This patch enables the ibm_newemac driver for the Walnut board.  It fixes the
device tree for the walnut board to order the MAL interrupts correctly and
adds the local-mac-address property to the EMAC node.  The bootwrapper is also
updated to extract the MAC address from the OpenBIOS offset where it is stored.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

The current bootwrapper fails to set the timebase clock to the CPU clock
which causes the time to increment incorrectly.  This fixes it by using the
correct #define for the CPC0_CR1 register.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

Update the Ebony defconfig to enable the ibm_newemac driver.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

Currently there's no way to enable early boot console on PowerPC 44x
not specifying uart's physical address in kernel config, which is used
for very early debug messages. This patch splits very early debug output
(which needs uart physical address in kernel config) and early boot console
(which searches for uarts in the device tree using find_legacy_serial_ports).
We enable early boot console for all 44x processors, while (dangerous)
early debug is user-selectable.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

This patch enables NEW EMAC support for PowerPC 440EPx Sequoia board.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

This adds RGMII support to Sequoia DTS and sets correct phy-mode
for EMACs. According to Sequoia datasheet, both ethernet ports
are connected to RGMII interface, while ZMII is used only for MDIO.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
  pcnet32: remove private net_device_stats structure
  vortex_up should initialize "err"
  pcnet32: remove compile warnings in non-napi mode
  pcnet32: fix non-napi packet reception
  fix EMAC driver for proper napi_synchronize API
  sky2: shutdown cleanup
  napi_synchronize: waiting for NAPI
  forcedeth msi bugfix
  gianfar: fix obviously wrong #ifdef CONFIG_GFAR_NAPI placement
  fs_enet: Update for API changes
  gianfar: remove orphan struct.
  forcedeth: fix rx-work condition in nv_rx_process_optimized() too

* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6: (37 commits)
  ide: set drive->autotune in ide_pci_setup_ports()
  triflex: always tune PIO
  opti621: always tune PIO
  cy82c693: always tune PIO
  cs5520: always tune PIO
  alim15x3: always tune PIO
  ide: add IDE_HFLAG_LEGACY_IRQS host flag
  ide: add IDE_HFLAG_SERIALIZE host flag
  ide: add IDE_HFLAG_ERROR_STOPS_FIFO host flag
  piix: add DECLARE_ICH_DEV() macro
  pdc202xx_old: add DECLARE_PDC2026X_DEV() macro
  pdc202xx_new: add DECLARE_PDCNEW_DEV() macro
  aec62xx: no need to disable UDMA in ->init_hwif method for ATP850UF
  ide: remove .init_setup from ide_pci_device_t
  serverworks: remove ->init_setup
  scc_pata: remove ->init_setup
  pdc202xx_old: remove ->init_setup
  pdc202xx_new: remove ->init_setup
  hpt366: remove ->init_setup
  cmd64x: remove ->init_setup
  ...

Majority of host drivers using IDE PCI layer set drive->autotune, the only
exceptions are:

generic.c
ns87415.c
rz1000.c
trm290.c
* no ->set_pio_mode method

it821x.c:
* if memory allocation fails drive->autotune won't be set
  (but there also won't be ->set_pio_mode method in such case)

piix.c:
* MPIIX controller (no ->init_hwif method so also no ->set_pio_mode method)

However if there is no ->set_pio_mode method there are no changes in behavior
w.r.t. PIO tuning so always set drive->autotune in ide_pci_setup_ports().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Since cs5520 uses VDMA best PIO mode was tuned anyway by ide_dma_check()
but only if DMA was successfully initialized.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add IDE_HFLAG_LEGACY_IRQS host flag to tell ide_pci_setup_ports() to set
hwif->irq to legacy IRQ 14/15 (iff hwif->irq is not already set) and convert
atiixp, piix, serverworks, sis5513 and slc90e66 host drivers to use it.

While at it:

* In piix.c add IDE_HFLAGS_PIIX define and don't use ->init_hwif for MPIIX.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add IDE_HFLAG_SERIALIZE host flag to tell ide_pci_setup_ports() to set
hwif/mate->serialized and convert aec62xx, cs5530 and sc1200 host drivers
to use it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add IDE_HFLAG_ERROR_STOPS_FIFO host flag and use it instead
of hwif->err_stops_fifo.  As a side-effect this change fixes
hwif->err_stops_fifo not being restored by ide_hwif_restore().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add DECLARE_ICH_DEV() macro.

While at it:

* Add init_hwif_ich() (->init_hwif method) for ICH controllers.

* Rename init_chipset_piix() to init_chipset_ich() and use it only for
  ICH controllers.

* Remove no longer needed piix_is_ichx() helper.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* No need to disable UDMA in ->init_hwif method for ATP850UF (and since we
  now always tune PIO it will be disabled by ->set_pio_mode calls anyway).

* Bump driver version.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Now that all users were fixed we can safely remove it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Merge init_setup_{svwks,csb6}() into svwks_init_one().

While at it:

* Remove redundant dev->device checks.

* Operate on a local copy of serverworks_chipsets[] entry.

* Use pci_resource_start().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Split off pdc202ata4_fixup_irq() helper from init_setup_pdc202ata4().

* Merge init_setup_{pdc202ata4,pdc20265,pdc202xx}() into pdc202xx_init_one().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Split off pdc20270_get_dev2() helper from init_setup_pdc20270().

* Merge init_setup_{pdcnew,pdc20270,pdc20276}() into pdc202new_init_one().

While at it:

* Change KERN_ level of interrupt fixup message from KERN_WARNING to KERN_INFO.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Split off hpt{374,371,366}_init() helper from init_setup_hpt{374,371,366}().

* Merge init_setup_{374,372n,371,372a,302,366}() into hpt366_init_one().

While at it:

* Use "HPT36x" name for HPT366/HPT368 chipsets.

* Add .chip_name to struct hpt_info and use it to set set d->name.

* Convert .max_ultra in struct hpt_info to .udma_mask and use it to set
  d->udma_mask.

* Fix hpt302 to use HPT302_ALLOW_ATA133_6 define.

* Change HPT366/HPT374 interrupt fixup message from KERN_WARNING to KERN_INFO.

* Use the second hpt366_chipsets[] entry for HPT37x chipsets using HPT36x PCI
  device ID and fix .enablebits/.host_flags for HPT36x hpt366_chipsets[] entry.

* Bump driver version.

Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Merge init_setup_{cmd64x,cmd646}() into cmd64x_init_one().

Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Merge init_setup_{aec62xx,aec6x80}() into aec62xx_init_one().

While at it:

* Use id->driver_data instead of dev->device.

* Use ATA_UDMA6 define.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

v2:
- bump host driver versions (as suggested by Sergei)
- use I/O ops directly in drivers/ide/setup-pci.c

Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Some places were using PCI_CLASS_REVISION instead of PCI_REVISION_ID so
they were not converted by commit 44c10138.

Cc: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add ->mwdma_mask and ->swdma_mask to ide_pci_device_t.

* Set ide_hwif_t DMA masks using DMA masks from ide_pci_device_t in
  setup-pci.c::ide_pci_setup_ports() (iff DMA base is valid and ->init_hwif
  method may still override them).

* Convert IDE PCI host drivers to use ide_pci_device_t DMA masks.

While at it:

* Use ATA_{UDMA,MWDMA,SWDMA}* defines.

* hpt34x.c: add separate ide_pci_device_t instances for HPT343 and HPT345.

* serverworks.c: fix DMA masks being set before checking DMA base.

v2:
* Add missing masks to DECLARE_GENERIC_PCI_DEV() macro.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Documentation doesn't mention SWDMA and moreover all timings used
for SWDMA modes were over-clocked when compared to ATA spec.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add IDE_HFLAG_NO_LBA48[_DMA] host flags, use it instead of hwif->no_lba48[_dma]
and then remove no longer needed hwif->no_lba48[_dma].  As a side-effect
this change fixes hwif->no_lba48_dma not being restored by ide_hwif_restore().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Make ide_pci_device_t.host_flags u32 and add IDE_HFLAG_CS5520 host flag.

* Pass ide_pci_device_t *d to setup-pci.c::ide_get_or_set_dma_base()
  and use d->name instead of hwif->cds->name.

* Set IDE_HFLAG_CS5520 host flag in cs5520 host driver and use it in
  ide_get_or_set_dma_base() to find out which PCI BAR to use, remove no longer
  needed cs5520.c::cs5520_init_setup_dma() and ide_pci_device_t.init_setup_dma.

  This fixes PCI bus-mastering not being checked for CS5510/CS5520 hosts.

v2:
* It is wrong to check simplex bits on CS5510/CS5520 as v1 did.
  (Noticed by Alan).

Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add IDE_HFLAG_NO_{DMA,AUTODMA} host flags.  Convert all host drivers using
ide_pci_device_t to use these flags instead of d->autodma and then remove no
longer needed d->autodma.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add IDE_HFLAG_BOOTABLE host flag and IDE_HFLAG_OFF_BOARD define.  Convert
all host drivers using ide_pci_device_t to use IDE_HFLAG_{BOOTABLE,OFF_BOARD}
instead of d->bootable and then remove no longer needed d->bootable.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add IDE_HFLAG_NO_ATAPI_DMA host flag and set it in host drivers which
don't support ATAPI DMA.  Then remove no longer needed hwif->atapi_dma.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>