* 'for-linus' of git://gitserver.sunplusct.com/linux-2.6-score:
  score: Use generic show_interrupts()
  score: Convert to new irq function names
  score: lost a semicolon in asm/irqflags.h
  score: Select GENERIC_HARDIRQS_NO_DEPRECATED
  score: Convert irq_chip to new functions

The acpi video driver attempts to explicitly create a sysfs link between
the acpi device and the associated PCI device. However, we're now also
doing this from the backlight core, which means that we get a backtrace
caused by a duplicate file. Remove the code and leave it up to the
backlight core.
Reported-by: Jeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Alessandro Suardi <alessandro.suardi@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2: (39 commits)
  Treat writes as new when holes span across page boundaries
  fs,ocfs2: Move o2net_get_func_run_time under CONFIG_OCFS2_FS_STATS.
  ocfs2/dlm: Move kmalloc() outside the spinlock
  ocfs2: Make the left masklogs compat.
  ocfs2: Remove masklog ML_AIO.
  ocfs2: Remove masklog ML_UPTODATE.
  ocfs2: Remove masklog ML_BH_IO.
  ocfs2: Remove masklog ML_JOURNAL.
  ocfs2: Remove masklog ML_EXPORT.
  ocfs2: Remove masklog ML_DCACHE.
  ocfs2: Remove masklog ML_NAMEI.
  ocfs2: Remove mlog(0) from fs/ocfs2/dir.c
  ocfs2: remove NAMEI from symlink.c
  ocfs2: Remove masklog ML_QUOTA.
  ocfs2: Remove mlog(0) from quota_local.c.
  ocfs2: Remove masklog ML_RESERVATIONS.
  ocfs2: Remove masklog ML_XATTR.
  ocfs2: Remove masklog ML_SUPER.
  ocfs2: Remove mlog(0) from fs/ocfs2/heartbeat.c
  ocfs2: Remove mlog(0) from fs/ocfs2/slot_map.c
  ...

Fix up trivial conflict in fs/ocfs2/super.c

When a hole spans across page boundaries, the next write forces
a read of the block. This could end up reading existing garbage
data from the disk in ocfs2_map_page_blocks. This leads to
non-zero holes. In order to avoid this, mark the writes as new
when the holes span across page boundaries.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.de>
Signed-off-by: jlbec <jlbec@evilplan.org>

When CONFIG_DEBUG_FS=y and CONFIG_OCFS2_FS_STATS=n, we get the
following warning:

fs/ocfs2/cluster/tcp.c:213:16: warning: ‘o2net_get_func_run_time’
defined but not used

Since o2net_get_func_run_time is only called from
o2net_update_recv_stats, so move it under CONFIG_OCFS2_FS_STATS.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: jlbec <jlbec@evilplan.org>

* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
  NFS: Ensure that rpc_release_resources_task() can be called twice.
  NFS: Don't leak RPC clients in NFSv4 secinfo negotiation
  NFS: Fix a hang in the writeback path

Stephen ran into the following build error:

  drivers/mfd/cs5535-mfd.c:30:22: error: asm/olpc.h: No such file or directory

olpc.h exists only on x86 (and in the future, ARM).  Rather than
wrapping the include in an #ifdef, just change cs5535-mfd to only build
on x86.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In commit 95a0f10c ("drbd: store in-core bitmap little endian,
regardless of architecture") drbd had made the sane choice to use
little-endian bitmap functions everywhere.  However, it used the
horrible old functions names from <asm-generic/bitops/le.h>, that were
never really meant to be exported.

In the meantime, things got cleaned up, and in commit c4945b9e
("asm-generic: rename generic little-endian bitops functions") we
renamed the LE bitops to something sane, exactly so that they could be
used in random code without people gouging their eyes out when seeing
the crazy jumble of letters that were the old internal names.

As a result the drbd thing merged cleanly (commit 8d49a775: "Merge
branch 'for-2.6.39/drivers' of git://git.kernel.dk/linux-2.6-block"),
since there was no data conflict - but the end result obviously doesn't
actually compile.
Reported-and-tested-by: Ingo Molnar <mingo@elte.hu>
Cc: Jens Axboe <jaxboe@fusionio.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Chen Liqin <liqin.chen@sunplusct.com>

Scripted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Chen Liqin <liqin.chen@sunplusct.com>

All chips converted and proper accessor functions used.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Chen Liqin <liqin.chen@sunplusct.com>

Use the proper accessor functions in show_interrupts() while at it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Chen Liqin <liqin.chen@sunplusct.com>

Merge branch 'irq-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'irq-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  tile: Use generic show_interupts()
  tile: Convert to new irq function names
  dma: Ipu: Convert interupt code

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
  regulator: Add MODULE_DEVICE_TABLE to max8997 and max8998
  regulator: fix tps6524x section mismatch
  regulator: Remove more wm831x-specific IRQ operations
  regulator: add ab8500 enable and raise time delays
  regulator: provide consumer interface for fall/rise time
  regulator: add set_voltage_time_sel infrastructure
  regulator: initialization for ab8500 regulators
  regulator: add support for USB voltage regulator
  regulator: switch the ab3100 to use enable_time()
  Regulator: add suspend-finish API for regulator core.
  regulator: fix typo in Kconfig
  regulator: Convert WM831x regulators to genirq
  regulator: If we fail when setting up a supply say which supply

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: Fix yet another race in disconnection
  ALSA: asihpi - Update verbose debug print macros
  ALSA: asihpi - Improve non-busmaster adapter operation
  ALSA: asihpi - Support single-rate no-SRC cards
  ALSA: HDA: New AD1984A model for Dell Precision R5500
  ALSA: vmalloc buffers should use normal mmap
  ALSA: hda - Fix SPDIF out regression on ALC889
  ALSA: usb-audio - Support for Boss JS-8 Jam Station
  ALSA: usb-audio: add Cakewalk UM-1G support
  sound/oss/opl3: validate voice and channel indexes
  sound/oss: remove offset from load_patch callbacks

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
  mfd: Clean up max8997 IRQ namespace
  mfd: Fold irq_set_chip/irq_set_handler
  mfd: Cleanup irq namespace
  mfd: twl6030: Cleanup interrupt handling
  mfd: twl4030: Cleanup interrupt handling
  mfd: mx8925: Remove irq_desc leftovers
  mfd: htc-i2cpld: Cleanup interrupt handling
  mfd: htc-egpio: Cleanup interrupt handling
  mfd: ezx-pcap: Remvove open coded irq handling
  mfd: 88pm860x: Remove unused irq_desc leftovers
  mfd: asic3: Cleanup irq handling
  mfd: Select MFD_CORE if TPS6105X driver is configured
  mfd: Add MODULE_DEVICE_TABLE to rdc321x-southbridge
  mfd: Add MAX8997/8966 IRQ control
  mfd: Constify i2c_device_id tables
  mfd: OLPC: Clean up names to match what OLPC actually uses
  mfd: Add mfd_clone_cell(), convert cs5535-mfd/olpc-xo1 to it

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging:
  hwmon: (pmbus) Fix temperature limit register access

Merge branch 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6

* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
  hwspinlock: depend on OMAP4
  ARM: OMAP2+: Fix warnings for GPMC interrupt
  OMAP4: PandaBoard: remove unused power regulators
  arm: mach-omap2: omap_l3_smx: fix irq handler setup
  arm: mach-omap2: devices: fix omap3_l3_init() return value

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  staging: Fix bdops->check_events() misconversion in cyasblkdev_block.c
  ide: ensure that we re-run the queue handler

* 'for-2.6.39/drivers' of git://git.kernel.dk/linux-2.6-block: (122 commits)
  cciss: fix lost command issue
  drbd: need include for bitops functions declarations
  Revert "cciss: Add missing allocation in scsi_cmd_stack_setup and  corresponding deallocation"
  cciss: fix missed command status value CMD_UNABORTABLE
  cciss: remove unnecessary casts
  cciss: Mask off error bits of c->busaddr in cmd_special_free when calling pci_free_consistent
  cciss: Inform controller we are using 32-bit tags.
  cciss: hoist tag masking out of loop
  cciss: Add missing allocation in scsi_cmd_stack_setup and  corresponding deallocation
  cciss: export resettable host attribute
  drbd: drop code present under #ifdef which is relevant to 2.6.28 and below
  drbd: Fixed handling of read errors on a 'VerifyS' node
  drbd: Fixed handling of read errors on a 'VerifyT' node
  drbd: Implemented real timeout checking for request processing time
  drbd: Remove unused function atodb_endio()
  drbd: improve log message if received sector offset exceeds local capacity
  drbd: kill dead code
  drbd: don't BUG_ON, if bio_add_page of a single page to an empty bio fails
  drbd: Removed left over, now wrong comments
  drbd: serialize admin requests for new verify run with pending bitmap io
  ...

* 'docs-next' of git://git.lwn.net/linux-2.6:
  docs: update the development process document
  docs: fix dev_debug() braino in dynamic-debug-howto.txt

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  hwmon: (f71882fg) Add support for the F71889A
  hwmon: (f71882fg) Add support for the F81865F
  hwmon: (f71882fg) Document all supported devices
  hwmon: (f71882fg) Per-chip fan/temperature input count tables
  hwmon: (f71882fg) Secure chip property definition arrays

* 'for-linus-1' of git://git.infradead.org/mtd-2.6: (49 commits)
  mtd: mtdswap: fix compilation warning
  mtdswap: kill strict error handling option
  mtd: nand: enable software BCH ECC in nand simulator
  mtd: nand: add software BCH ECC support
  mtd: fix printf format warnings, mostly lack of %zd for size_t, in mtdswap
  mtd: sm_rtl: check kmalloc return value
  mtd: cfi: add support for AMIC flashes (e.g. A29L160AT)
  lib: add shared BCH ECC library
  mtd: mxc_nand: fix OOB corruption when page size > 2KiB
  mtd: DaVinci: Removed header file that is not required
  mtd: pxa3xx_nand: clean the keep configure code
  mtd: pxa3xx_nand: mtd scan id process could be defined by driver itself
  mtd: pxa3xx_nand: unify prepare command
  mtd: pxa3xx_nand: discard wait_for_event,write_cmd,__readid function
  mtd: pxa3xx_nand: rework irq logic
  mtd: pxa3xx_nand: make scan procedure more clear
  mtd: speedtest: fix integer overflow
  mtd: mxc_nand: fix read past buffer end
  mtd: omap3: nand: report corrected ecc errors
  jffs2: remove a trailing white space in commentaries
  ...

I no longer have access to any hardware that uses APM and have not
provided real maintenance for several years.  Hopefully someone with the
hardware or energy will step forward if the driver is to be kept.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-and-appreciated-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix fsl_rio.c kernel-doc warning: no exported symbols as
requested by !E are found:

  Warning(arch/powerpc/sysdev/fsl_rio.c): no structured comments found
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

DocBook/v4l/ no longer has any *.png files, so the 'cp' command fails,
breaking the build.  Drop the *.png cp.

  cp: cannot stat `linux-2.6.38-git18/Documentation/DocBook/v4l/*.png': No such file or directory
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix inode.c kernel-doc fatal error: 2 comment sections have the same name:

  Error(fs/inode.c:1171): duplicate section name 'Note'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix ipc/util.c kernel-doc warnings:

  Warning(ipc/util.c:336): No description found for parameter 'ns'
  Warning(ipc/util.c:620): No description found for parameter 'ns'
  Warning(ipc/util.c:790): No description found for parameter 'ns'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Reviewed-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix mm/memory.c incorrect kernel-doc function notation:

  Warning(mm/memory.c:3718): Cannot understand  * @access_remote_vm - access another process' address space
   on line 3718 - I thought it was a doc line
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Omit the segment prefix in the UP case. GS is not used then
and we will generate segfaults if cmpxchg16b is used otherwise.
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When m_start returns an error, the seq_file logic will still call m_stop
with that error entry, so we'd better make sure that we check it before
using it as a vma.

Introduced by commit ec6fd8a4 ("report errors in /proc/*/*map*
sanely"), which replaced NULL with various ERR_PTR() cases.

(On ia64, you happen to get a unaligned fault instead of a page fault,
since the address used is generally some random error code like -EPERM)
Reported-by: Anca Emanuel <anca.emanuel@gmail.com>
Reported-by: Tony Luck <tony.luck@intel.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Américo Wang <xiyou.wangcong@gmail.com>
Cc: Stephen Wilson <wilsons@start.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

BUG: atomic_dec_and_test(): -1: atomic counter underflow at:
Pid: 2827, comm: mount.nfs Not tainted 2.6.38 #1
Call Trace:
 [<ffffffffa02223a0>] ? put_rpccred+0x44/0x14e [sunrpc]
 [<ffffffffa021bbe9>] ? rpc_ping+0x4e/0x58 [sunrpc]
 [<ffffffffa021c4a5>] ? rpc_create+0x481/0x4fc [sunrpc]
 [<ffffffffa022298a>] ? rpcauth_lookup_credcache+0xab/0x22d [sunrpc]
 [<ffffffffa028be8c>] ? nfs_create_rpc_client+0xa6/0xeb [nfs]
 [<ffffffffa028c660>] ? nfs4_set_client+0xc2/0x1f9 [nfs]
 [<ffffffffa028cd3c>] ? nfs4_create_server+0xf2/0x2a6 [nfs]
 [<ffffffffa0295d07>] ? nfs4_remote_mount+0x4e/0x14a [nfs]
 [<ffffffff810dd570>] ? vfs_kern_mount+0x6e/0x133
 [<ffffffffa029605a>] ? nfs_do_root_mount+0x76/0x95 [nfs]
 [<ffffffffa029643d>] ? nfs4_try_mount+0x56/0xaf [nfs]
 [<ffffffffa0297434>] ? nfs_get_sb+0x435/0x73c [nfs]
 [<ffffffff810dd59b>] ? vfs_kern_mount+0x99/0x133
 [<ffffffff810dd693>] ? do_kern_mount+0x48/0xd8
 [<ffffffff810f5b75>] ? do_mount+0x6da/0x741
 [<ffffffff810f5c5f>] ? sys_mount+0x83/0xc0
 [<ffffffff8100293b>] ? system_call_fastpath+0x16/0x1b

Well, so, I think this is real bug of nfs codes somewhere. With some
review, the code

rpc_call_sync()
    rpc_run_task
        rpc_execute()
            __rpc_execute()
                rpc_release_task()
                    rpc_release_resources_task()
                        put_rpccred()                <= release cred
    rpc_put_task
        rpc_do_put_task()
            rpc_release_resources_task()
                put_rpccred()                        <= release cred again

seems to be release cred unintendedly.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

Now that the inode scalability patches have been merged, it is no longer
safe to call igrab() under the inode->i_lock.
Now that we no longer call nfs_clear_request() until the nfs_page is
being freed, we know that we are always holding a reference to the
nfs_open_context, which again holds a reference to the path, and so
the inode cannot be freed until the last nfs_page has been removed
from the radix tree and freed.

We can therefore skip the igrab()/iput() altogether.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

The device table is required to load modules based on modaliases.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: MyungJoo Ham <myungjoo.ham@smasung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Use the combined irq_set_chip_and_handler() function
instead. Converted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>