- 19 Feb, 2012 40 commits
-
-
Vikas Chaudhary authored
Added support to post kernel host event to application using netlink interface. Signed-off-by:
Vikas Chaudhary <vikas.chaudhary@qlogic.com> Reviewed-by:
Mike Christie <michaelc@cs.wisc.edu> Signed-off-by:
James Bottomley <JBottomley@Parallels.com>
-
Vikas Chaudhary authored
Signed-off-by:
-
Lalit Chandivade authored
On ROM lock acquiring timeout failure, driver spews lot of warning messages in a for loop, remove the unwanted warning message to reduce kernel messages clutter. Signed-off-by:
Lalit Chandivade <lalit.chandivade@qlogic.com> Signed-off-by:
-
Manish Rangankar authored
In some configurations user may not have boot targets configured. In such cases the debug messages printed out by driver look like some kind of failure happening. However this could be a valid case, so modified the messages to appear as warning messages versus failure messages. Signed-off-by:
Manish Rangankar <manish.rangankar@qlogic.com> Signed-off-by:
-
Lalit Chandivade authored
qla4xxx_verify_boot_idx can falsely report a DDB to be boot target if ha->pri_ddb_idx and ha->sec_ddb_idx are not initialized correctly. What this could cause is if there is DDB entry in FLash at index 0, then qla4xxx_verify_boot_idx would return wrong result as ha->pri_ddb_idx is not set correctly. Fixed the qla4xxx_get_boot_info to set the ha->pri_ddb_idx and ha->sec_ddb_idx correctly. Signed-off-by:
-
Lalit Chandivade authored
Fix the un-necessary wait for completion of a sendtarget on an invalid DDB entry. The state of an invalid DDB entry is 0 (unassigned) This will also avoid the delays during system boot. Signed-off-by:
-
Vikas Chaudhary authored
This code initially added for FW debugging, we don't need this code now so taking it out. Signed-off-by:
-
Bhanu Prakash Gollapudi authored
While we wait for GPN_FT response, if the ctlr link goes down, the stack generates a completion for GPN_FT with error FC_EXCH_CLOSED, and reports a discovery error. Discovery is not retried in this case, and rightly so. However, the 'pending' flag stays set, which does not allow subsequent discovery to succeed as GPN_FT will never be issued. Fix it by clearing the pending flag when the discovery fails due to GPN_FT failure. Signed-off-by:
Bhanu Prakash Gollapudi <bprakash@broadcom.com> Signed-off-by:
Robert Love <robert.w.love@intel.com> Signed-off-by:
-
Bhanu Prakash Gollapudi authored
Adding and removing the host into the zone causes this panic. BUG: unable to handle kernel NULL pointer dereference at 00000000000000a0 IP: [<ffffffffa0491707>] fc_exch_recv+0xc57/0xe70 [libfc] Call Trace: [<ffffffffa050e04b>] bnx2fc_l2_rcv_thread+0x37b/0x430 [bnx2fc] [<ffffffffa050dcd0>] ? bnx2fc_l2_rcv_thread+0x0/0x430 [bnx2fc] [<ffffffff81090886>] kthread+0x96/0xa0 [<ffffffff8100c14a>] child_rip+0xa/0x20 [<ffffffff810907f0>] ? kthread+0x0/0xa0 [<ffffffff8100c140>] ? child_rip+0x0/0x20 During fc_exch_reset, the active exchanges are aborted and the exch is deleted. As part of processing ABTS response, due to 'ep' being NULL, any access to ep in fc_exch_recv_bls() causes this panic. Fixed to access 'ep' only if non-NULL. Reviewed-by:
Neerav Parikh <neerav.parikh@intel.com> Signed-off-by:
-
Robert Love authored
The reference counting was necessary on these instances because it was possible for NPIV ports to be destroyed after the N_Port. A previous patch ensures that all NPIV ports are destroyed before the N_Port making the need to track references on the interface unnecessary. Signed-off-by:
Ross Brattain <ross.b.brattain@intel.com> Signed-off-by:
-
Robert Love authored
Currently all port deletion is routed though the FCoE workqueue (fcoe_wq). When fc_remove_host is called on an N_Port (for example, from fcoe_destroy) the vports are queued into a FC Transport workqueue. fc_remove_host flushes that queue and each vport is passed to fcoe's fcoe_vport_destroy, which simply queues the associated fcoe_ports for later deletion. This queue cannot be flushed within the N_Ports destroy path because of circular locking issues. The result is that the NPIV ports are destroyed after the N_Port, which is reverse of how they are created. This quirk causes fcoe to keep references on the fcoe_interface shared by each of these ports (N_Port and NPIV). Changing the ordering such that NPIV ports are destroyed before the N_Port will allow us to remove reference counting on the fcoe_interface instances. This patch simply allows fcoe_vport_destory to destroy NPIV ports without deferring them to a workqueue context. This ensures that when fc_remove_host is called the NPIV ports will be destroyed first before the N_Port and allows reference counting on the fcoe's fcoe_interface to be remove in a later patch. Signed-off-by:
-
Robert Love authored
The label implies that it should be called when there is 'nomod.' I read that to mean that the module reference 'get' failed. However, it's only called when the module reference 'get' succeeded. I think it makes more sense to name the label, 'out_putmod' since it should be called when we need to 'put' the module reference taken in the routine before returning. Signed-off-by:
-
Neerav Parikh authored
Allow FDMI attributes to be exposed via the fc_host class object for the fcoe driver. Signed-off-by:
-
Robert Love authored
This is more of a debug statement. As a KERN_ERR we generate log entries anytime any netdev goes up or down, so when booting there are notification log entries for all system interfaces including 'lo'. This is too much. Let's just log when necessary. Signed-off-by:
-
Dave Jiang authored
This allows the controller to do WRITE_INSERT and READ_STRIP for SAS disks that support protection information. SAS disks must be formatted with protection information to use this feature via sg_format. sg3_utils-1.32 -- sg_format version 1.19 20110730 sg_format usage: sg_format --format --verbose --pinfo /dev/sda Acked-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
Dave Jiang <dave.jiang@intel.com> Signed-off-by:
Dan Williams <dan.j.williams@intel.com> Signed-off-by:
-
Arun Easi authored
Signed-off-by:
Arun Easi <arun.easi@qlogic.com> Signed-off-by:
Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by:
-
Arun Easi authored
Signed-off-by:
-
Arun Easi authored
Signed-off-by:
-
Arun Easi authored
A device logout sent in the delete path of a fcport would clear the port handle binding inside the firmware. This could lead to queued work items for the fcport, if any, getting incorrect results. This patch fixes the issue by checking for device name changes after a call to get port database. Signed-off-by:
-
Chad Dupuis authored
Add a field to the qla_hw_data struct to allow us to set the maximum number of fabric devices on a per adapter basis based on ISP type. [jejb: fix up missing rval = QLA_SUCCESS to prevent uninit var warning] Signed-off-by:
Giridhar Malavali <giridhar.malavali@qlogic.com> Signed-off-by:
-
Andrew Vasquez authored
Rather than continuously allocating and freeing swl within the discovery process, simply pre-allocate it the first time that it's needed, cache it through the rest of the lifecycle of the driver and free it at module unload. Signed-off-by:
Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by:
-
Joe Carnuccio authored
Signed-off-by:
Joe Carnuccio <joe.carnuccio@qlogic.com> Signed-off-by:
-
Chad Dupuis authored
Signed-off-by:
-
Chad Dupuis authored
Signed-off-by:
-
Giridhar Malavali authored
Signed-off-by:
-
Arun Easi authored
Signed-off-by:
-
Arun Easi authored
Signed-off-by:
-
Arun Easi authored
Signed-off-by:
-
Chad Dupuis authored
Signed-off-by:
-
Chad Dupuis authored
Signed-off-by:
-
Chad Dupuis authored
Signed-off-by:
-
Andrew Vasquez authored
Don't use default 30 second mailbox-command timeout for these serial requests, instead, limit the TMO to the standard 2*RATOV plus some fudge-factor. Signed-off-by:
-
Andrew Vasquez authored
During command failure/non-recognition, the upper-layer FC-transport expects the drivers to set job-reply->reply_payload_rcv_len. Do this in a consistent manner to avoid duplication. Signed-off-by:
-
Andrew Vasquez authored
During rport tear-down, make sure we do an implicit LOGO of the fcport in our firmware to try to clear any residual commands associated with that fcport. Signed-off-by:
-
Chad Dupuis authored
Make sure that all calls to ha->isp_ops->fabric_login() check the return value for failure. Signed-off-by:
-
Chad Dupuis authored
Signed-off-by:
-
Joe Carnuccio authored
When thermal temperature initially fails, return a blank string to the sysfs interface. This fixes the initial display of 0.00 followed by subsequent display of blank line; the initial 0.00 should have not displayed for cards that do not support thermal temperature. Signed-off-by:
-
Arun Easi authored
Instead of processing each RSCN individually, use only the name server results from the switch to tell the existance of a given fcport. Signed-off-by:
-
Joe Carnuccio authored
Signed-off-by:
-
Andrew Vasquez authored
The driver is logging a slew of 'good' status requests for ELS/CT passthrough commands. Change some log messages from: * ql_log() -> ql_dbg() * ql_log_info -> ql_dbg_user Signed-off-by:
-
