- 08 Jun, 2017 13 commits
-
-
Joe Thornber authored
[ Upstream commit 91bcdb92 ] These calls were the wrong way round in __write_initial_superblock. Cc: stable@vger.kernel.org Signed-off-by:
Joe Thornber <ejt@redhat.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
Sasha Levin <alexander.levin@verizon.com>
-
Johan Hovold authored
[ Upstream commit 6aeb75e6 ] Fix a division-by-zero in set_termios when debugging is enabled and a high-enough speed has been requested so that the divisor value becomes zero. Instead of just fixing the offending debug statement, cap the baud rate at the base as a zero divisor value also appears to crash the firmware. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Cc: stable <stable@vger.kernel.org> # 2.6.12 Reviewed-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Johan Hovold authored
[ Upstream commit 26cede34 ] Drop erroneous cpu_to_le32 when setting the baud rate, something which corrupted the divisor on big-endian hosts. Found using sparse: warning: incorrect type in argument 1 (different base types) expected unsigned int [unsigned] [usertype] val got restricted __le32 [usertype] <noident> Fixes: af2ac1a0 ("USB: serial mct_usb232: move DMA buffers to heap") Cc: stable <stable@vger.kernel.org> # 2.6.34 Reviewed-by:
Pete Zaitcev <zaitcev@yahoo.com> Signed-off-by:
-
Anthony Mallet authored
[ Upstream commit bb246681 ] Commit 557aaa7f ("ft232: support the ASYNC_LOW_LATENCY flag") enables unprivileged users to set the FTDI latency timer, but there was a logic flaw that skipped sending the corresponding USB control message to the device. Specifically, the device latency timer would not be updated until next open, something which was later also inadvertently broken by commit c19db4c9 ("USB: ftdi_sio: set device latency timeout at port probe"). A recent commit c6dce262 ("USB: serial: ftdi_sio: fix extreme low-latency setting") disabled the low-latency mode by default so we now need this fix to allow unprivileged users to again enable it. Signed-off-by:
Anthony Mallet <anthony.mallet@laas.fr> [johan: amend commit message] Fixes: 557aaa7f ("ft232: support the ASYNC_LOW_LATENCY flag") Fixes: c19db4c9 ("USB: ftdi_sio: set device latency timeout at port probe"). Cc: stable <stable@vger.kernel.org> # 2.6.31 Signed-off-by:
-
Daniele Palmas authored
[ Upstream commit 40dd4604 ] This patch adds support for Telit ME910 PID 0x1100. Signed-off-by:
Daniele Palmas <dnlplm@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Leonard Crestez authored
[ Upstream commit d8581c7c ] The board file for imx6sx-sdb overrides cpufreq operating points to use higher voltages. This is done because the board has a shared rail for VDD_ARM_IN and VDD_SOC_IN and when using LDO bypass the shared voltage needs to be a value suitable for both ARM and SOC. This only applies to LDO bypass mode, a feature not present in upstream. When LDOs are enabled the effect is to use higher voltages than necessary for no good reason. Setting these higher voltages can make some boards fail to boot with ugly semi-random crashes reminiscent of memory corruption. These failures only happen on board rev. C, rev. B is reported to still work. Signed-off-by:
Leonard Crestez <leonard.crestez@nxp.com> Fixes: 54183bd7 ("ARM: imx6sx-sdb: add revb board and make it default") Cc: stable@vger.kernel.org Signed-off-by:
Shawn Guo <shawnguo@kernel.org> Signed-off-by:
-
Fabio Estevam authored
[ Upstream commit 1dd58e12 ] imx6sx-sdb has custom operating points entries because it has one power supply that drives both VDDARM_IN and VDDSOC_IN. As per the MX6UL datasheet we have the following minimum voltages for 198 MHz operation (after adding the 25mV margin value): VDDARM_IN = 0.975 V VDDSOC_IN = 1.175 V So use 1.175V for the 198MHz operation. Signed-off-by:
Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by:
-
Aleksa Sarai authored
[ Upstream commit cb4a3167 ] Add a new macro for_each_subsys_which that allows all enabled cgroup subsystems to be filtered by a bitmask, such that mask & (1 << ssid) determines if the subsystem is to be processed in the loop body (where ssid is the unique id of the subsystem). Also replace the need_forkexit_callback with two separate bitmasks for each callback to make (ss->{fork,exit}) checks unnecessary. tj: add a short comment for "if (!CGROUP_SUBSYS_COUNT)". Signed-off-by:
Aleksa Sarai <cyphar@cyphar.com> Signed-off-by:
-
Tejun Heo authored
[ Upstream commit 7d7efec3 ] threadgroup_change_begin/end() are used to mark the beginning and end of threadgroup modifying operations to allow code paths which require a threadgroup to stay stable across blocking operations to synchronize against those sections using threadgroup_lock/unlock(). It's currently implemented as a general mechanism in sched.h using per-signal_struct rwsem; however, this never grew non-cgroup use cases and becomes noop if !CONFIG_CGROUPS. It turns out that cgroups is gonna be better served with a different sycnrhonization scheme and is a bit silly to keep cgroups specific details as a general mechanism. What's general here is identifying the places where threadgroups are modified. This patch restructures threadgroup locking so that threadgroup_change_begin/end() become a place where subsystems which need to sycnhronize against threadgroup changes can hook into. cgroup_threadgroup_change_begin/end() which operate on the per-signal_struct rwsem are created and threadgroup_lock/unlock() are moved to cgroup.c and made static. This is pure reorganization which doesn't cause any functional changes. Signed-off-by:
Tejun Heo <tj@kernel.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Signed-off-by:
-
Eric W. Biederman authored
[ Upstream commit b9a985db ] The code can potentially sleep for an indefinite amount of time in zap_pid_ns_processes triggering the hung task timeout, and increasing the system average. This is undesirable. Sleep with a task state of TASK_INTERRUPTIBLE instead of TASK_UNINTERRUPTIBLE to remove these undesirable side effects. Apparently under heavy load this has been allowing Chrome to trigger the hung time task timeout error and cause ChromeOS to reboot. Reported-by:
Vovo Yang <vovoy@google.com> Reported-by:
Guenter Roeck <linux@roeck-us.net> Tested-by:
"Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by:
-
Johan Hovold authored
[ Upstream commit 75cf0679 ] Add missing endianness conversion when using the USB device-descriptor bcdDevice field to construct a firmware file name. Fixes: 8ef80aef ("[IRDA]: irda-usb.c: STIR421x cleanups") Cc: stable <stable@vger.kernel.org> # 2.6.18 Cc: Nick Fedchik <nfedchik@atlantic-link.com.ua> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Martin Schwidefsky authored
[ Upstream commit 07a63cbe ] git commit c5328901 "[S390] entry[64].S improvements" removed the update of the exit_timer lowcore field from the critical section cleanup of the .Lsysc_restore/.Lsysc_done and .Lio_restore/.Lio_done blocks. If the PSW is updated by the critical section cleanup to point to user space again, the interrupt entry code will do a vtime calculation after the cleanup completed with an exit_timer value which has *not* been updated. Due to this incorrect system time deltas are calculated. If an interrupt occured with an old PSW between .Lsysc_restore/.Lsysc_done or .Lio_restore/.Lio_done update __LC_EXIT_TIMER with the system entry time of the interrupt. Cc: stable@vger.kernel.org # 3.3+ Tested-by:
Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Andrey Konovalov authored
[ Upstream commit 5edabca9 ] In the current DCCP implementation an skb for a DCCP_PKT_REQUEST packet is forcibly freed via __kfree_skb in dccp_rcv_state_process if dccp_v6_conn_request successfully returns. However, if IPV6_RECVPKTINFO is set on a socket, the address of the skb is saved to ireq->pktopts and the ref count for skb is incremented in dccp_v6_conn_request, so skb is still in use. Nevertheless, it gets freed in dccp_rcv_state_process. Fix by calling consume_skb instead of doing goto discard and therefore calling __kfree_skb. Similar fixes for TCP: fb7e2399 [TCP]: skb is unexpectedly freed. 0aea76d3 tcp: SYN packets are now simply consumed Signed-off-by:
Andrey Konovalov <andreyknvl@google.com> Acked-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
- 28 May, 2017 7 commits
-
-
Sasha Levin authored
Signed-off-by: -
Eric Dumazet authored
[ Upstream commit 197c949e ] Backport of this upstream commit into stable kernels : 89c22d8c ("net: Fix skb csum races when peeking") exposed a bug in udp stack vs MSG_PEEK support, when user provides a buffer smaller than skb payload. In this case, skb_copy_and_csum_datagram_iovec(skb, sizeof(struct udphdr), msg->msg_iov); returns -EFAULT. This bug does not happen in upstream kernels since Al Viro did a great job to replace this into : skb_copy_and_csum_datagram_msg(skb, sizeof(struct udphdr), msg); This variant is safe vs short buffers. For the time being, instead reverting Herbert Xu patch and add back skb->ip_summed invalid changes, simply store the result of udp_lib_checksum_complete() so that we avoid computing the checksum a second time, and avoid the problematic skb_copy_and_csum_datagram_iovec() call. This patch can be applied on recent kernels as it avoids a double checksumming, then backported to stable kernels as a bug fix. Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
J. Bruce Fields authored
[ Upstream commit f961e3f2 ] In error cases, lgp->lg_layout_type may be out of bounds; so we shouldn't be using it until after the check of nfserr. This was seen to crash nfsd threads when the server receives a LAYOUTGET request with a large layout type. GETDEVICEINFO has the same problem. Reported-by:
Ari Kauppi <Ari.Kauppi@synopsys.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Cc: stable@vger.kernel.org Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
Mark Rutland authored
[ Upstream commit a06040d7 ] Our access_ok() simply hands its arguments over to __range_ok(), which implicitly assummes that the addr parameter is 64 bits wide. This isn't necessarily true for compat code, which might pass down a 32-bit address parameter. In these cases, we don't have a guarantee that the address has been zero extended to 64 bits, and the upper bits of the register may contain unknown values, potentially resulting in a suprious failure. Avoid this by explicitly casting the addr parameter to an unsigned long (as is done on other architectures), ensuring that the parameter is widened appropriately. Fixes: 0aea86a2 ("arm64: User access library functions") Cc: <stable@vger.kernel.org> # 3.7.x- Acked-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
Mark Rutland <mark.rutland@arm.com> Signed-off-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
-
Kristina Martsenko authored
[ Upstream commit f0e421b1 ] Some kernel features don't currently work if a task puts a non-zero address tag in its stack pointer, frame pointer, or frame record entries (FP, LR). For example, with a tagged stack pointer, the kernel can't deliver signals to the process, and the task is killed instead. As another example, with a tagged frame pointer or frame records, perf fails to generate call graphs or resolve symbols. For now, just document these limitations, instead of finding and fixing everything that doesn't work, as it's not known if anyone needs to use tags in these places anyway. In addition, as requested by Dave Martin, generalize the limitations into a general kernel address tag policy, and refactor tagged-pointers.txt to include it. Fixes: d50240a5 ("arm64: mm: permit use of tagged pointers at EL0") Cc: <stable@vger.kernel.org> # 3.12.x- Reviewed-by:
Dave Martin <Dave.Martin@arm.com> Acked-by:
Kristina Martsenko <kristina.martsenko@arm.com> Signed-off-by:
-
Bart Van Assche authored
[ Upstream commit 59ac9c07 ] This patch fixes zero-length READ and WRITE handling in target/FILEIO, which was broken a long time back by: Since: commit d81cb447 Author: Paolo Bonzini <pbonzini@redhat.com> Date: Mon Sep 17 16:36:11 2012 -0700 target: go through normal processing for all zero-length commands which moved zero-length READ and WRITE completion out of target-core, to doing submission into backend driver code. To address this, go ahead and invoke target_complete_cmd() for any non negative return value in fd_do_rw(). Signed-off-by:
Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by:
Hannes Reinecke <hare@suse.com> Reviewed-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Björn Jacke authored
[ Upstream commit 85435d7a ] SFM is mapping doublequote to 0xF020 Without this patch creating files with doublequote fails to Windows/Mac Signed-off-by:
Bjoern Jacke <bjacke@samba.org> Signed-off-by:
Steve French <smfrench@gmail.com> CC: stable <stable@vger.kernel.org> Signed-off-by:
-
- 17 May, 2017 20 commits
-
-
Nicholas Bellinger authored
[ Upstream commit 197b806a ] While testing modification of per se_node_acl queue_depth forcing session reinstatement via lio_target_nacl_cmdsn_depth_store() -> core_tpg_set_initiator_node_queue_depth(), a hung task bug triggered when changing cmdsn_depth invoked session reinstatement while an iscsi login was already waiting for session reinstatement to complete. This can happen when an outstanding se_cmd descriptor is taking a long time to complete, and session reinstatement from iscsi login or cmdsn_depth change occurs concurrently. To address this bug, explicitly set session_fall_back_to_erl0 = 1 when forcing session reinstatement, so session reinstatement is not attempted if an active session is already being shutdown. This patch has been tested with two scenarios. The first when iscsi login is blocked waiting for iscsi session reinstatement to complete followed by queue_depth change via configfs, and second when queue_depth change via configfs us blocked followed by a iscsi login driven session reinstatement. Note this patch depends on commit d36ad77f to handle multiple sessions per se_node_acl when changing cmdsn_depth, and for pre v4.5 kernels will need to be included for stable as well. Reported-by:
Gary Guo <ghg@datera.io> Tested-by:
-
Nicholas Bellinger authored
[ Upstream commit a71a5dc7 ] Following the bugfix for handling non SAM_STAT_GOOD COMPARE_AND_WRITE status during COMMIT phase in commit 9b2792c3, the same bug exists for the READ phase as well. This would manifest first as a lost SCSI response, and eventual hung task during fabric driver logout or re-login, as existing shutdown logic waited for the COMPARE_AND_WRITE se_cmd->cmd_kref to reach zero. To address this bug, compare_and_write_callback() has been changed to set post_ret = 1 and return TCM_LOGICAL_UNIT_COMMUNICATION_FAILURE as necessary to signal failure status. Reported-by:
Bill Borsari <wgb@datera.io> Cc: Bill Borsari <wgb@datera.io> Tested-by:
-
Rob Herring authored
[ Upstream commit eb310036 ] sparse gives the following warning for 'pci_space': ../drivers/of/address.c:266:26: warning: incorrect type in assignment (different base types) ../drivers/of/address.c:266:26: expected unsigned int [unsigned] [usertype] pci_space ../drivers/of/address.c:266:26: got restricted __be32 const [usertype] <noident> It appears that pci_space is only ever accessed on powerpc, so the endian swap is often not needed. Cc: stable@vger.kernel.org Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Luis Henriques authored
[ Upstream commit eeca958d ] The ceph_inode_xattr needs to be released when removing an xattr. Easily reproducible running the 'generic/020' test from xfstests or simply by doing: attr -s attr0 -V 0 /mnt/test && attr -r attr0 /mnt/test While there, also fix the error path. Here's the kmemleak splat: unreferenced object 0xffff88001f86fbc0 (size 64): comm "attr", pid 244, jiffies 4294904246 (age 98.464s) hex dump (first 32 bytes): 40 fa 86 1f 00 88 ff ff 80 32 38 1f 00 88 ff ff @........28..... 00 01 00 00 00 00 ad de 00 02 00 00 00 00 ad de ................ backtrace: [<ffffffff81560199>] kmemleak_alloc+0x49/0xa0 [<ffffffff810f3e5b>] kmem_cache_alloc+0x9b/0xf0 [<ffffffff812b157e>] __ceph_setxattr+0x17e/0x820 [<ffffffff812b1c57>] ceph_set_xattr_handler+0x37/0x40 [<ffffffff8111fb4b>] __vfs_removexattr+0x4b/0x60 [<ffffffff8111fd37>] vfs_removexattr+0x77/0xd0 [<ffffffff8111fdd1>] removexattr+0x41/0x60 [<ffffffff8111fe65>] path_removexattr+0x75/0xa0 [<ffffffff81120aeb>] SyS_lremovexattr+0xb/0x10 [<ffffffff81564b20>] entry_SYSCALL_64_fastpath+0x13/0x94 [<ffffffffffffffff>] 0xffffffffffffffff Cc: stable@vger.kernel.org Signed-off-by:
Luis Henriques <lhenriques@suse.com> Reviewed-by:
"Yan, Zheng" <zyan@redhat.com> Signed-off-by:
Ilya Dryomov <idryomov@gmail.com> Signed-off-by:
-
Steve French authored
[ Upstream commit 7db0a6ef ] Macs send the maximum buffer size in response on ioctl to validate negotiate security information, which causes us to fail the mount as the response buffer is larger than the expected response. Changed ioctl response processing to allow for padding of validate negotiate ioctl response and limit the maximum response size to maximum buffer size. Signed-off-by:
Steve French <steve.french@primarydata.com> CC: Stable <stable@vger.kernel.org> Signed-off-by:
-
Björn Jacke authored
[ Upstream commit b704e70b ] - trailing space maps to 0xF028 - trailing period maps to 0xF029 This fix corrects the mapping of file names which have a trailing character that would otherwise be illegal (period or space) but is allowed by POSIX. Signed-off-by:
-
Andrey Ryabinin authored
[ Upstream commit a5f6a6a9 ] invalidate_bdev() calls cleancache_invalidate_inode() iff ->nrpages != 0 which doen't make any sense. Make sure that invalidate_bdev() always calls cleancache_invalidate_inode() regardless of mapping->nrpages value. Fixes: c515e1fd ("mm/fs: add hooks to support cleancache") Link: http://lkml.kernel.org/r/20170424164135.22350-3-aryabinin@virtuozzo.comSigned-off-by:
Andrey Ryabinin <aryabinin@virtuozzo.com> Reviewed-by:
Jan Kara <jack@suse.cz> Acked-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Ross Zwisler <ross.zwisler@linux.intel.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Alexey Kuznetsov <kuznet@virtuozzo.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Nikolay Borisov <n.borisov.lkml@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Richard Weinberger authored
[ Upstream commit 9abc74a2 ] This is broken since ever but sadly nobody noticed. Recent versions of GDB set DR_CONTROL unconditionally and UML dies due to a heap corruption. It turns out that the PTRACE_POKEUSER was copy&pasted from i386 and assumes that addresses are 4 bytes long. Fix that by using 8 as address size in the calculation. Cc: <stable@vger.kernel.org> Reported-by:
jie cao <cj3054@gmail.com> Signed-off-by:
Richard Weinberger <richard@nod.at> Signed-off-by:
-
James Hogan authored
[ Upstream commit 3a158a62 ] The metag implementation of strncpy_from_user() doesn't validate the src pointer, which could allow reading of arbitrary kernel memory. Add a short access_ok() check to prevent that. Its still possible for it to read across the user/kernel boundary, but it will invariably reach a NUL character after only 9 bytes, leaking only a static kernel address being loaded into D0Re0 at the beginning of __start, which is acceptable for the immediate fix. Reported-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
James Hogan <james.hogan@imgtec.com> Cc: linux-metag@vger.kernel.org Cc: stable@vger.kernel.org Signed-off-by:
-
Steve French authored
[ Upstream commit 26c9cb66 ] Mac requires the unicode flag to be set for cifs, even for the smb echo request (which doesn't have strings). Without this Mac rejects the periodic echo requests (when mounting with cifs) that we use to check if server is down Signed-off-by:
-
James Hogan authored
[ Upstream commit 8a8b5663 ] The __user_bad() macro used by access_ok() has a few corner cases noticed by Al Viro where it doesn't behave correctly: - The kernel range check has off by 1 errors which permit access to the first and last byte of the kernel mapped range. - The kernel range check ends at LINCORE_BASE rather than META_MEMORY_LIMIT, which is ineffective when the kernel is in global space (an extremely uncommon configuration). There are a couple of other shortcomings here too: - Access to the whole of the other address space is permitted (i.e. the global half of the address space when the kernel is in local space). This isn't ideal as it could theoretically still contain privileged mappings set up by the bootloader. - The size argument is unused, permitting user copies which start on valid pages at the end of the user address range and cross the boundary into the kernel address space (e.g. addr = 0x3ffffff0, size > 0x10). It isn't very convenient to add size checks when disallowing certain regions, and it seems far safer to be sure and explicit about what userland is able to access, so invert the logic to allow certain regions instead, and fix the off by 1 errors and missing size checks. This also allows the get_fs() == KERNEL_DS check to be more easily optimised into the user address range case. We now have 3 such allowed regions: - The user address range (incorporating the get_fs() == KERNEL_DS check). - NULL (some kernel code expects this to work, and we'll always catch the fault anyway). - The core code memory region. Fixes: 373cd784 ("metag: Memory handling") Reported-by:
-
Bart Van Assche authored
[ Upstream commit 0e2eb7d1 ] Use the value of the BYTCHK field to determine the size of the Data-Out buffer. For VERIFY, honor the VRPROTECT, DPO and FUA fields. This patch avoids that LIO complains about a mismatch between the expected transfer length and the SCSI CDB length if the value of the BYTCHK field is 0. Signed-off-by:
-
Mikulas Patocka authored
[ Upstream commit 390020ad ] dm-bufio checks a watermark when it allocates a new buffer in __bufio_new(). However, it doesn't check the watermark when the user changes /sys/module/dm_bufio/parameters/max_cache_size_bytes. This may result in a problem - if the watermark is high enough so that all possible buffers are allocated and if the user lowers the value of "max_cache_size_bytes", the watermark will never be checked against the new value because no new buffer would be allocated. To fix this, change __evict_old_buffers() so that it checks the watermark. __evict_old_buffers() is called every 30 seconds, so if the user reduces "max_cache_size_bytes", dm-bufio will react to this change within 30 seconds and decrease memory consumption. Depends-on: 1b0fb5a5 ("dm bufio: avoid a possible ABBA deadlock") Cc: stable@vger.kernel.org Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
-
Mikulas Patocka authored
[ Upstream commit 1b0fb5a5 ] __get_memory_limit() tests if dm_bufio_cache_size changed and calls __cache_size_refresh() if it did. It takes dm_bufio_clients_lock while it already holds the client lock. However, lock ordering is violated because in cleanup_old_buffers() dm_bufio_clients_lock is taken before the client lock. This results in a possible deadlock and lockdep engine warning. Fix this deadlock by changing mutex_lock() to mutex_trylock(). If the lock can't be taken, it will be re-checked next time when a new buffer is allocated. Also add "unlikely" to the if condition, so that the optimizer assumes that the condition is false. Cc: stable@vger.kernel.org Signed-off-by:
-
Szymon Janc authored
[ Upstream commit ab89f0bd ] Running 32bit userspace on 64bit kernel results in MSG_CMSG_COMPAT being defined as 0x80000000. This results in sendmsg failure if used from 32bit userspace running on 64bit kernel. Fix this by accounting for MSG_CMSG_COMPAT in flags check in hci_sock_sendmsg. Signed-off-by:
Szymon Janc <szymon.janc@codecoup.pl> Signed-off-by:
Marko Kiiskila <marko@runtime.io> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org Signed-off-by:
-
Eric Biggers authored
[ Upstream commit 7b4cc978 ] Currently the case of writing via mmap to a file with inline data is not handled. This is maybe a rare case since it requires a writable memory map of a very small file, but it is trivial to trigger with on inline_data filesystem, and it causes the 'BUG_ON(ext4_test_inode_state(inode, EXT4_STATE_MAY_INLINE_DATA));' in ext4_writepages() to be hit: mkfs.ext4 -O inline_data /dev/vdb mount /dev/vdb /mnt xfs_io -f /mnt/file \ -c 'pwrite 0 1' \ -c 'mmap -w 0 1m' \ -c 'mwrite 0 1' \ -c 'fsync' kernel BUG at fs/ext4/inode.c:2723! invalid opcode: 0000 [#1] SMP CPU: 1 PID: 2532 Comm: xfs_io Not tainted 4.11.0-rc1-xfstests-00301-g071d9acf3d1f #633 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-20170228_101828-anatol 04/01/2014 task: ffff88003d3a8040 task.stack: ffffc90000300000 RIP: 0010:ext4_writepages+0xc89/0xf8a RSP: 0018:ffffc90000303ca0 EFLAGS: 00010283 RAX: 0000028410000000 RBX: ffff8800383fa3b0 RCX: ffffffff812afcdc RDX: 00000a9d00000246 RSI: ffffffff81e660e0 RDI: 0000000000000246 RBP: ffffc90000303dc0 R08: 0000000000000002 R09: 869618e8f99b4fa5 R10: 00000000852287a2 R11: 00000000a03b49f4 R12: ffff88003808e698 R13: 0000000000000000 R14: 7fffffffffffffff R15: 7fffffffffffffff FS: 00007fd3e53094c0(0000) GS:ffff88003e400000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fd3e4c51000 CR3: 000000003d554000 CR4: 00000000003406e0 Call Trace: ? _raw_spin_unlock+0x27/0x2a ? kvm_clock_read+0x1e/0x20 do_writepages+0x23/0x2c ? do_writepages+0x23/0x2c __filemap_fdatawrite_range+0x80/0x87 filemap_write_and_wait_range+0x67/0x8c ext4_sync_file+0x20e/0x472 vfs_fsync_range+0x8e/0x9f ? syscall_trace_enter+0x25b/0x2d0 vfs_fsync+0x1c/0x1e do_fsync+0x31/0x4a SyS_fsync+0x10/0x14 do_syscall_64+0x69/0x131 entry_SYSCALL64_slow_path+0x25/0x25 We could try to be smart and keep the inline data in this case, or at least support delayed allocation when allocating the block, but these solutions would be more complicated and don't seem worthwhile given how rare this case seems to be. So just fix the bug by calling ext4_convert_inline_data() when we're asked to make a page writable, so that any inline data gets evicted, with the block allocated immediately. Reported-by:
Nick Alcock <nick.alcock@oracle.com> Cc: stable@vger.kernel.org Reviewed-by:
Andreas Dilger <adilger@dilger.ca> Signed-off-by:
Eric Biggers <ebiggers@google.com> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Takashi Iwai authored
[ Upstream commit d66bb160 ] proc_create_mount_point() forgot to increase the parent's nlink, and it resulted in unbalanced hard link numbers, e.g. /proc/fs shows one less than expected. Fixes: eb6d38d5 ("proc: Allow creating permanently empty directories...") Cc: stable@vger.kernel.org Reported-by:
Tristan Ye <tristan.ye@suse.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Adrian Salido authored
[ Upstream commit 4617f564 ] When calling a dm ioctl that doesn't process any data (IOCTL_FLAGS_NO_PARAMS), the contents of the data field in struct dm_ioctl are left initialized. Current code is incorrectly extending the size of data copied back to user, causing the contents of kernel stack to be leaked to user. Fix by only copying contents before data and allow the functions processing the ioctl to override. Cc: stable@vger.kernel.org Signed-off-by:
Adrian Salido <salidoa@google.com> Reviewed-by:
Alasdair G Kergon <agk@redhat.com> Signed-off-by:
-
J. Bruce Fields authored
[ Upstream commit 13bf9fbf ] The NFSv2/v3 code does not systematically check whether we decode past the end of the buffer. This generally appears to be harmless, but there are a few places where we do arithmetic on the pointers involved and don't account for the possibility that a length could be negative. Add checks to catch these. Reported-by:
Tuomas Haanpää <thaan@synopsys.com> Reported-by:
Ari Kauppi <ari@synopsys.com> Reviewed-by:
NeilBrown <neilb@suse.com> Cc: stable@vger.kernel.org Signed-off-by:
-
J. Bruce Fields authored
[ Upstream commit db44bac4 ] Use a couple shortcuts that will simplify a following bugfix. Cc: stable@vger.kernel.org Signed-off-by:
-
