There is no need to determine the HW queue
for each packet that is transmitted. The endpoint
can be chosen directly based on the queue type
that mac80211 sends down.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch initializes the beacon and CAB HW queues
when the driver is loaded.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch enables short GI rx at all rates and tx at mcs15
for 20 Mhz channel width also.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use kzalloc rather than the combination of kmalloc and memset.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression x,size,flags;
statement S;
@@

-x = kmalloc(size,flags);
+x = kzalloc(size,flags);
 if (x == NULL) S
-memset(x, 0, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This enables the baseband watchdog events for the AR9003
family on ath9k. Upon an a baseband watchdog interrupt we reset
the hardware, this should address corner case conditions where
normal operation can stall. Enable ATH_DBG_RESET to be able
to review details of the bb watchdog interrupt once it happens.
If you're curious how often this happens just grep the debugfs
interrupt file.

Cc: Sam Ng <sam.ng@atheros.com>
Cc: Paul Shaw <paul.shaw@atheros.com>
Cc: Don Breslin <don.breslin@atheros.com>
Cc: Cliff Holden <cliff.holden@atheros.com
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The baseband watchdog will monitor blocks of the baseband
through timers and will issue an interrupt when things are
detected to be stalled. It is only available on the AR9003
family.

Cc: Sam Ng <sam.ng@atheros.com>
Cc: Paul Shaw <paul.shaw@atheros.com>
Cc: Don Breslin <don.breslin@atheros.com>
Cc: Cliff Holden <cliff.holden@atheros.com
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This allows rt2x00debug_dump_frame to be used from everywhere.

This is preparation for beacon writing clean ups.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Make it possible to use wl1271's SDIO interface on non-ARM platforms.

Fully tested on a x86 platform, compile-tested on ARM.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The checksums of the initvals are:

initvals -f ar9003-2p2
0x00000000c2bfa7d5        ar9300_2p2_radio_postamble
0x00000000ada2b114        ar9300Modes_lowest_ob_db_tx_gain_table_2p2
0x00000000e0bc2c84        ar9300Modes_fast_clock_2p2
0x00000000056eaf74        ar9300_2p2_radio_core
0x0000000000000000        ar9300Common_rx_gain_table_merlin_2p2
0x0000000078658fb5        ar9300_2p2_mac_postamble
0x0000000023235333        ar9300_2p2_soc_postamble
0x0000000054d41904        ar9200_merlin_2p2_radio_core
0x000000008475a084        ar9300_2p2_baseband_postamble
0x000000009aaafd90        ar9300_2p2_baseband_core
0x000000003df9a326        ar9300Modes_high_power_tx_gain_table_2p2
0x000000001cfba124        ar9300Modes_high_ob_db_tx_gain_table_2p2
0x0000000011302700        ar9300Common_rx_gain_table_2p2
0x00000000a9a2b114        ar9300Modes_low_ob_db_tx_gain_table_2p2
0x00000000a9d66d40        ar9300_2p2_mac_core
0x000000001e1d0800        ar9300Common_wo_xlna_rx_gain_table_2p2
0x00000000a0c531c8        ar9300_2p2_soc_preamble
0x00000000292e2544        ar9300PciePhy_pll_on_clkreq_disable_L1_2p2
0x000000002d3e2544        ar9300PciePhy_clkreq_enable_L1_2p2
0x00000000293e2544        ar9300PciePhy_clkreq_disable_L1_2p2
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The DMA API is preferred.

No functional change.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'wireless-next-2.6' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-2.6

Ethernet driver b44 does register ssb by it's pcihost_wrapper
and doesn't set ssb_chipcommon. A check on this value
introduced with commit d53cdbb9
and ea2db495 triggers:

BUG: unable to handle kernel NULL pointer dereference at 00000010
IP: [<c1266c36>] ssb_is_sprom_available+0x16/0x30
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

sparse correctly complains that
__ieee80211_get_channel_mode is not static.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fixes:

drivers/net/wireless/libertas/rx.c: In function process_rxed_802_11_packet:
drivers/net/wireless/libertas/rx.c:354: error: radiotap_hdr.flags may be used uninitialized in this function
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This bug was introduced by the following commit

	Author: Vasanthakumar Thiagarajan <vasanth@atheros.com>
	Date:   Thu Apr 15 17:38:46 2010 -0400

	ath9k: Remove ATH9K_TX_SW_ABORTED and introduce a bool for this purpose

Wrong buffer is checked for bf_tx_aborted field in ath_tx_num_badfrms(),
this may result in a rate scaling with wrong feedback (number
of unacked frames in this case). It is the last one in the chain
of buffers for an aggregate frame that should be checked.

Also it misses the initialization of this field in the buffer,
this may lead to a situation where we stop the sw retransmission
of failed subframes associated to this buffer.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath_print in xmit.c should say "Reseting hardware"
instead of Resetting HAL!(since HAL is being fazed out).
dmesg shows:
[ 8660.899624] ath: Failed to stop TX DMA in 100 msec after killing last frame
[ 8660.899676] ath: Unable to stop TxDMA. Reset HAL!
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Commit "ar9170: wait for asynchronous firmware loading"
introduced a bug, which is triggered by fatal errors
while the driver is initializing the device.

BUG: unable to handle kernel paging request at 6b6b6bf7
IP: [<c117b567>] kobject_put+0x7/0x70
*pde = 00000000
Oops: 0000 [#1] PREEMPT
last sysfs file: /sys/devices/platform/hdaps/position
Modules linked in: ar9170usb [...]

Pid: 6246, comm: firmware/ar9170 Not tainted 2.6.34-wl #54
EIP: 0060:[<c117b567>] EFLAGS: 00010206 CPU: 0
EIP is at kobject_put+0x7/0x70
EAX: 6b6b6bd7 EBX: f4d3d0e0 ECX: f5ba9124 EDX: f6af2a7c
ESI: 00000000 EDI: f4d3d0e0 EBP: 00000000 ESP: f5e98f9c
 DS: 007b ES: 007b FS: 0000 GS: 0000 SS: 0068
Process firmware/ar9170 (pid: 6246)
Stack:
 c12532ed 00000246 f5bfaa70 f8487353 f4d3d0e0
Call Trace:
 [<c12532ed>] ? device_release_driver+0x1d/0x30
 [<f8487353>] ? ar9170_usb_firmware_failed+0x43/0x70 [ar9170usb]
 [<c125983c>] ? request_firmware_work_func+0x2c/0x70
 [<c1259810>] ? request_firmware_work_func+0x0/0x70
 [<c10413f4>] ? kthread+0x74/0x80
 [<c1041380>] ? kthread+0x0/0x80
 [<c1003136>] ? kernel_thread_helper+0x6/0x10
Code: 40 d3 f2 ff 85 c0 89 c3 74 0a ba 44 86 4c c1 e8 [...]
EIP: [<c117b567>] kobject_put+0x7/0x70 SS:ESP 0068:f5e98f9c
CR2: 000000006b6b6bf7
---[ end trace e81abb992434b410 ]---
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This reverts commit 663cb47c.

This patch was merged out of the proper order, so instead of fixing a
problem with a prior (unmerged) patch, it creates one.  Ooops!
Signed-off-by: John W. Linville <linville@tuxdriver.com>

With VEOL, Beacon transmission in ad-hoc does not currently work.
I believe for larger ad-hoc networks, VEOL is too unreliable, as
it can get beacon transmissions stuck during synchronization.
Use SWBA based beacon trasmission similar to AP mode instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This fixes IBSS beacon transmissions without VEOL enabled
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The functionality to keep the device awake until it is done with
the rx of any mcast/bcast frames which are pending on AP should
also be added to the hardwares which support auto sleep feature.
This patch fixes frequent failures in ARP resolution when it is
initiated by the other end. Currently auto sleep is enabled only
for ar9003 in ath9k.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix sta_info.h kernel-doc warnings:

Warning(net/mac80211/sta_info.h:164): No description found for parameter 'tid_active_rx[STA_TID_NUM]'
Warning(net/mac80211/sta_info.h:164): Excess struct/union/enum/typedef member 'tid_state_rx' description in 'sta_ampdu_mlme'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix kernel-doc warnings in mac80211.h:

Warning(include/net/mac80211.h:838): No description found for parameter 'ap_addr'
Warning(include/net/mac80211.h:1726): No description found for parameter 'get_survey'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The intent here is to test that "sta_id_r" is a valid pointer.  We do
this same test later on in the function.

Btw iwl_add_bssid_station() is called from two places and "sta_id_r" is
a valid pointer from both callers.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This is obviously a small picky thing.  The original error handling code
doesn't free the most recent allocations which haven't been added to the
hif_dev->tx.tx_buf list yet.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

After c11d8f89: "ath9k_htc: Simplify TX URB management" we no longer
assume that tx_buf is a non-null pointer.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The recent changes to skb handling introduced a bug in the rt2800usb
TX descriptor writing whereby the length of the USB packet wasn't
calculated correctly.
Found via code inspection, as the devices themselves didn't seem to mind.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

(Based on a patch created by Ondrej Zary)

In some circumstances the Ralink devices do not properly go to sleep
or wake up, with timeouts occurring.
Fix this by retrying telling the device that it has to wake up or
sleep.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This reverts commit 03ceedea.

This patch was reported to cause a regression in which connectivity is
lost and cannot be reestablished after a suspend/resume cycle.
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Implicit slab.h inclusion via percpu.h is about to go away.  Make sure
gfp.h or slab.h is included as necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Don't use to_pci_dev in rt2x00pci_uninitialize to get the allocated irq
as it won't work for platform devices (SoC). Instead, use the irq field
that's already used everywhere else.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We should use the same buffer size we set up for DMA also in the hardware
descriptor. Previously we used common->rx_bufsize for setting up the DMA
mapping, but used skb_tailroom(skb) for the size we tell to the hardware in the
descriptor itself. The problem is that skb_tailroom(skb) can give us a larger
value than the size we set up for DMA before. This allows the hardware to write
into memory locations not set up for DMA. In practice this should rarely happen
because all packets should be smaller than the maximum 802.11 packet size.

On the tested platform rx_bufsize is 2528, and we allocated an skb of 2559
bytes length (including padding for cache alignment) but sbk_tailroom() was
2592. Just consistently use rx_bufsize for all RX DMA memory sizes.

Also use the return value of the descriptor setup function.

Cc: stable@kernel.org
Signed-off-by: Bruno Randolf <br1@einfach.org>
Reviewed-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Specifying a valid channel type will get
goto out rather than continuing, due to
missing braces. This affects both remain
on channel and action frame TX commands.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Remove (hopefully) last use of WEXT in rndis_wlan. Replace wireless_send_event
with missing cfg80211_disconnected in rndis_wlan_do_link_down_work.
Reported-by: "Rogério Brito" <rbrito@ime.usp.br>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We tried to squeeze as much AR9003 support into this kernel
release cycle but there are a few features which are still
being tested and developed. Some of these features are critical
to the stable operation of AR9003 so for now disable AR9003 support
all together. This will get re-enabled once all necessary features
are in place but very likely will not happen for 2.6.35.
Reviewed-by: Don Breslin <don.breslin@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since wdev can be NULL, check it before dereferencing it
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The current frame length used by the driver for RX frames is the SPI bus
transfer length. This length has padding bytes, which do not belong to the
WLAN frame.

As there is no other length information in the WLAN frame except the skb
length this problem caused for instance extra ESSID's to be listed at the
end of scan results (IE id 0) with zero length.

Fix the frame length by removing padding.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>