These are the ioctls for the special-purpose misc device /dev/nosy, the
interface to the IEEE 1394 packet sniffer/ protocol analyzer driver.
Currently only the numbers 00...02 are in use; let's block a few more
for unforeseen use cases.

Cc: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Replace home-grown printk wrapper macros by ones from kernel.h and
device.h.

Also raise the log level in set_phy_reg() from debug to error because
these are really error conditions.  Could even be WARN_ON.  Lower the
log level in the device probe and driver shutdown from notice to info.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

1.)  The DMA programs (struct pcl) are PCI-endian = little endian data
(except for the 3rd quadlet in a PCL which the controller does not
touch).  Annotate them as such.

Fix all accesses of the PCL to work with big endian CPUs also.  Not
actually tested, I only have a little endian PC to test with.  This
includes replacement of a bitfield struct pcl_status by open-coded
shift and mask operations.

2.)  The two __attribute__ ((packed)) at struct pcl are not really
required since it consists of u32/__le32 only, i.e. there will be no
padding with or without the attribute.

3.)  The received IEEE 1394 data are byteswapped by the controller from
IEEE 1394 endian = big endian to PCI endian = little endian because the
PCL_BIGENDIAN control bit is set.  Therefore annotate the DMA buffer as
a __le32 array.

Fix the one access of the DMA buffer (the check of the transaction code
of link packets) to work with big endian CPUs.  Also fix the two
accesses of the client bounce buffer (the reading of packet length).

4.)  Add a comment to the userspace ABI header that all of the data gets
out as little endian data, except for the timestamp which is CPU endian.
(We could make it little endian too, but why?  Vice versa, an ioctl
could be added to dump packet data in big endian byte order...)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Fix race between nosy_open() and remove_card() by replacing the
unprotected array of card pointers by a mutex-protected list of cards.

Make card instances reference-counted and let each client hold a
reference.

Notify clients about card removal via POLLHUP in poll()'s events
bitmap; also let read() fail with errno=ENODEV if the card was removed
and everything in the buffer was read.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

and add a missing pci_disable_device() to device shutdown.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Untested, I don't have a PCILynx CardBus card.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

nosy_start/stop_snoop() and nosy_add/remove_client() are simple enough
to be inlined into their callers.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

nosy_start/stop_snoop() are always only called by the ioctl method, i.e.
with IRQs enabled.  packet_handler() and bus_reset_handler() are always
only called by the IRQ handler.  Hence neither one needs to track IRQ
flags.

To underline the call context of packet_handler() and
bus_reset_handler(), rename these functions to *_irq_handler().
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

nosy_stop_snoop() would blow up the second time it was called without
nosy_start_snoop() in between.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

The required serialization of NOSY_IOC_START and NOSY_IOC_STOP is
already provided by the client_list_lock.

NOSY_IOC_FILTER does not really require serialization since accesses
to tcode_mask are atomic on any sane CPU architecture.  Nevertheless,
make it explicit that we want this to be atomic by means of
client_list_lock (which also surrounds the other tcode_mask access in
the IRQ handler).  While we are at it, change the type of tcode_mask to
u32 for consistency with the user API.

NOSY_IOC_GET_STATS does not require serialization against itself.  But
there is a bug here regarding concurrent updates of the two counters
by the IRQ handler.  Fix it by taking the client_list_lock in this ioctl
too.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Extend copyright note to 2007, c.f. Kristian's git log.

Includes:
  - replace some <asm/*.h> by <linux/*.h>
  - add required indirectly included <linux/spinlock.h>
  - order alphabetically

Coding style related changes:
  - change to utf8
  - normalize whitespace
  - normalize comment style
  - remove usages of __FUNCTION__
  - remove an unnecessary cast from void *

Const and static declarations:
  - driver_name is not const in pci_driver.name, drop const qualifier
  - driver_name can be taken from KBUILD_MODNAME
  - the global variable minors[] can and should be static
  - constify struct file_operations instance

Data types:
  - Remove unused struct member struct packet.code.  struct packet is
    only used for driver-internal bookkeeping; it does not appear on the
    wire or in DMA programs or the userspace ABI.  Hence the unused
    member .code can be removed without worries.

Preprocessor macros:
  - unroll a preprocessor macro that containd a return
  - use list_for_each_entry

Printk:
  - add missing terminating \n in some format strings
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

This adds the traffic sniffer driver for Texas Instruments PCILynx/
PCILynx2 based cards.  The use cases for nosy are analysis of
nonstandard protocols and as an aid in development of drivers,
applications, or firmwares.

Author of the driver is Kristian Høgsberg.  Known contributers are
Jody McIntyre and Jonathan Woithe.

Nosy programs PCILynx chips to operate in promiscuous mode, which is a
feature that is not found in OHCI-1394 controllers.  Hence, only special
hardware as mentioned in the Kconfig help text is suitable for nosy.

This is only the kernelspace part of nosy.  There is a userspace
interface to it, called nosy-dump, proposed to be added into the tools/
subdirectory of the kernel sources in a subsequent change.  Kernelspace
and userspave component of nosy communicate via a 'misc' character
device file called /dev/nosy with a simple ioctl() and read() based
protocol, as described by nosy-user.h.

The files added here are taken from
git://anongit.freedesktop.org/~krh/nosy commit ee29be97 (2009-11-10)
with the following changes by Stefan Richter:
  - Kconfig and Makefile hunks are written from scratch.
  - Commented out version printk in nosy.c.
  - Included missing <linux/sched.h>, reported by Stephen Rothwell.

"git shortlog nosy{-user.h,.c,.h}" from nosy's git repository:

Jonathan Woithe (2):
      Nosy updates for recent kernels
      Fix uninitialised memory (needed for 2.6.31 kernel)

Kristian Høgsberg (5):
      Pull over nosy from mercurial repo.
      Use a misc device instead.
      Add simple AV/C decoder.
      Don't break down on big payloads.
      Set parent device for misc device.

As a low-level IEEE 1394 driver, its files are placed into
drivers/firewire/ although nosy is not part of the firewire driver
stack.

I am aware of the following literature from Texas Instruments about
PCILynx programming:
      SCPA020A - PCILynx 1394 to PCI Bus Interface TSB12LV21BPGF
                 Functional Specification
      SLLA023  - Initialization and Asynchronous Programming of the
                 TSB12LV21A 1394 Device
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Kristian Høgsberg <krh@bitplanet.net>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  rtnetlink: make SR-IOV VF interface symmetric
  sctp: delete active ICMP proto unreachable timer when free transport
  tcp: fix MD5 (RFC2385) support

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  MIPS: Oprofile: Fix Loongson irq handler
  MIPS: N32: Use compat version for sys_ppoll.
  MIPS FPU emulator: allow Cause bits of FCSR to be writeable by ctc1

Now we have a set of nested attributes:

  IFLA_VFINFO_LIST (NESTED)
    IFLA_VF_INFO (NESTED)
      IFLA_VF_MAC
      IFLA_VF_VLAN
      IFLA_VF_TX_RATE

This allows a single set to operate on multiple attributes if desired.
Among other things, it means a dump can be replayed to set state.

The current interface has yet to be released, so this seems like
something to consider for 2.6.34.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

transport may be free before ICMP proto unreachable timer expire, so
we should delete active ICMP proto unreachable timer when transport
is going away.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TCP MD5 support uses percpu data for temporary storage. It currently
disables preemption so that same storage cannot be reclaimed by another
thread on same cpu.

We also have to make sure a softirq handler wont try to use also same
context. Various bug reports demonstrated corruptions.

Fix is to disable preemption and BH.
Reported-by: Bhaskar Dutta <bhaskie@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

    
    The interrupt enable bit for the performance counters is in the Control
    Register $24, not in the counter register.
    loongson2_perfcount_handler(), we need to use
Reported-by: Xu Hengyang <hengyang@mail.ustc.edu.cn>
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
    Cc: linux-mips@linux-mips.org
    Patchwork: http://patchwork.linux-mips.org/patch/1198/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

---

    
    The sys_ppoll() takes struct 'struct timespec'. This is different for the
    N32 and N64 ABIs. Use the compat version to do the proper conversions.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
    To: linux-mips@linux-mips.org
    Patchwork: http://patchwork.linux-mips.org/patch/1210/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

---

    
    In the FPU emulator code of the MIPS, the Cause bits of the FCSR register
    are not currently writeable by the ctc1 instruction.  In odd corner cases,
    this can cause problems.  For example, a case existed where a divide-by-zero
    exception was generated by the FPU, and the signal handler attempted to
    restore the FPU registers to their state before the exception occurred.  In
    this particular setup, writing the old value to the FCSR register would
    cause another divide-by-zero exception to occur immediately.  The solution
    is to change the ctc1 instruction emulator code to allow the Cause bits of
    the FCSR register to be writeable.  This is the behaviour of the hardware
    that the code is emulating.
    
    This problem was found by Shane McDonald, but the credit for the fix goes
    to Kevin Kissell.  In Kevin's words:
    
    I submit that the bug is indeed in that ctc_op:  case of the emulator.  The
    Cause bits (17:12) are supposed to be writable by that instruction, but the
    CTC1 emulation won't let them be updated by the instruction.  I think that
    actually if you just completely removed lines 387-388 [...] things would
    work a good deal better.  At least, it would be a more accurate emulation of
    the architecturally defined FPU.  If I wanted to be really, really pedantic
    (which I sometimes do), I'd also protect the reserved bits that aren't
    necessarily writable.
Signed-off-by: Shane McDonald <mcdonald.shane@gmail.com>
    To: anemo@mba.ocn.ne.jp
    To: kevink@paralogos.com
    To: sshtylyov@mvista.com
    Patchwork: http://patchwork.linux-mips.org/patch/1205/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

---

* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
  Btrfs: check for read permission on src file in the clone ioctl

mempool_alloc() can return null in atomic case.
Signed-off-by: Denis Kirjanov <kirjanov@gmail.com>
Cc: Joern Engel <joern@logfs.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

As we were using an internal dma flushing routine, this patch changes to
the DMA API flush_kernel_dcache_page().  Driver is able to compile now.

[akpm@linux-foundation.org: flush_kernel_dcache_page() comes before kunmap_atomic()]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The existing code would have allowed you to clone a file that was
only open for writing
Signed-off-by: Chris Mason <chris.mason@oracle.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
  JFS: Free sbi memory in error path
  fs/sysv: dereferencing ERR_PTR()
  Fix double-free in logfs
  Fix the regression created by "set S_DEAD on unlink()..." commit

Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf record: Add a fallback to the reference relocation symbol

I spotted the missing kfree() while removing the BKL.

[akpm@linux-foundation.org: avoid multiple returns so it doesn't happen again]
Signed-off-by: Jan Blunck <jblunck@suse.de>
Cc: Dave Kleikamp <shaggy@austin.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

I moved the dir_put_page() inside the if condition so we don't dereference
"page", if it's an ERR_PTR().
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

iput() is needed *until* we'd done successful d_alloc_root()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

1) i_flags simply doesn't work for mount/unlink race prevention;
we may have many links to file and rm on one of those obviously
shouldn't prevent bind on top of another later on.  To fix it
right way we need to mark _dentry_ as unsuitable for mounting
upon; new flag (DCACHE_CANT_MOUNT) is protected by d_flags and
i_mutex on the inode in question.  Set it (with dont_mount(dentry))
in unlink/rmdir/etc., check (with cant_mount(dentry)) in places
in namespace.c that used to check for S_DEAD.  Setting S_DEAD
is still needed in places where we used to set it (for directories
getting killed), since we rely on it for readdir/rmdir race
prevention.

2) rename()/mount() protection has another bogosity - we unhash
the target before we'd checked that it's not a mountpoint.  Fixed.

3) ancient bogosity in pivot_root() - we locked i_mutex on the
right directory, but checked S_DEAD on the different (and wrong)
one.  Noticed and fixed.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

* master.kernel.org:/home/rmk/linux-2.6-arm:
  ARM: 6126/1: ARM mpcore_wdt: fix build failure and other fixes
  ARM: 6125/1: ARM TWD: move TWD registers to common header
  ARM: 6110/1: Fix Thumb-2 kernel builds when UACCESS_WITH_MEMCPY is enabled
  ARM: 6112/1: Use the Inner Shareable I-cache and BTB ops on ARMv7 SMP
  ARM: 6111/1: Implement read/write for ownership in the ARMv6 DMA cache ops
  ARM: 6106/1: Implement copy_to_user_page() for noMMU
  ARM: 6105/1: Fix the __arm_ioremap_caller() definition in nommu.c

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86, mrst: Don't blindly access extended config space

If the kernel is large or the profiling step small, /proc/profile
leaks data and readprofile shows silly stats, until readprofile -r
has reset the buffer: clear the prof_buffer when it is vmalloc()ed.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

My old address will shut down in a couple of weeks: update the tree.
Signed-off-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Do not blindly access extended configuration space unless we actively
know we're on a Moorestown platform.  The fixed-size BAR capability
lives in the extended configuration space, and thus is not applicable
if the configuration space isn't appropriately sized.

This fixes booting certain VMware configurations with CONFIG_MRST=y.

Moorestown will add a fake PCI-X 266 capability to advertise the
presence of extended configuration space.
Reported-and-tested-by: Petr Vandrovec <petr@vandrovec.name>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Acked-by: Jacob Pan <jacob.jun.pan@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
LKML-Reference: <AANLkTiltKUa3TrKR1M51eGw8FLNoQJSLT0k0_K5X3-OJ@mail.gmail.com>

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86, cacheinfo: Turn off L3 cache index disable feature in virtualized environments
  x86, k8: Fix build error when K8_NB is disabled
  x86, amd: Check X86_FEATURE_OSVW bit before accessing OSVW MSRs
  x86: Fix fake apicid to node mapping for numa emulation

When running a quest kernel on xen we get:

BUG: unable to handle kernel NULL pointer dereference at 0000000000000038
IP: [<ffffffff8142f2fb>] cpuid4_cache_lookup_regs+0x2ca/0x3df
PGD 0
Oops: 0000 [#1] SMP
last sysfs file:
CPU 0
Modules linked in:

Pid: 0, comm: swapper Tainted: G        W  2.6.34-rc3 #1 /HVM domU
RIP: 0010:[<ffffffff8142f2fb>]  [<ffffffff8142f2fb>] cpuid4_cache_lookup_regs+0x
2ca/0x3df
RSP: 0018:ffff880002203e08  EFLAGS: 00010046
RAX: 0000000000000000 RBX: 0000000000000003 RCX: 0000000000000060
RDX: 0000000000000000 RSI: 0000000000000040 RDI: 0000000000000000
RBP: ffff880002203ed8 R08: 00000000000017c0 R09: ffff880002203e38
R10: ffff8800023d5d40 R11: ffffffff81a01e28 R12: ffff880187e6f5c0
R13: ffff880002203e34 R14: ffff880002203e58 R15: ffff880002203e68
FS:  0000000000000000(0000) GS:ffff880002200000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000038 CR3: 0000000001a3c000 CR4: 00000000000006f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process swapper (pid: 0, threadinfo ffffffff81a00000, task ffffffff81a44020)
Stack:
 ffffffff810d7ecb ffff880002203e20 ffffffff81059140 ffff880002203e30
<0> ffffffff810d7ec9 0000000002203e40 000000000050d140 ffff880002203e70
<0> 0000000002008140 0000000000000086 ffff880040020140 ffffffff81068b8b
Call Trace:
 <IRQ>
 [<ffffffff810d7ecb>] ? sync_supers_timer_fn+0x0/0x1c
 [<ffffffff81059140>] ? mod_timer+0x23/0x25
 [<ffffffff810d7ec9>] ? arm_supers_timer+0x34/0x36
 [<ffffffff81068b8b>] ? hrtimer_get_next_event+0xa7/0xc3
 [<ffffffff81058e85>] ? get_next_timer_interrupt+0x19a/0x20d
 [<ffffffff8142fa23>] get_cpu_leaves+0x5c/0x232
 [<ffffffff8106a7b1>] ? sched_clock_local+0x1c/0x82
 [<ffffffff8106a9a0>] ? sched_clock_tick+0x75/0x7a
 [<ffffffff8107748c>] generic_smp_call_function_single_interrupt+0xae/0xd0
 [<ffffffff8101f6ef>] smp_call_function_single_interrupt+0x18/0x27
 [<ffffffff8100a773>] call_function_single_interrupt+0x13/0x20
 <EOI>
 [<ffffffff8143c468>] ? notifier_call_chain+0x14/0x63
 [<ffffffff810295c6>] ? native_safe_halt+0xc/0xd
 [<ffffffff810114eb>] ? default_idle+0x36/0x53
 [<ffffffff81008c22>] cpu_idle+0xaa/0xe4
 [<ffffffff81423a9a>] rest_init+0x7e/0x80
 [<ffffffff81b10dd2>] start_kernel+0x40e/0x419
 [<ffffffff81b102c8>] x86_64_start_reservations+0xb3/0xb7
 [<ffffffff81b103c4>] x86_64_start_kernel+0xf8/0x107
Code: 14 d5 40 ff ae 81 8b 14 02 31 c0 3b 15 47 1c 8b 00 7d 0e 48 8b 05 36 1c 8b
 00 48 63 d2 48 8b 04 d0 c7 85 5c ff ff ff 00 00 00 00 <8b> 70 38 48 8d 8d 5c ff
 ff ff 48 8b 78 10 ba c4 01 00 00 e8 eb
RIP  [<ffffffff8142f2fb>] cpuid4_cache_lookup_regs+0x2ca/0x3df
 RSP <ffff880002203e08>
CR2: 0000000000000038
---[ end trace a7919e7f17c0a726 ]---

The L3 cache index disable feature of AMD CPUs has to be disabled if the
kernel is running as guest on top of a hypervisor because northbridge
devices are not available to the guest. Currently, this fixes a boot
crash on top of Xen. In the future this will become an issue on KVM as
well.

Check if northbridge devices are present and do not enable the feature
if there are none.

[ hpa: backported to 2.6.34 ]
Signed-off-by: Frank Arnold <frank.arnold@amd.com>
LKML-Reference: <1271945222-5283-3-git-send-email-bp@amd64.org>
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: <stable@kernel.org>

K8_NB depends on PCI and when the last is disabled (allnoconfig) we fail
at the final linking stage due to missing exported num_k8_northbridges.
Add a header stub for that.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <20100503183036.GJ26107@aftab>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: <stable@kernel.org>