Merge tag 'imx-fixes-4.0' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes

Pull "The i.MX fixes for 4.0" from Shawn Guo:

It includes a couple of i.MX6 dts fixes, which set an input supply to
vbus regulator.  Without the fixes, the voltage of vbus is incorrect
after system boots up.

* tag 'imx-fixes-4.0' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: imx6sl-evk: set swbst_reg as vbus's parent reg
  ARM: imx6qdl-sabresd: set swbst_reg as vbus's parent reg

Commit 7ef077a8 ("usb: isp1760: Move driver from drivers/usb/host/
to drivers/usb/isp1760/") moved the isp1760 driver and changed the
Kconfig option. This makes CONFIG_USB_ISP1760_HCD not selectable
directly anymore. This results in driver being not compiled in when
using vexpress_defconfig and the USB is non-functional.

This patch updates the CONFIG_USB_ISP1760_HCD to CONFIG_USB_ISP1760 to
get back USB functional on vexpress platforms.

Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reported-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Make the digicolor specific DT_MACHINE_START entry visible.

Fixes: df8d742e (ARM: initial support for Conexant Digicolor CX92755 SoC)
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'fixes-v4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Pull "omap fixes against v4.0-rc2" from Tony Lindgren:

Fixes for various omap variants, mostly minor fixes for various SoCs
with the bigger changes being for the dra7 clocks and hwmod data:

- Fix wl12xx for dm3730-evm

- Fix omap4 prm save and clea

- Fix hwmod clkdm use count

- Fix hwmod data for pcie on dra7

- Fix lockdep for hwmod

- Fix USB on most omap3 boars by enabling it in the defconfig

- Fix the bypass clock source for omap5 and dra7

- Fix the ehrpwm clock for am33xx and am43xx

- Enable AES and SHAM for BeagleBone white

- Use rmii clock for am335x-lxm

- Fix polling intervals for omap5 thermal zones

- Fix slewctrl for am33xx and am43xx

- Fix dra7-evm dcan pinctrl

* tag 'fixes-v4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP2+: Fix wl12xx on dm3730-evm with mainline u-boot
  ARM: OMAP: enable TWL4030_USB in omap2plus_defconfig
  ARM: dts: dra7x-evm: avoid possible contention while muxing on CAN lines
  ARM: dts: dra7x-evm: Don't use dcan1_rx.gpio1_15 in DCAN pinctrl
  ARM: dts: am43xx: fix SLEWCTRL_FAST pinctrl binding
  ARM: dts: am33xx: fix SLEWCTRL_FAST pinctrl binding
  ARM: dts: OMAP5: fix polling intervals for thermal zones
  ARM: dts: am335x-lxm: Use rmii-clock-ext
  ARM: dts: am335x-bone-common: enable aes and sham
  ARM: dts: am43xx-clocks: Fix ehrpwm tbclk data on am43xx
  ARM: dts: am33xx-clocks: Fix ehrpwm tbclk data on am33xx
  ARM: dts: OMAP5: Fix the bypass clock source for dpll_iva and others
  ARM: dts: DRA7x: Fix the bypass clock source for dpll_iva and others
  ARM: OMAP4+: PRM: fix omap4 version of prm_save_and_clear_irqen
  ARM: OMAP2+: hwmod: fix deassert hardreset clkdm usecounting
  ARM: DRA7: hwmod_data: Fix hwmod data for pcie
  ARM: omap2+: omap_hwmod: Set unique lock_class_key per hwmod

This patch adds support to STiH410 SoC.

Please note "st,stih410" is already present in device tree.
The problem is that it is missing the entry in the match table,
and so the L2 cache and other cpus than 0 don't get initialized.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Tested-by: Maxime Coquelin <maxime.coquelin@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'at91-fixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into fixes

Pull "Second fixes batch for AT91 on 4.0" from Nicolas Ferre:

- little fix for !MMU debug: may also help for randconfig
- fix of 2 errors in LCD clock definitions
- in PM code, not writing the key leads to not execute the action

* tag 'at91-fixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
  ARM: at91/pm: MOR register KEY was missing
  ARM: at91/dt: sama5d4: fix lcdck clock definition
  ARM: at91/dt: sama5d4: rename lcd_clk into lcdc_clk
  ARM: at91: debug: fix non MMU debug

Pull "Fixes for v4.0 on the SoCFPGA platform" from Dinh Nguyen:

- Fix the SCU virtual mapping
- Add misssing DMA channels for UART nodes
- Fix a sporadic SMP error where CPU1 was not seeing its start address

* tag 'socfpga_fixes_for_v4.0' of git://git.rocketboards.org/linux-socfpga-next:
  ARM: socfpga: make sure socfpga_cpu1start_addr is properly flushed
  ARM: socfpga: fix uart DMA binding error
  ARM: socfpga: Correct SCU virtual mapping in socfpga

Add Freescale Vybrid family as a own entry, along with an entry for
the so far orphan Vybrid device tree files. Also add myself as
a designated reviewer.
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Removing myself as a co-maintainer.
Signed-off-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

USB vbus 5V is from PMIC SWBST, so set swbst_reg as vbus's
parent reg, it fixed a bug that the voltage of vbus is incorrect
due to swbst_reg is disabled after boots up.

Cc: stable@vger.kernel.org
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

USB vbus 5V is from PMIC SWBST, so set swbst_reg as vbus's
parent reg, it fixed a bug that the voltage of vbus is incorrect
due to swbst_reg is disabled after boots up.

Cc: stable@vger.kernel.org
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

I upgraded my u-boot and noticed that wl12xx stopped working.
Turns out the kernel is not setting the quirk for the MMC2
copy clock while the eariler bootloader I had was setting it.
Signed-off-by: Tony Lindgren <tony@atomide.com>

Merge tag 'for-v4.0-rc/omap-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v4.0/fixes

ARM: OMAP2+: first set of hwmod and PRCM fixes for v4.0-rc

This series fixes the following bugs:

- a lockdep problem with the OMAP hwmod code;
- incorrect PCIe hwmod data for the DRA7xx chips;
- the clockdomain handling in the hardreset deassertion code,
  preventing idle;
- the use of an IRQ status register rather than an IRQ enable register
  in the OMAP4 PRM code.

Basic build, boot, and PM test results are available here:

http://www.pwsan.com/omap/testlogs/omap-hwmod-a-for-v4.0-rc/20150301165949/

Enable TWL4030_USB which is used at least on Nokia N900/N950/N9 (OMAP3)
and BeagleBoard.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>

DCAN1 RX and TX lines are internally pulled high according to [1].
While muxing between DCAN mode and SAFE mode we make sure
that the same pull direction is set to minimize opposite
pull contention during the switching window.

[1] in DRA7 data manual, Ball characteristics table 4-2, DSIS colum shows
the state driven to the peripheral input while in the deselcted mode.
DSIS - De-Selected Input State.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Rev.F onwards ball G19 (dcan1_rx) is used as a GPIO for some other
function so don't include it in DCAN pinctrl node.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

According to AM437x TRM, Document SPRUHL7B, Revised December 2014,
Section 7.2.1 Pad Control Registers, setting bit 19 of the pad control
registers actually sets the SLEWCTRL value to slow rather than fast as
the current macro indicates. Introduce a new macro, SLEWCTRL_SLOW, that
sets the bit, and modify SLEWCTRL_FAST to 0 but keep it for
completeness.

Current users of the macro (i2c, mdio, and uart) are left unmodified as
SLEWCTRL_FAST was the macro used and actual desired state. Tested on
am437x-gp-evm with no difference in software performance seen.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

According to AM335x TRM, Document spruh73l, Revised February 2015,
Section 9.2.2 Pad Control Registers, setting bit 6 of the pad control
registers actually sets the SLEWCTRL value to slow rather than fast as
the current macro indicates. Introduce a new macro, SLEWCTRL_SLOW, that
sets the bit, and modify SLEWCTRL_FAST to 0 but keep it for
completeness.

Current users of the macro (i2c and mdio) are left unmodified as
SLEWCTRL_FAST was the macro used and actual desired state. Tested on
am335x-gp-evm with no difference in software performance seen.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

OMAP4 has a finer counter granularity, which allows for a delay of 1000ms
in the thermal zone polling intervals. OMAP5 has a different counter
mechanism, which allows at maximum a 500ms timer. Adjust the cpu thermal
zone polling interval accordingly.

Without this patch, the polling interval information is simply ignored,
and the following thermal warnings are printed during boot (assuming
thermal is enabled);

[    1.545343] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
[    1.552691] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
[    1.560029] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use external clock for RMII since the internal clock doesn't meet the
jitter requirements.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Beaglebone Black doesn't have AES and SHAM enabled like the
original Beaglebone White dts. This breaks applications that
leverage the crypto blocks so fix this by enabling these nodes
in the am335x-bone-common.dtsi. With this change, enabling the
nodes in am335x-bone.dts is no longer required so remove them.
Signed-off-by: Matt Porter <mporter@konsulko.com>
Acked-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

ehrpwm tbclk is wrongly modelled as deriving from dpll_per_m2_ck.
The TRM says tbclk is derived from SYSCLKOUT. SYSCLKOUT nothing but the
functional clock of pwmss (l4ls_gclk).
Fix this by changing source of ehrpwmx_tbclk to l4ls_gclk.

Fixes: 4da1c677 ("add tbclk data for ehrpwm")
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

ehrpwm tbclk is wrongly modelled as deriving from dpll_per_m2_ck.
The TRM says tbclk is derived from SYSCLKOUT. SYSCLKOUT nothing but the
functional clock of pwmss (l4ls_gclk).
Fix this by changing source of ehrpwmx_tbclk to l4ls_gclk.

Fixes: 9e100eba: ("Fix ehrpwm tbclk data")
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fixes 85dc74e9 (ARM: dts: omap5 clock data)

On OMAP54xx, For DPLL_IVA, the ref clock(CLKINP) is connected to sys_clk1 and
the bypass input(CLKINPULOW) is connected to iva_dpll_hs_clk_div clock.
But the bypass input is not directly routed to bypass clkout instead
both CLKINP and CLKINPULOW are connected to bypass clkout via a mux.

This mux is controlled by the bit - CM_CLKSEL_DPLL_IVA[23]:DPLL_BYP_CLKSEL
and it's POR value is zero which selects the CLKINP as bypass clkout.
which means iva_dpll_hs_clk_div is not the bypass clock for dpll_iva_ck

Fix this by adding another mux clock as parent in bypass mode.

This design is common to most of the PLLs and the rest have only one bypass
clock. Below is a list of the DPLLs that need this fix:

DPLL_IVA,
DPLL_PER,
DPLL_USB and DPLL_CORE
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fixes: ee6c7507 (ARM: dts: dra7 clock data)

On DRA7x, For DPLL_IVA, the ref clock(CLKINP) is connected to sys_clk1 and
the bypass input(CLKINPULOW) is connected to iva_dpll_hs_clk_div clock.
But the bypass input is not directly routed to bypass clkout instead
both CLKINP and CLKINPULOW are connected to bypass clkout via a mux.

This mux is controlled by the bit - CM_CLKSEL_DPLL_IVA[23]:DPLL_BYP_CLKSEL
and it's POR value is zero which selects the CLKINP as bypass clkout.
which means iva_dpll_hs_clk_div is not the bypass clock for dpll_iva_ck

Fix this by adding another mux clock as parent in bypass mode.

This design is common to most of the PLLs and the rest have only one bypass
clock. Below is a list of the DPLLs that need this fix:

DPLL_IVA, DPLL_DDR,
DPLL_DSP, DPLL_EVE,
DPLL_GMAC, DPLL_PER,
DPLL_USB and DPLL_CORE
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Because writing the MOR register requires the PASSWD(0x37),
if missed, the write operation will be aborted.
Signed-off-by: Patrice Vilchez <patrice.vilchez@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

lcdck takes mck (not smd) as its parent. It is also assigned id 3 and not 4.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
[nicolas.ferre@atmel.com: squashed 2 related patches]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Rename lcd_clk into lcdc_clk to be consistent with sama5d3 clock
definitions.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Linux may be used without MMU on atmel SoCs, fix debug in this configuration.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The HiSilicon HiP04 has 16 CPUs. I propose we increase the maximum number of CPUs to 16 to avoid the following warning identified during automated boot testing [1].

------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at ../arch/arm/kernel/devtree.c:144 arm_dt_init_cpu_maps+0x118/0x1e8()
DT /cpu 9 nodes greater than max cores 8, capping them
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 3.19.0-00528-gbdccc4ed #1
Hardware name: Hisilicon HiP04 (Flattened Device Tree)
[] (unwind_backtrace) from [] (show_stack+0x10/0x14)
[] (show_stack) from [] (dump_stack+0x78/0x94)
[] (dump_stack) from [] (warn_slowpath_common+0x74/0xb0)
[] (warn_slowpath_common) from [] (warn_slowpath_fmt+0x30/0x40)
[] (warn_slowpath_fmt) from [] (arm_dt_init_cpu_maps+0x118/0x1e8)
[] (arm_dt_init_cpu_maps) from [] (setup_arch+0x638/0x9a0)
[] (setup_arch) from [] (start_kernel+0x8c/0x3b4)
[] (start_kernel) from [<10208074>] (0x10208074)
---[ end trace cb88537fdc8fa200 ]---

[1] http://storage.kernelci.org/mainline/v3.19-528-gbdccc4edeb03/arm-multi_v7_defconfig/lab-tbaker/boot-hip04-d01.html

Cc: Olof Johansson <olof@lixom.net>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

The a80 optimus has 8 CPUs. I propose we increase the maximum number of CPUs to 8 to avoid the following warning identified during automated boot testing [1].

------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at ../arch/arm/kernel/devtree.c:144 arm_dt_init_cpu_maps+0x110/0x1e0()
DT /cpu 5 nodes greater than max cores 4, capping them
CPU: 0 PID: 0 Comm: swapper Not tainted 3.19.0-00528-gbdccc4ed #1
Hardware name: Allwinner sun9i Family
[] (unwind_backtrace) from [] (show_stack+0x10/0x14)
[] (show_stack) from [] (dump_stack+0x74/0x90)
[] (dump_stack) from [] (warn_slowpath_common+0x70/0xac)
[] (warn_slowpath_common) from [] (warn_slowpath_fmt+0x30/0x40)
[] (warn_slowpath_fmt) from [] (arm_dt_init_cpu_maps+0x110/0x1e0)
[] (arm_dt_init_cpu_maps) from [] (setup_arch+0x634/0x8d4)
[] (setup_arch) from [] (start_kernel+0x88/0x3ac)
[] (start_kernel) from [<20008074>] (0x20008074)
---[ end trace cb88537fdc8fa200 ]---

[1] http://storage.kernelci.org/mainline/v3.19-528-gbdccc4edeb03/arm-sunxi_defconfig/lab-tbaker/boot-sun9i-a80-optimus.html

Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into fixes

Merge "First fixes batch for AT91 on 4.0" from Nicolas Ferre:

- PM slowclock fixes for DDR and timeouts
- fix some DT entries
- little defconfig updates
- the removal of a harmful watchdog option + its detailed documentation

* tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
  ARM: at91/dt: keep watchdog running in idle mode
  dts: Documentation: AT91 Watchdog, explain what atmel,idle-halt property really do
  ARM: at91/defconfig: add at91rm9200 ethernet support
  ARM: at91/defconfig: remove CONFIG_SYSFS_DEPRECATED
  ARM: at91/dt: at91sam9260: fix usart pinctrl
  ARM: at91/dt: sama5d4: add missing alias for i2c0
  ARM: at91/dt: at91sam9263: Fixup sram1 device tree node
  ARM: at91: pm: fix SRAM allocation
  ARM: at91: pm: fix at91rm9200 standby
  pm: at91: Workaround DDRSDRC self-refresh bug with LPDDR1 memories.
  pm: at91: pm_slowclock: fix suspend/resume hang up in timeouts

Merge tag 'samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes

Merge "Samsung fixes for v4.0" from Kukjin Kim:

* tag samsung-fixes-1:
  ARM: EXYNOS: Fix wrong hwirq of RTC interrupt for Exynos3250 SoC
  ARM: EXYNOS: Don't use LDREX and STREX after disabling cache coherency

Merge tag 'samsung-fixes-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes

Merge "Samsung tmu and hdmi regression fixes for v4.0" from Kukjin Kim:

- The thermal management unit and HDMI (drm mixer driver) related
reworks have been merged in v4.0 merge window. So if this DT changes
are missed for v4.0, we regressions in v4.0 release for exynos
platforms such as exynos5250, exynos5420, exynos4 SoCs.

- Note since there was a dependency with driver side, this cannot
be sent to upstream during preivous merge window and now it has been
resolved.

* tag 'samsung-fixes-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: dts: add display power domain for exynos5250
  ARM: dts: add 'hdmi' clock to mixer nodes for exynos5250 and exynos5420
  ARM: dts: enable hdmi support for exynos4210-universal_c210
  ARM: dts: enable hdmi support for exynos4412-odroid-common
  ARM: dts: add dependency between TV and LCD0 power domains for exynos4
  ARM: dts: add hdmi related nodes for exynos4 SoCs
  ARM: EXYNOS: add support for sub-power domains
  dt-bindings: document a note about power domain subdomains
  ARM: dts: Provide dt bindings identical for Exynos TMU
  ARM: dts: Trip points and sensor configuration data for exynos5440
  ARM: dts: define default thermal-zones for exynos4
  ARM: dts: default trip points definition for exynos5420
  ARM: dts: add TMU default definitions for exynos4412
  ARM: dts: Adding CPU cooling binding for Exynos SoCs
  ARM: dts: Enable TMU for exynos4412-odriod-common
  ARM: dts: Add LDO10 for TMU for exynos4412-odroid-common
  ARM: dts: Enable TMU for exynos4210-trats

Make sure socfpga_cpu1start_addr is properly flushed from it's cache line so
that secondary cpu's can see it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>

socfpga.dtsi is missing the DMA channels for the uart nodes.
This will produce the following errors:

	of_dma_request_slave_channel: dma-names property of node '/soc/serial0@ffc02000' missing or empty
	ttyS0 - failed to request DMA

Provide the correct DMA channels to fix this.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>

Correct SCU virtual mapping that was causing this BUG message:

"BUG: mapping for 0xfffec000 at 0xfffec000 out of vmalloc space"
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>

Since turning on idle-halt in commit fe46aa67 (ARM: at91/dt: add
sam9 watchdog default options to SoCs), SoCs compatible with at91sam9260-wdt
no longer reboot if the watchdog times out while the CPU is in idle state.
Removing the 'idle-halt' flag that was set by default fixes this.
Signed-off-by: Michel Marti <mma@objectxp.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
[nicolas.ferre@atmel.com: rework the commit message]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

atmel,idle-halt property should be used with care, it actually makes the
watchdog not counting when the CPU is in idle state, therefore the
watchdog reset time depends on mean CPU usage and will not reset at all
of the CPU stop working while it is in idle state, which is probably not
what you want.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

There is now only one defconfig for the at91rm9200 and at91sam9. Add ethernet
support for the at91rm9200.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>