Current implementation of init_vudc_hw() adds ep0 to ep_list
and then after looping through all endpoints removes it from
that list.

As this may be misleading let's refactor this function
and avoid adding and removing ep0 to eplist and place it
immediately in correct place.

In addition let's remove redundant 0 assignments as ep
array is zeroed during allocation.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ep_list inside gadget structure doesn't contain ep0.
It is stored separately in ep0 field.

This causes an urb hang if gadget driver decides to
delay setup handling. On host side this is visible as
timeout error when setting configuration.

This bug can be reproduced using for example any gadget
with mass storage function.

Fixes: abdb2957 ("usbip: vudc: Add vudc_transfer")
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'usb-serial-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next

Johan writes:

USB-serial updates for v4.10-rc1

These updates include a new driver for Fintek F8153x devices, support
for the GPIO functionality on CP2105 devices, and improved support for
CH34X devices.

Included are also some clean ups and fixes for various minor issues.
Signed-off-by: Johan Hovold <johan@kernel.org>

Function klsi_105_open() calls usb_control_msg() (to "enable read") and
checks its return value. When the return value is unexpected, it only
assigns the error code to the return variable retval, but does not
terminate the exception path. This patch fixes the bug by inserting
"goto err_generic_close;" when the call to usb_control_msg() fails.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Pan Bian <bianpan2016@163.com>
[johan: rebase on prerequisite fix and amend commit message]
Signed-off-by: Johan Hovold <johan@kernel.org>

Kill urbs and disable read before returning from open on failure to
retrieve the line state.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

The comment says function wa_nep_queue() should return 0 if ok, and <0
errno code on error. However, its implementation always returns 0, even
if the call to kzalloc() fails. As a result, the return value may be
inconsistent with the execution status, which may mislead the callers.
This patch fixes the bug, returning -ENOMEM when the call to kzalloc()
fails.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In function __wa_xfer_setup_segs(), variable result takes the return
value. Its value should be a negative errno on failures. Because result
may be reassigned in a loop, and its value is guaranteed to be not less
than 0 during the following repeats of the loop. So when the call to
kmalloc() or usb_alloc_urb() fails in the loop, the value of variable
result may be 0 (indicates no error), which is inconsistent with the
execution status. This patch fixes the bug, initializing variable result
with -ENOMEM in the loop.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In function wusb_dev_sec_add(), variable result takes the return value.
Its value should be negative on failures. When function krealloc() is
called, an earlier check of variable result guarantees that the value of
result must not be less than "sizeof(*secd)", and result is not
reassigned when krealloc() returns a NULL pointer. As a result, a
positive value may be returned, which makes it impossible for the caller
of wusb_dev_sec_add() to detect the error. This patch fixes the bug by
assigning -ENOMEM to result when krealloc() returns NULL.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The ehci_w90x900_probe function is not doing anything other than
calling usb_w90x900_probe function so ehci_w90x900_probe function
is unuseful that is why removed ehci_w90x900_probe functions and
renamed usb_w90x900_probe function to ehci_w90x900_probe for proper
naming.

The ehci_w90x900_remove function is also not doing anything other
than calling usb_w90x900_remove that is why removed ehci_w90x900_remove
function and renamed usb_w90x900_remove to ehci_w90x900_remove for proper
naming.

This also removes warning of checkpatch.pl script.
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Allows configuring Samsung's s3c2410 USB OHCI controller using a
devicetree.
Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Adds the device tree bindings description for Samsung S3C2410 and
compatible USB OHCI controller.
Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The da8xx ohci controller is not working after suspend and resume.

This is because only the root hub is being resumed.

Balance the ohci_suspend of the suspend path with an ohci_resume
in the resume path so that we resume the entire controller, and not
just the root hub.

Also, while we are here, remove setting device power_state,
as this is no longer needed and scheduled for removal
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds the compatible string to the ohci driver
to be able to probe from DT
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch documents the device tree bindings required for
the ohci controller found in TI da8xx family of SoC's

Cc: robh+dt@kernel.org
Cc: mark.rutland@arm.com
Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Using a regulator to handle VBUS will eliminate the need for
platform data and callbacks, and make the driver more generic
allowing different types of regulators to handle VBUS.

The regulator equivalents to the platform callbacks are:
    set_power   ->  regulator_enable/regulator_disable
    get_power   ->  regulator_is_enabled
    get_oci     ->  regulator_get_error_flags
    ocic_notify ->  regulator event notification
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

To migrate to a DT based boot, we will remove the use of platform
callbacks, in favor of using the regulator framework to handle
vbus and over current.

In preparation to use a regulator instead of callbacks, move the platform
data callbacks into separate functions. This provides well defined place
to for the regulator API to coexist with the platform callbacks before
all users are converted.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Instead of global variables, use the extra_priv_size of
the ohci driver.

We cannot yet move the ocic mask because this is used on
the interrupt handler which is registered through platform
data and does not have an hcd pointer. This will be moved
on a later patch.
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver is for Fintek F81532/F81534 USB to Serial Ports IC.

F81532 spec:
https://drive.google.com/file/d/0B8vRwwYO7aMFOTRRMmhWQVNvajQ/view?usp=
sharing

F81534 spec:
https://drive.google.com/file/d/0B8vRwwYO7aMFV29pQWJqbVBNc00/view?usp=
sharing

Features:
1. F81532 is 1-to-2 & F81534 is 1-to-4 serial ports IC
2. Support Baudrate from B50 to B115200.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>

Merge tag 'usb-ci-v4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next

Peter writes:

- Adding ULPI PHY support for imx53
- Properly mark little endian descriptors for udc

Merge tag 'extcon-next-for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into usb-nextx

Chanwoo writes:

Update extcon for 4.10

Detailed description for this pull request:
- The extcon-usb-gpio driver supports the VBUS detection with USB ID and VBUS pin.

Merge tag 'phy-for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next

Kishon writes:

phy: for 4.10

Merge contains:
 *) Add new usb2 phy driver for Meson8b and GXBB
 *) Remove phy drivers added for miphy365 and STiH415/6 (as support for
    these SoCs are removed from the kernel)
 *) Add a sysfs entry to facilitate usb role swap in rcar SoC
 *) Add support for otg port in rk3399
 *) misc fixes in various phy drivers and cleanups
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

We want the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull IOMMU fixes from David Woodhouse:
 "Two minor fixes.

  The first fixes the assignment of SR-IOV virtual functions to the
  correct IOMMU unit, and the second fixes the excessively large (and
  physically contiguous) PASID tables used with SVM"

* git://git.infradead.org/intel-iommu:
  iommu/vt-d: Fix PASID table allocation
  iommu/vt-d: Fix IOMMU lookup for SR-IOV Virtual Functions

Pull MIPS fixes from Ralf Baechle:
 "Another round of MIPS fixes for 4.9:

   - Fix unreadable output in __do_page_fault due to the KERN_CONT
     patchset

   - Correctly handle MIPS R6 fixes to the c0_wired register"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: mm: Fix output of __do_page_fault
  MIPS: Mask out limit field when calculating wired entry count

Pull vfs splice fix from Al Viro.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fix default_file_splice_read()

Botched calculation of number of pages.  As the result,
we were dropping pieces when doing splice to pipe from
e.g. 9p.
Reported-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull i2c fixes from Wolfram Sang:
 "Here is a revert and two bugfixes for the I2C designware driver.

  Please note that we are still hunting down a regression for the
  i2c-octeon driver. While there is a fix pending, we have unclear
  feedback from the testers currently. An rc8 would be quite helpful
  for this case"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  Revert "i2c: designware: do not disable adapter after transfer"
  i2c: designware: fix rx fifo depth tracking
  i2c: designware: report short transfers

Pull ARM fix from Russell King:
 "This resolves the ksyms issues by reverting the commit which
  introduced the breakage"

There was what I consider to be a better fix, but it's late in the rc
game, so I'll take the revert.

* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
  Revert "arm: move exports to definitions"

Pull networking fixes from David Miller:

 1) Fix leak in fsl/fman driver, from Dan Carpenter.

 2) Call flow dissector initcall earlier than any networking driver can
    register and start to use it, from Eric Dumazet.

 3) Some dup header fixes from Geliang Tang.

 4) TIPC link monitoring compat fix from Jon Paul Maloy.

 5) Link changes require EEE re-negotiation in bcm_sf2 driver, from
    Florian Fainelli.

 6) Fix bogus handle ID passed into tfilter_notify_chain(), from Roman
    Mashak.

 7) Fix dump size calculation in rtnl_calcit(), from Zhang Shengju.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (26 commits)
  tipc: resolve connection flow control compatibility problem
  mvpp2: use correct size for memset
  net/mlx5: drop duplicate header delay.h
  net: ieee802154: drop duplicate header delay.h
  ibmvnic: drop duplicate header seq_file.h
  fsl/fman: fix a leak in tgec_free()
  net: ethtool: don't require CAP_NET_ADMIN for ETHTOOL_GLINKSETTINGS
  tipc: improve sanity check for received domain records
  tipc: fix compatibility bug in link monitoring
  net: ethernet: mvneta: Remove IFF_UNICAST_FLT which is not implemented
  dwc_eth_qos: drop duplicate headers
  net sched filters: fix filter handle ID in tfilter_notify_chain()
  net: dsa: bcm_sf2: Ensure we re-negotiate EEE during after link change
  bnxt: do not busy-poll when link is down
  udplite: call proper backlog handlers
  ipv6: bump genid when the IFA_F_TENTATIVE flag is clear
  net/mlx4_en: Free netdev resources under state lock
  net: revert "net: l2tp: Treat NET_XMIT_CN as success in l2tp_eth_dev_xmit"
  rtnetlink: fix the wrong minimal dump size getting from rtnl_calcit()
  bnxt_en: Fix a VXLAN vs GENEVE issue
  ...

Pull libnvdimm fixes from Dan Williams:

 - Fix a crash that occurs at driver initialization if the memory region
   is already busy (request_mem_region() fails).

 - Fix a vma validation check that mistakenly allows a private device-
   dax mapping to be established. Device-dax explicitly forbids private
   mappings so it can guarantee a given fault granularity and backing
   memory type.

 Both of these fixes have soaked in -next and are tagged for -stable.

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  device-dax: fail all private mapping attempts
  device-dax: check devm_nsio_enable() return value

Pull KVM fixes from Radim Krčmář:
 "Four fixes for bugs found by syzkaller on x86, all for stable"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: x86: check for pic and ioapic presence before use
  KVM: x86: fix out-of-bounds accesses of rtc_eoi map
  KVM: x86: drop error recovery in em_jmp_far and em_ret_far
  KVM: x86: fix out-of-bounds access in lapic

Pull powerpc fixes from Michael Ellerman:
 "Fixes marked for stable:
   - Set missing wakeup bit in LPCR on POWER9
   - Fix the early OPAL console wrappers
   - Fixup kernel read only mapping

  Fixes for code merged this cycle:
   - Fix missing CRCs, add more asm-prototypes.h declarations"

* tag 'powerpc-4.9-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/mm: Fixup kernel read only mapping
  powerpc/boot: Fix the early OPAL console wrappers
  powerpc: Fix missing CRCs, add more asm-prototypes.h declarations
  powerpc: Set missing wakeup bit in LPCR on POWER9

In commit 10724cc7 ("tipc: redesign connection-level flow control")
we replaced the previous message based flow control with one based on
1k blocks. In order to ensure backwards compatibility the mechanism
falls back to using message as base unit when it senses that the peer
doesn't support the new algorithm. The default flow control window,
i.e., how many units can be sent before the sender blocks and waits
for an acknowledge (aka advertisement) is 512. This was tested against
the previous version, which uses an acknowledge frequency of on ack per
256 received message, and found to work fine.

However, we missed the fact that versions older than Linux 3.15 use an
acknowledge frequency of 512, which is exactly the limit where a 4.6+
sender will stop and wait for acknowledge. This would also work fine if
it weren't for the fact that if the first sent message on a 4.6+ server
side is an empty SYNACK, this one is also is counted as a sent message,
while it is not counted as a received message on a legacy 3.15-receiver.
This leads to the sender always being one step ahead of the receiver, a
scenario causing the sender to block after 512 sent messages, while the
receiver only has registered 511 read messages. Hence, the legacy
receiver is not trigged to send an acknowledge, with a permanently
blocked sender as result.

We solve this deadlock by simply allowing the sender to send one more
message before it blocks, i.e., by a making minimal change to the
condition used for determining connection congestion.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

gcc-7 detects a short memset in mvpp2, introduced in the original
merge of the driver:

drivers/net/ethernet/marvell/mvpp2.c: In function 'mvpp2_cls_init':
drivers/net/ethernet/marvell/mvpp2.c:3296:2: error: 'memset' used with length equal to number of elements without multiplication by element size [-Werror=memset-elt-size]

The result seems to be that we write uninitialized data into the
flow table registers, although we did not get any warning about
that uninitialized data usage.

Using sizeof() lets us initialize then entire array instead.

Fixes: 3f518509 ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Drop duplicate header delay.h from mlx5/core/main.c.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Acked-by: Matan Barak <matanb@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Drop duplicate header delay.h from adf7242.c.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Acked-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Drop duplicate header seq_file.h from ibmvnic.c.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We set "tgec->cfg" to NULL before passing it to kfree().  There is no
need to set it to NULL at all.  Let's just delete it.

Fixes: 57ba4c9b ("fsl/fman: Add FMan MAC support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ETHTOOL_GLINKSETTINGS command is deprecating the ETHTOOL_GSET
command and likewise it shouldn't require the CAP_NET_ADMIN capability.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>