Remove a little bit of unnecessary work when transmitting a packet with
neigh_packet_xmit.  Use the neighbour table index not the address family
as a parameter.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the OPENVSWITCH Kconfig option and old Kconfigs by having
OPENVSWITCH select both NET_MPLS_GSO and MPLSO.

A Kbuild test robot reported that when NET_MPLS_GSO is selected by
OPENVSWITCH the generated .config is broken because MPLS is not
selected.

Cc: Simon Horman <horms@verge.net.au>
Fixes: cec9166c mpls: Refactor how the mpls module is built
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

According to RFC3032 section 2.4.2  packets with an outgoing
ttl of 0 MUST NOT be forwarded.  According to section 2.4.1
an outgoing TTL of 0 comes from an incomming TTL <= 1.

Therefore any packets that is received with a ttl <= 1 should
not have it's ttl decremented and forwarded.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sparse was generating a lot of warnings mostly from missing annotations
in the code.  Add missing annotations and in a few cases tweak the code
for performance by moving work before loops.

This also fixes a problematic ommision of rcu_assign_pointer and
rcu_dereference.

Hopefully with complete rcu annotations any new rcu errors will stick
out like a sore thumb.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

*Blink* I got the argument order wrong to kzalloc and the
code was working properly when tested. *Blink*

Fix that.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove reference to obsolete ifconfig command.
MTU can be changed with ip command instead.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2015-03-07

This series contains updates to i40e and i40evf only.

Most notably, Greg provides the patch to remove the dreaded configfs
changes in the driver.

Shannon cleans up a sparse warning by simply straighting out the code
so it is less convoluted.  Fixes an issue where the vector allocation
was trying too hard to save vectors for VMDq, to the point of not giving
the PF enough when in a tight situation, such as an NPAR partition.
Changed the driver to make sure that the PF will get all the queues and
vectors it wants to fill out its destiny.  Cleans up reporting to only
print the port and VEB stats if it is the first partition of a
multiplexed port.

Catherine cleans up some duplicated code by simply removing the duplicate
code.

Kamil cleans up the driver by removing an un-needed endian conversion
because it is already done by a register read function.

Jesse fixes a variable width of a datatype, where a u16 should have been
a u32.  Also cleans up debug_read_register() to resolve some sparse
warnings.  Updates the driver to use prefetch() to get the next Tx
descriptor, like in ixgbe, to improve performance.

Akeem moves around code to enable/disable loopback so that other non-SRIOV
supported driver functions can take advantage of the changes.

Anjali cleans up the logging for adding/deleting FD-SB filters, since
ethtool shows all the filters on an interface.  Updates the driver to
use l4_tunnel type generically to keep code flow simple.  Simplifies
the RSS code since the driver initializes the rss_size_max in sw_init.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable EEE support for MV88E6352.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

EEE configuration is similar for the various MV88E6xxx chips.
Add generic support for it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for supporting multiple Rx queues:
1. Move the initialization of priv->num_rx_bds, priv->rx_bds, and
   priv->rx_cbs from bcmgenet_init_rx_ring() to bcmgenet_init_dma()
   since they are not specific to a single Rx queue. Mimics the Tx
   init model where priv->num_tx_bds, priv->tx_bds, and priv->tx_cbs
   are initialized in bcmgenet_init_dma().
2. Program DMA_MBUF_DONE_THRESH = 1 so that future Rx queues Q0-Q15
   will get per-packet Rx interrupt.
3. Group DMA_START_ADDR, RDMA_READ_PTR, RDMA_WRITE_PTR, and DMA_END_ADDR
   initialization together. Mimics the Tx init model.
4. There is 1-to-1 mapping between RxCBs and RxBDs.
   Precalculate RxCB->bd_addr so that it can be used in the future.
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'macb-next'

Boris Brezillon says:

====================
net/macb: merge at91_ether driver into macb driver

The rm9200 boards use the dedicated at91_ether driver instead of the
regular macb driver.

Both the macb and at91_ether drivers can be compiled as separated
modules.
Since the at91_ether driver uses code from the macb driver, at91_ether.ko
depends on macb.ko.

However the macb.ko module always fails to load on rm9200 boards: the
macb_probe() function expects a hclk clock which doesn't exist on rm9200.
Then the at91_ether.ko can't be loaded in turn due to unresolved
dependencies.

This series of patches fix this issue by merging at91_ether into macb.

Patch 1 is fixing a problem that might happen when enabling ARM
multi-platform suppot.

Changes since v3:
- move "net: macb: remove #if defined(CONFIG_ARCH_AT91) sections" patch
  into this series to avoid dependency on other patch series.

Changes since v2:
- rebase after changed brought by commit "net: macb: remove #if
  defined(CONFIG_ARCH_AT91) sections"

Changes since v1:
- rework probe functions to share common probing logic
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

macb and at91_ether drivers can be compiled as modules, but the at91_ether
driver use some functions and variables defined in the macb one, thus
creating a dependency on the macb driver.

Since these drivers are sharing the same logic we can easily merge
at91_ether into macb.

In order to factorize common probing logic we've added an ->init() function
to struct macb_config (the structure associated with the compatible
string), and moved macb specific init code from macb_probe to macb_init.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Most of the functions from the Common Clk Framework handle NULL pointer as
input argument.

Since the TX clock is optional, we now set tx_clk to NULL value
instead of ERR_PTR(-ENOENT) when this clock is not available. This simplifies
the clock management and avoid the need to test tx_clk value.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With multi platform support those sections could lead to unexpected
behavior if both ARCH_AT91 and another ARM SoC using the MACB IP are
selected.
Add two new capabilities to encode the default MII mode and the presence
of a CLKEN bit in USRIO register.
Then define the appropriate config for IPs embedded in at91 SoCs.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some at91 SoCs embed a 10/100 Mbit Ethernet IP, that is based on the
at91sam9260 SoC.
Fix at91 DTs accordingly.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The use of configfs is not allowed in network drivers.  Strip the code that
uses it.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Bump i40e to 1.2.12 and i40evf to 1.2.6.

Change-ID: I641871da3a9abd396b28eda5744a4d68493c1400
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Performance can be improved a bit by imitating ixgbe and using
prefetch to get us the next Tx descriptor.

Change-ID: Ice7ffd4cd0ce87c35295059bdb7972a7f53723aa
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

We initialize the pf->rss_size_max in sw_init now
and hence this code can be simplified.

Change-ID: I1a7abc837604a40bc65e6c6b21190b909ed6bb21
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Use l4_tunnel type generically to keep code flow simple.

Change-ID: Ic52287e3b1ca4204e6b6e13431890c1a6ae9c422
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Since GLQF_FDCNT_0 register now has the right offset, use it to simplify our
FD flush flow.
If the filter add error happens to be for SB we just auto disable SB.

If filter error happens to be for ATR, auto disable ATR and mark
the state to FD_FLUSH_REQUESTED. Which gets cleared when flush completes.

If we are entering flush too quickly (< 30 seconds) and we have quite
a few SB rules, its time to disable ATR for good. Since SB + ATR rules
is most likely making the FD table unstable.

ATR can be re-enabled by turning ntuple off (ethtool -K ntuple off)
and will remain off after turning ntuple on till it gets unstable again.

Change-ID: I2154a2e0a5d44851a2f0eb8731e2f1d4a4d1acbc
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

It is not necessary to print FD filter add/delete log with
normal debug settings because ethtool -n ethx shows all the FD-SB
filters on an interface. The log can still be turned on through higher
debug levels and it will continue to print a log if there was an error
in the add/delete process.

Change-ID: I67db2baf49e2075d2f537de40f7895e5b02cd610
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Only print the port and veb stats if this is the first partition
of a multiplexed port.

Change-ID: I7ce0c323cdee5cfd2e54d8bea5b0b9102987e671
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Since changes made to enable or disable loopback for all VSIs, not only SR-IOV
or PCIOV, then it became necessary to move the associated functions to main
file - so that other non-SRIOV supported driver can take advantage of the
changes.

Change-ID: I59a49fd23a6136acda5e16f8d1e5ac7fd9c5fc05
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The initial problem solved here is that the vector allocation was trying
too hard to save vectors for VMDq, to the point of not giving the PF enough
when in a tight situation such as an NPAR partition.  This change makes
sure that the PF will get all the queues and vectors it wants to fill
out its destiny.  Essentially, nothing is specially reserved for VMDq,
it simply gets whatever is left after the PF, FCoE, and FD sideband get
what they want.

Additionally, the calculations for the reservations were harder to follow
than necessary, so I've made it more straight forward.

Change-ID: I99b384f104535b686c690b8ef0a787559485c8d4
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

There were some additional spaces and strange (double swapping) logic
in this function that I started looking at because sparse was warning.

This fixes the sparse warning and fixes up the other issues.

Change-ID: I72a91a4197cd45921602649040e6bd25e5f17c0a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The kernel returns a u32 for netif_msg_init, and we were storing
it in a u16.  Fix the width of the datatype.

Change-ID: I4b23326e5707c91cd59325c5a1ccb2ba7a3974fc
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove LE16 to CPU endianes conversion from i40e_read_nvm_word_srctl
function, as it's already done by register read function.

Change-ID: I739f0f20a9b8e18223e54c0ca5443e63d75da878
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This series of code was repeated twice, remove one of them.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

A sparse complaint in i40e_debug_aq in a funky buffer write goes away by
straightening out the code out to something less convoluted.

Also fix some other sparse warnings while we are at it, making some
functions static and using NULL instead of 0.

Change-ID: I93907534fe1f1f675830774b3d14ecf1c6ffc9a0
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Reviewed-by: Jonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fengguang reported, that on openrisc and avr32 architectures, we
get the following linker errors on *_defconfig builds that have
no bpf syscall support:

  net/built-in.o:(.rodata+0x1cd0): undefined reference to `bpf_map_lookup_elem_proto'
  net/built-in.o:(.rodata+0x1cd4): undefined reference to `bpf_map_update_elem_proto'
  net/built-in.o:(.rodata+0x1cd8): undefined reference to `bpf_map_delete_elem_proto'

Fix it up by providing built-in weak definitions of the symbols,
so they can be overridden when the syscall is enabled. I think
the issue might be that gcc is not able to optimize all that away.
This patch fixes the linker errors for me, tested with Fengguang's
make.cross [1] script.

  [1] https://git.kernel.org/cgit/linux/kernel/git/wfg/lkp-tests.git/plain/sbin/make.crossReported-by: Fengguang Wu <fengguang.wu@intel.com>
Fixes: d4052c4a ("ebpf: remove CONFIG_BPF_SYSCALL ifdefs in socket filter code")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some drivers use copybreak to copy tiny frames into smaller skb,
and this smaller skb might not have skb->head_frag set for various
reasons.

skb_gro_receive() currently doesn't allow to aggregate the smaller skb
into the previous GRO packet if this GRO packet has at least 2 MSS in
it.

Following workload easily demonstrates the problem.

netperf -t TCP_RR -H target -- -r 3000,3000

(tcpdump shows one GRO packet with 2 MSS, plus one additional packet of
104 bytes that should have been appended.)

It turns out that we can remove code from skb_gro_receive(), because
commit 8a29111c ("net: gro: allow to build full sized skb") and its
followups removed the assumption that a GRO packet with a frag_list had
to have an empty head.

Removing this code allows the aggregation of the last (incomplete) frame
in some RPC workloads. Note that tcp_gro_receive() already takes care of
forcing a flush if necessary, including this case.

If we want to avoid using frag_list in the first place (in forwarding
workloads for example, as the outgoing NIC is generally not able to cope
with skbs having a frag_list), we need to address this separately.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

We get a static checker warning here on devel kernels:

	drivers/net/hamradio/mkiss.c:560 ax_xmit()
	warn: variable dereferenced before check 'skb' (see line 532)

It turns out that the NULL check can be deleted.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Or Gerlitz says:

====================
Add QCN support to the DCB NL layer

This series from Shani Michaeli adds support for the IEEE QCN attribute
to the kernel DCB NL stack, and implementation in the mlx4 driver which
programs the firmware according to the admin directives.

changes from V0:

 - applied feedback from John and added his acked-by to patch #1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement the IEEE DCB handlers for set/get QCN parameters and
statistics reading per TC.
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add device capability, firmware command opcode and etc prior elements
needed for QCN suppprt. Disable SRIOV VF view/access for QCN is disabled.

While here, remove a redundant offset definition into the
QUERY_DEV_CAP mailbox.
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As specified in 802.1Qau spec. Add this optional attribute to the
DCB netlink layer. To allow for application to use the new attribute,
NIC drivers should implement and register the  callbacks ieee_getqcn,
ieee_setqcn and ieee_getqcnstats.

The QCN attribute holds a set of parameters for management, and
a set of statistics to provide informative data on Congestion-Control
defined by this spec.
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>