The Allwinner A20 has an ethernet controller that seems to be
an early version of Synopsys DesignWare MAC 10/100/1000 Universal,
which is supported by the stmmac driver.

Allwinner's GMAC requires setting additional registers in the SoC's
clock control unit.

The exact version of the DWMAC IP that Allwinner uses is unknown,
thus the exact feature set is unknown.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The stmmac driver core allows passing feature flags and callbacks via
platform data. Add a similar stmmac_of_data to pass flags and callbacks
tied to compatible strings. This allows us to extend stmmac with glue
layers for different SoCs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The snps,phy-addr device tree property is non-standard, and should be
removed in favor of proper phy node support. Remove it from the binding
documents and warn if the property is still used.

Most PHYs respond to address 0, but a few don't, so auto-detect PHY
address by default, to make up for the lack of explicit address selection.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

"snps,force_sf_dma_mode" is documented in stmmac device tree bindings,
but is never handled by the driver.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

stmmac callbacks have been extended for better separation.
Update them to avoid breakage.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current .init and .exit callbacks requires access to driver
private data structures. This is not a good seperation and abstraction.

Instead, we add a new .setup callback for allocating private data, and
pass the returned pointer to the other callbacks.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The DWMAC has a reset assert line, which is used on some SoCs. Add an
optional reset control to stmmac driver core.

To support reset control deferred probing, this patch changes the driver
probe function to return the actual error, instead of just -EINVAL.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The stmmac driver does not enable the main clock during the probe phase.
If the clock was not enabled by the boot loader or was disabled by the
kernel, hardware features and the MDIO bus would not be probed properly.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Though described as required, the "phy-handle" property for the DaVinci EMAC
binding is actually optional, as the driver will happily function without it,
assuming 100/FULL link; the property is not specified  either in the example
device node,  or in the actual EMAC device nodes for DA850 and AM3517 device
trees.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When I create a new namespace with 'ip netns add net0', or add/remove
new links in a namespace with 'ip link add/delete type veth', rx/tx
queues events can be got in all namespaces. That is because rx/tx queue
ktypes do not have namespace support, and their kobj parents are setted to
NULL. This patch is to fix it.
Reported-by: Libo Chen <chenlibo@huawei.com>
Signed-off-by: Libo Chen <chenlibo@huawei.com>
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is not actually implemented.

Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To silent "make htmldocs" warning.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The commit 91705c61 ("net: sctp: trivial: update mailing list
address") updated almost all the SCTP mailing list address from

	"lksctp-developers@lists.sourceforge.net"
to
	"linux-sctp@vger.kernel.org"

except for the one in include/linux/sctp.h file. Fix this way trivial
one so that all is updated.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Cc: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6_link_dev_addr sorts newly added addresses by scope in
ifp->addr_list. Smaller scope addresses are added to the tail of the
list. Use this fact to iterate in reverse over addr_list and break out
as soon as a higher scoped one showes up, so we can spare some cycles
on machines with lot's of addresses.

The ordering of the addresses is not relevant and we are more likely to
get the eui64 generated address with this change anyway.
Suggested-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Code should avoid needless exports, don't export something unless it used.
Make local functions static and remove unused stubs.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previous patch changed prototypes, but forgot functions.
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

We currently don't report IPV6_RECVPKTINFO in cmsg access ancillary data
for IPv4 datagrams on IPv6 sockets.

This patch splits the ip6_datagram_recv_ctl into two functions, one
which handles both protocol families, AF_INET and AF_INET6, while the
ip6_datagram_recv_specific_ctl only handles IPv6 cmsg data.

ip6_datagram_recv_*_ctl never reported back any errors, so we can make
them return void. Also provide a helper for protocols which don't offer dual
personality to further use ip6_datagram_recv_ctl, which is exported to
modules.

I needed to shuffle the code for ping around a bit to make it easier to
implement dual personality for ping ipv6 sockets in future.
Reported-by: Gert Doering <gert@space.net>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace some magic numbers which describe states of 4-state model
loss generator with enumerate.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With the introduction of IPV6_FL_F_REFLECT, there is no guarantee of
flow label unicity. This patch introduces a new sysctl to protect the old
behaviour, enable by default.

Changelog of V3:
 * rename ip6_flowlabel_consistency to flowlabel_consistency
 * use net_info_ratelimited()
 * checkpatch cleanups
Signed-off-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This information is already available via IPV6_FLOWINFO
of IPV6_2292PKTOPTIONS, and them a filtering to get the flow label
information. But it is probably logical and easier for users to add this
here, and to control both sent/received flow label values with the
IPV6_FLOWLABEL_MGR option.
Signed-off-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

With this option, the socket will reply with the flow label value read
on received packets.

The goal is to have a connection with the same flow label in both
direction of the communication.

Changelog of V4:
 * Do not erase the flow label on the listening socket. Use pktopts to
 store the received value
Signed-off-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace some dev_kfree_skb() with kfree_skb() calls when
we drop one skb, this might help bug tracking.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a follow-up patch to f3d33426 ("net: rework recvmsg
handler msg_name and msg_namelen logic").

DECLARE_SOCKADDR validates that the structure we use for writing the
name information to is not larger than the buffer which is reserved
for msg->msg_name (which is 128 bytes). Also use DECLARE_SOCKADDR
consistently in sendmsg code paths.
Signed-off-by: Steffen Hurrle <steffen@hurrle.net>
Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

For user space packet capturing libraries such as libpcap, there's
currently only one way to check which BPF extensions are supported
by the kernel, that is, commit aa1113d9 ("net: filter: return
-EINVAL if BPF_S_ANC* operation is not supported"). For querying all
extensions at once this might be rather inconvenient.

Therefore, this patch introduces a new option which can be used as
an argument for getsockopt(), and allows one to obtain information
about which BPF extensions are supported by the current kernel.

As David Miller suggests, we do not need to define any bits right
now and status quo can just return 0 in order to state that this
versions supports SKF_AD_PROTOCOL up to SKF_AD_PAY_OFFSET. Later
additions to BPF extensions need to add their bits to the
bpf_tell_extensions() function, as documented in the comment.
Signed-off-by: Michal Sekletar <msekleta@redhat.com>
Cc: David Miller <davem@davemloft.net>
Reviewed-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
	net/ipv4/tcp_metrics.c

Overlapping changes between the "don't create two tcp metrics objects
with the same key" race fix in net and the addition of the destination
address in the lookup key in net-next.

Minor overlapping changes in bnx2x driver.
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) The value choosen for the new SO_MAX_PACING_RATE socket option on
    parisc was very poorly choosen, let's fix it while we still can.
    From Eric Dumazet.

 2) Our generic reciprocal divide was found to handle some edge cases
    incorrectly, part of this is encoded into the BPF as deep as the JIT
    engines themselves.  Just use a real divide throughout for now.
    From Eric Dumazet.

 3) Because the initial lookup is lockless, the TCP metrics engine can
    end up creating two entries for the same lookup key.  Fix this by
    doing a second lookup under the lock before we actually create the
    new entry.  From Christoph Paasch.

 4) Fix scatter-gather list init in usbnet driver, from Bjørn Mork.

 5) Fix unintended 32-bit truncation in cxgb4 driver's bit shifting.
    From Dan Carpenter.

 6) Netlink socket dumping uses the wrong socket state for timewait
    sockets.  Fix from Neal Cardwell.

 7) Fix netlink memory leak in ieee802154_add_iface(), from Christian
    Engelmayer.

 8) Multicast forwarding in ipv4 can overflow the per-rule reference
    counts, causing all multicast traffic to cease.  Fix from Hannes
    Frederic Sowa.

 9) via-rhine needs to stop all TX queues when it resets the device,
    from Richard Weinberger.

10) Fix RDS per-cpu accesses broken by the this_cpu_* conversions.  From
    Gerald Schaefer.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  s390/bpf,jit: fix 32 bit divisions, use unsigned divide instructions
  parisc: fix SO_MAX_PACING_RATE typo
  ipv6: simplify detection of first operational link-local address on interface
  tcp: metrics: Avoid duplicate entries with the same destination-IP
  net: rds: fix per-cpu helper usage
  e1000e: Fix compilation warning when !CONFIG_PM_SLEEP
  bpf: do not use reciprocal divide
  be2net: add dma_mapping_error() check for dma_map_page()
  bnx2x: Don't release PCI bars on shutdown
  net,via-rhine: Fix tx_timeout handling
  batman-adv: fix batman-adv header overhead calculation
  qlge: Fix vlan netdev features.
  net: avoid reference counter overflows on fib_rules in multicast forwarding
  dm9601: add USB IDs for new dm96xx variants
  MAINTAINERS: add virtio-dev ML for virtio
  ieee802154: Fix memory leak in ieee802154_add_iface()
  net: usbnet: fix SG initialisation
  inet_diag: fix inet_diag_dump_icsk() to use correct state for timewait sockets
  cxgb4: silence shift wrapping static checker warning

Aaron Brown says:

====================
Intel Wired LAN Driver Updates

This series contains updates from Emil to ixgbevf.

He cleans up the code by removing the adapter structure as a
parameter from multiple functions in favor of using the ixgbevf_ring
structure and moves hot-path specific statistic int the ring
structure for anticipated performance gains.

He also removes the Tx/Rx counters for checksum offload and adds
counters for tx_restart_queue and tx_timeout_count.

Next he makes it so that the first tx_buffer structure acts as a
central storage location for most the skb info we are about to
transmit, then takes advantage of the dma buffer always being
present in the first descriptor and mapped as single allowing a
call to dma_unmap_single which alleviates the need to check for
DMA mapping in ixgbevf_clean_tx_irq().

Finally he merges the ixgbevf_tx_map call and the ixgbevf_tx_queue
call into a single function.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This change merges the ixgbevf_tx_map call and the ixgbevf_tx_queue call
into a single function.  In order to make room for this setting of cmd_type
and olinfo flags is done in separate functions.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch takes advantage of the dma buffer always being present in the
first descriptor and mapped as single. As such we can call dma_unmap_single
and don't need to check for DMA mapping in ixgbevf_clean_tx_irq().

In addition this patch makes use of the DMA API.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change makes it so that the first tx_buffer structure acts as a
central storage location for most of the info about the skb we are about
to transmit.

In addition this patch makes tx_flags part of the ixgbevf_tx_buffer struct.
This allows us to use the flags directly from the stucture and as result
removes the tx_flags parameter from some functions. Also as a cleanup
mapped_as_page is folded into tx_flags and some unused flags were removed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds counters for tx_restart_queue and tx_timeout_count.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes the Tx/Rx counters for checksum offload.

The Tx counter was never updated and the Rx counter is of limited use.
This is in effort to clean up the counters and make them consistent
with the counters shown by ixgbe.

Also this patch removes some members of the adapter structure that were
never used and shuffles others to reduce number of holes.

before:
	/* size: 1568, cachelines: 25, members: 48 */
	/* sum members: 1519, holes: 10, sum holes: 43 */
	/* padding: 6 */
	/* last cacheline: 32 bytes */

after:
	/* size: 1480, cachelines: 24, members: 43 */
	/* sum members: 1479, holes: 1, sum holes: 1 */
	/* last cacheline: 8 bytes */
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch moves hot-path specific statistics into the ring structure.
This allows us to drop the adapter structure in some functions and should
help with performance.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch cleans up the code by removing the adapter structure as
parameter from multiple functions. The adapter structure was previously
being used to access the dev pointer, but this can also be done via the
ixgbevf_ring structure. This way we can drop the adapter as parameter from
these functions.

This patch also includes small cleanups in some error code paths.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Aaron Brown says:

====================
Intel Wired LAN Driver Updates

This series contains updates to i40e.

Neerav implements DCB and DCBNL support and adds DCB options
to Kconfig.  DCB is disabled by default.

Anjali refactors flow control director to fix inconsistencies
that were preventing clean unloads of the driver, move the
queues for handling flow director error into their own hardware
VSI and implement a corrected version of the basic ethtool add
ntuple rule.

Jesse provides fixes for a compiler warning, firmware workaround,
white space fixes and renames some defines.

Shannon reworks the device ID #defines to follow the
DEV_ID_ convention followed by our other drivers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

It's now built as a separate utility module, and enabling BT selects
that module in Kconfig. This fixes:

net/ieee802154/built-in.o:(___ksymtab_gpl+lowpan_process_data+0x0): multiple definition of `__ksymtab_lowpan_process_data'
net/bluetooth/built-in.o:(___ksymtab_gpl+lowpan_process_data+0x0): first defined here
net/ieee802154/built-in.o:(___ksymtab_gpl+lowpan_header_compress+0x0): multiple definition of `__ksymtab_lowpan_header_compress'
net/bluetooth/built-in.o:(___ksymtab_gpl+lowpan_header_compress+0x0): first defined here
net/ieee802154/built-in.o: In function `lowpan_header_compress':
net/ieee802154/6lowpan_iphc.c:606: multiple definition of `lowpan_header_compress'
net/bluetooth/built-in.o:/home/swarren/shared/git_wa/kernel/kernel.git/net/bluetooth/../ieee802154/6lowpan_iphc.c:606: first defined here
net/ieee802154/built-in.o: In function `lowpan_process_data':
net/ieee802154/6lowpan_iphc.c:344: multiple definition of `lowpan_process_data'
net/bluetooth/built-in.o:/home/swarren/shared/git_wa/kernel/kernel.git/net/bluetooth/../ieee802154/6lowpan_iphc.c:344: first defined here
make[1]: *** [net/built-in.o] Error 1

(this change probably simply wasn't "git add"d to a53d34c3)

Fixes: a53d34c3 ("net: move 6lowpan compression code to separate module")
Fixes: 18722c24 ("Bluetooth: Enable 6LoWPAN support for BT LE devices")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rework the device ID #defines to follow the _DEV_ID convention
already established in the other Intel drivers.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow compiling DCB related files if I40E_DCB option
is supported in the kernel configuration.

DCB is disabled by default.
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Tested-By: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds capability to configure DCB on i40e network
interfaces using Intel XL710 adapter firmware APIs.

By default all VSIs are only enabled for the default traffic
class enabled by firmware for any given PF. The driver would
query the firmware for the traffic classes that are enabled for
the port and reconfigure the LAN VSI to match to the port traffic
class settings. All other VSIs are only enabled for the default
traffic class settings for now.

The driver registers and listens to firmware events that may
require change in the DCB settings. It may reconfigure the VSI
settings based on these events.

This patch exposes IEEE DCBNL interfaces for the i40e driver to
allow any application to query the DCB settings on the adapter.
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-By: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Intel XL710 series of adapters support QoS as per the
IEEE 802.1 DCB (Data Center Bridging) standard.
This is supported in conjuction with:
- Enhanced Transmission Selection (ETS) - IEEE 802.1Qaz
- Priority Flow Control (PFC) - IEEE 802.1Qbb
- DCB eXchange Protocol (DCBX) - IEEE 802.1Qaz

On Intel XL710 adapters DCBX is performed by the adapter
firmware. The firmware runs DCBX in willing mode and configures
the port as per the DCB settings recommended by it's link
partner.

By default in absence of any DCBX; firmware would configure the
port with a single traffic class and all of the port bandwith
will be allocated to that traffic class.

This patch adds functions and calls to support querying and
configuring DCB using firmware APIs.
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-By: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>