At the time padding_length() is called the record header
is still part of the message.  If malicious TLS 1.3 peer
sends an all-zero record padding_length() will stop at
the record header, and return full length of the data
including the tail_size.

Subsequent subtraction of prot->overhead_size from rxm->full_len
will cause rxm->full_len to turn negative.  skb accessors,
however, will always catch resulting out-of-bounds operation,
so in practice this fix comes down to returning the correct
error code.  It also fixes a set but not used warning.

This code was added by commit 130b392c ("net: tls: Add tls 1.3 support").

CC: Dave Watson <davejwatson@fb.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 4504ab0e ("net/tls: Inform user space about send buffer availability")
made us report write_space regardless whether partial record
push was successful or not.  Remove the now unused return value
to clean up the following W=1 warning:

net/tls/tls_device.c: In function ‘tls_device_write_space’:
net/tls/tls_device.c:546:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
  int rc = 0;
      ^~

CC: Vakul Garg <vakul.garg@nxp.com>
CC: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexei Starovoitov says:

====================
pull-request: bpf 2019-05-09

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) three small fixes from Gary, Jiong and Lorenz.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The section titles of 3.4 and 3.5 are not marked correctly.
Signed-off-by: Gary Lin <glin@suse.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

NFP shift instruction has something special. If shift direction is left
then shift amount of 1 to 31 is specified as 32 minus the amount to shift.

But no need to do this for indirect shift which has shift amount be 0. Even
after we do this subtraction, shift amount 0 will be turned into 32 which
will eventually be encoded the same as 0 because only low 5 bits are
encoded, but shift amount be 32 will fail the FIELD_PREP check done later
on shift mask (0x1f), due to 32 is out of mask range. Such error has been
observed when compiling nfp/bpf/jit.c using gcc 8.3 + O3.

This issue has started when indirect shift support added after which the
incoming shift amount to __emit_shf could be 0, therefore it is at that
time shift amount adjustment inside __emit_shf should have been tightened.

Fixes: 991f5b36 ("nfp: bpf: support logic indirect shifts (BPF_[L|R]SH | BPF_X)")
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Reported-by: Pablo Cascón <pablo.cascon@netronome.com
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

There are a few tests which call bpf_object__close on uninitialized
bpf_object*, which may segfault. Explicitly zero-initialise these pointers
to avoid this.
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

kernel BUG at lib/list_debug.c:47!
invalid opcode: 0000 [#1
CPU: 0 PID: 12914 Comm: rmmod Tainted: G        W         5.1.0+ #47
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.9.3-0-ge2fc41e-prebuilt.qemu-project.org 04/01/2014
RIP: 0010:__list_del_entry_valid+0x53/0x90
Code: 48 8b 32 48 39 fe 75 35 48 8b 50 08 48 39 f2 75 40 b8 01 00 00 00 5d c3 48
89 fe 48 89 c2 48 c7 c7 18 75 fe 82 e8 cb 34 78 ff <0f> 0b 48 89 fe 48 c7 c7 50 75 fe 82 e8 ba 34 78 ff 0f 0b 48 89 f2
RSP: 0018:ffffc90001c2fe40 EFLAGS: 00010286
RAX: 000000000000004e RBX: ffffffffa0184000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffff888237a17788 RDI: 00000000ffffffff
RBP: ffffc90001c2fe40 R08: 0000000000000000 R09: 0000000000000000
R10: ffffc90001c2fe10 R11: 0000000000000000 R12: 0000000000000000
R13: ffffc90001c2fe50 R14: ffffffffa0184000 R15: 0000000000000000
FS:  00007f3d83634540(0000) GS:ffff888237a00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000555c350ea818 CR3: 0000000231677000 CR4: 00000000000006f0
Call Trace:
 unregister_pernet_operations+0x34/0x120
 unregister_pernet_subsys+0x1c/0x30
 packet_exit+0x1c/0x369 [af_packet
 __x64_sys_delete_module+0x156/0x260
 ? lockdep_hardirqs_on+0x133/0x1b0
 ? do_syscall_64+0x12/0x1f0
 do_syscall_64+0x6e/0x1f0
 entry_SYSCALL_64_after_hwframe+0x49/0xbe

When modprobe af_packet, register_pernet_subsys
fails and does a cleanup, ops->list is set to LIST_POISON1,
but the module init is considered to success, then while rmmod it,
BUG() is triggered in __list_del_entry_valid which is called from
unregister_pernet_subsys. This patch fix error handing path in
packet_init to avoid possilbe issue if some error occur.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

User space can flip the clean_acked_data_enabled static branch
on and off with TLS offload when CONFIG_TLS_DEVICE is enabled.
jump_label.h suggests we use the delayed version in this case.

Deferred branches now also don't take the branch mutex on
decrement, so we avoid potential locking issues.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/aquantia/atlantic/aq_drvinfo.o: In function `aq_drvinfo_init':
aq_drvinfo.c:(.text+0xe8): undefined reference to `devm_hwmon_device_register_with_info'

Fix it by using #if IS_REACHABLE(CONFIG_HWMON).
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simon Wunderlich says:

====================
This feature/cleanup patchset includes the following patches:

 - bump version strings, by Simon Wunderlich (we forgot to include
   this patch previously ...)

 - fix multicast tt/tvlv worker locking, by Linus Lüssing
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If you are using a function that does a swap in place,
you cannot just reuse the buffer on the assumption that it has
not been changed.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When writing to the phy on BE architectures an internal data structure
was directly given, leading to it being byte swapped in the wrong
way for the CPU in 50% of all cases. A temporary buffer must be used.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the MTU is large enough, the first write to the device
is just repeated. On BE architectures, however, the first
word of the command will be swapped a second time and garbage
will be written. Avoid that.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With NET_ADMIN enabled in container, a normal user could be mapped to
root and is able to change the real device's rx filter via ioctl on
vlan, which would affect the other ptp process on host. Fix it by
disabling SIOCSHWTSTAMP in container.

Fixes: a6111d3c ("vlan: Pass SIOC[SG]HWTSTAMP ioctls to real device")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Miroslav pointed that with NET_ADMIN enabled in container, a normal user
could be mapped to root and is able to change the real device's rx
filter via ioctl on macvlan, which would affect the other ptp process on
host. Fix it by disabling SIOCSHWTSTAMP in container.

Fixes: 254c0a2b ("macvlan: pass get_ts_info and SIOC[SG]HWTSTAMP ioctl to real device")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 517d7c79 ("tipc: fix hanging poll() for stream sockets")
introduced a regression for clients using non-blocking sockets.
After the commit, we send EPOLLOUT event to the client even in
TIPC_CONNECTING state. This causes the subsequent send() to fail
with ENOTCONN, as the socket is still not in TIPC_ESTABLISHED state.

In this commit, we:
- improve the fix for hanging poll() by replacing sk_data_ready()
  with sk_state_change() to wake up all clients.
- revert the faulty updates introduced by commit 517d7c79
  ("tipc: fix hanging poll() for stream sockets").

Fixes: 517d7c79 ("tipc: fix hanging poll() for stream sockets")
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@gmail.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a queue(tfile) is detached through __tun_detach(), we move the
last enabled tfile to the position where detached one sit but don't
NULL out last position. We expect to synchronize the datapath through
tun->numqueues. Unfortunately, this won't work since we're lacking
sufficient mechanism to order or synchronize the access to
tun->numqueues.

To fix this, NULL out the last position during detaching and check
RCU protected tfile against NULL instead of checking tun->numqueues in
datapath.

Cc: YueHaibing <yuehaibing@huawei.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: weiyongjun (A) <weiyongjun1@huawei.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Fixes: c8d68e6b ("tuntap: multiqueue support")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need check if tun->numqueues is zero (e.g for the persist device)
before trying to use it for modular arithmetic.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Fixes: 96f84061("tun: add eBPF based queue selection method")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: stmmac: dwmac4_prog_mtl_tx_algorithms() missing write operation

The value of MTL_OPERATION_MODE is not written back
Signed-off-by: Cheng Han <hancheng2009@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure ptp dt node exists before accessing it in case
of NULL pointer call trace.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Avoid freeing cls_mall.rule twice when failing to setup flow_action
offload used in the hardware intermediate representation. This is
achieved by returning 0 when the setup fails but the skip software
flag has not been set.

Fixes: f00cbf19 ("net/sched: use the hardware intermediate representation for matchall")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NFP does not register devlink ports for representors (without
the "devlink: expose PF and VF representors as ports" series
there are no port flavours to expose them as).

Commit c25f08ac ("nfp: remove ndo_get_port_parent_id implementation")
went to far in removing ndo_get_port_parent_id for representors.
This causes redirection offloads to fail, and switch_id attribute
missing.

Reintroduce the ndo_get_port_parent_id callback for representor ports.

Fixes: c25f08ac ("nfp: remove ndo_get_port_parent_id implementation")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Serge Semin says:

====================
net: phy: realtek: Fix RGMII TX/RX-delays initial config of rtl8211(e|f)

It has been discovered that RX/TX delays of rtl8211e ethernet PHY
can be configured via a MDIO register hidden in the extension pages
layout. Particularly the extension page 0xa4 provides a register 0x1c,
which bits 1 and 2 control the described delays. They are used to
implement the "rgmii-{id,rxid,txid}" phy-mode support in patch 1.

The second patch makes sure the rtl8211f TX-delay is configured only
if RGMII interface mode is specified including the rgmii-rxid one.
In other cases (most importantly for NA mode) the delays are supposed
to be preconfigured by some other software or hardware and should be
left as is without any modification. The similar thing is also done
for rtl8211e in the patch 1 of this series.

Changelog v3
- Add this cover-letter.
- Add Andrew' Reviewed-by tag to patch 1.
- Accept RGMII_RXID interface mode for rtl8211f and clear the TX_DELAY
  bit in this case.
- Initialize ret variable with 0 to prevent the "may be used uninitialized"
  warning in patch 1.

Changelog v4
- Rebase onto net-next
====================
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It's prone to problems if delay is cleared out for other than RGMII
modes. So lets set/clear the TX-delay in the config register only
if actually RGMII-like interface mode is requested. This only
concerns rtl8211f chips.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are two chip pins named TXDLY and RXDLY which actually adds the 2ns
delays to TXC and RXC for TXD/RXD latching. Alas this is the only
documented info regarding the RGMII timing control configurations the PHY
provides. It turns out the same settings can be setup via MDIO registers
hidden in the extension pages layout. Particularly the extension page 0xa4
provides a register 0x1c, which bits 1 and 2 control the described delays.
They are used to implement the "rgmii-{id,rxid,txid}" phy-mode.

The hidden RGMII configs register utilization was found in the rtl8211e
U-boot driver:
https://elixir.bootlin.com/u-boot/v2019.01/source/drivers/net/phy/realtek.c#L99

There is also a freebsd-folks discussion regarding this register:
https://reviews.freebsd.org/D13591

It confirms that the register bits field must control the so called
configuration pins described in the table 12-13 of the official PHY
datasheet:
8:6 = PHY Address
5:4 = Auto-Negotiation
3 = Interface Mode Select
2 = RX Delay
1 = TX Delay
0 = SELRGV
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dan Carpenter says:

The patch 640f763f: "net: dsa: sja1105: Add support for Spanning
Tree Protocol" from May 5, 2019, leads to the following static
checker warning:

        drivers/net/dsa/sja1105/sja1105_main.c:1073 sja1105_stp_state_get()
        warn: signedness bug returning '(-22)'

The caller doesn't check for negative errors anyway.

Fixes: 640f763f: ("net: dsa: sja1105: Add support for Spanning Tree Protocol")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The while-loop exit condition check is not correct; the
loop should continue if the returns from the function calls are
negative or the CRC status returns are invalid.  Currently it
is ignoring the returns from the function calls.  Fix this by
removing the status return checks and only break from the loop
at the very end when we know that all the success condtions have
been met.

Kudos to Dan Carpenter for describing the correct fix and
Vladimir Oltean for noting the change to the check on the number
of retries.

Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: 8aa9ebcc ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/dsa/sja1105/sja1105_spi.c:486:21: warning: symbol 'sja1105et_regs' was not declared. Should it be static?
drivers/net/dsa/sja1105/sja1105_spi.c:511:21: warning: symbol 'sja1105pqrs_regs' was not declared. Should it be static?

Fixes: 8aa9ebcc ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai26@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

calling connect(AF_UNSPEC) on an already connected TCP socket is an
established way to disconnect() such socket. After commit 68741a8a
("selinux: Fix ltp test connect-syscall failure") it no longer works
and, in the above scenario connect() fails with EAFNOSUPPORT.

Fix the above falling back to the generic/old code when the address family
is not AF_INET{4,6}, but leave the SCTP code path untouched, as it has
specific constraints.

Fixes: 68741a8a ("selinux: Fix ltp test connect-syscall failure")
Reported-by: Tom Deseyn <tdeseyn@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The pointer l2_hdr is being assigned to itself, this is redundant
and can be removed.

Addresses-Coverity: ("Evaluation order violation")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are several spelling mistakes in dev_err messages. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 4806e975 ("netfilter: replace NF_NAT_NEEDED with
IS_ENABLED(CONFIG_NF_NAT)") removed CONFIG_NF_NAT_NEEDED, but a new user
popped up afterwards.

Fixes: fec9c271 ("openvswitch: load and reference the NAT helper.")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Florian Westphal <fw@strlen.de>
Acked-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

inet_iif should be used for the raw socket lookup. inet_iif considers
rt_iif which handles the case of local traffic.

As it stands, ping to a local address with the '-I <dev>' option fails
ever since ping was changed to use SO_BINDTODEVICE instead of
cmsg + IP_PKTINFO.

IPv6 works fine.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With commit 153380ec ("fib_rules: Added NLM_F_EXCL support to
fib_nl_newrule") we now able to check if a rule already exists. But this
only works with iproute2. For other tools like libnl, NetworkManager,
it still could add duplicate rules with only NLM_F_CREATE flag, like

[localhost ~ ]# ip rule
0:      from all lookup local
32766:  from all lookup main
32767:  from all lookup default
100000: from 192.168.7.5 lookup 5
100000: from 192.168.7.5 lookup 5

As it doesn't make sense to create two duplicate rules, let's just return
0 if the rule exists.

Fixes: 153380ec ("fib_rules: Added NLM_F_EXCL support to fib_nl_newrule")
Reported-by: Thomas Haller <thaller@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking updates from David Miller:
 "Highlights:

   1) Support AES128-CCM ciphers in kTLS, from Vakul Garg.

   2) Add fib_sync_mem to control the amount of dirty memory we allow to
      queue up between synchronize RCU calls, from David Ahern.

   3) Make flow classifier more lockless, from Vlad Buslov.

   4) Add PHY downshift support to aquantia driver, from Heiner
      Kallweit.

   5) Add SKB cache for TCP rx and tx, from Eric Dumazet. This reduces
      contention on SLAB spinlocks in heavy RPC workloads.

   6) Partial GSO offload support in XFRM, from Boris Pismenny.

   7) Add fast link down support to ethtool, from Heiner Kallweit.

   8) Use siphash for IP ID generator, from Eric Dumazet.

   9) Pull nexthops even further out from ipv4/ipv6 routes and FIB
      entries, from David Ahern.

  10) Move skb->xmit_more into a per-cpu variable, from Florian
      Westphal.

  11) Improve eBPF verifier speed and increase maximum program size,
      from Alexei Starovoitov.

  12) Eliminate per-bucket spinlocks in rhashtable, and instead use bit
      spinlocks. From Neil Brown.

  13) Allow tunneling with GUE encap in ipvs, from Jacky Hu.

  14) Improve link partner cap detection in generic PHY code, from
      Heiner Kallweit.

  15) Add layer 2 encap support to bpf_skb_adjust_room(), from Alan
      Maguire.

  16) Remove SKB list implementation assumptions in SCTP, your's truly.

  17) Various cleanups, optimizations, and simplifications in r8169
      driver. From Heiner Kallweit.

  18) Add memory accounting on TX and RX path of SCTP, from Xin Long.

  19) Switch PHY drivers over to use dynamic featue detection, from
      Heiner Kallweit.

  20) Support flow steering without masking in dpaa2-eth, from Ioana
      Ciocoi.

  21) Implement ndo_get_devlink_port in netdevsim driver, from Jiri
      Pirko.

  22) Increase the strict parsing of current and future netlink
      attributes, also export such policies to userspace. From Johannes
      Berg.

  23) Allow DSA tag drivers to be modular, from Andrew Lunn.

  24) Remove legacy DSA probing support, also from Andrew Lunn.

  25) Allow ll_temac driver to be used on non-x86 platforms, from Esben
      Haabendal.

  26) Add a generic tracepoint for TX queue timeouts to ease debugging,
      from Cong Wang.

  27) More indirect call optimizations, from Paolo Abeni"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1763 commits)
  cxgb4: Fix error path in cxgb4_init_module
  net: phy: improve pause mode reporting in phy_print_status
  dt-bindings: net: Fix a typo in the phy-mode list for ethernet bindings
  net: macb: Change interrupt and napi enable order in open
  net: ll_temac: Improve error message on error IRQ
  net/sched: remove block pointer from common offload structure
  net: ethernet: support of_get_mac_address new ERR_PTR error
  net: usb: smsc: fix warning reported by kbuild test robot
  staging: octeon-ethernet: Fix of_get_mac_address ERR_PTR check
  net: dsa: support of_get_mac_address new ERR_PTR error
  net: dsa: sja1105: Fix status initialization in sja1105_get_ethtool_stats
  vrf: sit mtu should not be updated when vrf netdev is the link
  net: dsa: Fix error cleanup path in dsa_init_module
  l2tp: Fix possible NULL pointer dereference
  taprio: add null check on sched_nest to avoid potential null pointer dereference
  net: mvpp2: cls: fix less than zero check on a u32 variable
  net_sched: sch_fq: handle non connected flows
  net_sched: sch_fq: do not assume EDT packets are ordered
  net: hns3: use devm_kcalloc when allocating desc_cb
  net: hns3: some cleanup for struct hns3_enet_ring
  ...

Pull Devicetree updates from Rob Herring:

 - Fix possible memory leak in reserved-memory failure case

 - Support for DMA parent bus which are not a parent node

 - Clang -Wunsequenced fix

 - Remove some unnecessary prints on memory alloc failures

 - Various printk msg and comment fixes

 - Update DT schema tools repository location

 - Convert simple-framebuffer binding to DT schema

 - Bindings for isl68137 and ir38064 trivial devices

 - New documentation on binding do's and don't's for binding writers to
   ignore

* tag 'devicetree-for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (22 commits)
  of: unittest: Remove error printing on OOM
  of: irq: Remove WARN_ON() for kzalloc() failure
  dt-bindings: pinctrl: fix bias-pull,up typo
  dt-bindings: Update schema project location to devicetree.org github group
  of: fix clang -Wunsequenced for be32_to_cpu()
  of/device.c: fix the wrong comments
  dt-bindings: Add isl68137 as a trivial device
  dt-bindings: Add ir38064 as a trivial device
  of: del redundant type conversion
  dt-bindings: mfd: axp20x: Add fallback for axp805
  of: Improve of_phandle_iterator_next() error message
  dt-bindings: connector: Spelling mistake
  dt-bindings: Add schemas for simple-framebuffer
  of: address: Add support for the parent DMA bus
  of: address: Retrieve a parent through a callback in __of_translate_address
  dt-bindings: bus: Add binding for the Allwinner MBUS controller
  dt-bindings: interconnect: Add a dma interconnect name
  of: use correct function prototype for of_overlay_fdt_apply()
  of: reserved_mem: fix reserve memory leak
  of: property: Document that of_graph_get_endpoint_by_regs needs of_node_put
  ...

Pull randomness updates from Ted Ts'o:

 - initialize the random driver earler

 - fix CRNG initialization when we trust the CPU's RNG on NUMA systems

 - other miscellaneous cleanups and fixes.

* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
  random: add a spinlock_t to struct batched_entropy
  random: document get_random_int() family
  random: fix CRNG initialization when random.trust_cpu=1
  random: move rand_initialize() earlier
  random: only read from /dev/random after its pool has received 128 bits
  drivers/char/random.c: make primary_crng static
  drivers/char/random.c: remove unused stuct poolinfo::poolbits
  drivers/char/random.c: constify poolinfo_table

Pull fscrypt updates from Ted Ts'o:
 "Clean up fscrypt's dcache revalidation support, and other
  miscellaneous cleanups"

* tag 'fscrypt_for_linus' of git://git.kernel.org/pub/scm/fs/fscrypt/fscrypt:
  fscrypt: cache decrypted symlink target in ->i_link
  vfs: use READ_ONCE() to access ->i_link
  fscrypt: fix race where ->lookup() marks plaintext dentry as ciphertext
  fscrypt: only set dentry_operations on ciphertext dentries
  fs, fscrypt: clear DCACHE_ENCRYPTED_NAME when unaliasing directory
  fscrypt: fix race allowing rename() and link() of ciphertext dentries
  fscrypt: clean up and improve dentry revalidation
  fscrypt: use READ_ONCE() to access ->i_crypt_info
  fscrypt: remove WARN_ON_ONCE() when decryption fails
  fscrypt: drop inode argument from fscrypt_get_ctx()

Pull ext4 updates from Ted Ts'o:
 "Add as a feature case-insensitive directories (the casefold feature)
  using Unicode 12.1.

  Also, the usual largish number of cleanups and bug fixes"

* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (25 commits)
  ext4: export /sys/fs/ext4/feature/casefold if Unicode support is present
  ext4: fix ext4_show_options for file systems w/o journal
  unicode: refactor the rule for regenerating utf8data.h
  docs: ext4.rst: document case-insensitive directories
  ext4: Support case-insensitive file name lookups
  ext4: include charset encoding information in the superblock
  MAINTAINERS: add Unicode subsystem entry
  unicode: update unicode database unicode version 12.1.0
  unicode: introduce test module for normalized utf8 implementation
  unicode: implement higher level API for string handling
  unicode: reduce the size of utf8data[]
  unicode: introduce code for UTF-8 normalization
  unicode: introduce UTF-8 character database
  ext4: actually request zeroing of inode table after grow
  ext4: cond_resched in work-heavy group loops
  ext4: fix use-after-free race with debug_want_extra_isize
  ext4: avoid drop reference to iloc.bh twice
  ext4: ignore e_value_offs for xattrs with value-in-ea-inode
  ext4: protect journal inode's blocks using block_validity
  ext4: use BUG() instead of BUG_ON(1)
  ...

Pull AFS updates from David Howells:
 "A set of fix and development patches for AFS for 5.2.

  Summary:

   - Fix the AFS file locking so that sqlite can run on an AFS mount and
     also so that firefox and gnome can use a homedir that's mounted
     through AFS.

     This required emulation of fine-grained locking when the server
     will only support whole-file locks and no upgrade/downgrade. Four
     modes are provided, settable by mount parameter:

       "flock=local"   - No reference to the server

       "flock=openafs" - Fine-grained locks are local-only, whole-file
                         locks require sufficient server locks

       "flock=strict"  - All locks require sufficient server locks

       "flock=write"   - Always get an exclusive server lock

     If the volume is a read-only or backup volume, then flock=local for
     that volume.

   - Log extra information for a couple of cases where the client mucks
     up somehow: AFS vnode with undefined type and dir check failure -
     in both cases we seem to end up with unfilled data, but the issues
     happen infrequently and are difficult to reproduce at will.

   - Implement silly rename for unlink() and rename().

   - Set i_blocks so that du can get some information about usage.

   - Fix xattr handlers to return the right amount of data and to not
     overflow buffers.

   - Implement getting/setting raw AFS and YFS ACLs as xattrs"

* tag 'afs-next-20190507' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
  afs: Implement YFS ACL setting
  afs: Get YFS ACLs and information through xattrs
  afs: implement acl setting
  afs: Get an AFS3 ACL as an xattr
  afs: Fix getting the afs.fid xattr
  afs: Fix the afs.cell and afs.volume xattr handlers
  afs: Calculate i_blocks based on file size
  afs: Log more information for "kAFS: AFS vnode with undefined type\n"
  afs: Provide mount-time configurable byte-range file locking emulation
  afs: Add more tracepoints
  afs: Implement sillyrename for unlink and rename
  afs: Add directory reload tracepoint
  afs: Handle lock rpc ops failing on a file that got deleted
  afs: Improve dir check failure reports
  afs: Add file locking tracepoints
  afs: Further fix file locking
  afs: Fix AFS file locking to allow fine grained locks
  afs: Calculate lock extend timer from set/extend reply reception
  afs: Split wait from afs_make_call()