Generally the check should be very cheap, as the sk_buff_head is in cache.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ip_rcv_finish_core(), if it does not drop, sets skb->dst by either early
 demux or route lookup.  The last step, calling dst_input(skb), is left to
 the caller; in the listified case, we split to form sublists with a common
 dst, but then ip_sublist_rcv_finish() just calls dst_input(skb) in a loop.
The next step in listification would thus be to add a list_input() method
 to struct dst_entry.

Early demux is an indirect call based on iph->protocol; this is another
 opportunity for listification which is not taken here (it would require
 slicing up ip_rcv_finish_core() to allow splitting on protocol changes).
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Also involved adding a way to run a netfilter hook over a list of packets.
 Rather than attempting to make netfilter know about lists (which would be
 a major project in itself) we just let it call the regular okfn (in this
 case ip_rcv_finish()) for any packets it steals, and have it give us back
 a list of packets it's synchronously accepted (which normally NF_HOOK
 would automatically call okfn() on, but we want to be able to potentially
 pass the list to a listified version of okfn().)
The netfilter hooks themselves are indirect calls that still happen per-
 packet (see nf_hook_entry_hookfn()), but again, changing that can be left
 for future work.

There is potential for out-of-order receives if the netfilter hook ends up
 synchronously stealing packets, as they will be processed before any
 accepts earlier in the list.  However, it was already possible for an
 asynchronous accept to cause out-of-order receives, so presumably this is
 considered OK.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

__netif_receive_skb_core() does a depressingly large amount of per-packet
 work that can't easily be listified, because the another_round looping
 makes it nontrivial to slice up into smaller functions.
Fortunately, most of that work disappears in the fast path:
 * Hardware devices generally don't have an rx_handler
 * Unless you're tcpdumping or something, there is usually only one ptype
 * VLAN processing comes before the protocol ptype lookup, so doesn't force
   a pt_prev deliver
 so normally, __netif_receive_skb_core() will run straight through and pass
 back the one ptype found in ptype_base[hash of skb->protocol].
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

First example of a layer splitting the list (rather than merely taking
 individual packets off it).
Involves new list.h function, list_cut_before(), like list_cut_position()
 but cuts on the other side of the given entry.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netif_receive_skb_list_internal() now processes a list and hands it
 on to the next function.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Improves packet rate of 1-byte UDP receives by up to 10%.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Just calls netif_receive_skb() in a loop.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Xin Long says:

====================
sctp: fully support for dscp and flowlabel per transport

Now dscp and flowlabel are set from sock when sending the packets,
but being multi-homing, sctp also supports for dscp and flowlabel
per transport, which is described in section 8.1.12 in RFC6458.

v1->v2:
  - define ip_queue_xmit as inline in net/ip.h, instead of exporting
    it in Patch 1/5 according to David's suggestion.
  - fix the param len check in sctp_s/getsockopt_peer_addr_params()
    in Patch 3/5 to guarantee that an old app built with old kernel
    headers could work on the newer kernel per Marcelo's point.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The transport with illegal flowlabel should not be allowed to send
packets. Other transport protocols already denies this.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Struct sockaddr_in6 has the member sin6_flowinfo that includes the
ipv6 flowlabel, it should also support for setting flowlabel when
adding a transport whose ipaddr is from userspace.

Note that addrinfo in sctp_sendmsg is using struct in6_addr for
the secondary addrs, which doesn't contain sin6_flowinfo, and
it needs to copy sin6_flowinfo from the primary addr.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

spp_ipv6_flowlabel and spp_dscp are added in sctp_paddrparams in
this patch so that users could set sctp_sock/asoc/transport dscp
and flowlabel with spp_flags SPP_IPV6_FLOWLABEL or SPP_DSCP by
SCTP_PEER_ADDR_PARAMS , as described section 8.1.12 in RFC6458.

As said in last patch, it uses '| 0x100000' or '|0x1' to mark
flowlabel or dscp is set,  so that their values could be set
to 0.

Note that to guarantee that an old app built with old kernel
headers could work on the newer kernel, the param's check in
sctp_g/setsockopt_peer_addr_params() is also improved, which
follows the way that sctp_g/setsockopt_delayed_ack() or some
other sockopts' process that accept two types of params does.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Like some other per transport params, flowlabel and dscp are added
in transport, asoc and sctp_sock. By default, transport sets its
value from asoc's, and asoc does it from sctp_sock. flowlabel
only works for ipv6 transport.

Other than that they need to be passed down in sctp_xmit, flow4/6
also needs to set them before looking up route in get_dst.

Note that it uses '& 0x100000' to check if flowlabel is set and
'& 0x1' (tos 1st bit is unused) to check if dscp is set by users,
so that they could be set to 0 by sockopt in next patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch introduces __ip_queue_xmit(), through which the callers
can pass tos param into it without having to set inet->tos. For
ipv6, ip6_xmit() already allows passing tclass parameter.

It's needed when some transport protocol doesn't use inet->tos,
like sctp's per transport dscp, which will be added in next patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds a DSA driver for:

Vitesse VSC7385 SparX-G5 5-port Integrated Gigabit Ethernet Switch
Vitesse VSC7388 SparX-G8 8-port Integrated Gigabit Ethernet Switch
Vitesse VSC7395 SparX-G5e 5+1-port Integrated Gigabit Ethernet Switch
Vitesse VSC7398 SparX-G8e 8-port Integrated Gigabit Ethernet Switch

These switches have a built-in 8051 CPU and can download and execute
firmware in this CPU. They can also be configured to use an external
CPU handling the switch in a memory-mapped manner by connecting to
that external CPU's memory bus.

This driver (currently) only takes control of the switch chip over
SPI and configures it to route packages around when connected to a
CPU port. The chip has embedded PHYs and VLAN support so we model it
using DSA as a best fit so we can easily add VLAN support and maybe
later also exploit the internal frame header to get more direct
control over the switch.

The four built-in GPIO lines are exposed using a standard GPIO chip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The VSC7385, VSC7388, VSC7395 and VSC7398 are integrated
switch/router chips for 5+1 or 8-port switches/routers. When
managed directly by Linux using DSA we need to do a special
set-up "dance" on the PHY. Unfortunately these sequences
switches the PHY to undocumented pages named 2a30 and 52b6
and does undocumented things. It is described by these opaque
sequences also in the reference manual. This is a best
effort to integrate it anyways.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds the device tree bindings for the Vitesse VSC73xx
switches. We also add the vendor name for Vitesse.

Cc: devicetree@vger.kernel.org
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf-next 2018-07-03

The following pull-request contains BPF updates for your *net-next* tree.

The main changes are:

1) Various improvements to bpftool and libbpf, that is, bpftool build
   speed improvements, missing BPF program types added for detection
   by section name, ability to load programs from '.text' section is
   made to work again, and better bash completion handling, from Jakub.

2) Improvements to nfp JIT's map read handling which allows for optimizing
   memcpy from map to packet, from Jiong.

3) New BPF sample is added which demonstrates XDP in combination with
   bpf_perf_event_output() helper to sample packets on all CPUs, from Toke.

4) Add a new BPF kselftest case for tracking connect(2) BPF hooks
   infrastructure in combination with TFO, from Andrey.

5) Extend the XDP/BPF xdp_rxq_info sample code with a cmdline option to
   read payload from packet data in order to use it for benchmarking.
   Also for '--action XDP_TX' option implement swapping of MAC addresses
   to avoid drops on some hardware seen during testing, from Jesper.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Igor Russkikh says:

====================
net: aquantia: various ethtool ops implementation

In this patchset Anton Mikaev and I added some useful ethtool operations:
- ring size changes
- link renegotioation
- flow control management

The patch also improves init/deinit sequence.

V3 changes:
- After review and analysis it is clear that rtnl lock (which is
  captured by default on ethtool ops) is enough to secure possible
  overlapping of dev open/close. Thus, just dropping internal mutex.

V2 changes:
- using mutex to secure simultaneous dev close/open
- using state var to store/restore dev state
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adds ethtool -r|--negotiate operation support. It triggers special
control bit on FW interface causing FW to restart link negotiation.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Anton Mikaev <amikaev@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Runtime change of pause frame configuration (rx/tx flow control)
via ethtool.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We now pass link drop status to FW on init/deinit. This is required
to inform FW that driver took/released a control on link.
FW then will manage its own state and device power profile based
on this information. To improve management we remove mpi_set
function which ambiguously took both state and speed parameters.

Deinit callback is now a part of FW ops, as it actually manages the FW.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implemented ring size setup, min/max validation and reconfiguration in
runtime.
Signed-off-by: Anton Mikaev <amikaev@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add suffix UL to constant 1024 in order to give the compiler complete
information about the proper arithmetic to use. Notice that this
constant is used in a context that expects an expression of type
u64 (64 bits, unsigned) and  following expressions are currently
being evaluated using 32-bit arithmetic:

qopt->idleslope * 1024 * ptr
qopt->hicredit * 1024 * 8
qopt->locredit * 1024 * 8

Addresses-Coverity-ID: 1470246 ("Unintentional integer overflow")
Addresses-Coverity-ID: 1470248 ("Unintentional integer overflow")
Addresses-Coverity-ID: 1470249 ("Unintentional integer overflow")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If SGMII was selected in the DT then the device should
write the SGMII enable bit.

If SGMII is not selected in the DT then the SGMII bit
should be disabled.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add INT_STAT3 interrupt setting and clearing
support.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simple overlapping changes in stmmac driver.

Adjust skb_gro_flush_final_remcsum function signature to make GRO list
changes in net-next, as per Stephen Rothwell's example merge
resolution.
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull MD fixes from Shaohua Li:
 "Two small fixes for MD:

   - an error handling fix from me

   - a recover bug fix for raid10 from BingJing"

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
  md/raid10: fix that replacement cannot complete recovery after reassemble
  MD: cleanup resources in failure

Pull OpenRISC fixes from Stafford Horne:
 "Two fixes for issues which were breaking OpenRISC boot:

   - Fix bug in __pte_free_tlb() exposed in 4.18 by Matthew Wilcox's
     page table flag addition.

   - Fix issue booting on real hardware if delay slot detection
     emulation is disabled"

* tag 'for-linus' of git://github.com/stffrdhrn/linux:
  openrisc: entry: Fix delay slot exception detection
  openrisc: Call destructor during __pte_free_tlb

Pull networking fixes from David Miller:

 1) Verify netlink attributes properly in nf_queue, from Eric Dumazet.

 2) Need to bump memory lock rlimit for test_sockmap bpf test, from
    Yonghong Song.

 3) Fix VLAN handling in lan78xx driver, from Dave Stevenson.

 4) Fix uninitialized read in nf_log, from Jann Horn.

 5) Fix raw command length parsing in mlx5, from Alex Vesker.

 6) Cleanup loopback RDS connections upon netns deletion, from Sowmini
    Varadhan.

 7) Fix regressions in FIB rule matching during create, from Jason A.
    Donenfeld and Roopa Prabhu.

 8) Fix mpls ether type detection in nfp, from Pieter Jansen van Vuuren.

 9) More bpfilter build fixes/adjustments from Masahiro Yamada.

10) Fix XDP_{TX,REDIRECT} flushing in various drivers, from Jesper
    Dangaard Brouer.

11) fib_tests.sh file permissions were broken, from Shuah Khan.

12) Make sure BH/preemption is disabled in data path of mac80211, from
    Denis Kenzior.

13) Don't ignore nla_parse_nested() return values in nl80211, from
    Johannes berg.

14) Properly account sock objects ot kmemcg, from Shakeel Butt.

15) Adjustments to setting bpf program permissions to read-only, from
    Daniel Borkmann.

16) TCP Fast Open key endianness was broken, it always took on the host
    endiannness. Whoops. Explicitly make it little endian. From Yuching
    Cheng.

17) Fix prefix route setting for link local addresses in ipv6, from
    David Ahern.

18) Potential Spectre v1 in zatm driver, from Gustavo A. R. Silva.

19) Various bpf sockmap fixes, from John Fastabend.

20) Use after free for GRO with ESP, from Sabrina Dubroca.

21) Passing bogus flags to crypto_alloc_shash() in ipv6 SR code, from
    Eric Biggers.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits)
  qede: Adverstise software timestamp caps when PHC is not available.
  qed: Fix use of incorrect size in memcpy call.
  qed: Fix setting of incorrect eswitch mode.
  qed: Limit msix vectors in kdump kernel to the minimum required count.
  ipvlan: call dev_change_flags when ipvlan mode is reset
  ipv6: sr: fix passing wrong flags to crypto_alloc_shash()
  net: fix use-after-free in GRO with ESP
  tcp: prevent bogus FRTO undos with non-SACK flows
  bpf: sockhash, add release routine
  bpf: sockhash fix omitted bucket lock in sock_close
  bpf: sockmap, fix smap_list_map_remove when psock is in many maps
  bpf: sockmap, fix crash when ipv6 sock is added
  net: fib_rules: bring back rule_exists to match rule during add
  hv_netvsc: split sub-channel setup into async and sync
  net: use dev_change_tx_queue_len() for SIOCSIFTXQLEN
  atm: zatm: Fix potential Spectre v1
  s390/qeth: consistently re-enable device features
  s390/qeth: don't clobber buffer on async TX completion
  s390/qeth: avoid using is_multicast_ether_addr_64bits on (u8 *)[6]
  s390/qeth: fix race when setting MAC address
  ...

Peng Li says:

====================
net: hns3: a few code improvements

This patchset removes some redundant code and fixes a few code
stylistic issues from internal concentrated review,
no functional changes introduced.

---
Change log:
V1 -> V2:
1, remove a patch according to the comment reported by David Miller.
---
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

For consistency, prefix hnae_ should be modified to hnae3_.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reference to Documentation/DMA-API-HOWTO.txt,
Streaming DMA mappings which are usually mapped for one DMA transfer,
Network card DMA ring descriptors should use Consistent DMA mappings.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Give default option for HNS3_HCLGE and HNS3_ENET will be helpful,
while dependency HNS3 is set. Meanwhile, use "if HNS3" section
instead of all the "depends on HNS3".
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some members in struct hns3_enet_tqp_vector, struct hnae3_client
and struct hnae3_ae_algo are unused.
This patch removes them.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Set complete in the first hclge_cmd_csq_done of hclge_cmd_send,
and check if complete later, unnecessary to do hclge_cmd_csq_done
again.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

csq is used as a ring buffer, the value of the desc will be replaced
in next use. This patch removes the unnecessary memset, and just
updates the next_to_clean.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove some redundant assignments.
desc->flag = cpu_to_le16(HCLGE_CMD_FLAG_NO_INTR | HCLGE_CMD_FLAG_IN)
has set bit HCLGE_CMD_FLAG_WR to zero, so does others.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>