This patch does 2 things (bad, I know -- but they're both pretty small
and pretty obscure).

The CBI specification states in section 2.4.3.1.3 that

	... the host shall also issue Clear Feature for Endpoint Halt
	to the Bulk In pipe if the device reports that the Data In
	command block has Failed.

along with a note in section 2.5.3 that Data Out commands should work
analogously.  This patch does that, along with cleaning up the status
detection logic a little.

For Bulk-only transfers we currently ignore the dResidue field in the CSW,
except for reporting it (without byte-swapping!) in a debug message.  The
patch uses it to compute the residue value returned to the SCSI layer.
Note that the Bulk-only spec allows devices to transfer more data than
they actually use (i.e., they may add padding or ignore stuff) and then
inform the host of this by means of the dResidue value.  The logic used is
simple: our reported residue is the larger of what the device claims and
what we didn't transfer, except that it can't be larger than the total
transfer length.

This patch updates the sdd09 subdriver to make it return Command Failure
with appropriate sense data (rather than Tranport Error) when:

	a MODE-SENSE command requests an unsupported page;

	a CDB includes an unrecognized command code.

This should help prevent confusion and excessive retrying by the SCSI
drivers.

I know Linus is not taking cleanups at this point, but perhaps
you can delete it in your tree. Seems like someone (Oliver?)
fixed all the garbage in old printer.c, so the comment is not
needed anymore.

I reviewed changes, and usblp.c looks correct. I'm doing backport
to 2.4 for Fedora right now.

Just for cdc-acm, it pushes RX URB processing into a tasklet;
and has minor cleanups.

I cc'd Vojtech since he's this driver's maintainer.  If this
checks out, usb-serial will need similar changes.


p.s. the issue is a WARN_ON that tells us:

   >> [<c012046c>] local_bh_enable+0x8c/0x90
   >> [<f8991452>] ppp_asynctty_receive+0x62/0xb0 [ppp_async]
   >> [<c02144f3>] flush_to_ldisc+0xa3/0x120
   >> [<f891f20f>] acm_read_bulk+0xbf/0x140 [cdc_acm]
   >> [<c02684c9>] usb_hcd_giveback_urb+0x29/0x50
   >> [<c027670c>] dl_done_list+0x11c/0x130
   >> [<c0277075>] ohci_irq+0x85/0x170
   >> [<c0268526>] usb_hcd_irq+0x36/0x60
   >> [<c010aeba>] handle_IRQ_event+0x3a/0x70
   >> [<c010b227>] do_IRQ+0x97/0x140
   >> [<c0109624>] common_interrupt+0x18/0x20

into kroah.com:/home/greg/linux/BK/usb-new_drivers-2.6

into kroah.com:/home/greg/linux/BK/usb-new_drivers-2.6

into home.osdl.org:/home/torvalds/v2.5/linux

The pid_alive() check within the loop is incorrect.  If we are within
the tasklist lock and the thread group leader is valid then the thread
chain will be fully intact.

Instead, the check should be _outside_ the loop, since if the group
leader no longer exists, the whole list is gone and we must not try
to access it.

Move the check around, and add comment.

Bug-hunting and fix by Srivatsa Vaddagiri

When doing sync wakeups we must not skip the notification of other cpus
if the task is not on this runqueue.

We need to initialize st->state in tcp_seq_start().  Otherwise
tcp_seq_stop() is run with previous st->state, and it calls the unneeded
unlock etc, causing a kernel crash.

I've got a lot more changes than what's included here.  I've put this
down to the bear minimum to get things working sanely.

Mainly, I just want to get all the people hit by this a chance to use
2.6.0 without having to get our tree. Changes itemized:

 - Fix deadlock possibility in csr.c:read_maps()
 - Fix kmalloc to use ATOMIC in highlevel.c.
 - s/in_interrupt/irqs_disabled/ in ieee1394_transactions.c to fix
   warnings when transactions occured.
 - Introduce a release callback for the host driver and use it correctly.
 - Reorganize the nodemgr probe so we do an initial scan to discover
   devices, check IRM/CycleMaster, then do a final full probe when things
   are kosher. Fixes a problem where device registration and hotplug
   would cause some serious problems when a bus reset was forced in the
   middle of the probe.

into home.osdl.org:/home/torvalds/v2.5/linux

into home.osdl.org:/home/torvalds/v2.5/linux

into home.osdl.org:/home/torvalds/v2.5/linux

There are /proc handles there setup by proc_tty_register_driver, but there is
no module ownership association, so anything that reads after module unload
will blow.

The trivial fix is to propagate the owner of tty_driver to proc entry.

This fixes a small, but important bug in smsc-ircc2.c.

Without this the driver tries release the same region twice.

      Tracked down by Rohit Seth.

Do not special case ENOMEM as an error code, we should free up
the packet for all errors.

Most of the breakage came from cset 1.838.10.3

The br_netfilter_{init,fini}() calls need to be guarded by
BRIDGE_NETFILTER, from Michal Janusz Miroslaw.

When bringing an interface down do not forget to clear the
IF_RS_SENT and IF_RA_RCVD flags.

into home.osdl.org:/home/torvalds/v2.5/linux

This fixes an oops that can occur if JFS is used as the root filesystem.

Writes to a device node may cause a ->write_inode to be called during a
read-only mount.  JFS needs to check for NULL log in jfs_flush_journal. 

into home.osdl.org:/home/torvalds/v2.5/linux

Also, make sure NET_RX_DROP is returned if we did not accept the
packet.

In implementations that use no socket locking, such as RAW sockets,
once we queue the SKB to the socket another cpu can remove the SKB
from the socket queue and free up the SKB making the skb->len access
touch freed memory.

Based upon a report from Burton Windle, kernel bugzilla #937

into home.osdl.org:/home/torvalds/v2.5/linux

Also add some ServerWorks-specific tweaks.