- 07 Feb, 2006 32 commits
-
-
Grant C. Likely authored
Signed-off-by:
Grant C. Likely <grant.likely@secretlab.ca> Signed-off-by:
Paul Mackerras <paulus@samba.org>
-
Grant C. Likely authored
Includes fix for Xilinx silicon errata 213 Signed-off-by:
-
Grant C. Likely authored
Signed-off-by:
-
Grant C. Likely authored
Signed-off-by:
-
Grant C. Likely authored
Signed-off-by:
-
Grant C. Likely authored
Signed-off-by:
-
Grant C. Likely authored
This patch only deals with the serial port definitions as there is no support for any other xilinx IP cores in the kernel tree at the moment. Board specific configuration moved out of virtex.[ch] and into the xparameters.h wrapper. This also prepares for the transition to the flattened device tree model. When the bootloader provides a device tree generated from an xparameters.h files, the kernel will no longer need xparameters/*. The platform bus will get populated with data from the device tree, and the device drivers will be automatically connected to the devices. Only the bootloader (or ppcboot) will need xparameters directly. Signed-off-by:
-
Grant C. Likely authored
The PPC405 hard core is used in both the Virtex-II Pro and Virtex 4 FX FPGAs. This patch cleans up the Virtex naming convention to reflect more than just the Virtex-II Pro. Rename files virtex-ii_pro.[ch] to virtex.[ch] Rename config value VIRTEX_II_PRO to XILINX_VIRTEX Signed-off-by:
-
Grant C. Likely authored
xparameters should not be needed by anything but virtex platform code. Move it from include/asm-ppc/ to platforms/4xx/xparameters/ This is preparing for work to remove xparameters from the dependancy tree for most c files. xparam changes should not cause a recompile of the world. Instead, drivers should get device info from the platform bus (populated by the boot code) Signed-off-by:
-
Nathan Lynch authored
When a cpu is hotplug-onlined, if we don't set per_cpu(last_jiffy) to something sane, timer_interrupt will execute its while loop for every tick missed since the cpu was last online (or since the system was booted, if we're adding a new cpu). This can cause weird hangs, ssh sessions dropping, and we can even go xmon if we take a global IPI at the wrong time. Signed-off-by:
Nathan Lynch <ntl@pobox.com> Signed-off-by:
-
Michael Neuling authored
We call unregister_vpa but we don't check to see if the hypervisor supports this. Signed-off-by:
Michael Neuling <mikey@neuling.org> Acked-by:
Anton Blanchard <anton@samba.org> -- arch/powerpc/platforms/pseries/setup.c | 2 +- 1 files changed, 1 insertion(+), 1 deletion(-) Signed-off-by:
-
Becky Bruce authored
Updated SOC node definition in documentation to include bus-frequency property. Also extended mdio example to match specification. Signed-off-by:
Becky Bruce <becky.bruce@freescale.com> Signed-off-by:
Kumar Gala <galak@gate.crashing.org> Signed-off-by:
-
Michael Ellerman authored
Since 404849bb we've been using LOAD_REG_ADDRBASE, which uses the toc pointer, in decrementer_iSeries_masked. This can explode if we take the decrementer interrupt while we're in a module, because the toc pointer in r2 will be the module's toc pointer. Signed-off-by:
Michael Ellerman <michael@ellerman.id.au> Signed-off-by:
-
David Gibson authored
The code to mark a page as icache dirty (so that it will later be icache-dcache flushed when we try to execute from it) is duplicated in three places: flush_dcache_page() does this marking and nothing else, but clear_user_page() and copy_user_page() duplicate it, since those functions make the page icache dirty themselves. This patch makes those other functions call flush_dcache_page() instead, so the logic's all in one place. This will make life less confusing if we ever need to tweak the details of the the lazy icache flush mechanism. arch/powerpc/mm/mem.c | 14 ++------------ 1 file changed, 2 insertions(+), 12 deletions(-) Signed-off-by:
David Gibson <dwg@au1.ibm.com> Signed-off-by:
-
Jesper Juhl authored
Checking a pointer for NULL before passing it to kfree is pointless, kfree does its own NULL checking of input. Signed-off-by:
Jesper Juhl <jesper.juhl@gmail.com> Signed-off-by:
-
Olaf Hering authored
arch/powerpc/kernel/udbg_16550.c: In function `udbg_init_maple_realmode': arch/powerpc/kernel/udbg_16550.c:162: warning: assignment from incompatible pointer type Signed-off-by:
Olaf Hering <olh@suse.de> Signed-off-by:
-
Olaf Hering authored
setup_peg2 must do some refcounting. of_get_pci_address may need to drop the node Pegasos l2cr : L2 cache was not active, activating PCI bus 0 controlled by pci at 80000000 Badness in kref_get at /home/olaf/kernel/olh/ppc64/linux-2.6.16-rc2-olh/lib/kref.c:32 Call Trace: [C037BD00] [C0007934] show_stack+0x5c/0x184 (unreliable) [C037BD30] [C000E068] program_check_exception+0x184/0x584 [C037BD90] [C000F5F0] ret_from_except_full+0x0/0x4c --- Exception: 700 at kref_get+0xc/0x24 LR = of_node_get+0x24/0x3c [C037BE50] [C004FD94] __pte_alloc_kernel+0x64/0x80 (unreliable) [C037BE70] [C000CA18] of_get_parent+0x34/0x58 [C037BE90] [C0009B18] of_get_address+0x24/0x174 [C037BED0] [C000A108] of_address_to_resource+0x24/0x68 [C037BF00] [C038B128] chrp_find_bridges+0x114/0x470 [C037BF90] [C038AE48] chrp_setup_arch+0x1fc/0x32c [C037BFB0] [C03849B0] setup_arch+0x144/0x188 [C037BFD0] [C037C45C] start_kernel+0x34/0x1a8 [C037BFF0] [000037A0] 0x37a0 Badness in kref_get at /home/olaf/kernel/olh/ppc64/linux-2.6.16-rc2-olh/lib/kref.c:32 Call Trace: [C037BC90] [C0007934] show_stack+0x5c/0x184 (unreliable) [C037BCC0] [C000E068] program_check_exception+0x184/0x584 [C037BD20] [C000F5F0] ret_from_except_full+0x0/0x4c --- Exception: 700 at kref_get+0xc/0x24 LR = of_node_get+0x24/0x3c [C037BDE0] [00000000] 0x0 (unreliable) [C037BE00] [C000CA18] of_get_parent+0x34/0x58 [C037BE20] [C0009CE8] of_translate_address+0x2c/0x2fc [C037BEA0] [C0009FE8] __of_address_to_resource+0x30/0xc4 [C037BED0] [C000A130] of_address_to_resource+0x4c/0x68 [C037BF00] [C038B128] chrp_find_bridges+0x114/0x470 [C037BF90] [C038AE48] chrp_setup_arch+0x1fc/0x32c [C037BFB0] [C03849B0] setup_arch+0x144/0x188 [C037BFD0] [C037C45C] start_kernel+0x34/0x1a8 [C037BFF0] [000037A0] 0x37a0 PCI bus 0 controlled by pci at c0000000 Top of RAM: 0x10000000, Total RAM: 0x10000000 Signed-off-by:
-
Olaf Hering authored
remove pointer/integer confusion Signed-off-by:
-
Olaf Hering authored
Use generic_calibrate_decr to restore missing clock: speed in /proc/cpuinfo Signed-off-by:
-
Olaf Hering authored
remove pointer/integer confusion Signed-off-by:
-
Michael Ellerman authored
It's possible for prom_init to allocate the flat device tree inside the kdump crash kernel region. If this happens, when we load the kdump kernel we overwrite the flattened device tree, which is bad. We could make prom_init try and avoid allocating inside the crash kernel region, but then we run into issues if the crash kernel region uses all the space inside the RMO. The easiest solution is to move the flat device tree once we're running in the kernel. Signed-off-by:
-
Dave C Boutcher authored
It turns out that we can't stop the watchdog from triggering here. If we touch the timer (which just uses the current jiffie value) before we enable interrupts, it does nothing because jiffies are not mass-updated until after we enable interrupts. If we touch the timer after we enable interrupts, its too late because the softlockup watchdog will already have triggered. The touch_softlockup_watchdog call removed below does nothing. Signed-off-by:
Dave Boutcher <sleddog@us.ibm.com> Signed-off-by:
-
Dave C Boutcher authored
We need to prod everyone here since this is the only CPU that is guaranteed to be running after the ibm,suspend-me RTAS call returns. Signed-off-by:
-
Dave C Boutcher authored
Correctly return the status from the RTAS call. rtas_call expects to return the status as a return value. Signed-off-by:
-
Michael Ellerman authored
arch/powerpc/kernel/rtas.c is getting hvcall.h via spinlock.h, but when we're building for UP we don't include spinlock.h. Signed-off-by:
-
Jake Moilanen authored
This addresses two items, which are unlikely to be hit if we trust drivers. The first is moving a memory barrier below where the vmerged SG count is passed back, but before the list is set to end. If those instructions were reordered, there could be an issue in iommu_unmap_sg(). The second is making sure we terminate the list on the failure case of iommu_map_sg(). If a driver does not look at the failure return code, it could pass a ill-formed SG list to iommu_unmap_sg(). Signed-off-by:
Jake Moilanen <moilanen@austin.ibm.com> Acked-by:
Olof Johansson <olof@lixom.net> Signed-off-by:
-
Michael Ellerman authored
You can't boot a kdump kernel via OF, not reliably anyway, the kernel being at 32 MB conflicts with the zImage wrapper etc. and it blows up. It's trivial to check in prom_init though, and this is early enough that we can actually drop back to OF where a reset-all will get you going again, which is kinda nice. I think this should go in for 2.6.16. Signed-off-by:
-
Michael Ellerman authored
To prevent problems later in boot, make sure we don't create zero-size lmb regions. I've checked all the callers, and at the moment no one should ever hit this. All callers use a constant size, or they check the computed size before they call us. Signed-off-by:
-
Michael Ellerman authored
In prom.c we run finish_node() on allnodes twice. The first time we just calculate how much memory we'll need, the second time we do the actual work. If the calculation stage determines that we need 0 bytes, then we should skip the lmb allocation. Although an alloc of zero will work, it has been seen to lead to a BUG_ON() in reserve_bootmem() on at least one machine. Signed-off-by:
-
Marcelo Tosatti authored
The last two 8MB TLB entries are being incorrectly set by initial_mmu on 8xx. The first entry is written with the same virtual/physical address, which renders it invalid: BDI>rms 792 0x00001e00 BDI>rms 824 1 BDI>rds 824 SPR 824 : 0xc08000c0 -1065353024 BDI>rds 825 SPR 825 : 0xc0800de0 -1065349664 BDI>rds 826 SPR 826 : 0x00000000 0 And the second entry, in addition, does not have its TLB index set correctly. Signed-off-by:
Marcelo Tosatti <marcelo.tosatti@cyclades.com> Signed-off-by:
-
Geoff Levand authored
This is a small fix to get the spufs init sequence right. init_spu_base() in spu_base.c should be called (via module_init(init_spu_base)) before spufs_init() (via module_init(spufs_init)) in spufs/inode.c gets called. Signed-off-by:
Masato Noguchi <Masato.Noguchi@jp.sony.com> Signed-off-by:
Geoff Levand <geoffrey.levand@am.sony.com> Signed-off-by:
-
Paul Mackerras authored
When loading up the FPU, we were using a 'ld' (load doubleword) instruction to get the FP exception mode from the thread_struct, but it's only an int field. This changes the ld to lwz (load word and zero-extend). Signed-off-by:
-
- 06 Feb, 2006 1 commit
-
-
Paul Mackerras authored
-
- 05 Feb, 2006 7 commits
-
-
Greg KH authored
I thought we had fixed up all non-gpl USB drivers, and was wrong to do this. Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by:
Linus Torvalds <torvalds@osdl.org>
-
Linus Torvalds authored
The non-NUMA case would do an unmatched "free_alien_cache()" on an alien pointer that had never been allocated. It might not matter from a code generation standpoint (since in the non-NUMA case, the code doesn't actually _do_ anything), but it not only results in a compiler warning, it's really really ugly too. Fix the compiler warning by just having a matching dummy allocation. That also avoids an unnecessary #ifdef in the code. Signed-off-by: -
Linus Torvalds authored
-
Linus Torvalds authored
-
Robb, Sam authored
On a system where libintl.h is present, but the NLS functionality is supplied by a separate library instead of the system C library, an attempt to "make config" or "make menuconfig" will fail with link errors, ex: scripts/kconfig/mconf.o:mconf.c:(.text+0xf63): undefined reference to `_libintl_gettext' This patch attempts to correct the problem by detecting whether or not NLS support requires linking with libintl. Signed-off-by:Samuel J Robb <sam.robb@timesys.com> Cc: Roman Zippel <zippel@linux-m68k.org> Cc: Sam Ravnborg <sam@ravnborg.org> Signed-off-by:
Andrew Morton <akpm@osdl.org> Signed-off-by:
-
Adrian Bunk authored
Due to the usage of set_64bit in include/asm-i386/pgtable-3level.h, HIGHMEM64G must depend on X86_CMPXCHG64. Signed-off-by:
Adrian Bunk <bunk@stusta.de> Signed-off-by:
-
Takashi Iwai authored
Fix gcc4.1 compile warnings "value computed is not used" with set_current_state() and set_task_state() on i386/SMP and x86-64. Signed-off-by:
Takashi Iwai <tiwai@suse.de> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Andi Kleen <ak@muc.de> Signed-off-by:
-
