The same fix in Commit dbe17307 ("bridge: fix netconsole
setup over bridge") is also needed for team driver.

While at it, remove the unnecessary parameter *team from
team_port_enable_netpoll().

v1->v2:
  - fix it in a better way, as does bridge.

Fixes: 0fb52a27 ("team: cleanup netpoll clode")
Reported-by: João Avelino Bellomo Filho <jbellomo@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

aTom Lendacky says:

====================
amd-xgbe: AMD XGBE driver fixes 2018-04-23

This patch series addresses some issues in the AMD XGBE driver.

The following fixes are included in this driver update series:

- Improve KR auto-negotiation and training (2 patches)
  - Add pre and post auto-negotiation hooks
  - Use the pre and post auto-negotiation hooks to disable CDR tracking
    during auto-negotiation page exchange in KR mode
- Check for SFP tranceiver signal support and only use the signal if the
  SFP indicates that it is supported

This patch series is based on net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The SFP eeprom indicates the transceiver signals (Rx LOS, Tx Fault, etc.)
that it supports.  Update the driver to include checking the eeprom data
when deciding whether to use a transceiver signal.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update xgbe-phy-v2.c to make use of the auto-negotiation (AN) phy hooks
to improve the ability to successfully complete Clause 73 AN when running
at 10gbps.  Hardware can sometimes have issues with CDR lock when the
AN DME page exchange is being performed.

The AN and KR training hooks are used as follows:
- The pre AN hook is used to disable CDR tracking in the PHY so that the
  DME page exchange can be successfully and consistently completed.
- The post KR training hook is used to re-enable the CDR tracking so that
  KR training can successfully complete.
- The post AN hook is used to check for an unsuccessful AN which will
  increase a CDR tracking enablement delay (up to a maximum value).

Add two debugfs entries to allow control over use of the CDR tracking
workaround.  The debugfs entries allow the CDR tracking workaround to
be disabled and determine whether to re-enable CDR tracking before or
after link training has been initiated.

Also, with these changes the receiver reset cycle that is performed during
the link status check can be performed less often.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add hooks to the driver auto-negotiation (AN) flow to allow the different
phy implementations to perform any steps necessary to improve AN.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We must validate sockaddr_len, otherwise userspace can pass fewer data
than we expect and we end up accessing invalid data.

Fixes: 224cf5ad ("ppp: Move the PPP drivers")
Reported-by: syzbot+4f03bdf92fdf9ef5ddab@syzkaller.appspotmail.com
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check sockaddr_len before dereferencing sp->sa_protocol, to ensure that
it actually points to valid data.

Fixes: fd558d18 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts")
Reported-by: syzbot+a70ac890b23b1bf29f5c@syzkaller.appspotmail.com
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

If WOL event happened once, the LED[2] interrupt pin will not be
cleared unless we read the CSISR register. If interrupts are in use,
the normal interrupt handling will clear the WOL event. Let's clear the
WOL event before enabling it if !phy_interrupt_is_valid().
Signed-off-by: Jingju Hou <Jingju.Hou@synaptics.com>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter/IPVS fixes for net

The following patchset contains Netfilter/IPVS fixes for your net tree,
they are:

1) Fix SIP conntrack with phones sending session descriptions for different
   media types but same port numbers, from Florian Westphal.

2) Fix incorrect rtnl_lock mutex logic from IPVS sync thread, from Julian
   Anastasov.

3) Skip compat array allocation in ebtables if there is no entries, also
   from Florian.

4) Do not lose left/right bits when shifting marks from xt_connmark, from
   Jack Ma.

5) Silence false positive memleak in conntrack extensions, from Cong Wang.

6) Fix CONFIG_NF_REJECT_IPV6=m link problems, from Arnd Bergmann.

7) Cannot kfree rule that is already in list in nf_tables, switch order
   so this error handling is not required, from Florian Westphal.

8) Release set name in error path, from Florian.

9) include kmemleak.h in nf_conntrack_extend.c, from Stepheh Rothwell.

10) NAT chain and extensions depend on NF_TABLES.

11) Out of bound access when renaming chains, from Taehee Yoo.

12) Incorrect casting in xt_connmark leads to wrong bitshifting.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

KMSAN reported use of uninit-value that I tracked to lack
of proper size check on RTA_TABLE attribute.

I also believe RTA_PREFSRC lacks a similar check.

Fixes: 86872cb5 ("[IPv6] route: FIB6 configuration using struct fib6_config")
Fixes: c3968a85 ("ipv6: RTA_PREFSRC support for ipv6 route source address selection")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After Commit 8a8efa22 ("bonding: sync netpoll code with bridge"), it
would set slave_dev npinfo in slave_enable_netpoll when enslaving a dev
if bond->dev->npinfo was set.

However now slave_dev npinfo is set with bond->dev->npinfo before calling
slave_enable_netpoll. With slave_dev npinfo set, __netpoll_setup called
in slave_enable_netpoll will not call slave dev's .ndo_netpoll_setup().
It causes that the lower dev of this slave dev can't set its npinfo.

One way to reproduce it:

  # modprobe bonding
  # brctl addbr br0
  # brctl addif br0 eth1
  # ifconfig bond0 192.168.122.1/24 up
  # ifenslave bond0 eth2
  # systemctl restart netconsole
  # ifenslave bond0 br0
  # ifconfig eth2 down
  # systemctl restart netconsole

The netpoll won't really work.

This patch is to remove that slave_dev npinfo setting in bond_enslave().

Fixes: 8a8efa22 ("bonding: sync netpoll code with bridge")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The old code reads the "opsize" variable from out-of-bounds memory (first
byte behind the segment) if a broken TCP segment ends directly after an
opcode that is neither EOL nor NOP.

The result of the read isn't used for anything, so the worst thing that
could theoretically happen is a pagefault; and since the physmap is usually
mostly contiguous, even that seems pretty unlikely.

The following C reproducer triggers the uninitialized read - however, you
can't actually see anything happen unless you put something like a
pr_warn() in tcp_parse_md5sig_option() to print the opsize.

====================================
#define _GNU_SOURCE
#include <arpa/inet.h>
#include <stdlib.h>
#include <errno.h>
#include <stdarg.h>
#include <net/if.h>
#include <linux/if.h>
#include <linux/ip.h>
#include <linux/tcp.h>
#include <linux/in.h>
#include <linux/if_tun.h>
#include <err.h>
#include <sys/types.h>
#include <sys/stat.h>
#include <fcntl.h>
#include <string.h>
#include <stdio.h>
#include <unistd.h>
#include <sys/ioctl.h>
#include <assert.h>

void systemf(const char *command, ...) {
  char *full_command;
  va_list ap;
  va_start(ap, command);
  if (vasprintf(&full_command, command, ap) == -1)
    err(1, "vasprintf");
  va_end(ap);
  printf("systemf: <<<%s>>>\n", full_command);
  system(full_command);
}

char *devname;

int tun_alloc(char *name) {
  int fd = open("/dev/net/tun", O_RDWR);
  if (fd == -1)
    err(1, "open tun dev");
  static struct ifreq req = { .ifr_flags = IFF_TUN|IFF_NO_PI };
  strcpy(req.ifr_name, name);
  if (ioctl(fd, TUNSETIFF, &req))
    err(1, "TUNSETIFF");
  devname = req.ifr_name;
  printf("device name: %s\n", devname);
  return fd;
}

#define IPADDR(a,b,c,d) (((a)<<0)+((b)<<8)+((c)<<16)+((d)<<24))

void sum_accumulate(unsigned int *sum, void *data, int len) {
  assert((len&2)==0);
  for (int i=0; i<len/2; i++) {
    *sum += ntohs(((unsigned short *)data)[i]);
  }
}

unsigned short sum_final(unsigned int sum) {
  sum = (sum >> 16) + (sum & 0xffff);
  sum = (sum >> 16) + (sum & 0xffff);
  return htons(~sum);
}

void fix_ip_sum(struct iphdr *ip) {
  unsigned int sum = 0;
  sum_accumulate(&sum, ip, sizeof(*ip));
  ip->check = sum_final(sum);
}

void fix_tcp_sum(struct iphdr *ip, struct tcphdr *tcp) {
  unsigned int sum = 0;
  struct {
    unsigned int saddr;
    unsigned int daddr;
    unsigned char pad;
    unsigned char proto_num;
    unsigned short tcp_len;
  } fakehdr = {
    .saddr = ip->saddr,
    .daddr = ip->daddr,
    .proto_num = ip->protocol,
    .tcp_len = htons(ntohs(ip->tot_len) - ip->ihl*4)
  };
  sum_accumulate(&sum, &fakehdr, sizeof(fakehdr));
  sum_accumulate(&sum, tcp, tcp->doff*4);
  tcp->check = sum_final(sum);
}

int main(void) {
  int tun_fd = tun_alloc("inject_dev%d");
  systemf("ip link set %s up", devname);
  systemf("ip addr add 192.168.42.1/24 dev %s", devname);

  struct {
    struct iphdr ip;
    struct tcphdr tcp;
    unsigned char tcp_opts[20];
  } __attribute__((packed)) syn_packet = {
    .ip = {
      .ihl = sizeof(struct iphdr)/4,
      .version = 4,
      .tot_len = htons(sizeof(syn_packet)),
      .ttl = 30,
      .protocol = IPPROTO_TCP,
      /* FIXUP check */
      .saddr = IPADDR(192,168,42,2),
      .daddr = IPADDR(192,168,42,1)
    },
    .tcp = {
      .source = htons(1),
      .dest = htons(1337),
      .seq = 0x12345678,
      .doff = (sizeof(syn_packet.tcp)+sizeof(syn_packet.tcp_opts))/4,
      .syn = 1,
      .window = htons(64),
      .check = 0 /*FIXUP*/
    },
    .tcp_opts = {
      /* INVALID: trailing MD5SIG opcode after NOPs */
      1, 1, 1, 1, 1,
      1, 1, 1, 1, 1,
      1, 1, 1, 1, 1,
      1, 1, 1, 1, 19
    }
  };
  fix_ip_sum(&syn_packet.ip);
  fix_tcp_sum(&syn_packet.ip, &syn_packet.tcp);
  while (1) {
    int write_res = write(tun_fd, &syn_packet, sizeof(syn_packet));
    if (write_res != sizeof(syn_packet))
      err(1, "packet write failed");
  }
}
====================================

Fixes: cfb6eeb4 ("[TCP]: MD5 Signature Option (RFC2385) support.")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf 2018-04-21

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) Fix a deadlock between mm->mmap_sem and bpf_event_mutex when
   one task is detaching a BPF prog via perf_event_detach_bpf_prog()
   and another one dumping through bpf_prog_array_copy_info(). For
   the latter we move the copy_to_user() out of the bpf_event_mutex
   lock to fix it, from Yonghong.

2) Fix test_sock and test_sock_addr.sh failures. The former was
   hitting rlimit issues and the latter required ping to specify
   the address family, from Yonghong.

3) Remove a dead check in sockmap's sock_map_alloc(), from Jann.

4) Add generated files to BPF kselftests gitignore that were previously
   missed, from Anders.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Avoid using value stored in the login response buffer when
cleaning TX and RX buffer pools since these could be inconsistent
depending on the device state. Instead use the field in the driver's
private data that tracks the number of active pools.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexander Aring says:

====================
net: sched: ife: malformed ife packet fixes

As promised at netdev 2.2 tc workshop I am working on adding scapy support for
tdc testing. It is still work in progress. I will submit the patches to tdc
later (they are not in good shape yet). The good news is I have been able to
find bugs which normal packet testing would not be able to find.
With fuzzy testing I was able to craft certain malformed packets that IFE
action was not able to deal with. This patch set fixes those bugs.

changes since v4:
 - use pskb_may_pull before pointer assign

changes since v3:
 - use pskb_may_pull

changes since v2:
 - remove inline from __ife_tlv_meta_valid
 - add const to cast to meta_tlvhdr
 - add acked and reviewed tags
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch checks if sk buffer is available to dererence ife header. If
not then NULL will returned to signal an malformed ife packet. This
avoids to crashing the kernel from outside.
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Reviewed-by: Yotam Gigi <yotam.gi@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is currently no handling to check on a invalid tlv length. This
patch adds such handling to avoid killing the kernel with a malformed
ife packet.
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Reviewed-by: Yotam Gigi <yotam.gi@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to record stats for received metadata that we dont know how
to process. Have find_decode_metaid() return -ENOENT to capture this.
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Reviewed-by: Yotam Gigi <yotam.gi@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

struct sock's sk_rcvtimeo is initialized to
LONG_MAX/MAX_SCHEDULE_TIMEOUT in sock_init_data. Calling
mod_delayed_work with a timeout of LONG_MAX causes spurious execution of
the work function. timer->expires is set equal to jiffies + LONG_MAX.
When timer_base->clk falls behind the current value of jiffies,
the delta between timer_base->clk and jiffies + LONG_MAX causes the
expiration to be in the past. Returning early from strp_start_timer if
timeo == LONG_MAX solves this problem.

Found while testing net/tls_sw recv path.

Fixes: 43a0c675 ("strparser: Stream parser for messages")
Reviewed-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Doron Roberts-Kedes <doronrk@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case of seg6 in encap mode, seg6_do_srh_encap() calls set_tun_src()
in order to set the src addr of outer IPv6 header.

The net_device is required for set_tun_src(). However calling ip6_dst_idev()
on dst_entry in case of IPv4 traffic results on the following bug.

Using just dst->dev should fix this BUG.

[  196.242461] BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
[  196.242975] PGD 800000010f076067 P4D 800000010f076067 PUD 10f060067 PMD 0
[  196.243329] Oops: 0000 [#1] SMP PTI
[  196.243468] Modules linked in: nfsd auth_rpcgss nfs_acl nfs lockd grace fscache sunrpc crct10dif_pclmul crc32_pclmul ghash_clmulni_intel pcbc aesni_intel aes_x86_64 crypto_simd cryptd input_leds glue_helper led_class pcspkr serio_raw mac_hid video autofs4 hid_generic usbhid hid e1000 i2c_piix4 ahci pata_acpi libahci
[  196.244362] CPU: 2 PID: 1089 Comm: ping Not tainted 4.16.0+ #1
[  196.244606] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[  196.244968] RIP: 0010:seg6_do_srh_encap+0x1ac/0x300
[  196.245236] RSP: 0018:ffffb2ce00b23a60 EFLAGS: 00010202
[  196.245464] RAX: 0000000000000000 RBX: ffff8c7f53eea300 RCX: 0000000000000000
[  196.245742] RDX: 0000f10000000000 RSI: ffff8c7f52085a6c RDI: ffff8c7f41166850
[  196.246018] RBP: ffffb2ce00b23aa8 R08: 00000000000261e0 R09: ffff8c7f41166800
[  196.246294] R10: ffffdce5040ac780 R11: ffff8c7f41166828 R12: ffff8c7f41166808
[  196.246570] R13: ffff8c7f52085a44 R14: ffffffffb73211c0 R15: ffff8c7e69e44200
[  196.246846] FS:  00007fc448789700(0000) GS:ffff8c7f59d00000(0000) knlGS:0000000000000000
[  196.247286] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  196.247526] CR2: 0000000000000000 CR3: 000000010f05a000 CR4: 00000000000406e0
[  196.247804] Call Trace:
[  196.247972]  seg6_do_srh+0x15b/0x1c0
[  196.248156]  seg6_output+0x3c/0x220
[  196.248341]  ? prandom_u32+0x14/0x20
[  196.248526]  ? ip_idents_reserve+0x6c/0x80
[  196.248723]  ? __ip_select_ident+0x90/0x100
[  196.248923]  ? ip_append_data.part.50+0x6c/0xd0
[  196.249133]  lwtunnel_output+0x44/0x70
[  196.249328]  ip_send_skb+0x15/0x40
[  196.249515]  raw_sendmsg+0x8c3/0xac0
[  196.249701]  ? _copy_from_user+0x2e/0x60
[  196.249897]  ? rw_copy_check_uvector+0x53/0x110
[  196.250106]  ? _copy_from_user+0x2e/0x60
[  196.250299]  ? copy_msghdr_from_user+0xce/0x140
[  196.250508]  sock_sendmsg+0x36/0x40
[  196.250690]  ___sys_sendmsg+0x292/0x2a0
[  196.250881]  ? _cond_resched+0x15/0x30
[  196.251074]  ? copy_termios+0x1e/0x70
[  196.251261]  ? _copy_to_user+0x22/0x30
[  196.251575]  ? tty_mode_ioctl+0x1c3/0x4e0
[  196.251782]  ? _cond_resched+0x15/0x30
[  196.251972]  ? mutex_lock+0xe/0x30
[  196.252152]  ? vvar_fault+0xd2/0x110
[  196.252337]  ? __do_fault+0x1f/0xc0
[  196.252521]  ? __handle_mm_fault+0xc1f/0x12d0
[  196.252727]  ? __sys_sendmsg+0x63/0xa0
[  196.252919]  __sys_sendmsg+0x63/0xa0
[  196.253107]  do_syscall_64+0x72/0x200
[  196.253305]  entry_SYSCALL_64_after_hwframe+0x3d/0xa2
[  196.253530] RIP: 0033:0x7fc4480b0690
[  196.253715] RSP: 002b:00007ffde9f252f8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
[  196.254053] RAX: ffffffffffffffda RBX: 0000000000000040 RCX: 00007fc4480b0690
[  196.254331] RDX: 0000000000000000 RSI: 000000000060a360 RDI: 0000000000000003
[  196.254608] RBP: 00007ffde9f253f0 R08: 00000000002d1e81 R09: 0000000000000002
[  196.254884] R10: 00007ffde9f250c0 R11: 0000000000000246 R12: 0000000000b22070
[  196.255205] R13: 20c49ba5e353f7cf R14: 431bde82d7b634db R15: 00007ffde9f278fe
[  196.255484] Code: a5 0f b6 45 c0 41 88 41 28 41 0f b6 41 2c 48 c1 e0 04 49 8b 54 01 38 49 8b 44 01 30 49 89 51 20 49 89 41 18 48 8b 83 b0 00 00 00 <48> 8b 30 49 8b 86 08 0b 00 00 48 8b 40 20 48 8b 50 08 48 0b 10
[  196.256190] RIP: seg6_do_srh_encap+0x1ac/0x300 RSP: ffffb2ce00b23a60
[  196.256445] CR2: 0000000000000000
[  196.256676] ---[ end trace 71af7d093603885c ]---

Fixes: 8936ef76 ("ipv6: sr: fix NULL pointer dereference when setting encap source address")
Signed-off-by: Ahmed Abdelsalam <amsalam20@gmail.com>
Acked-by: David Lebrun <dlebrun@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For SOCK_ZAPPED socket, we don't need to care about llc->sap,
so we should just skip these refcount functions in this case.

Fixes: f7e43672 ("llc: hold llc_sap before release_sock()")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The CPDMA_TX_PRIORITY_MAP in real is vlan pcp field priority mapping
register and basically replaces vlan pcp field for tagged packets.
So, set it to be 1:1 mapping. Otherwise, it will cause unexpected
change of egress vlan tagged packets, like prio 2 -> prio 5.

Fixes: e05107e6 ("net: ethernet: ti: cpsw: add multi queue support")
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The connection timers of an llc sock could be still flying
after we delete them in llc_sk_free(), and even possibly
after we free the sock. We could just wait synchronously
here in case of troubles.

Note, I leave other call paths as they are, since they may
not have to wait, at least we can change them to synchronously
when needed.

Also, move the code to net/llc/llc_conn.c, which is apparently
a better place.

Reported-by: <syzbot+f922284c18ea23a8e457@syzkaller.appspotmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 0e0c3fee ("l2tp: hold reference on tunnels printed in pppol2tp proc file")
assumed that if pppol2tp_seq_stop() was called with non-NULL private
data (the 'v' pointer), then pppol2tp_seq_start() would not be called
again. It turns out that this isn't guaranteed, and overflowing the
seq_file's buffer in pppol2tp_seq_show() is a way to get into this
situation.

Therefore, pppol2tp_seq_stop() needs to reset pd->tunnel, so that
pppol2tp_seq_start() won't drop a reference again if it gets called.
We also have to clear pd->session, because the rest of the code expects
a non-NULL tunnel when pd->session is set.

The l2tp_debugfs module has the same issue. Fix it in the same way.

Fixes: 0e0c3fee ("l2tp: hold reference on tunnels printed in pppol2tp proc file")
Fixes: f726214d ("l2tp: hold reference on tunnels printed in l2tp/tunnels debugfs file")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Julian Wiedmann says:

====================
s390/qeth: fixes 2018-04-19

Please apply the following qeth fixes for 4.17. The common theme
seems to be error handling improvements in various areas of cmd IO.

Patches 1-3 should also go back to stable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

For z/VM NICs, qeth needs to consider which of the three CCW devices in
an MPC group it uses for requesting a managed MAC address.

On the Base device, the hypervisor returns a default MAC which is
pre-assigned when creating the NIC (this MAC is also returned by the
READ MAC primitive). Querying any other device results in the allocation
of an additional MAC address.

For consistency with READ MAC and to avoid using up more addresses than
necessary, it is preferable to use the NIC's default MAC. So switch the
the diag26c over to using a NIC's Read device, which should always be
identical to the Base device.

Fixes: ec61bd2f ("s390/qeth: use diag26c to get MAC address on L2")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Submitting a cmd IO request (usually on the WRITE device, but for IDX
also on the READ device) is currently done with ccw_device_start()
and a manual timeout in the caller.
On timeout, the caller cleans up the related resources (eg. IO buffer).
But 1) the IO might still be active and utilize those resources, and
    2) when the IO completes, qeth_irq() will attempt to clean up the
       same resources again.

Instead of introducing additional resource locking, switch to
ccw_device_start_timeout() to ensure IO termination after timeout, and
let the IRQ handler alone deal with cleaning up after a request.

This also removes a stray write->irq_pending reset from
clear_ipacmd_list(). The routine doesn't terminate any pending IO on
the WRITE device, so this should be handled properly via IO timeout
in the IRQ handler.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When changing the MAC address on a L2 qeth device, current code first
unregisters the old address, then registers the new one.
If HW rejects the new address (or the IO fails), the device ends up with
no operable address at all.

Re-order the code flow so that the old address only gets dropped if the
new address was registered successfully. While at it, add logic to catch
some corner-cases.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Creating the global workqueue during driver init may fail, deal with it.
Also, destroy the created workqueue on any subsequent error.

Fixes: 0f54761d ("qeth: Support VEPA mode")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For control IO, qeth currently tracks the index of the buffer that it
expects to complete the next IO on each qeth_channel. If the channel
presents an IRQ while this buffer has not yet completed, no completion
processing for _any_ completed buffer takes place.
So if the 'next buffer' is skipped for any sort of reason* (eg. when it
is released due to error conditions, before the IO is started), the
buffer obviously won't switch to PROCESSED until it is eventually
allocated for a _different_ IO and completes.
Until this happens, all completion processing on that channel stalls
and pending requests possibly time out.

As a fix, remove the whole 'next buffer' logic and simply process any
IO buffer right when it completes. A channel will never have more than
one IO pending, so there's no risk of processing out-of-sequence.

*Note: currently just one location in the code really handles this problem,
       by advancing the 'next' index manually.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure to check both return code fields before(!) processing the
command response. Otherwise we risk operating on invalid data.

This matches an earlier fix for SETASSPARMS commands, see
commit ad3cbf61 ("s390/qeth: fix error handling in checksum cmd callback").
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove dead code that bails on `attr->value_size > KMALLOC_MAX_SIZE` - the
previous check already bails on `attr->value_size != 4`.
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Pull thermal fixes from Eduardo Valentin:
 "A couple of fixes for the thermal subsystem"

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
  dt-bindings: thermal: Remove "cooling-{min|max}-level" properties
  dt-bindings: thermal: remove no longer needed samsung thermal properties

Pull MMC fixes from Ulf Hansson:
 "A couple of MMC host fixes:

   - sdhci-pci: Fixup tuning for AMD for eMMC HS200 mode

   - renesas_sdhi_internal_dmac: Avoid data corruption by limiting
     DMA RX"

* tag 'mmc-v4.17-3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: renesas_sdhi_internal_dmac: limit DMA RX for old SoCs
  mmc: sdhci-pci: Only do AMD tuning for HS200

Pull MD fixes from Shaohua Li:
 "Three small fixes for MD:

   - md-cluster fix for faulty device from Guoqing

   - writehint fix for writebehind IO for raid1 from Mariusz

   - a live lock fix for interrupted recovery from Yufen"

* tag 'md/4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
  raid1: copy write hint from master bio to behind bio
  md/raid1: exit sync request if MD_RECOVERY_INTR is set
  md-cluster: don't update recovery_offset for faulty device

In do_mount() when the MS_* flags are being converted to MNT_* flags,
MS_RDONLY got accidentally convered to SB_RDONLY.

Undo this change.

Fixes: e462ec50 ("VFS: Differentiate mount flags (MS_*) from internal superblock flags")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

AFS server records get removed from the net->fs_servers tree when
they're deleted, but not from the net->fs_addresses{4,6} lists, which
can lead to an oops in afs_find_server() when a server record has been
removed, for instance during rmmod.

Fix this by deleting the record from the by-address lists before posting
it for RCU destruction.

The reason this hasn't been noticed before is that the fileserver keeps
probing the local cache manager, thereby keeping the service record
alive, so the oops would only happen when a fileserver eventually gets
bored and stops pinging or if the module gets rmmod'd and a call comes
in from the fileserver during the window between the server records
being destroyed and the socket being closed.

The oops looks something like:

  BUG: unable to handle kernel NULL pointer dereference at 000000000000001c
  ...
  Workqueue: kafsd afs_process_async_call [kafs]
  RIP: 0010:afs_find_server+0x271/0x36f [kafs]
  ...
  Call Trace:
   afs_deliver_cb_init_call_back_state3+0x1f2/0x21f [kafs]
   afs_deliver_to_call+0x1ee/0x5e8 [kafs]
   afs_process_async_call+0x5b/0xd0 [kafs]
   process_one_work+0x2c2/0x504
   worker_thread+0x1d4/0x2ac
   kthread+0x11f/0x127
   ret_from_fork+0x24/0x30

Fixes: d2ddc776 ("afs: Overhaul volume and server record caching and fileserver rotation")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull networking fixes from David Miller:

 1) Unbalanced refcounting in TIPC, from Jon Maloy.

 2) Only allow TCP_MD5SIG to be set on sockets in close or listen state.
    Once the connection is established it makes no sense to change this.
    From Eric Dumazet.

 3) Missing attribute validation in neigh_dump_table(), also from Eric
    Dumazet.

 4) Fix address comparisons in SCTP, from Xin Long.

 5) Neigh proxy table clearing can deadlock, from Wolfgang Bumiller.

 6) Fix tunnel refcounting in l2tp, from Guillaume Nault.

 7) Fix double list insert in team driver, from Paolo Abeni.

 8) af_vsock.ko module was accidently made unremovable, from Stefan
    Hajnoczi.

 9) Fix reference to freed llc_sap object in llc stack, from Cong Wang.

10) Don't assume netdevice struct is DMA'able memory in virtio_net
    driver, from Michael S. Tsirkin.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (62 commits)
  net/smc: fix shutdown in state SMC_LISTEN
  bnxt_en: Fix memory fault in bnxt_ethtool_init()
  virtio_net: sparse annotation fix
  virtio_net: fix adding vids on big-endian
  virtio_net: split out ctrl buffer
  net: hns: Avoid action name truncation
  docs: ip-sysctl.txt: fix name of some ipv6 variables
  vmxnet3: fix incorrect dereference when rxvlan is disabled
  llc: hold llc_sap before release_sock()
  MAINTAINERS: Direct networking documentation changes to netdev
  atm: iphase: fix spelling mistake: "Tansmit" -> "Transmit"
  net: qmi_wwan: add Wistron Neweb D19Q1
  net: caif: fix spelling mistake "UKNOWN" -> "UNKNOWN"
  net: stmmac: Disable ACS Feature for GMAC >= 4
  net: mvpp2: Fix DMA address mask size
  net: change the comment of dev_mc_init
  net: qualcomm: rmnet: Fix warning seen with fill_info
  tun: fix vlan packet truncation
  tipc: fix infinite loop when dumping link monitor summary
  tipc: fix use-after-free in tipc_nametbl_stop
  ...

Pull vfs fixes from Al Viro:
 "Assorted fixes.

  Some of that is only a matter with fault injection (broken handling of
  small allocation failure in various mount-related places), but the
  last one is a root-triggerable stack overflow, and combined with
  userns it gets really nasty ;-/"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  Don't leak MNT_INTERNAL away from internal mounts
  mm,vmscan: Allow preallocating memory for register_shrinker().
  rpc_pipefs: fix double-dput()
  orangefs_kill_sb(): deal with allocation failures
  jffs2_kill_sb(): deal with failed allocations
  hypfs_kill_super(): deal with failed allocations

Merge tag 'ecryptfs-4.17-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs

Pull eCryptfs fixes from Tyler Hicks:
 "Minor cleanups and a bug fix to completely ignore unencrypted
  filenames in the lower filesystem when filename encryption is enabled
  at the eCryptfs layer"

* tag 'ecryptfs-4.17-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
  eCryptfs: don't pass up plaintext names when using filename encryption
  ecryptfs: fix spelling mistake: "cadidate" -> "candidate"
  ecryptfs: lookup: Don't check if mount_crypt_stat is NULL