This implements Set extended scan param and set extended scan enable
commands and use it for start LE scan based on controller support.

The new features added in these commands are setting of new PHY for
scanning and setting of scan duration. Both features are disabled
for now, meaning only 1M PHY is set and scan duration is set to 0
which means that scanning will be done untill scan disable is called.

< HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 8
        Own address type: Random (0x01)
        Filter policy: Accept all advertisement (0x00)
        PHYs: 0x01
        Entry 0: LE 1M
          Type: Active (0x01)
          Interval: 11.250 msec (0x0012)
          Window: 11.250 msec (0x0012)
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Extended Scan Enable (0x08|0x0042) plen 6
        Extended scan: Enabled (0x01)
        Filter duplicates: Enabled (0x01)
        Duration: 0 msec (0x0000)
        Period: 0.00 sec (0x0000)
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Extended Scan Enable (0x08|0x0042) ncmd 2
        Status: Success (0x00)
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Introduce a helper hci_req_start_scan() which starts an LE
scan and call it from passive_Scan() and active_scan().
There is not functionality change in this patch.

This is basically done to enable extended scanning if the
controller supports which will be done in the subsequent
patch
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Nothing in tree use this header which seems a remains of a staging
driver.
This patch remove it.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Check for Resolv list supported by controller. So check the supported
commmand first before issuing this command i.e.,HCI_OP_LE_CLEAR_RESOLV_LIST

Before patch:
< HCI Command: LE Read White List... (0x08|0x000f) plen 0  #55 [hci0] 13.338168
> HCI Event: Command Complete (0x0e) plen 5                #56 [hci0] 13.338842
      LE Read White List Size (0x08|0x000f) ncmd 1
        Status: Success (0x00)
        Size: 25
< HCI Command: LE Clear White List (0x08|0x0010) plen 0    #57 [hci0] 13.339029
> HCI Event: Command Complete (0x0e) plen 4                #58 [hci0] 13.339939
      LE Clear White List (0x08|0x0010) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Read Resolving L.. (0x08|0x002a) plen 0  #59 [hci0] 13.340152
> HCI Event: Command Complete (0x0e) plen 5                #60 [hci0] 13.340952
      LE Read Resolving List Size (0x08|0x002a) ncmd 1
        Status: Success (0x00)
        Size: 25
< HCI Command: LE Read Maximum Dat.. (0x08|0x002f) plen 0  #61 [hci0] 13.341180
> HCI Event: Command Complete (0x0e) plen 12               #62 [hci0] 13.341898
      LE Read Maximum Data Length (0x08|0x002f) ncmd 1
        Status: Success (0x00)
        Max TX octets: 251
        Max TX time: 17040
        Max RX octets: 251
        Max RX time: 17040

After patch:
< HCI Command: LE Read White List... (0x08|0x000f) plen 0  #55 [hci0] 28.919131
> HCI Event: Command Complete (0x0e) plen 5                #56 [hci0] 28.920016
      LE Read White List Size (0x08|0x000f) ncmd 1
        Status: Success (0x00)
        Size: 25
< HCI Command: LE Clear White List (0x08|0x0010) plen 0    #57 [hci0] 28.920164
> HCI Event: Command Complete (0x0e) plen 4                #58 [hci0] 28.920873
      LE Clear White List (0x08|0x0010) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Read Resolving L.. (0x08|0x002a) plen 0  #59 [hci0] 28.921109
> HCI Event: Command Complete (0x0e) plen 5                #60 [hci0] 28.922016
      LE Read Resolving List Size (0x08|0x002a) ncmd 1
        Status: Success (0x00)
        Size: 25
< HCI Command: LE Clear Resolving... (0x08|0x0029) plen 0  #61 [hci0] 28.922166
> HCI Event: Command Complete (0x0e) plen 4                #62 [hci0] 28.922872
      LE Clear Resolving List (0x08|0x0029) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Read Maximum Dat.. (0x08|0x002f) plen 0  #63 [hci0] 28.923117
> HCI Event: Command Complete (0x0e) plen 12               #64 [hci0] 28.924030
      LE Read Maximum Data Length (0x08|0x002f) ncmd 1
        Status: Success (0x00)
        Max TX octets: 251
        Max TX time: 17040
        Max RX octets: 251
        Max RX time: 17040
Signed-off-by: Ankit Navik <ankit.p.navik@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

When the controller supports the Read LE Resolv List size feature, the
maximum list size are read and now stored.

Before patch:
< HCI Command: LE Read White List... (0x08|0x000f) plen 0  #55 [hci0] 17.979791
> HCI Event: Command Complete (0x0e) plen 5                #56 [hci0] 17.980629
      LE Read White List Size (0x08|0x000f) ncmd 1
        Status: Success (0x00)
        Size: 25
< HCI Command: LE Clear White List (0x08|0x0010) plen 0    #57 [hci0] 17.980786
> HCI Event: Command Complete (0x0e) plen 4                #58 [hci0] 17.981627
      LE Clear White List (0x08|0x0010) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Read Maximum Dat.. (0x08|0x002f) plen 0  #59 [hci0] 17.981786
> HCI Event: Command Complete (0x0e) plen 12               #60 [hci0] 17.982636
      LE Read Maximum Data Length (0x08|0x002f) ncmd 1
        Status: Success (0x00)
        Max TX octets: 251
        Max TX time: 17040
        Max RX octets: 251
        Max RX time: 17040

After patch:
< HCI Command: LE Read White List... (0x08|0x000f) plen 0  #55 [hci0] 13.338168
> HCI Event: Command Complete (0x0e) plen 5                #56 [hci0] 13.338842
      LE Read White List Size (0x08|0x000f) ncmd 1
        Status: Success (0x00)
        Size: 25
< HCI Command: LE Clear White List (0x08|0x0010) plen 0    #57 [hci0] 13.339029
> HCI Event: Command Complete (0x0e) plen 4                #58 [hci0] 13.339939
      LE Clear White List (0x08|0x0010) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Read Resolving L.. (0x08|0x002a) plen 0  #59 [hci0] 13.340152
> HCI Event: Command Complete (0x0e) plen 5                #60 [hci0] 13.340952
      LE Read Resolving List Size (0x08|0x002a) ncmd 1
        Status: Success (0x00)
        Size: 25
< HCI Command: LE Read Maximum Dat.. (0x08|0x002f) plen 0  #61 [hci0] 13.341180
> HCI Event: Command Complete (0x0e) plen 12               #62 [hci0] 13.341898
      LE Read Maximum Data Length (0x08|0x002f) ncmd 1
        Status: Success (0x00)
        Max TX octets: 251
        Max TX time: 17040
        Max RX octets: 251
        Max RX time: 17040
Signed-off-by: Ankit Navik <ankit.p.navik@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The USB completion callback does not disable interrupts while acquiring
the ->lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave variant of the locking primitives.

Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Without this patch we cannot turn on the Bluethooth adapter on HP
14-bs007la.

T:  Bus=01 Lev=02 Prnt=03 Port=00 Cnt=01 Dev#=  4 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0bda ProdID=b009 Rev= 2.00
S:  Manufacturer=Realtek
S:  Product=802.11n WLAN Adapter
S:  SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

After decompression of 6lowpan socket data, an IPv6 header is inserted
before the existing socket payload.  After this, we reset the
network_header value of the skb to account for the difference in payload
size from prior to decompression + the addition of the IPv6 header.

However, we fail to reset the mac_header value.

Leaving the mac_header value untouched here, can cause a calculation
error in net/packet/af_packet.c packet_rcv() function when an
AF_PACKET socket is opened in SOCK_RAW mode for use on a 6lowpan
interface.

On line 2088, the data pointer is moved backward by the value returned
from skb_mac_header().  If skb->data is adjusted so that it is before
the skb->head pointer (which can happen when an old value of mac_header
is left in place) the kernel generates a panic in net/core/skbuff.c
line 1717.

This panic can be generated by BLE 6lowpan interfaces (such as bt0) and
802.15.4 interfaces (such as lowpan0) as they both use the same 6lowpan
sources for compression and decompression.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
Acked-by: Alexander Aring <aring@mojatatu.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Edward Cree says:

====================
IP listification follow-ups

While working on IPv6 list processing, I found another bug in the IPv4
 version.  So this patch series has that fix, and the IPv6 version with
 both fixes incorporated.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Essentially the same as the ipv4 equivalents.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If we have an L3 master device, l3mdev_ip_rcv() will steal the skb, but
 we were returning NET_RX_SUCCESS from ip_rcv_finish_core() which meant
 that ip_list_rcv_finish() would keep it on the list.  Instead let's
 move the l3mdev_ip_rcv() call into the caller, so that our response to
 a steal can be different in the single packet path (return
 NET_RX_SUCCESS) and the list path (forget this packet and continue).

Fixes: 5fa12739 ("net: ipv4: listify ip_rcv_finish")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

Warning level 2 was used: -Wimplicit-fallthrough=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

Warning level 2 was used: -Wimplicit-fallthrough=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use 'chip_ver' rather than 'chip' to check if the card
is T5.

Fixes: e8d45292 ("cxgb4: clean up init_one")
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Variables adv and lpa are being assigned but are never used hence they
are redundant and can be removed.  Also remove the unncessary mii_reads
too.

Cleans up clang warnings:
warning: variable 'lpa' set but not used [-Wunused-but-set-variable]
warning: variable 'adv' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Geert Uytterhoeven says:

====================
net: ethernet: Miscellaneous Kconfig and Makefile cleanups

This patch series contains a few Kconfig and Makefile cleanups w.r.t.
Ethernet vendors.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Both SFC and SFC_FALCON depend on NET_VENDOR_SOLARFLARE, hence use the
latter to decide whether to descend into the sfc subdirectory.
Move the rule to descend into sfc/falcon to the sfc subdirectory.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The vendor guard Kconfig symbols for Cadence and Packet Engines use a
"NET_" prefix, while all other vendor guards use a "NET_VENDOR_"
prefix.  Hence make them consistent with the rest, and add the missing
trailing "S" for Packet Engines while at it.

As these options don't directly affect the kernel build, and default to
"y", this change has no impact on kernels built with existing
(def)configs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enabling NET_VENDOR_* Kconfig options does not directly affect the
kernel build.  Hence NET_VENDOR_AURORA should default to yes, like other
NET_VENDOR_* options.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

Variables consumer, cmd_desc, end_cnt and no_of_desc are being assigned
but are never used hence they are redundant and can be removed.

Cleans up clang warnings:
warning: variable 'consumer' set but not used [-Wunused-but-set-variable]
warning: variable 'cmd_desc' set but not used [-Wunused-but-set-variable]
warning: variable 'end_cnt' set but not used [-Wunused-but-set-variable]
warning: variable 'no_of_desc' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Moshe Shemesh says:

====================
Add configuration parameters support

Add configuration parameters setting through devlink.
Each device registers supported configuration parameters table.
Each parameter can be either generic or driver specific.
The user can retrieve data on these parameters by "devlink param show"
command and can set new value to a parameter by "devlink param set"
command.
The parameters can be set in different configuration modes:
  runtime - set while driver is running, no reset required.
  driverinit - applied while driver initializes, requires restart
               driver by devlink reload command.
  permanent - written to device's non-volatile memory, hard reset required.

The patches at the end of the patchset introduce few params that are using
the introduced infrastructure on mlx4 and bnxt.

Command examples and output:

pci/0000:81:00.0:
  name internal_error_reset type generic
    values:
      cmode runtime value true
      cmode driverinit value true
  name max_macs type generic
    values:
      cmode driverinit value 128
  name enable_64b_cqe_eqe type driver-specific
    values:
      cmode driverinit value true
  name enable_4k_uar type driver-specific
    values:
      cmode driverinit value false

pci/0000:81:00.0:
  name internal_error_reset type generic
    values:
      cmode runtime value false
      cmode driverinit value true
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Create initial devlink parameters table for bnxt_en.
Table consists of a permanent generic parameter.

enable_sriov - Enables Single-Root Input/Output Virtualization(SR-IOV)
characteristic of the device.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

enable_sriov - Enables Single-Root Input/Output Virtualization(SR-IOV)
characteristic of the device.
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add mlx4_devlink_reload() to support devlink reload operation.
Add mlx4_devlink_param_load_driverinit_values() to load values which
were set using driverinit configuration mode.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Create initial parameters table for mlx4.
The table consists of two generic parameters and two driver-specific
parameters.
Generic:
  internal_err_reset - Enable reset device on internal errors. This
  parameter can be configured on mlx4 either on runtime or during driver
  initialization.
  max_macs - Max number of MACs per ETH port. For mlx4 this parameter
  value range is between 1 and 128. This parameter can be configured on
  mlx4 only during driver initialization.
Driver specific:
  enable_64b_cqe_eqe - Enable 64 byte CQEs/EQEs when the FW supports it.
  This parameter can be configured on mlx4 only during driver
  initialization.
  enable_4k_uar - Enable using 4K UAR. This parameter can be configured on
  mlx4 only during driver initialization.

Register the parameters table on mlx4_init_one() and unregister on
mlx4_remove_one().
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add 2 first generic parameters to devlink configuration parameters set:
internal_err_reset - When set enables reset device on internal errors.
max_macs - max number of MACs per ETH port.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add devlink_param_notify() function to support devlink param notifications.
Add notification call to devlink param set, register and unregister
functions.
Add devlink_param_value_changed() function to enable the driver notify
devlink on value change. Driver should use this function after value was
changed on any configuration mode part to driverinit.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

"driverinit" configuration mode value is held by devlink to enable
the driver query the value after reload. Two additional functions
added to help the driver get/set the value from/to devlink:
devlink_param_driverinit_value_set() and
devlink_param_driverinit_value_get().
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add param set command to set value for a parameter.
Value can be set to any of the supported configuration modes.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add param get command which gets data per parameter.
Option to dump the parameters data per device.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Define configuration parameters data structure.
Add functions to register and unregister the driver supported
configuration parameters table.
For each parameter registered, the driver should fill all the parameter's
fields. In case the only supported configuration mode is "driverinit"
the parameter's get()/set() functions are not required and should be set
to NULL, for any other configuration mode, these functions are required
and should be set by the driver.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Variable channel is being assigned but is never used hence it is
redundant and can be removed.

Cleans up two clang warnings:
warning: variable 'channel' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Variables my_epid and max_epid are currently assigned and not being
used - however, I suspect they were intended to be used in the for-loops
to reduce the dereferencing of hw.  Replace hw->my_epid and hw->max_epid
with these variables.

Cleans up clang warnings:
warning: variable 'my_epid' set but not used [-Wunused-but-set-variable]
variable 'max_epid' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pointer skb is being assigned but is never used hence it is
redundant and can be removed.

Cleans up clang warning:
warning: variable 'skb' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pointer ndev is being assigned but is never used hence it is
redundant and can be removed.

Cleans up clang warning:
warning: variable 'ndev' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes the following sparse warnings:

drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_utils.c:525:5: warning:
 symbol 'hw_atl_utils_mpi_set_speed' was not declared. Should it be static?
drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_utils.c:536:5: warning:
 symbol 'hw_atl_utils_mpi_set_state' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes the following sparse warnings:

drivers/net/dsa/vitesse-vsc73xx.c:1054:6: warning:
 symbol 'vsc73xx_get_strings' was not declared. Should it be static?
drivers/net/dsa/vitesse-vsc73xx.c:1113:5: warning:
 symbol 'vsc73xx_get_sset_count' was not declared. Should it be static?
drivers/net/dsa/vitesse-vsc73xx.c:1122:6: warning:
 symbol 'vsc73xx_get_ethtool_stats' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Trivial fix to spelling mistake in dev_err error message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After commit 07d78363 ("net: Convert NAPI gro list into a small hash
table.")' there is 8 hash buckets, which allows more flows to be held for
merging.  but MAX_GRO_SKBS, the total held skb for merging, is 8 skb still,
limit the hash table performance.

keep MAX_GRO_SKBS as 8 skb, but limit each hash list length to 8 skb, not
the total 8 skb
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>