We try to call free_netvsc_device(net_device) when "net_device" is NULL.
It leads to an Oops.

Fixes: f90251c8 ('hyperv: Increase the buffer length for netvsc_channel_cb()')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2014-09-04

This series contains updates to i40e, i40evf, ixgbe and ixgbevf.

Catherine adds dual speed module support to i40e.  Updates i40e to allow
the user to change link settings when the link is down.

Serey renames i40e_ndo_set_vf_spoofck() to i40e_ndo_set_vf_spookchk()
to be more consistent with what is defined in netdev and removes a
unnecessary variable assignment.

Jesse makes a malicious driver detection warning only print if extended
driver string is enabled for i40e.  Fixes a panic under traffic load when
resetting or if/whenever there was a Tx-timeout because we were enabling
the Tx queue to early.

Anjali fixes an issue when PF reset fails, where we were trying to restart
the admin queue which has not been setup at that point.  This resolves an
occasional kernel panic when PF reset fails for some reason.

Ethan Zhao replaces the use of a local i40e_vfs_are_assigned() with the
global kernel pci_vfs_assigned() for i40e.

Alex cleans up the FDB handling for ixgbe.  This change makes it so that
the behavior for FDB handling is consistent between both the SR-IOV and
non-SR-IOV cases.  The main change is that we perform bounds checking on
the number of SR-IOV addresses regardless of if SR-IOV is enabled or not
as we can only support a certain number of addresses in the hardware.

Emil extends the pending Tx work check to the VF interfaces, where the
driver initiates a reset of the interface on link loss with pending Tx
work in order to clear the rings.  Introduces a delay for 82599 VFs of
at least 500 usecs to make sure the VFLINKS value is correct, since this
bit tends to flap when a DA or SFP+ cable is disconnected.

Jacob adds code comments in ixgbe to make it more obvious that we are
resetting features based on the fact that we do not have MSI-X enabled,
and cannot use the previous settings.  Also resolves a kernel NULL
pointer dereference by limiting the combined total of MACVLAN and
SR-IOV VFs, since the hardware has a limited number of pools available
(64).  Previously, no checks were in place to limit the number of
accelerated MACVLAN devices based on the number of pools, which would
be ok since there was already a limit for these well below the number of
available pools.  However, SR-IOV uses the very same pools, therefore
we need to ensure that the total number of pools does not exceed the
number of pools available in the hardware.

v2:
 - clean up code comment in patch 5 by replacing "an" with "auto
   negotiation" based on feedback from Sergei Shtylyov
 - removed un-necessary parenthesis around function call in patch 8
   based on feedback from Sergei Shtylyov
====================

Simplify the interrupt resource lookup code in cpsw_probe() by the
following:

 * Only look at the first member of the resource. As the driver only
   works for DT-enabled platforms anyway, a resource of type
   IORESOURCE_IRQ will only contain one single entry
   (res->start == res->end), so there is no need for the iteration.

 * Add a bounds check to avoid overflows if we are passed more than
   ARRAY_SIZE(priv->irqs_table) resources.

 * Assign 'ret' with the return value of devm_request_irq() so that
   cpsw_probe() returns the appropriate error code.

 * If devm_request_irq() fails, report the error code in the log
   message.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

nh_exceptions is effectively used under rcu, but lacks proper
barriers. Between kzalloc() and setting of nh->nh_exceptions(),
we need a proper memory barrier.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 4895c771 ("ipv4: Add FIB nexthop exceptions.")
Signed-off-by: David S. Miller <davem@davemloft.net>

This syntax error was covered by L2TP_REFCNT_DEBUG not being set by
default.
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tom Lendacky says:

====================
amd-xgbe: AMD XGBE driver updates 2014-09-03

The following series of patches includes fixes/updates to the driver.

- Query the device for the actual speed mode (KR/KX) rather than trying
  to track it
- Update parallel detection logic to support KR mode
- Fix new warnings from checkpatch in the amd-xgbe and amd-xgbe-phy
  driver

This patch series is based on net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch contains fixes identified by checkpatch when run with the
strict option.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch contains fixes identified by checkpatch when run with the
strict option.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support to allow parallel detection to work in KR speed. With
both speed modes of KX and KR supported, KX must be checked first.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since device resets can change the current mode it's possible to think
the device is in a different mode than it actually is.  Rather than
trying to determine every place that is needed to set/save the current
mode, be safe and check the devices actual mode when needed rather than
trying to track it.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hayes Wang says:

====================
r8152: random MAC address

If the interface has invalid MAC address, it couldn't
be used. In order to let it work normally, give a
random one.

v3:
  Remove
	ether_addr_copy(dev->perm_addr, dev->dev_addr);

v2:
  Use "%pM" format specifier for printing a MAC address.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If the hw doesn't have a valid MAC address, give a random one and
set it to the hw.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Exchange the location of rtl8152_set_mac_address() and
set_ethernet_addr(). Then, the set_ethernet_addr() could
set the MAC address by calling rtl8152_set_mac_address()
later.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Govindarajulu Varadarajan says:

====================
enic: Add support for rx_copybreak

The following series implements rx_copybreak.

dma_map_single()/dma_unmap_single() is more expensive than alloc_skb & memcpy
for smaller packets. By doing this we can reuse the dma buff which is already
mapped. This is very useful when iommu is on. The default skb copybreak value
is 256.

When iommu is on, we can go much higher than 256. All the drivers that supports
rx_copybreak provides module parameter to change this value. Since module
parameter is the least preferred way for changing driver values, this series
adds ethtool support for setting rx_copybreak.

v4:
Validate tunable length in ethtool_get_tunable, not in driver implemented
function.

Loose tunable_ops array for each tunable type. Define one function and let the
driver use switch case for each type.

Use double underscore for data type in UAPI headers.
Use const qualifier where possible.

v3:
Add tunable namespace to ethtool. Use new ethtool cmd ETHTOOL_S/GTUNABLE to
set/get rx_copybreak from userspace.

v2:
Add new ethtool_cmd for DMA buffer parameters, instead of adding new members to
existing ethtool_ringparam.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for setting/getting rx_copybreak using
generic ethtool tunable.

Defines enic_get_tunable() & enic_set_tunable() to get/set rx_copybreak.
As of now, these two function supports only rx_copybreak.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds new ethtool cmd, ETHTOOL_GTUNABLE & ETHTOOL_STUNABLE for getting
tunable values from driver.

Add get_tunable and set_tunable to ethtool_ops. Driver implements these
functions for getting/setting tunable value.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Calling dma_map_single()/dma_unmap_single() is quite expensive compared
to copying a small packet. So let's copy short frames and keep the buffers
mapped.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Marcel reported to see the following message when autoloading
is being triggered when adding nlmon device:

  Loading kernel module for a network device with
  CAP_SYS_MODULE (deprecated). Use CAP_NET_ADMIN and alias
  netdev-nlmon instead.

This false-positive happens despite with having correct
capabilities set, e.g. through issuing `ip link del dev nlmon`
more than once on a valid device with name nlmon, but Marcel
has also seen it on creation time when no nlmon module is
previously compiled-in or loaded as module and the device
name equals a link type name (e.g. nlmon, vxlan, team).

Stephen says:

  The netdev module alias is a hold over from the past. For
  normal devices, people used to create a alias eth0 to and
  point it to the type of network device used, that was back
  in the bad old ISA days before real discovery.

  Also, the tunnels create module alias for the control device
  and ip used to use this to autoload the tunnel device.

  The message is bogus and should just be removed, I also see
  it in a couple of other cases where tap devices are renamed
  for other usese.

As mentioned in 8909c9ad ("net: don't allow CAP_NET_ADMIN
to load non-netdev kernel modules"), we nevertheless still
might want to leave the old autoloading behaviour in place
as it could break old scripts, so for now, lets just remove
the log message as Stephen suggests.

Reference: http://thread.gmane.org/gmane.linux.kernel/1105168Reported-by: Marcel Holtmann <marcel@holtmann.org>
Suggested-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With eBPF getting more extended and exposure to user space is on it's way,
hardening the memory range the interpreter uses to steer its command flow
seems appropriate.  This patch moves the to be interpreted bytecode to
read-only pages.

In case we execute a corrupted BPF interpreter image for some reason e.g.
caused by an attacker which got past a verifier stage, it would not only
provide arbitrary read/write memory access but arbitrary function calls
as well. After setting up the BPF interpreter image, its contents do not
change until destruction time, thus we can setup the image on immutable
made pages in order to mitigate modifications to that code. The idea
is derived from commit 314beb9b ("x86: bpf_jit_comp: secure bpf jit
against spraying attacks").

This is possible because bpf_prog is not part of sk_filter anymore.
After setup bpf_prog cannot be altered during its life-time. This prevents
any modifications to the entire bpf_prog structure (incl. function/JIT
image pointer).

Every eBPF program (including classic BPF that are migrated) have to call
bpf_prog_select_runtime() to select either interpreter or a JIT image
as a last setup step, and they all are being freed via bpf_prog_free(),
including non-JIT. Therefore, we can easily integrate this into the
eBPF life-time, plus since we directly allocate a bpf_prog, we have no
performance penalty.

Tested with seccomp and test_bpf testsuite in JIT/non-JIT mode and manual
inspection of kernel_page_tables.  Brad Spengler proposed the same idea
via Twitter during development of this patch.

Joint work with Hannes Frederic Sowa.
Suggested-by: Brad Spengler <spender@grsecurity.net>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When we bring the interface down, phy_stop() will schedule the PHY
state machine to call our link adjustment callback. By the time we do so,
we may have clock gated off the SYSTEMPORT hardware block, and this will
cause bus errors to happen in bcm_sysport_adj_link():

Make sure that we only touch the UMAC_CMD register when there is an
actual link. This is safe to do for two reasons:

- updating the Ethernet MAC registers only make sense when a physical
  link is present
- the PHY library state machine first set phydev->link = 0 before
  invoking phydev->adjust_link in the PHY_HALTED case

This is a similar fix to the GENET one:
c677ba8b ("net: bcmgenet: update
UMAC_CMD only when link is detected").

Fixes: 80105bef ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As in IPv6 people might increase the igmp query robustness variable to
make sure unsolicited state change reports aren't lost on the network. Add
and document this new knob to igmp code.

RFCs allow tuning this parameter back to first IGMP RFC, so we also use
this setting for all counters, including source specific multicast.

Also take over sysctl value when upping the interface and don't reuse
the last one seen on the interface.

Cc: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a new sysctl_mld_qrv knob to configure the mldv1/v2 query
robustness variable. It specifies how many retransmit of unsolicited mld
retransmit should happen. Admins might want to tune this on lossy links.

Also reset mld state on interface down/up, so we pick up new sysctl
settings during interface up event.

IPv6 certification requests this knob to be available.

I didn't make this knob netns specific, as it is mostly a setting in a
physical environment and should be per host.

Cc: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hardware has a limited number of pools available (64). Previously, no
checks were in place to limit the number of accelerated macvlan devices
based on the number of pools. Normally this would be ok, because there
was already a limit for these well below the number of available pools.
However, SR-IOV uses the very same pools. Therefor, we need to ensure
that the total number of pools (number of VFs plus the number of non-VF
pools in use for accelerated macvlans) does not exceed the number of
pools available in hardware.

This patch resolves a kernel NULL pointer dereference caused by the following commands:

$modprobe ixgbe max_vfs=63

$ethtool -K eth2 l2-fwd-offload on

$ip link add link eth2 macvlan0 type macvlan

$ip link set dev macvlan0 up

[  992.950080] BUG: unable to handle kernel NULL pointer dereference at 0000000000000056
[  992.951109] IP: [<ffffffffa003b71e>] ixgbe_disable_fwd_ring+0x1e/0xf0 [ixgbe]
[  992.951684] PGD 22a80e067 PUD 232e9b067 PMD 0
[  992.952389] Oops: 0000 [#1] SMP
[  992.953014] Modules linked in: nfsd lockd nfs_acl exportfs auth_rpcgss oid_registry sunrpc bridge stp llc vhost_net macvtap macvlan vhost tun kvm_intel kvm ioatdma ixgbe mdio igb dca
[  992.956042] CPU: 2 PID: 11928 Comm: ifconfig Not tainted 3.16.0-rc6-net-next-07-29-2014-FCoE+ #1
[  992.956915] Hardware name: Intel Corporation S2600CO/S2600CO, BIOS SE5C600.86B.02.03.0003.041920141333 04/19/2014
[  992.957791] task: ffff8804341c0000 ti: ffff8801d7dc8000 task.ti: ffff8801d7dc8000
[  992.958660] RIP: 0010:[<ffffffffa003b71e>]  [<ffffffffa003b71e>] ixgbe_disable_fwd_ring+0x1e/0xf0 [ixgbe]
[  992.959613] RSP: 0018:ffff8801d7dcbbb8  EFLAGS: 00010286
[  992.960093] RAX: 0000000000000001 RBX: 0000000000000000 RCX: 0000000000000001
[  992.960575] RDX: ffff880232eb7000 RSI: 0000000000000000 RDI: ffff88022dc05800
[  992.961059] RBP: ffff8801d7dcbbd8 R08: 0000000000000000 R09: 0000000000000000
[  992.961541] R10: 0000000000000001 R11: 0000000000000000 R12: ffff88022ec20980
[  992.962023] R13: ffff880232eb7000 R14: 0000000000000001 R15: 0000000000000001
[  992.962508] FS:  00007fab264887a0(0000) GS:ffff880237640000(0000) knlGS:0000000000000000
[  992.963378] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  992.963858] CR2: 0000000000000056 CR3: 000000022a939000 CR4: 00000000001427e0
[  992.964340] Stack:
[  992.964806]  ffff88022ec28840 ffff88022ec20980 ffff88022dc05800 ffff880232eb7000
[  992.965976]  ffff8801d7dcbc28 ffffffffa003bae8 ffff8801d7dcbbe8 0000000000000400
[  992.967147]  000000000000000d ffff88022ec20980 ffff88022ec20000 ffff88022dc05800
[  992.968319] Call Trace:
[  992.968795]  [<ffffffffa003bae8>] ixgbe_fwd_ring_up+0x88/0x280 [ixgbe]
[  992.969284]  [<ffffffffa0041d83>] ixgbe_fwd_add+0x173/0x220 [ixgbe]
[  992.969767]  [<ffffffffa015056c>] macvlan_open+0x1bc/0x230 [macvlan]
[  992.970256]  [<ffffffff816b8de7>] __dev_open+0xd7/0x150
[  992.970735]  [<ffffffff816b8bd7>] __dev_change_flags+0xa7/0x170
[  992.971220]  [<ffffffff816b8ccb>] dev_change_flags+0x2b/0x70
[  992.971703]  [<ffffffff817471b2>] devinet_ioctl+0x602/0x6d0
[  992.972184]  [<ffffffff81748168>] inet_ioctl+0x78/0x90
[  992.972666]  [<ffffffff816a143b>] sock_do_ioctl+0x2b/0x70
[  992.973146]  [<ffffffff816a14ed>] sock_ioctl+0x6d/0x260
[  992.973627]  [<ffffffff811ad3b4>] do_vfs_ioctl+0x84/0x540
[  992.974109]  [<ffffffff811a4c81>] ? final_putname+0x21/0x50
[  992.974593]  [<ffffffff818725d5>] ? sysret_check+0x22/0x5d
[  992.975073]  [<ffffffff811ad901>] SyS_ioctl+0x91/0xa0
[  992.975550]  [<ffffffff818725a9>] system_call_fastpath+0x16/0x1b
[  992.976026] Code: ff 66 66 66 2e 0f 1f 84 00 00 00 00 00 55 48 89 e5 48 83 ec 20 48 89 5d e8 4c 89 65 f0 48 89 f3 4c 89 6d f8 4c 8b a7 08 02 00 00 <44> 0f b6 6e 56 44 03 af 14 02 00 00 4c 89 e7 e8 5e f2 ff ff be
[  992.982261] RIP  [<ffffffffa003b71e>] ixgbe_disable_fwd_ring+0x1e/0xf0 [ixgbe]
[  992.983212]  RSP <ffff8801d7dcbbb8>
[  992.983681] CR2: 0000000000000056
[  992.984248] ---[ end trace 9f54802b5cc3638b ]---

Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Since we previously called ixgbe_set_num_queues just prior to attempting
to set our interrupt scheme, it may be non obvious why we have to call
it again inside the function. Add a comment which helps make it more
obvious that we are resetting features based on the fact that we do not
have MSI-X enabled, and cannot use the previous settings.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

VFLINKS.LINKUP bit tends to flap when a DA or SFP+ cable is disconnected.
It can take up to 500 usecs for the LINKUP bit to be correct.

This patch resolves the issue by introducing a delay for 82599 VFs of at
least 500 usecs to make sure the VFLINKS value is correct.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe initiates a reset of the interface on link loss with pending Tx work
in order to clear the rings.

This patch extends the pending Tx work check to the VF interfaces with the
same purpose.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it so that the behavior for FDB handling is consistent
between both the SR-IOV and non-SR-IOV cases.  The main change here is that we
perform bounds checking on the number of SR-IOV addresses regardless of if
SR-IOV is enabled or not as we can only support a certain number of addresses
in the hardware.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

There is global funcion pci_vfs_assigned(), so use it instead of composing
local one.
Signed-off-by: Ethan Zhao <ethan.kernel@gmail.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Bump i40e version to 1.0.11 and i40evf version to 1.0.5.

Change-ID: I63a60fa2efe82aae87a8a3095f43218db57d46ce
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>

This fixes the panic under traffic load when resetting.  This issue
could also show up if/whenever there is a Tx-timeout.

Change-ID: Ie393a1f17fd5d962e56fc3bfe784899ef25402f5
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

We shouldn't restart Admin queue subtask if PF reset fails since we do
not have the AQ setup at that point. This patch makes sure we disable AQ
clean subtask when PF reset fails.

This will resolve an occasional kernel panic when PF reset fails for
some reason.

Change-ID: I11a747773362a8c5c0ad7a10cd34be0bda8eb9e8
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver is un-necessarily printing a warning that is only marginally
useful to the user.  Make the warning only print if extended driver
string printing is enabled, other messages related to a reset event
will still continue to print.

Change-ID: I5e8beca6516a2f176cd2e72b0ac2b3b909e6c953
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Since we don't seem to be getting an LSE telling us link is going down
during set_phy_config (but we do get an LSE telling us we are coming
back up), fake one for the OS and tell them link is going down. Also
do an atomic restart no matter what because there are times the user
may want to end with link up even if they started with link down (like
if they accidentally set it to a speed that can't link and are trying to
fix it).

Change-ID: I0a642af9c1d0feb67bce741aba1a9c33bd349ed6
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove unnecessary setting of "ret" variable as it's already set at
the top of the function.

Change-ID: Icaccfc67f335817a23579b7c43625d59ad6c9925
Signed-off-by: Serey Kong <serey.kong@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Change "spoofck" to "spoofchk" to be consistent with as defined in netdev.

Change-ID: I9866d6284cb5f92c8d71dc0776c6d1e71dfb62a5
Signed-off-by: Serey Kong <serey.kong@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Allow the user to change auto-negotiation and speed settings if
link is down.

Change-ID: I372967c627682b5e1835f623a7cbf41b21b51043
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Now that fw has implemented dual speed module support, we can add ours.
Also, add the phy type for 1G LR/SR and set its media type to fiber.
Lastly, instead of a WARN_ON if the phy type is not recognized just print
a warning.

Change-ID: I2e5227d4a8c2907b0ed423038e5dbce774e466b0
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

It would appear the mlx4_en driver was still making a call to
dev_kfree_skb_any() where dev_consume_skb_any() would be more
appropriate.  This should make dropped packet profiling/tracking
easier/better over a NIC driven by mlx4_en.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Although rhashtable library allows user to specify a quiet big size
for user's created hash table, the table may be shrunk to a
very small size - HASH_MIN_SIZE(4) after object is removed from
the table at the first time. Subsequently, even if the total amount
of objects saved in the table is quite lower than user's initial
setting in a long time, the hash table size is still dynamically
adjusted by rhashtable_shrink() or rhashtable_expand() each time
object is inserted or removed from the table. However, as
synchronize_rcu() has to be called when table is shrunk or
expanded by the two functions, we should permit user to set the
minimum table size through configuring the minimum number of shifts
according to user specific requirement, avoiding these expensive
actions of shrinking or expanding because of calling synchronize_rcu().
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 50cbe9ab ("net: Validate xmit SKBs right when we
pull them out of the qdisc") the validation code was moved out of
dev_hard_start_xmit and into dequeue_skb.

However this overlooked the fact that we do not always enqueue
the skb onto a qdisc. First situation is if qdisc have flag
TCQ_F_CAN_BYPASS and qdisc is empty.  Second situation is if
there is no qdisc on the device, which is a common case for
software devices.

Originally spotted and inital patch by Alexander Duyck.
As a result Alex was seeing issues trying to connect to a
vhost_net interface after commit 50cbe9ab was applied.

Added a call to validate_xmit_skb() in __dev_xmit_skb(), in the
code path for qdiscs with TCQ_F_CAN_BYPASS flag, and in
__dev_queue_xmit() when no qdisc.

Also handle the error situation where dev_hard_start_xmit() could
return a skb list, and does not return dev_xmit_complete(rc) and
falls through to the kfree_skb(), in that situation it should
call kfree_skb_list().

Fixes:  50cbe9ab ("net: Validate xmit SKBs right when we pull them out of the qdisc")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>