hw code should never use private driver data, but
sometimes we need a backpointer so just stuff it on
the common ath struct.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Linux keeps scan results up to 15 seconds. This can be a problem for fast
moving clients: they get back stale data. But if the kernel reports the age
of the BSS items, then user-space can simply weed out old entries by itself.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This allows for hw support to be enabled for ar9271.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

hw code for Atheros 802.11n hardware is commmon between
different chipsets. This moves this code into a separate
module, the next expected user of this code will be
the ath9k_htc module.

The ath9k/ dir is now selected by ATH9K_HW, an option which
gets selected by either ath9k or ath9k_htc, but remains
invisible for user menuconfig configuration. If either
ath9k or ath9k_htc will be compiled into the kernel
ath9k_hw will also be compiled in.

Cc: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

PCI and debug code will not be shared between ath9k and
ath9k_htc, so make that code use the common read/write ops.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Commenting unused functions lpphy_restore_dig_flt_state and
lpphy_disable_rx_gain_override, may be we need these functions in future.

This also fixed following compilation warnings :
  CC [M]  drivers/net/wireless/b43/phy_lp.o
drivers/net/wireless/b43/phy_lp.c:383: warning: ‘lpphy_restore_dig_flt_state’ defined but not used
drivers/net/wireless/b43/phy_lp.c:891: warning: ‘lpphy_disable_rx_gain_override’ defined but not used
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Ever since Johannes' "iwlwifi: improve scan support" iwlwifi
no longer needs any of lib80211's functions or definitions.

This patch updates iwlwifi's Kconfig _selections_ and
removes all left lib80211.h inclusions from the source files.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

* Get power table offset from the EEPROM instead of using
  a hardcoded value of -5 if the EEPROM rev is >= 21.
* Add support in the 4k eeprom code for tx power offset
  in case we have a 4k AR9280 implementation.
* Fix tx power accuracy at high powers.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This has to be done if the EEPROM supports FCC Midband
capability.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Reduce PLL Settle time and eliminate redundant PLL calls. Also reduce
the LoadNF timeout from 10 msec to 250usec as the 10 msec timeout was
hit with AR9285 in some cases.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Clearing a local variable is unnecessary.
Get rid of it.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

* Move 0xa274 and 0xa27c to the top of tx_gain table.
* Update initvals to fix random failure of noise floor calibration.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For AR5416 chipsets, clearing RTC_RESET_EN when setting
the chip to SLEEP mode results in high power consumption.
This patch fixes this issue by not clearing it for AR5416.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If the current channel is between 2412 and 2472 MHz and if the channel is
changing to 2484 MHz, then the registers 0xa1f4, 0xa1f8 and 0xa1fc need to be
programmed to the "japan_2484" values.  Conversely, if the current channel
is 2484 MHz and if the channel is changing to one between 2412 and 2472 MHz, then
the three registers need to be programmed to the "normal" values.

This is needed for compliance with Japanese regulatory requirements.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

* Prevent divide-by-zero errors in IQ Calibration.
* Do not run temperature compensation if initPDADC or currPDADC is zero.
* Also, introduce a separate function for handling OLC for AR9287.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ar9170_op_get_tsf: handle a carry from TSF_L into TSF_H
by reading TSF_H twice.
Signed-off-by: Joerg Albert <jal2@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

add heavy clip handling for 2.4GHz only (similar to the vendor driver).
Signed-off-by: Joerg Albert <jal2@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes some coding style issues and moves MAX_RATE_POWER into hw.h
Signed-off-by: Joerg Albert <jal2@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The module firmware information of 1000 series is missing from iwlagn.
Signed-off-by: Huaxu Wan <huaxu.wan@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Using powersave while idle saves a lot of power, but
we've had problems with this on some cards (5150 has
been reported to be problematic). However, on the new
6000 series we're seeing no problems, so for now let
that hardware benefit from idle mode, we can look at
the problems with other hardware one by one and then
enable those once we figure out the problems.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Adding support of Chain Noise Calibration for 6000 series NICs.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When instructing the microcode to use just a single
chain when we have power saving enabled, we should
also tell the AP that we are doing SM powersave.
However, using a single chain doesn't actually have
any power saving advantage while idle -- measurements
show that the power consumption is no different when
using one vs. two or three chains.

Therefore, always instruct the microcode to use all
chains.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We never have four chains, but let's fix the typo
while we noticed it. You count 0, 1, 2, 3, not
0, 1, 2, 4 :)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Today's implementation allow LED to blink based on the traffic
condition. We introduce an additional LED mode that reflects the RF
state.

The supported LED modes after this are:
  IWL_LED_BLINK (current/default) - blink rate based on current Tx/Rx
                                    traffic
  IWL_LED_RF_STATE (new) -
    LED OFF: No power/RF disabled, the LED is emitting no light
    LED ON:  Powered/RF enabled, the LED is emitting light
             in a stable non-flashing state.

In order to provide the flexibility to support different LED
behavior per user/system preference we add "led_mode" iwlcore module
parameter.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Update PCI Subsystem ID for 60x0 series based on HW SKU. Adding new SKU
for "ABG" and "BG" only devices.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Update PCI Subsystem ID for 1000 series based on HW SKU. Adding new SKU
for "BG" only devices.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In order for uCode to select the valid antennas for transmit, driver
need to configure the allowed tx antennas through host command.

The TX_ANT_CONFIGURATION_CMD should be used for 5000 series and up
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Current rate scale algorithm fluctuates between different MIMO modes fairly
rapidly, causing widely varying performance. These fluctuations occur because in
the rate_scale tables for expected throughput the values are not very different
for different modes.

However, when aggregation is turned on and MAC overhead is reduced, the
expected throughput for different MIMO modes grows and different modes have
vastly different performance. Add expected throughput tables for this case.

We also need to keep track of aggregation status per-station, so we add the
"is_agg" field to struct lq_sta.

Also includes cleanup of comments and variable names in/around the affected
code.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

OR-in AMPDU flags rather than assigning them.  This lets the TX status for
aggregated packets be processed by rs_tx_status.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Cut down on redundant code, reorganize structure, and add/improve comments.
Should contain no functional changes.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Instead of hardcode module parameter's permissions, use pre-defined.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Update EEPROM version requirement for 1000 and 6000 series of NIC
for EEPROM version verification.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Allow user to change protection mechanism for HT between RTS/CTS and
CTS-to-self through sysfs:

Show current protection mechanism for HT
   cat /sys/class/net/wlan0/device/rts_ht_protection

Change protection mechanism for HT (only allowed while not-associated)
CTS-to-self:
   echo 0 > /sys/class/net/wlan0/device/rts_ht_protection
RTS/CTS:
   echo 1 > /sys/class/net/wlan0/device/rts_ht_protection
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When 802.11g was introduced, we had RTS/CTS and CTS-to-Self protection
mechanisms. In an HT Beacon, HT stations use the "Operating Mode" field
in the HT Information Element to determine whether or not to use
protection.

The Operating Mode field has 4 possible settings: 0-3:
Mode 0: If all stations in the BSS are 20/40 MHz HT capable, or if the
BSS is 20/40 MHz capable, or if all stations in the BSS are 20 MHz HT
stations in a 20 MHz BSS
Mode 1: used if there are non-HT stations or APs using the primary or
secondary channels
Mode 2: if only HT stations are associated in the BSS and at least one
20 MHz HT station is associated.
Mode 3: used if one or more non-HT stations are associated in the BSS.

When in operating modes 1 or 3, and the Use_Protection field is 1 in the
Beacon's ERP IE, all HT transmissions must be protected using RTS/CTS or
CTS-to-Self.

By default, CTS-to-self is the preferred protection mechanism for less
overhead and higher throughput; but using the full RTS/CTS will better
protect the inner exchange from interference, especially in
highly-congested environment.

For 6000 series WIFI NIC, RTS/CTS protection mechanism is the
recommended choice for HT traffic based on the HW design.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The chain settings we currently use in iwlwifi are
rather confusing -- and we also go by the wrong
settings entirely under certain circumstances. To
clean it up, create a new variable in the current
HT config -- single_chain_sufficient -- that tells
us whether we need more than one chain. Calculate
that based on the AP and operating mode (no IBSS
HT implemented -- so no need for multiple chains,
for station mode we use the AP's capabilities).

Additionally, since APs always send disabled SM PS
mode, keeping track of their sm_ps mode isn't very
useful -- doubly not so for our _own_ RX config
since that should depend on our, not the AP's, SM
PS mode.

Finally, document that our configuration of the
number of RX chains used is currently wrong when
in powersave (by adding a comment).

All together this removes the two remaining items
in struct iwl_ht_config that were done wrong there.

For the future, the number of RX chains and some
SM PS handshaking needs to be added to mac80211,
which then needs to tell us, and the new variable
current_ht_config.single_chain_sufficient should
also be calculated by mac80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Show version number along with dumping NVM data, the version information
being removed from sysfs, add it back to debugfs to help debugging.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Daniel Halperin pointed out that the naming
here is rather inconsistent with at least 3
different names being used for one thing in
different contexts. Rename the struct to
iwl_ht_config (rather than iwl_ht_info) and
use ht_conf as a variable for it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Adjust led blink rate to compensate on a MAC Clock difference on every
HW. Led blink rate analysis showed an average deviation of 0% on 3945,
5% on 4965 HW and 20% on 5000 series and up.
Need to compensate on the led on/off time per HW according to the
deviation to achieve the desired led frequency
The calculation is: (100-averageDeviation)/100 * blinkTime
For code efficiency the calculation will be:
    compensation = (100 - averageDeviation) * 64 / 100
    NewBlinkTime = (compensation * BlinkTime) / 64
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>