Now that sh64 has grown extended page flag support we finally have a free
bit for _PAGE_SPECIAL. Wire it up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

The ctrl_xxx routines are deprecated, switch over to the __raw_xxx
versions.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Now that all of the controllers have been fixed up, we can finally select
GENERIC_HARDIRQS_NO_DEPRECATED.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Presently the irq chip is found through the irq_desc, but as this is
going away convert over to an irq_data lookup instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

irq_32.c was updated for the new API, while irq_64.c was overlooked. This
syncs them up and gets things building again.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

The ctrl_xxx routines are deprecated, switch over to the __raw_xxx
versions.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

The ctrl_xxx routines are deprecated, switch over to the __raw_xxx
versions.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

The ctrl_xxx routines are deprecated, switch over to the __raw_xxx
versions.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

The ctrl_xxx routines are deprecated, switch over to the __raw_xxx
versions.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

The ctrl_xxx routines are deprecated, switch over to the __raw_xxx
versions.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

The introduction of MAX_PHYSMEM_BITS in to the initial cpuinfo struct
causes a build error when sparsemem is disabled and asm/sparsemem.h is
not brought in by other means. Include it explicitly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Now that the genirq code provides an IRQ bitmap of its own and the
necessary API to manipulate it, there's no need to keep our own version
around anymore.

In the process we kill off some unused IRQ reservation code, with future
users now having to tie in to the genirq API as normal.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Now that there's a HAVE_GENERIC_HARDIRQS, switch over.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Switch over to the new allocator functions.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

CPUs can be in either the legacy 29-bit or 32-bit physical addressing
modes. This follows the x86 approach of tracking the phys bits in cpuinfo
and exposing it to userspace through procfs.

This change was requested to permit kexec-tools to detect the physical
addressing mode in order to determine the appropriate address mangling.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

* 'for-next' of git://android.git.kernel.org/kernel/tegra:
  spi: tegra: fix error setting on timeout
  spi: add spi_tegra driver
  tegra: harmony: enable PCI Express
  tegra: add PCI Express support
  tegra: add PCI Express clocks
  [ARM] tegra: Add APB DMA support
  [ARM] tegra: Add cpufreq support
  [ARM] tegra: common: Update common clock init table
  [ARM] tegra: clock: Add dvfs support, bug fixes, and cleanups
  [ARM] tegra: Add support for reading fuses
  [ARM] tegra: gpio: Add suspend and wake support
  [ARM] tegra: pinmux: add safe values, move tegra2, add suspend
  [ARM] tegra: add suspend and mirror irqs to legacy controller
  [ARM] tegra: Add legacy irq support
  [ARM] tegra: update iomap

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin:
  Blackfin: fix inverted anomaly 05000481 logic
  Blackfin: drop unused irq_panic()/DEBUG_ICACHE_CHECK
  Blackfin: ppi/spi/twi headers: add missing __BFP undef
  Blackfin: update defconfigs
  Blackfin: bfin_twi.h: start a common TWI header
  netdev: bfin_mac: push settings to platform resources

avoids derefencing an uninitialized pointer

Change-Id: Icf528441ae481e9f6f5ddc0be32c7c217fa49701
Signed-off-by: Erik Gilling <konkers@android.com>

* 'next' of git://git.monstr.eu/linux-2.6-microblaze: (42 commits)
  microblaze: Fix build with make 3.82
  fbdev/xilinxfb: Microblaze driver support
  microblaze: Support C optimized lib functions for little-endian
  microblaze: Separate library optimized functions
  microblaze: Support timer on AXI lite
  microblaze: Add support for little-endian Microblaze
  microblaze: KGDB little endian support
  microblaze: Add PVR for endians plus detection
  net: emaclite: Add support for little-endian platforms
  microblaze: trivial: Add comment for AXI pvr
  microblaze: pci-common cleanup
  microblaze: Support early console on uart16550
  microblaze: Do not compile early console support for uartlite if is disabled
  microblaze: Setup early console dynamically
  microblaze: Rename all uartlite early printk functions
  microblaze: remove early printk uarlite console dependency from header
  microblaze: Remove additional compatible properties
  microblaze: Remove hardcoded asm instraction for PVR loading
  microblaze: Use static const char * const where possible
  microblaze: Define VMALLOC_START/END
  ...

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging: (24 commits)
  hwmon: lis3: Release resources in case of failure
  hwmon: lis3: Short explanations of platform data fields
  hwmon: lis3: Enhance lis3 selftest with IRQ line test
  hwmon: lis3: use block read to access data registers
  hwmon: lis3: Adjust fuzziness for 8 bit device
  hwmon: lis3: New parameters to platform data
  hwmon: lis3: restore axis enabled bits
  hwmon: lis3: Power on corrections
  hwmon: lis3: Update coordinates at polled device open
  hwmon: lis3: Cleanup interrupt handling
  hwmon: lis3: regulator control
  hwmon: lis3: pm_runtime support
  Kirkwood: add fan support for Network Space Max v2
  hwmon: add generic GPIO fan driver
  hwmon: (coretemp) fix reading of microcode revision (v2)
  hwmon: ({core, pkg, via-cpu}temp) remove unnecessary CONFIG_HOTPLUG_CPU ifdefs
  hwmon: (pkgtemp) align driver initialization style with coretemp
  hwmon: LTC4261 Hardware monitoring driver
  hwmon: (lis3) add axes module parameter for custom axis-mapping
  hwmon: (hp_accel) Add HP Mini 510x family support
  ...

In the MN10300 arch, we occasionally see an assertion being tripped in
alloc_cwqs() at the following line:

        /* just in case, make sure it's actually aligned */
  --->  BUG_ON(!IS_ALIGNED(wq->cpu_wq.v, align));
        return wq->cpu_wq.v ? 0 : -ENOMEM;

The values are:

        wa->cpu_wq.v => 0x902776e0
        align => 0x100

and align is calculated by the following:

        const size_t align = max_t(size_t, 1 << WORK_STRUCT_FLAG_BITS,
                                   __alignof__(unsigned long long));

This is because the pointer in question (wq->cpu_wq.v) loses some of its
lower bits to control flags, and so the object it points to must be
sufficiently aligned to avoid the need to use those bits for pointing to
things.

Currently, 4 control bits and 4 colour bits are used in normal
circumstances, plus a debugging bit if debugging is set.  This requires
the cpu_workqueue_struct struct to be at least 256 bytes aligned (or 512
bytes aligned with debugging).

PERCPU() alignment on MN13000, however, is only 32 bytes as set in
vmlinux.lds.S.  So we set this to PAGE_SIZE (4096) to match most other
arches and stick a comment in alloc_cwqs() for anyone else who triggers
the assertion.
Reported-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Mark Salter <msalter@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If lis3lv02d_init_device fails, HW resources were not released
properly. In case of failure call release_resources if available.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>

No one uses these MMRs so we didn't notice when the anomaly handling
logic was inverted.
Reported-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

This code was useful during early port development when our icache code
wasn't solid, but that ship has sailed long ago, and no code calls this
function anymore (irq_panic).  So punt it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Short documentation at kernel doc format.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>

Configure chip to data ready mode in selftest and count received
interrupts to see that interrupt line(s) are working.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>

Add optional blockread function to interface driver. If available
the chip driver uses it for data register access. For 12 bit device
it reads 6 bytes to get 3*16bit data. For 8 bit device it reads out
5 bytes since every second byte is dummy.
This optimizes bus usage and reduces number of operations and
interrupts needed for one data update.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>

Default fuziness is set smaller for 8 device.
In 12 bit device LSB is quite close to 1 mg
(mg = 1 / 1000 of earth gravity).
In 8bit device LSB is about 18 mg.
Set fuziness to 1 for 8 bit device.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>

Added default output data rate setting to platform data.
If default rate is 0, reset default value is used.
Added control for duration via platform data.
Added possibility to configure interrupts to trig on
both rising and falling edge. The lis3 WU unit can be
configured quite many ways and with some configurations it
is quite handy to get coordinate refresh when some
event trigs and when it reason goes away.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>