- 04 Sep, 2014 19 commits
-
-
Jacob Keller authored
Hardware has a limited number of pools available (64). Previously, no checks were in place to limit the number of accelerated macvlan devices based on the number of pools. Normally this would be ok, because there was already a limit for these well below the number of available pools. However, SR-IOV uses the very same pools. Therefor, we need to ensure that the total number of pools (number of VFs plus the number of non-VF pools in use for accelerated macvlans) does not exceed the number of pools available in hardware. This patch resolves a kernel NULL pointer dereference caused by the following commands: $modprobe ixgbe max_vfs=63 $ethtool -K eth2 l2-fwd-offload on $ip link add link eth2 macvlan0 type macvlan $ip link set dev macvlan0 up [ 992.950080] BUG: unable to handle kernel NULL pointer dereference at 0000000000000056 [ 992.951109] IP: [<ffffffffa003b71e>] ixgbe_disable_fwd_ring+0x1e/0xf0 [ixgbe] [ 992.951684] PGD 22a80e067 PUD 232e9b067 PMD 0 [ 992.952389] Oops: 0000 [#1] SMP [ 992.953014] Modules linked in: nfsd lockd nfs_acl exportfs auth_rpcgss oid_registry sunrpc bridge stp llc vhost_net macvtap macvlan vhost tun kvm_intel kvm ioatdma ixgbe mdio igb dca [ 992.956042] CPU: 2 PID: 11928 Comm: ifconfig Not tainted 3.16.0-rc6-net-next-07-29-2014-FCoE+ #1 [ 992.956915] Hardware name: Intel Corporation S2600CO/S2600CO, BIOS SE5C600.86B.02.03.0003.041920141333 04/19/2014 [ 992.957791] task: ffff8804341c0000 ti: ffff8801d7dc8000 task.ti: ffff8801d7dc8000 [ 992.958660] RIP: 0010:[<ffffffffa003b71e>] [<ffffffffa003b71e>] ixgbe_disable_fwd_ring+0x1e/0xf0 [ixgbe] [ 992.959613] RSP: 0018:ffff8801d7dcbbb8 EFLAGS: 00010286 [ 992.960093] RAX: 0000000000000001 RBX: 0000000000000000 RCX: 0000000000000001 [ 992.960575] RDX: ffff880232eb7000 RSI: 0000000000000000 RDI: ffff88022dc05800 [ 992.961059] RBP: ffff8801d7dcbbd8 R08: 0000000000000000 R09: 0000000000000000 [ 992.961541] R10: 0000000000000001 R11: 0000000000000000 R12: ffff88022ec20980 [ 992.962023] R13: ffff880232eb7000 R14: 0000000000000001 R15: 0000000000000001 [ 992.962508] FS: 00007fab264887a0(0000) GS:ffff880237640000(0000) knlGS:0000000000000000 [ 992.963378] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 992.963858] CR2: 0000000000000056 CR3: 000000022a939000 CR4: 00000000001427e0 [ 992.964340] Stack: [ 992.964806] ffff88022ec28840 ffff88022ec20980 ffff88022dc05800 ffff880232eb7000 [ 992.965976] ffff8801d7dcbc28 ffffffffa003bae8 ffff8801d7dcbbe8 0000000000000400 [ 992.967147] 000000000000000d ffff88022ec20980 ffff88022ec20000 ffff88022dc05800 [ 992.968319] Call Trace: [ 992.968795] [<ffffffffa003bae8>] ixgbe_fwd_ring_up+0x88/0x280 [ixgbe] [ 992.969284] [<ffffffffa0041d83>] ixgbe_fwd_add+0x173/0x220 [ixgbe] [ 992.969767] [<ffffffffa015056c>] macvlan_open+0x1bc/0x230 [macvlan] [ 992.970256] [<ffffffff816b8de7>] __dev_open+0xd7/0x150 [ 992.970735] [<ffffffff816b8bd7>] __dev_change_flags+0xa7/0x170 [ 992.971220] [<ffffffff816b8ccb>] dev_change_flags+0x2b/0x70 [ 992.971703] [<ffffffff817471b2>] devinet_ioctl+0x602/0x6d0 [ 992.972184] [<ffffffff81748168>] inet_ioctl+0x78/0x90 [ 992.972666] [<ffffffff816a143b>] sock_do_ioctl+0x2b/0x70 [ 992.973146] [<ffffffff816a14ed>] sock_ioctl+0x6d/0x260 [ 992.973627] [<ffffffff811ad3b4>] do_vfs_ioctl+0x84/0x540 [ 992.974109] [<ffffffff811a4c81>] ? final_putname+0x21/0x50 [ 992.974593] [<ffffffff818725d5>] ? sysret_check+0x22/0x5d [ 992.975073] [<ffffffff811ad901>] SyS_ioctl+0x91/0xa0 [ 992.975550] [<ffffffff818725a9>] system_call_fastpath+0x16/0x1b [ 992.976026] Code: ff 66 66 66 2e 0f 1f 84 00 00 00 00 00 55 48 89 e5 48 83 ec 20 48 89 5d e8 4c 89 65 f0 48 89 f3 4c 89 6d f8 4c 8b a7 08 02 00 00 <44> 0f b6 6e 56 44 03 af 14 02 00 00 4c 89 e7 e8 5e f2 ff ff be [ 992.982261] RIP [<ffffffffa003b71e>] ixgbe_disable_fwd_ring+0x1e/0xf0 [ixgbe] [ 992.983212] RSP <ffff8801d7dcbbb8> [ 992.983681] CR2: 0000000000000056 [ 992.984248] ---[ end trace 9f54802b5cc3638b ]--- Cc: John Fastabend <john.r.fastabend@intel.com> Signed-off-by:
Jacob Keller <jacob.e.keller@intel.com> Tested-by:
Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Jacob Keller authored
Since we previously called ixgbe_set_num_queues just prior to attempting to set our interrupt scheme, it may be non obvious why we have to call it again inside the function. Add a comment which helps make it more obvious that we are resetting features based on the fact that we do not have MSI-X enabled, and cannot use the previous settings. Signed-off-by:
-
Emil Tantilov authored
VFLINKS.LINKUP bit tends to flap when a DA or SFP+ cable is disconnected. It can take up to 500 usecs for the LINKUP bit to be correct. This patch resolves the issue by introducing a delay for 82599 VFs of at least 500 usecs to make sure the VFLINKS value is correct. Signed-off-by:
Emil Tantilov <emil.s.tantilov@intel.com> Tested-by:
-
Emil Tantilov authored
ixgbe initiates a reset of the interface on link loss with pending Tx work in order to clear the rings. This patch extends the pending Tx work check to the VF interfaces with the same purpose. Signed-off-by:
-
Alexander Duyck authored
This change makes it so that the behavior for FDB handling is consistent between both the SR-IOV and non-SR-IOV cases. The main change here is that we perform bounds checking on the number of SR-IOV addresses regardless of if SR-IOV is enabled or not as we can only support a certain number of addresses in the hardware. Signed-off-by:
Alexander Duyck <alexander.h.duyck@intel.com> Tested-by:
-
Ethan Zhao authored
There is global funcion pci_vfs_assigned(), so use it instead of composing local one. Signed-off-by:
Ethan Zhao <ethan.kernel@gmail.com> Tested-by:
Sibai Li <sibai.li@intel.com> Signed-off-by:
-
Catherine Sullivan authored
Bump i40e version to 1.0.11 and i40evf version to 1.0.5. Change-ID: I63a60fa2efe82aae87a8a3095f43218db57d46ce Signed-off-by:
Catherine Sullivan <catherine.sullivan@intel.com> Tested-by:
Jim Young <jamesx.m.young@intel.com>
-
Jesse Brandeburg authored
This fixes the panic under traffic load when resetting. This issue could also show up if/whenever there is a Tx-timeout. Change-ID: Ie393a1f17fd5d962e56fc3bfe784899ef25402f5 Signed-off-by:
Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by:
Mitch Williams <mitch.a.williams@intel.com> Tested-by:
-
Anjali Singhai Jain authored
We shouldn't restart Admin queue subtask if PF reset fails since we do not have the AQ setup at that point. This patch makes sure we disable AQ clean subtask when PF reset fails. This will resolve an occasional kernel panic when PF reset fails for some reason. Change-ID: I11a747773362a8c5c0ad7a10cd34be0bda8eb9e8 Signed-off-by:
Anjali Singhai Jain <anjali.singhai@intel.com> Tested-by:
-
Jesse Brandeburg authored
The driver is un-necessarily printing a warning that is only marginally useful to the user. Make the warning only print if extended driver string printing is enabled, other messages related to a reset event will still continue to print. Change-ID: I5e8beca6516a2f176cd2e72b0ac2b3b909e6c953 Signed-off-by:
-
Catherine Sullivan authored
Since we don't seem to be getting an LSE telling us link is going down during set_phy_config (but we do get an LSE telling us we are coming back up), fake one for the OS and tell them link is going down. Also do an atomic restart no matter what because there are times the user may want to end with link up even if they started with link down (like if they accidentally set it to a speed that can't link and are trying to fix it). Change-ID: I0a642af9c1d0feb67bce741aba1a9c33bd349ed6 Signed-off-by:
-
Serey Kong authored
Remove unnecessary setting of "ret" variable as it's already set at the top of the function. Change-ID: Icaccfc67f335817a23579b7c43625d59ad6c9925 Signed-off-by:
Serey Kong <serey.kong@intel.com> Tested-by:
-
Serey Kong authored
Change "spoofck" to "spoofchk" to be consistent with as defined in netdev. Change-ID: I9866d6284cb5f92c8d71dc0776c6d1e71dfb62a5 Signed-off-by:
-
Catherine Sullivan authored
Allow the user to change auto-negotiation and speed settings if link is down. Change-ID: I372967c627682b5e1835f623a7cbf41b21b51043 Signed-off-by:
-
Catherine Sullivan authored
Now that fw has implemented dual speed module support, we can add ours. Also, add the phy type for 1G LR/SR and set its media type to fiber. Lastly, instead of a WARN_ON if the phy type is not recognized just print a warning. Change-ID: I2e5227d4a8c2907b0ed423038e5dbce774e466b0 Signed-off-by:
-
Rick Jones authored
It would appear the mlx4_en driver was still making a call to dev_kfree_skb_any() where dev_consume_skb_any() would be more appropriate. This should make dropped packet profiling/tracking easier/better over a NIC driven by mlx4_en. Signed-off-by:
Rick Jones <rick.jones2@hp.com> Acked-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ying Xue authored
Although rhashtable library allows user to specify a quiet big size for user's created hash table, the table may be shrunk to a very small size - HASH_MIN_SIZE(4) after object is removed from the table at the first time. Subsequently, even if the total amount of objects saved in the table is quite lower than user's initial setting in a long time, the hash table size is still dynamically adjusted by rhashtable_shrink() or rhashtable_expand() each time object is inserted or removed from the table. However, as synchronize_rcu() has to be called when table is shrunk or expanded by the two functions, we should permit user to set the minimum table size through configuring the minimum number of shifts according to user specific requirement, avoiding these expensive actions of shrinking or expanding because of calling synchronize_rcu(). Signed-off-by:
Ying Xue <ying.xue@windriver.com> Acked-by:
Thomas Graf <tgraf@suug.ch> Signed-off-by:
-
Jesper Dangaard Brouer authored
In commit 50cbe9ab ("net: Validate xmit SKBs right when we pull them out of the qdisc") the validation code was moved out of dev_hard_start_xmit and into dequeue_skb. However this overlooked the fact that we do not always enqueue the skb onto a qdisc. First situation is if qdisc have flag TCQ_F_CAN_BYPASS and qdisc is empty. Second situation is if there is no qdisc on the device, which is a common case for software devices. Originally spotted and inital patch by Alexander Duyck. As a result Alex was seeing issues trying to connect to a vhost_net interface after commit 50cbe9ab was applied. Added a call to validate_xmit_skb() in __dev_xmit_skb(), in the code path for qdiscs with TCQ_F_CAN_BYPASS flag, and in __dev_queue_xmit() when no qdisc. Also handle the error situation where dev_hard_start_xmit() could return a skb list, and does not return dev_xmit_complete(rc) and falls through to the kfree_skb(), in that situation it should call kfree_skb_list(). Fixes: 50cbe9ab ("net: Validate xmit SKBs right when we pull them out of the qdisc") Signed-off-by:
Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by:
-
Jesper Dangaard Brouer authored
More minor fixes to merge commit 53fda7f7 (Merge branch 'xmit_list') that allows us to work with a list of SKBs. Fixing exit cases in qdisc_reset() and qdisc_destroy(), where a leftover requeued SKB (qdisc->gso_skb) can have the potential of being a skb list, thus use kfree_skb_list(). This is a followup to commit 10770bc2 ("qdisc: adjustments for API allowing skb list xmits"). Signed-off-by:
-
- 02 Sep, 2014 21 commits
-
-
Jesper Dangaard Brouer authored
Minor adjustments for merge commit 53fda7f7 (Merge branch 'xmit_list') that allows us to work with a list of SKBs. Update code doc to function sch_direct_xmit(). In handle_dev_cpu_collision() use kfree_skb_list() in error handling. Signed-off-by:
-
Jingoo Han authored
Remove unused 'dev' variable from arc_emac_remove(), since it's not being used any more. Signed-off-by:
Jingoo Han <jg1.han@samsung.com> Signed-off-by:
-
David Wood authored
Remove unnecessary double parenthesis around if statement. Signed-off-by:
David Wood <devel@dtwood.uk> Signed-off-by:
-
David S. Miller authored
Nicolas Dichtel says: ==================== rtnl: send notification in do_setlink() This series ensures to call the notifier chain and to send a netlink message when a change is done by do_setlink(). The three first patches mainly prepare the last one, which do this change. ==================== Signed-off-by: -
Nicolas Dichtel authored
Depending on which parameters were updated, the changes were not propagated via the notifier chain and netlink. The new flag has been set only when the change did not cause a call to the notifier chain and/or to the netlink notification functions. Signed-off-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by:
-
Nicolas Dichtel authored
There is no functional changes with this commit, it only prepares the next one. Signed-off-by:
-
Nicolas Dichtel authored
The only effect of this patch is to print a warning if IFLA_LINKMODE is updated and a following change fails. Signed-off-by:
-
Nicolas Dichtel authored
The only effect of this patch is to print a warning if IFLA_TXQLEN is updated and a following change fails. Signed-off-by:
-
David S. Miller authored
Sathya Perla says: ==================== be2net: patch set v2 changes: add a new line after variable declaration in patch 12. *** Patch 1 adds a few new log messages to help debugging in failure cases. Patch 2 uses new macros for parsing RX/TX completions and TX wrbs to help shorten the lines. Patch 3 adds a description for the RX counter rx_input_fifo_overflow_drop. Patch 4 adds TX completion error statistics reporting via ethtool. Patch 5 adds a dma_mapping_error counter and its reporting via ethtool. Patch 6 fixes up log messages in the Lancer FW download path. Patch 7 replaces gotos with direct return statements. Patch 8 cleans up be_change_mtu() code by using a new macro BE_MAX_MTU Patch 9 makes be_cmd_get_regs() routine to return an integer status similar to other FW cmd routines in be_cmds.c Patch 10 gets rid of TX budget as enforcing a budget on TX completion processing in NAPI is neither suggested nor it provides a performance benefit. Patch 11 defines and uses a new macro for_all_tx_queues_on_eq() similar to the RX processing code. Patch 12 queries max_tx_qs from the FW for BE3 super-nic profiles. For those profiles, the driver cannot assume a constant BE3_MAX_TX_QS value, as the value may change for each function. Please consider applying this patch set to the net-next tree. Thanks! ==================== Signed-off-by: -
Suresh Reddy authored
In the BE3 super-nic profile, the max_tx_qs value can vary for each function. So the driver needs to query this value from FW instead of using the pre-defined constant BE3_MAX_TX_QS. Signed-off-by:
Suresh Reddy <Suresh.Reddy@emulex.com> Signed-off-by:
Sathya Perla <sathya.perla@emulex.com> Signed-off-by:
-
Sathya Perla authored
Replace the for() loop that traverses all the TX queues on an EQ with the macro for_all_tx_queues_on_eq(). With this expalnatory name, the one line comment is not required anymore. Signed-off-by:
-
Sathya Perla authored
Enforcing a budget on the TX completion processing in NAPI doesn't benefit performance in anyway. Just get rid of it. Signed-off-by:
-
Vasundhara Volam authored
There are a few failure cases in be_cmd_get_regs() that ideally must return an error value. This style is used across all the routines in be_cmds.c with this routine being an exception. This patch fixes this. Signed-off-by:
Vasundhara Volam <vasundhara.volam@emulex.com> Signed-off-by:
-
Kalesh AP authored
This patch defines a new macro BE_MAX_MTU to make the code in be_change_mtu() more readable. Signed-off-by:
Kalesh AP <kalesh.purayil@emulex.com> Signed-off-by:
-
Kalesh AP authored
In cases where there is no extra code to handle an error, this patch replaces gotos with a direct return statement. Signed-off-by:
-
Kalesh AP authored
Log messages in the Lancer FW download path have issues such as: - a single message spanning multiple lines - the success message is logged even in failure cases - status codes are already logged in the FW cmd routines This patch fixes these issues. Signed-off-by:
-
Vasundhara Volam authored
Add a dma_mapping_error counter to count the number of packets dropped due to DMA mapping errors. Signed-off-by:
-
Kalesh AP authored
HW reports TX completion errors in TX completion. This patch adds these counters to ethtool statistics. Signed-off-by:
-
Sathya Perla authored
Signed-off-by:
-
Sathya Perla authored
The AMAP_GET/SET_BITS() macro calls take structure name as a parameter and hence are long and span more than one line. Replace these calls with a wrapper macros for RX/Tx compls and TX wrb. This results in fewer lines and more readable code in be_main.c Signed-off-by:
-
Sathya Perla authored
This patch adds the following log messages to help debugging failure cases: 1) log FW version number: this is useful when driver initialization fails and the FW version number cannot be queried via ethtool 2) per function resource limits for BEx chips: these values are currently being printed only for Skyhawk and Lancer 3) PCI BAR mapping failure 4) function_mode/caps queried from FW: this helps catch any FW bugs that could advertise wrong capabilities to the driver Signed-off-by:
-
