Conflicts:
	drivers/hid/hid-ids.h

Conflicts:
	drivers/hid/hid-ids.h

Conflicts:
	drivers/hid/hid-ids.h

Conflicts:
	drivers/hid/hid-ids.h

This reverts commit ed9eac5b. As
reported by Bastien Nocera, the device actually uses a completely
different protocol, so simply adding VID/PID doesn't work and
completely new driver will need to be written.
Reported-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Remove 'default !EMBEDDED' from ACRUX force feedback driver
entry.

See commit message of 73d5e8f7 ("HID: fix up 'EMBEDDED' mess
in Kconfig") for explanation and reasoning.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Adds force feedback support for ACRUX USB game controllers.
These devices are mass produced in China by several vendors.
Signed-off-by: Sergei Kolzun <x0r@dv-life.ru>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

These devices report a usage page of type "consumer" and a usage of
"Programmable buttons". They are hence ignored by the hid-input layer.

Force the registration of an input device by using the new quirk type
HID_QUIRK_HIDINPUT_FORCE.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

For devices with exotic HID report descriptors, it might be necessary to
make the HID core force the registration of an input device. Make that
possible by introducing a new quirk type.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

SMART Technologies has recommended this change to fix a problem reported
with SMART Board series interactive whiteboards.

A description of the device-specific symptom follows:

  When the board is connected my mouse bounces up to the top left corner.

Bjorn has tested this fix with model SB680.
Tested-by: Bjorn Behrendt <bbehrendt@msjvermont.org>
Signed-off-by: Forest Bond <forest@alittletooquiet.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

There is only one extra button for Conceptronic that wasn't yet present.
The button has code 0xffbc0027 and the description is "Toggle between
display ratios". So I picked KEY_MODE for this button.
Signed-off-by: Kees Bakker <kees.bakker@xs4all.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

* 'arm/defconfig/reduced-v2.6.35-rc1' of git://git.pengutronix.de/git/ukl/linux-2.6:
  ARM: reduce defconfigs

This is a big change, but results in no loss of information, despite us
losing almost 200k lines:

 177 files changed, 652 insertions(+), 194157 deletions(-)

and Grant Likely thinks powerpc can also use the same reduction
technique.

The python script that did the reduction looks like this:

    #! /usr/bin/env python
    # vim: set fileencoding=utf-8 :
    # Copyright (C) 2010 by Uwe Kleine-König <u.kleine-koenig@pengutronix.de>

    import re
    import subprocess
    import os
    import sys

    # This prevents including a timestamp in the .config which makes comparing a
    # bit easier.
    os.environ['KCONFIG_NOTIMESTAMP'] = 'Yes, please'

    # XXX: get these using getopt
    kernel_tree = '' # os.path.join(os.environ['HOME'], 'gsrc', 'linux-2.6')
    arch = 'arm'
    target = sys.argv[1]
    defconfig_src = os.path.join(kernel_tree, 'arch/%s/configs/%s' % (arch, target))

    subprocess.check_call(['make', '-s', 'ARCH=%s' % arch, target])
    origconfig = list(open('.config'))
    config = list(origconfig)
    config_size = os.stat('.config').st_size

    i = 0

    while i < len(config):
        print 'test for %r' % config[i]
        defconfig = open(defconfig_src, 'w')
        defconfig.writelines(config[:i])
        defconfig.writelines(config[i + 1:])
        defconfig.close()
        subprocess.check_call(['make', '-s', 'ARCH=%s' % arch, target])
        if os.stat('.config').st_size == config_size and list(open('.config')) == origconfig:
            del config[i]
        else:
            i += 1

    defconfig = open(defconfig_src, 'w')
    defconfig.writelines(config)
    defconfig.close()

which is pretty self-explanatory.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Acked-by: Russell King <linux@arm.linux.org.uk>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'fix/hda' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: hda - Restore cleared pin controls on resume

* 'v4l_for_2.6.35' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
  V4L/DVB: uvc: Fix multiple symbols definitions with UVC gadget and host drivers
  V4L/DVB: v4l: mem2mem_testdev: fix g_fmt NULL pointer dereference
  V4L/DVB: uvcvideo: Power line frequency control doesn't support GET_MIN/MAX/RES
  V4L/DVB: ivtv: Add delay to ensure the decoder always restarts with a blank screen
  V4L/DVB: Documentation: Add the Philips FQ1236 MK5 to video4linux/CARDLIST.tuner
  V4L/DVB: tveeprom: Add an entry for tuner code 168: a TCL M30WTP-4N-E tuner
  V4L/DVB: tuner: Add a definition for the Philips FQ1236 MK5 NTSC tuner
  V4L/DVB: OMAP_VOUT: fix: Module params were not working through bootargs
  V4L/DVB: OMAP_VOUT: fix: Replaced dma-sg with dma-contig
  V4L/DVB: OMAP_VOUT:Build FIX: Rebased against latest DSS2 changes

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: Send Report ID when numbered reports are sent over the control endpoint.
  HID: Enable HID_QUIRK_MULTI_INPUT for Retro Adaptor
  HID: add support for CH Eclipse yoke
  HID: eliminate a double lock in debug code
  HID: ntrig: add support for new firwmare versions
  HID: check for HID_QUIRK_IGNORE during probing
  HID: roccat: fix modules interdependencies

File patterns are one per line.
Fixed include file location.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Hmmm. There are still people who have their editor setup with tabwidth 4.
Some of the entries were added with tabwidth 4, and for these people
the lineup looks OK. But in the Linux kernel source we use tabwidth 8.

This patch repairs that whitespace so that the number align properly.
Signed-off-by: Kees Bakker <kees.bakker@xs4all.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

As our device may be hot-unplugged and framebuffer cannot handle
this case by itself we need to keep track of usage count so as
to release fb_info and framebuffer memory only after the last user
has closed framebuffer.

We need to do the freeing in a scheduled work as fb_release()
is called with fb_info lock held.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Reallocating memory in depth change does not work well if some
userspace application has mmapped() the framebuffer as that mapping
does not get adjusted (thus application continues to write to old
buffer).
In addition doing deferred_io_cleanup() and init() inside of set_par()
tends to deadlock with fbcon's flashing cursor.

Avoid all this by allocating a buffer that can hold 8bpp framebuffer
and just use 1/8 of it while running at 1bpp.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Add a minimal palette so fbcon does not try to dereference
a NULL point when fb is set to 8bpp.

fbcon stores pixels the other way around in bytes for 1bpp
than intially implemented, correct this.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

The Report ID wasn't sent as part of the payload for reports which were sent
over the control endpoint. This is required by section 8.1 of the HID spec.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

The X and Y values have two more significant bits in the same byte
that contains click status.  Include these in the reported value.
Thanks to Iain Hibbert of NetBSD for pointing this out.
Signed-off-by: Michael Poole <mdpoole@troilus.org>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

The evdev multitouch protocol requires that a last MT sync event must be
sent after all touches are up. This change adds the last MT sync event
to the hid-magicmouse driver.

Also, don't send events when a touch leaves.
Signed-off-by: Chase Douglas <chase.douglas@canonical.com>
Acked-by: Michael Poole <mdpoole@troilus.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Adjust ordering if framebuffer (un)registration and defio init/cleanup
to match the correct order (init defio, register FB ... unregister FB,
cleanup defio)
Acked-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

The UVC gadget driver borrowed code from the UVC host driver without
changing the symbol names. This results in a namespace clash with
multiple definitions of several symbols when compiling both drivers in
the kernel.

Make all generic UVC functions and variables static in the UVC gadget
driver, as the symbols are not referenced outside of the gadget driver.
Rename the uvc_trace_param global variable to uvc_gadget_trace_param.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  hwmon: Fix autoloading of fschmd on recent Fujitsu machines
  hwmon: (coretemp) Properly label the sensors
  hwmon: (coretemp) Skip duplicate CPU entries
  hwmon: (it87) Fix in7 on IT8720F
  hwmon: (k8temp) Fix temperature reporting for ASB1 processor revisions

* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  i2c/mips: Fix error return codes from Sibyte i2c bus driver
  i2c: Fix probability check

The VENDOR_IDs were mostly in alphabetical order, but some of the
newer entries were not added as such. Some entries were added just
at the end, some were added in the middle.

This patch places the entries once again in a properly sorted
order.
Signed-off-by: Kees Bakker <kees.bakker@xs4all.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Patch for linux-2.6.35-rc4 mainline kernel to enable Paul Qureshi's
Retro Adapter [http://keio.dk/retroadapter.html], an open source USB
device which allows controllers and joysticks from classic computers
and consoles to work on modern PCs, to appear as two separate devices
under Linux.
Signed-off-by: Peter Edwards <samwise@bagshot-row.org>
Acked-by: Paul Qureshi <retro@world3.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

This USB flight yoke needs the NOGET quirk, like most of CH's other
products. This patch adds that.
Signed-off-by: Jonathan Rockway <jon@jrock.us>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Sibyte i2c bus driver returns non-descriptive error values.
Update to return error values as defined in Documentation/i2c/fault-codes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

The new unified probing function differs from the original code, and
the preliminary test whether probing is possible must be updated
accordingly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Fujitsu slightly changed the DMI strings in their recent machines,
(for example the D2778) and this breaks the automatic loading of the
needed fschmd driver. Being more tolerant on string comparison fixes
the issue.

This closes bug #15634:
https://bugzilla.kernel.org/show_bug.cgi?id=15634Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Sergey Spiridonov <sena@hurd.homeunix.org>
Cc: Hans de Goede <hdegoede@redhat.com>

Don't assume that CPU entry number and core ID always match. It
worked in the simple cases (single CPU, no HT) but fails on
multi-CPU systems.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Huaxu Wan <huaxu.wan@intel.com>
Cc: stable@kernel.org

On hyper-threaded CPUs, each core appears twice in the CPU list. Skip
the second entry to avoid duplicate sensors.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Huaxu Wan <huaxu.wan@intel.com>
Cc: stable@kernel.org

The IT8720F has no VIN7 pin, so VCCH should always be routed
internally to VIN7 with an internal divider. Curiously, there still
is a configuration bit to control this, which means it can be set
incorrectly. And even more curiously, many boards out there are
improperly configured, even though the IT8720F datasheet claims that
the internal routing of VCCH to VIN7 is the default setting. So we
force the internal routing in this case.

It turns out that all boards with the wrong setting are from Gigabyte,
so I suspect a BIOS bug. But it's easy enough to workaround in the
driver, so let's do it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jean-Marc Spaggiari <jean-marc@spaggiari.org>
Cc: stable@kernel.org

Reported temperature for ASB1 CPUs is too high.
Add ASB1 CPU revisions (these are also non-desktop variants) to the
list of CPUs for which the temperature fixup is not required.

Example: (from LENOVO ThinkPad Edge 13, 01972NG, system was idle)

  Current kernel reports

  $ sensors
  k8temp-pci-00c3
  Adapter: PCI adapter
  Core0 Temp:  +74.0 C
  Core0 Temp:  +70.0 C
  Core1 Temp:  +69.0 C
  Core1 Temp:  +70.0 C

  With this patch I have

  $ sensors
  k8temp-pci-00c3
  Adapter: PCI adapter
  Core0 Temp:  +54.0 C
  Core0 Temp:  +51.0 C
  Core1 Temp:  +48.0 C
  Core1 Temp:  +49.0 C

Cc: stable@kernel.org [.32.x .33.x, .34.x]
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Many codecs now clear the pin controls at suspend via snd_hda_shutup_pins()
for reducing the click noise at power-off.  But this leaves some pins
uninitialized, and they'll be never recovered after resume.

This patch adds the proper recovery of cleared pin controls on resume.
Also it adds a check of bus->shutdown so that pins won't be cleared at
module unloading.

Reference: Kernel bug 16339
	http://bugzilla.kernel.org/show_bug.cgi?id=16339

Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>