar.com>
Cc: netdev@vger.kernel.org

The driver global au_macs[] is unused in the entire kernel tree,
so remove it.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s2io: Using static const generally increases object text and decreases data size. It also generally decreases overall object size.

text	   data	    bss	    dec	    hex	filename
 109387	    389	  24432	 134208	  20c40	drivers/net/s2io.o.old
 109358	    389	  24432	 134179	  20c23	drivers/net/s2io.o.new
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update Driver Version
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Put immutable data in read/only section.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

modparm rx_ring_sz can be set to be greater than the maximum allowable
number of blocks.  This results in an array overrun when probing the
driver, and causes memory corruption.

Also, the MAX_RX_DESC_1 multiply the max number of rings by max number
of blocker per ring by 127, but the driver does the same calculation
with 127+1.  This results in the possibility of the value being set
being larger than the maximum allowable value.

Finally, clean-up the s2io_ethtool_gringparam code to be more
intuitive.
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

New adapters will have part numbers stored in string format rather than
simple hex format. This function will read part number formats in either
hex or string.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Adding this default case resolves the issue.

v2- Removed "break" in default case based on feedback
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Correct error messages when setting up Rx resources and when checking
module parameters.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

tx_desc can be dereferenced as a null pointer when count is passed in
as 0.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Provide support to e1000e for displaying the new format of the PBA found
in the EEPROM.  The unique PBA identifier is no longer restricted to
hexadecimal numbers and must now be read and displayed as a string.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

During init, reading the 2 PHY ID registers back-to-back in the default
fast mode could return invalid data (all F's) and in slow mode could
return data to the second read the data from the first read.  To resolve
the issue in fast mode, set to slow mode before any PHY accesses; to
resolve the issue in slow mode, put in a delay for every 82579 PHY access.
Since this PHY is currently only paired with the pch2lan MAC and the PHY
type is not known before the first PHY access which can fail this way,
check for this based on MAC-type.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The LPLU (Low Power Link Up) and Gigabit Disable bits (a.k.a. OEM bits)
were being configured incorrectly when device goes to D3 state.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When link partner is sending continuous Config symbols, the 82571 Serdes
FIFO can overflow resulting in Invalid bit getting set.  To resolve this,
if Sync and Config bits are both 1 ignore the Invalid bit and restart
auto-negotiation.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The workaround function e1000_configure_k1_pchlan() assumes the h/w
semaphore is already acquired.  This was originally missed when setting up
the part for the ethtool loopback test.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Increasing the transmit fifo by 4K (by decreasing the receive fifo size
specified in .pba by the same amount) increases Tx performance.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

On certain 82571-based mezzanine NICs in some blade servers, the ethtool
link test can fail due to the serdes_has_link flag not set correctly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The kernel goes BUG() at the time 'ethtool -p eth0 3' comes
back, which is due to adapter->led_blink_task initialized
several times.  At the time it is still running this results
in a corrupted task_list of the associated workqueue.

The fix is to move the workqueue initialization to the
probe function instead.
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Some minor cleanup to use string calls that use bound checks just to
be extra safe.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

commit f62bbb5e
ixgbe: Update ixgbe to use new vlan accleration.

removed ETH_FLAG_NTUPLE from the supported flags.

This patch puts it back on to allow for setting ntuple via ethtool.

CC: Jesse Gross <jesse@nicira.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch enables X540 hardware to use it's own set of support
functions.  This is useful as it has no need of SFP+ support.  A
couple minor bugs with the eeprom semaphore were also cleaned up.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The existing PHY ID for X540 was from early production hardware and
is no longer correct.  This patch corrects that.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Based on a patch from Jesse Gross.

Enable vlan tag insertion even when vlan group is not configured.

For ixgb HW both CTRL0.VME and VLE bit in the Tx descriptor need to be set
in order to enable HW acceleration.

Introduced separate functions for enabling/disabling of vlan tag stripping
similar to ixgbe.

CC: Jesse Gross <jesse@nicira.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Based on work by Joe Perches <joe@perches.com>

Using static const to decrease data and overall object size.

CC: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>

Dean noticed that 'err' wasn't being set when the "goto err_dma"
statement is executed in the following hunk from the commit. It's value
will be zero as a result of a successful call to e1000_init_hw_struct().

This patch changes the error condition to be correctly propagated.

CC: stable@kernel.org
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Update with Intel Wired Ethernet public git trees.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Update Intel Wired LAN ixgbevf documentation.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Update Intel Wired LAN ixgbe documentation.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Update Intel Wired LAN igbvf documentation.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Update Intel Wired LAN igb documentation.

v2- Updated the ethtool support link, removed the LRO section and
    anti-spoofing sections.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Update Intel Wired LAN e1000e documentation.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Update Intel Wired LAN e1000 documentation.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: David S. Miller <davem@davemloft.net>

This patch provides the debugfs facility to the bonding driver.
The "bonding" directory is created in the debugfs root and directories of
each bonding interface (like bond0, bond1...) are created in that.

 # mount -t debugfs none /sys/kernel/debug

 # ls /sys/kernel/debug/bonding
 bond0  bond1
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David Wang <dwang2@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>